Search Documents

By D. R. Mash

A strong yield point with attendant enhanced mechanical properties was found in commercially pure beryllium under certain conditions of heat treatment. Beryllium specimens also responded to both quench and strain aging treatments. Based on these results, a possible means of obtaining increased normal temperature mechanical properties is suggested. COMMERCIALLY pure beryllium has been found to exhibit the yield point phenomenon and several other aging manifestations under certain conditions of heat treatment. This behavior is not surprising in view of the present accumulation of experience regarding such effects in numerous metals; but in addition to extending this experience to include beryllium, the present study is of interest because aging effects are generally associated with the presence of small amounts of solute elements. The well known lack of tensile ductility in beryllium at normal temperatures is also considered to be due to impurities in some way. In the present investigation, the view was taken that beryllium of commercial purity (greater than 98 pct) should be considered as a dilute alloy and that precipitation phenomena may well exist which could lead to enhanced mechanical properties. In connection with this possibility, published data on the variation of mechanical properties with temperature are of interest. For example, Fig. 1 illustrates the variation of ductility (percentage of elongation) and ultimate strength as a function of temperature for beryllium of various histories.* Although these curves are somewhat schematic in nature, they clearly indicate the possibility that precipitation of an unstable phase and/or aging effects occur during tests in the region 400" to 700°C. The existence of such behavior should be recognized as affecting the properties of the commercial material and perhaps can be employed advantageously. Experimental Method All testing was done at room temperature using a Baldwin universal testing machine. A microformer extensometer was used in conjunction with a micro-former-type stress-strain recorder. All tests were conducted at constant loading rate, the slowest rates being used. This corresponded to 120 lb per min in the 1200 lb full scale range and 300 lb per min in the 6000 lb full scale range. After the rate of loading was set in the elastic range of the material during the early part of the test, no further adjustments were made, allowing the test to proceed at that setting. In the plastic region of the curve above the yield region, strain rates of from 0.002 to 0.006 in. per min were regularly obtained. All experimentation was carried out on specimens machined from the same lot of beryllium, lot No. Y5036BP. Table I shows the chemical analysis as furnished by the supplier, Brush Beryllium Co., as well as the standard specifications to which commercial beryllium is produced. Both 1/4 in. thick hot pressed plate and ½ in. round hot pressed and warm extruded rods were obtained. The history of the material is reported to be as follows: 1—Beryllium metal plates, produced from a standard hot pressed QMV beryllium metal block 4x15x40 in., were cut off and finished machined to 1/4x6x12 in. flat plates. The original hot pressed block was made by hot pressing —200 mesh vacuum cast attri-tioned powder at about 1050°C under vacuum. 2—Beryllium rod was hot pressed and warm extruded. Extrusion billets were machined from the regular hot pressed blocks followed by extrusion at 425°C. The extrusion was done without jacketing, and graphite was used as a lubricant. The rods were then straightened at 720 °C, after which they were annealed at 800°C for 15 min. Both flat tensile specimens and round tensile specimens were tested. The former were machined from the plate stock into standard specimens according to specifications shown in ASTM E8-52T. The nominal cross-section was 0.25x0.500 in. and the gage length was 2 in. The round specimens were

Jan 1, 1956

By A. D. K. Laird, C. A. Johnson

Drag coefficients for a cylinder being towed through water at constant velocity and also at constant linear acceleration were measured. Drag coefficients for constant velocity towing showed reasonable agreement with previous results. The drag coefficients found for constant acceleration showed little correlation with either the magnitude of the acceleration or the value of the modulus AD/V2 and tended to be slightly lower than those for constant velocity. INTRODUCTION For the design of offshore structures, wave forces acting on immersed cylinders are of importance. Several investigations have been made of these forces and of how they can be predicted from wave theories. A paper by Crooke' summarizes much of the work already done. More recent research by the Wave Research Laboratory at the University of California, Berkeley, has added much to the body of data collected under ocean wave conditions, but has not found a reliable method of force prediction from basic theories of wave motion. The present investigation is part of a long-range program to collect data with which to test current and future theories and correlations. The immediate objective was to measure drag forces on a circular cylinder subjected to linear accelerations over the range of Reynolds numbers between l04 and 105 where the drag coefficient was a constant for constant velocities. In particular, the effect of constant acceleration from rest and from uniform motion was to be investigated. The effect of acceleration may be evaluated in terms of drag coefficients. A useful resistance coefficient, C, is defined by the equation for total drag force, D, exerted by the fluid on the cylinder. DT =CSp V2/2.........(1) The coefficient C may be plotted as a function of the parameter AD/V2. Here D is the diameter and S is the projected area of the cylinder. The acceleration and velocity are A and V. The mass density of the fluid is p. An alternate drag coefficient, C, corresponds to the total force of the fluid opposing the motion minus the virtual mass force. This drag coefficient, arising from the velocity of the fluid, may be compared with that for the same cylinder in uniform motion. The similarities and differences between this coefficient as calculated for accelerated and for steady motion are of interest in the inverse process of predicting drag forces on cylinders under arbitrary conditions. One serious difficulty in this method is the specification of the virtual mass which depends also on the flow picture about the cylinder.1 EXPERIMENTAL EQUIPMENT The experiment was performed in the combination wave and towing tank at the Engineering Field Station of the University of California. The tank is 200 ft long, 8 ft wide, and 6 ft deep. The tow carriage is externally propelled by a cable, and the velocity of the carriage is maintained essentially constant by means of an am-plidyne. For the purpose of the present investigation, the speed control of the amplidyne was modified by inserting a linear speed control rheostat, which was rotated at a constant speed by a small d-c motor equipped with a slip-clutch. Accelerations which were constant over a reasonable length of time were thus produced. The magnitude of the acceleration depended upon the speed of the d-c motor and the limiting speed of the carriage. Data were obtained for a range of accelerations of 2 to 10 ft/sec,2 and a range of velocities of 2 to 15 ft/sec. An accelerometer (Statham Type C-2-350) with a range of ±2g was attached to the carriage and connected to a Brush analyzer and penmotor. A continuous coil of wire with 10 turns/ft wound around a fixed wooden form extending for a distance of 40 ft along the length of the tank was connected by an electrical contact mounted on the carriage to a Brush analyzer and penmotor, to give the time-position history for each run. The test cylinder was machined from solid aluminum alloy, 17-ST. to a diameter of 1.250 in., and could be

Jan 1, 1957

By B. K. Larkin, H. R. Bailey

One of the most complicated and potentially one of the most promising secondary recovery methods is that of underground combustion. A number of field tests1,2,3 have been performed recently, apparently indicating that the underground combustion process is technically feasible. Relatively little has been published concerning laboratory or theoretical investigations of the underground combustion process. A few results of laboratory tube runs have been published4,5 and these data are valuable in understanding the process. The tube run data also emphasize the complexity of the thermal recovery process. Under various conditions, problems in heat transfer, multiphase fluid flow and combustion rates arise. For example, at low temperatures the combustion process proceeds so slowly that the front cannot be propagated. It is a problem in heat transfer to predict what injection rate of air is necessary to sustain combustion in a particular reservoir. Certain fluid flow aspects of underground combustion have been studied by Wilson, et a13. In the development of some of the flow equations, assumptions of adiabatic combustion were made. Vogel and Krueger1 have devised an analog model of the heat conduction process for a constant temperature cylindrical source moving radially outward in a homogeneous conducting medium. Jenkins and Ramey7, in a discussion of the Vogel and Krueger paper, present an analytical solution of a heat conduction problem related to problems considered by Vogel and Krueger. In the present paper an idealized model of the heat conduction problem is considered, which is more general than the model of Vogel and Krueger or Jenkins and Ramey. In particular, initial well heating, vertical heat losses and arbitrary frontal velocities are included. Equations for the temperature are obtained in terms of integrals. These integrals have been evaluated numerically for the case of frontal movement corresponding to a constant air injection rate and the case of constant frontal velocity. These results are presented graphically. From these graphs one may estimate conditions under which nearly adiabatic temperatures are obtained. The application of these results requires some knowledge of reservoir thermal properties, combustion rates and residual fuel content. Assuming no vertical losses it is possible to obtain explicit evaluations of these integrals in the linear con- stant velocity case and in the radial case corresponding to a constant air injection rate. PRESENTATION OF RESULTS The geometry of the radial system is illustrated in Fig. 1 where the reservoir is represented as a slab of thickness h. By making an energy balance for an infinitesimal volume, one obtains the following equation. T= x T+F(z.r).........(1) where F (z,r) =HWv1/pc (r-r1), if z h/2 = 0, if z >h/2 . In Eq. 1, V- represents the Laplacian operator and 8 is the Dirac delta function. Eq. 1 is the well-known diff-sion equation with a source term and may be applied to a linear system. For example, if the source is moving in the direction of the x axis, then the argument of the delta function is x - 1,. In deriving Eq. 1 the following approximations were made concerning the actual combustion process: (1) all heat transfer is by conduction in a homogeneous medium, (2) the formations bounding the reservoir have the same thermal properties as the reservoir, (3) the combustion fuel is consumed instantaneously as the front arrives, (4) there is a constant fuel concentration

By Paul A. Schafer

BALATOC mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.1 The region is a deeply dissected plateau, ranging in altitude from 3000 t0 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. 1): q6, 231 and 364, which strike about N.70°E. and dip 5o to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.45°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. NORTHEAST FAULTS The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on Pine fault and q6 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar No. I, and Sun

Jan 1, 1942

By D. F. Kelsall

The hydraulic cyclone, in simple or modified form, is finding increasing application in metallurgical processing. In this article, the author considers several aspects of conventional applications, less conventional applications and some potential uses of modified cyclones. Information concerning the mechanism of separation within a cyclone and the effect of the major variables is summarized. During the past twenty years, and especially in the last decade, hydraulic cyclones have found increasing application in metallurgical processing as classifiers and, under special circumstances, as thickeners. To a more limited extent cyclones have been used to extend heavy, or dense, medium separation into the finer size ranges, and several attempts have been made to separate dispersions of immiscible liquids with a view to use in the field of liquid-liquid extraction. A large proportion of published work reports incomplete data, applicable only to particular systems. The more useful papers, covering data of relatively wide significance, have been reviewed recently in considerable detail1,2 and no attempt will be made to cover the same material in the present paper. However, before considering several aspects of conventional application, less conventional applications and some potential uses of modified cyclones, it is considered pertinent to summarize information relating to the mechanism of separation within a cyclone and the effect of the major variables. LIQUID FLOW PATTERNS At any point within a simple cyclone the liquid velocity may be resolved into three components, i.e., the tangential or swirling velocity (v), the vertical velocity (w), and the radial velocity (u). The relative values of these components at selected positions within a typical cyclone have been established for water. 3 The extent to which similar flow patterns exist in systems of considerably higher viscosity, or apparent viscosity, operating under conditions of reasonable pressure drop, is not known with precision, but indirect evidence indicates that up to approximately five centipoise there is no marked change. Beneath the bottom of the vortex finder, envelopes of constant tangential velocity are cylinders coaxial with the cyclone, and, at any horizontal level, starting from near the conical wall, this component of velocity increases with decrease in radius (r) according to the relationship vrn = constant (where 0 < n < 1) This holds to regions near the center of the cyclone where v reaches a maximum value at a radius somewhat smaller than that of the inside wall of the vortex finder. At this point, the centrifugal acceleration, v2/r reaches a maximum value. As the radius is further decreased the tangential velocity decreases so that v = r. Above the bottom of the vortex finder there is a tendency for the first relationship to persist to near the outside wall of the vortex finder, until v reaches a maximum and then decreases rapidly as the wall is approached. The two most significant features of the vertical velocity distribution are an approximately conical Table I. List of Symbols v = liquid tangential velocity at any point in the cyclone w = liquid vertical velocity at any point in the cyclone u = liquid radial velocity at any point in the cyclone r = radius from cyclone axis to any point ? = half angle of conical portion of the cyclone ?= fluid viscosity d = particle diameter s = liquid specific gravity p = particle specific gravity d50 = the particle diameter which distributes 5090 to overflow, 50% to underflow e = overflow diameter, in. b = feed diameter, in. G = gpm of feed slurry

Jan 1, 1963

By N. S. Stoloff, R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-Co and Fe- V alloys containing up to 25 pct solute have been studied in the temperature range 25° to - 196°C. The microyield stress is independent of temperature for all alloys studied, while the temperature dependence of the ordinary yield stress is large and comparable to that for unalloyed iron. An alloy-softening phenomenon is observed for many alloys relative to unalloyed iron, and appears to be a consequence of removal of inter-stitials from solution and their subsequent agglomeration. The ductile to brittle transition temperature is increased markedly by both cobalt and vanadium. Transmission electron microscopy observations reveal that cross slip and cell formation are restricted with increasing solute, which can account for many aspects of yielding and fracture behavior. IRON and other metals of bcc structure slip on many planes of the (111) zone at moderate and elevated temperatures, giving rise to wavy glide. At low temperatures, however, there is a tendency for slip to be restricted to planes of only one or two crystallographic types; in the case of Fe-Si alloys for example, (110) glide predominates, giving rise to planar slip bands."&apos; Restriction of cross slip at low temperatures in iron has been linked by Brown and Ekvall3 to increased strain hardening in the preyield microstrain region, leading to an apparently large temperature dependence of the yield stress. Support for this view has been provided by Lawley and Gaigher4 from a transmission electron microscope study of molybdenum. They concluded that dislocations at lower temperatures, by virtue of their inability to change planes readily, are unable to interact and annihilate, leading to an increase in internal stress and work-hardening capacity. Restriction of cross slip at low temperatures has also been suggested to be an important factor in determining the ductile to brittle transition of single-phase solids, including metals of bcc structure.5 It is pertinent to note that most solute elements tend to raise the ductile to brittle transition temperature of poly crystalline ferrite,6,7 although in some cases, e.g., Fe-Cr7 and Fe-Al,8 the dilute alloys may actually yield at lower stresses than unalloyed iron. It appears, therefore, that solute elements may have an effect analogous to lowering the test temperature with regard to restricting cross glide. Such an effect has indeed been observed in the ionic alloy system KCl-KBr,9 in which bromine atoms, although causing little misfit and consequently little effect on the yield stress of KC1, have a pronounced effect in restricting wavy glide and inducing brittleness. The purpose of the present investigation was to determine the effects of selected solute atoms on the yield stress and fracture behavior of iron, and to elucidate in turn how the slip character was related to these properties. Since it is known that interstitial atoms exert a strong influence on the mechanical behavior of iron, the solute elements chosen for study were vanadium, which reacts strong with interstitials,10 and cobalt, which does not form highly stable interstitial compounds." EXPERIMENTAL PROCEDURE Four-pound ingots of each of the following alloys were vacuum-melted in zirconia crucibles: Fe-1, 5, 10, 25 at. pct Co, and Fe-1, 4, 10, 20 at. pct V. An ingot of unalloyed iron from the same original stock as that used for the alloy was remelted under similar conditions to eliminate variations in interstitial content arising from differing thermal histories. Chemical analyses of the iron, cobalt, and vanadium melt stock are listed in Table I. All ingots were rolled and swaged, commencing at 850°C, to 1/4-in.-diameter bar. The bars were then annealed at 850°C for 1 hr (except that the 10 and 20 pct V alloys were heated for 2 hr) to give a uniform equiaxed grain size of about 0.05 mm. Tensile samples of 0.125 in. diameter by 0.8 in. gage length were utilized for studies of the ductile to brittle transition. A second set of tensile samples were utilized for microstrain experiments in which strain sensitivity of 1 x 10"6 was achieved by a capacitance method.3 Cylindrical compression samples 0.250 in. diameter by 0.4 in. long also were prepared to study the influence of composition on the macroscopic yield stress, and for metallographic analyses of defor-

Jan 1, 1965

By Horace Pops

Martensitic transformation has been studied during cooling and heating in ß-phase Cu-Zn alloys to which small additions have been made of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, and Sb. The start and finish of the martensitic reaction and the variation of transformation temperature with third-element content were determined by electrical-resistivity measurements from alloys which had either constant zinc contents or constant values of electron concentration. All of the third elements, except nickel, lowered the transformation temperature if the results were plotted along the lines of constant zinc contents in each ternary system. A significant difference in the rate of lowering of the transformation temperature per atomic percent of the third element was observed for elements which had the same nominal valence. No systematic variation of transformation temperature with the valence of the third element was observed. It is suggested that the observed increase in transformation temperature for nickel-bearing alloys is due to the transfer of electrons from the conduction band of the alloy to virtual bound states. However, electron concentration is not the most important factor controlling the instability of the 0 phase. The transformation temperatures of the ternary alloys can be predicted from the following approxilnate expression: Ms (°K) = +3280 - 80 Zn + 8 Ni - 30 Ag - 12 Au - 140 Cd -90 Ga- 145 In - 80 Ge -175 Sn - 120 Si - 150 Sb MOST binary ß -phase alloys based upon the noble metals copper, silver, and gold are unstable at low temperatures and transform spontaneously by a martensitic reaction. This transformation has been studied recently in the ordered bcc ß&apos;-phase Cu-Zn binary al1oys1,2 where the transformation temperature is below the room temperature and decreases with an increase in zinc content. It has been reported that the transformation temperatures can be raised above room temperature by small additions of a third element such as silicon3,5 or gallium,4,5 but no quantitative study has been made. The transformation temperature of different binary alloys can be altered by third-element additions. For example, it was shown that nickel and copper may have a large effect on the Ms temperature of CU-Al6 and Au-cd7 alloys. The present investigation was made to determine systematically the influence of various third elements on the martensite-transformation temperature of Cu-Zn ß-phase alloys. Since these alloys have an electronic origin,&apos; alloy compositions were chosen so that the transformation temperatures could be determined at constant zinc contents or at constant values of electron concentration. I) EXPERIMENTAL PROCEDURE Ten ternary alloy systems were obtained by adding nickel, the noble metals silver and gold, and some B-subgroup elements to a Cu-Zn matrix. These are arranged according to their rows and columns in the Period Table as follows: Each ternary alloy was prepared by melting and casting weighed quantities of high-purity metals (99.99+ pct) in sealed quartz tubes under a partial pressure of helium to make a 4-g ingot. The molten alloys were shaken vigorously and then quenched in water. Since the weight loss was negligible, the compositions of the ingots after casting and annealing were assumed to be the same as the nominal compositions. The ingots were homogenized after casting in helium-filled Vycor tubes for 24 hr at temperatures between 750" and 810 C and quenched into brine. Metallographic examination revealed that all alloys were homogeneous, poly crystalline ß-phase alloys, and that the grain size was in the range 1 to 5 mm. Electrical-resistivity measurements were made to determine transformation temperatures of the ternary alloys during continuous cooling or heating. Transformation temperatures of the ternary alloys can be determined by electrical-resistivity measurements since the resistance of the martensitic phase is much higher than that of the 0&apos; phase. The technique has been described previously in connection with a study of Au-Zn alloys.9 The reproducibility of transformation temperature was approximately ±6°C. II)RESULTS A hysteresis was always observed in electrical-resistivity curves and was usually less than about 12°C.

Jan 1, 1967

By R. E. Powers, E. H. Kinelski, H. A. Morrissey

A group of 17 American blast-furnace sinters, an American open-hearth sinter, an American iron ore, and a Swedish sinter were used to evaluate testing methods adapted to appraise sinter properties. Statistical calculations were performed on the data to determine correlation coefficients for several sets of sinter properties. Properties of strength and dusting were related to total porosity, slag ratio, and total slag. Reducibility was related to the degree of oxidation of the sinters. THIS report to the American iron and steel industry marks the completion of a 1949 survey of blast-furnace sinter practice sponsored by the Subcommittee on Agglomeration of Fines of the American Iron & Steel Institute. The use of sinter in blast furnaces, sinter properties, raw materials, and sinter plant operation have been reported recently.1,2 After preliminary research and study," test procedures were adapted to appraise the physical and chemical properties of sinter to determine what constitutes a good sinter. During the 1949 to 1950 plant survey each plant submitted a 400-lb grab sample to research personnel at Mellon Institute, Pittsburgh, Pa. A 400-lb sample was also submitted from Sweden. In addition, 2 tons of group 3 fines iron ore were obtained from a Pittsburgh steel plant. The following tests were performed on the iron ore sample and on the 19 sinter samples: chemical analysis; impact test for strength and dusting; reducibility test; surface area measurements, B.E.T. nitrogen adsorption method; S.K. porosity test; Davis tube magnetic analysis; X-ray diffraction analysis for magnetite and hematite; and microstructure. Results of these evaluations are discussed in this paper and supply a critical look at testing procedures used to determine sinter quality. Sinter Tests and Results Each 400-lb grab sample of sinter was secured at a time when it was believed to represent normal production practice at each plant. It was not possible to use the same sampling procedures throughout the survey; consequently samples were taken from blast-furnace bins, cooling tables, and railroad cars. These were very useful for evaluation of test methods, since they were obtained from plants with widely divergent operations. With the exception of Swedish sinter and sinter sample N, which were produced on the Greenawalt type of pans, all survey sinters were produced on the Dwight-Lloyd type of sintering machines. Sinters submitted for test were prepared in identical manner by crushing in a roll crusher (set at 1 in.), mixing, and quartering. To secure specific size fractions for tests, one quarter of the sample was crushed in a jaw crusher and hammer mill to obtain a —10 mesh size. The remainder was screened to obtain specific size fractions. The group 3 fines iron ore was dried and screened and samples were taken from selected screen sizes to be used for various tests. Prior to testing, each ore sample except the —100 mesh fraction was washed with water to remove all fine material and was then dried. This iron ore, a hematitic ore from the Lake Superior region, was used as a base line for comparing results of tests on sinters. The iron ore did not lend itself to impact testing, since it was compacted rather than crushed in the test, and no impact tests are reported. However, the iron ore was subjected to all remaining physical tests to be described. Chemical Analysis: Table I presents chemical analyses performed on the survey sinter samples. Included in this table are data obtained from determination of FeO and the slag relationships: CaO + MgO and total slag (CaO + MgO + SiO, SiO2 + Al2o3 + TiO2). The percentage of FeO was used as an indication of the percentage of magnetite in the sinter. It was believed that slag relationships could be correlated with sinter properties. During initial determination of FeO great disagreement arose among various laboratories, both as to the results and the methods of determining values. Table I lists the values of FeO resulting from the U. S. Steel Corp. method of chemical analysis,&apos; which reports the total FeO soluble in hydrochloric and hydrofluoric acids (metallic iron not removed) with dry ice used to produce the protective atmosphere during digestion. Use of dry ice was a modification required to obtain reproducible results. In this method, the iron silicates and metallic iron are believed to go into solution and are therefore reported as FeO. This is important, for in the study of the microstructure of sinters, glassy constituents suspected of containing FeO as well as crystallized phases of undetermined identity which may also contain FeO have been observed. Strength Test by Impact: In evaluating sinter quality, one of the properties stressed most by blastfurnace operators is strength. This strength may be described as the resistance to breakage during handling of sinter between the sinter plant and the blast-furnace bins. It is also the strength necessary to withstand the burden in the blast-furnace. After

Jan 1, 1955

THERE can be little doubt in the mind of anyone of the great interest which has been provoked in the mining and petroleum industry by the com-paratively new geophysical methods of prospecting, after the sessions at this year&apos;s meeting of the Institute. Not only were the sessions very well attended but every¬one seemed most attentive. Although the discussion was somewhat limited in general, that may well be at-tributed to the newness of the subject. Two sessions on this subject were planned originally, but these gave insufficient time for the presentation of all the papers prepared and a third session was abso-lutely necessary. The first meeting dealt entirely with the gravity methods and was completed in the scheduled time owing to the fact that but two of the five papers listed were read. The second session was devoted to magnetic and electrical methods, the completion of which had to be carried over into the third period of geophysics. The first session on geophysical prospecting, and in-cidentally the first scheduled Institute meeting devoted entirely to this subject, was most appropriately opened by E. L. DeGolyer, the chairman of the session. It was through the efforts of Mr. DeGolyer that the first gravity work, as applied to prospecting, was under-taken in this country. Again most appropriately, the first paper presented was given by Donald C. Barton, who carried on the first work with the Eötvös torsion balance in America and aided materially in its development. A subject, the theory of which is so difficult to understand as it is generally presented, was so clearly illustrated and ex-plained by the speaker that even a novice could grasp the fundamentals. Dr. Barton, in showing actual re-sults obtained in torsion balance surveys with the in-terpretation of the sane and later drilling records, was free in stating that there are many limitations to the field in which this and the other geophysical instruments may be successfully employed. This paper called for considerable discussion relative to the application of the torsion balance to gravity surveys over various types of structures. During the course of this discus-sion a very important point was emphasized by the chairman, namely, that for successful application of any or all of the scientific methods of prospecting, a back-ground of experience is absolutely necessary to serve as a basis for further work. This can only be secured by contributions from the results of actual prospecting work.

Jan 3, 1928

R. B. Sosman, * Kearny, N. J.—Mr. Sweetser brought out that in certain blastfurnace slag compositions a change of one or two tenths of a per cent may be quite significant. That is true not only of blast-furnace slags but of other compositions as well. We have all been up against the necessity of having to plot out equilibrium diagrams of this kind on a big enough scale so that we could actually use them, the

Jan 1, 1935

R. B. Sosman, * Kearny, N. J.—Mr. Sweetser brought out that in certain blastfurnace slag compositions a change of one or two tenths of a per cent may be quite significant. That is true not only of blast-furnace slags but of other compositions as well. We have all been up against the necessity of having to plot out equilibrium diagrams of this kind on a big enough scale so that we could actually use them, the

Jan 1, 1935

By Kingman, Robert I.

SUFFICIENT testing has been .performed with the Dutch State Mines Cyclone for thickening and desliming flotation feed at the concentrator of the National Lead Co., Tahawus, N. Y., to prove its application for this work. It is the purpose of this article to present some of the test results, operational details and advantages of cyclone thickening and classification. The metallurgy of the mill operation was described by Frank R. Milliken, assistant manager of the titanium division.

Jan 1, 1950

Percussion drilling with tungsten carbide insert button bits ranks among the most significant advances in both underground and surface drilling in medium and hard rock formations. Getting top performance and life from these upfront components is not particularly difficult if one pays attention to the basics in operation and maintenance. For some reason, a few of the essential operating and maintenance steps for getting the most from these tools seem to have gotten turned around; instead of operating at the near optimum levels, some miners, in following myths or misunderstandings about them, are shortchanging their optimal utilization. Let&apos;s examine the two most harmful ones.

Jan 8, 1978

Arizona E. P. MATHEWSON, Chairman F. W. MACLENNAN, First Vice-chairman CLYDE E. WEED, Second Vice-chairman E.D. GARDNER, : Secretary-Treasurer Box 4097, University Station, Tucson, Ariz. ARTHUR CROWFOOT G.H. DOWELL HENRY F. EASTER R.D. LEISK Boston Meets first Monday each month, October to May, inclusive GEORGE, W. METCALFE, Chairman ROBERT S. WILLIAMS, Vice-chairman F. LEROY FOSTER, Secretary-Treasurer Rooms G-202, Mass. Inst. of Tech. Cambridge, Mass. FREDERICK K. MORRIS GEORGE A. PACKARD

Jan 1, 1934

By P. Sen, H. B. Barani, P. Sen Gupta

A critical review of the various separation efficiencies reported in literature has been made. Most of the relationships used for evaluating the performance relate to screening, classification, or concentration operations and are applicable to single-stage, two-component systems only. In the present work, a much simpler approach has been used for assessing the separation process irrespective of the type of operation and this has been extended further to obtain an expression for a multicomponent feed and multiproduct (from a multistage operation) system.

Jan 1, 1980

R. W. Raymond, New York City: From a study of Mr. Johnson&apos;s paper, I conclude that his apparatus is simple in construction and operation, and imitates in a revolving machine the movements of hand-shoveling. It does what a man would do in removing sand from the waste-water with a perforated shovel. I am sorry to say that I fear the present condition of the brown-ore mining industry in the East, as long as

Jan 1, 1899

By D. D. Dunkin

SANDSTONE has been prepared for glassmaking purposes, and marketed from the White River Valley in-Arkansas at Guion, Izard County, since about 1910-soon after the completion of the White River Branch of the Missouri Pacific R. R. Co. Until 1921, operations were somewhat spasmodic and ended in many failures. In that year a plant was built by the Silica Products Co., Inc., and since that time the operation has been continuous and steady. The land is held under leases, covering about 30 sq. mi. of the best sandstone adjacent to the railroad. Most of the product is shipped to glassmakers. GEOLOGY The St. Peter sandstone is rather widely distributed in north central Arkansas and- is exposed most prominently in outcrops along the slopes of the White River Valley and its tributaries that form the division between the Boston Mountains to the south and the Salem Plateau of the Ozarks to the north. It is of Ordovician age and is generally underlain by Cotter dolomite and capped by Plattin limestone, except in the vicinity of Bellefonte and Everton. At those places, it is a massive cross-bedded, laminated, saccharoidal sandstone; underlying it is the Everton limestone and overlying it, the Joachim magnesium limestone. The sandstone at Everton contains numerous phosphatic pebbles and inclusions of sandy limestone. The irregularity of cross-section, the evidence of sorting action and the phosphatic pebbles appear to be indications of secondary deposition.

Jan 1, 1928

By A. J. Griest, P. D. Frost, J. R. Doig

During the past 5 years, research directed toward the development of titanium alloys having improved strength-ductility relationships and heat treatability has been carried out at Battelle for the U. S. Air Force.1"3 In the course of this work, a method of heat treating ß-stabilized titanium alloys was developed which produced a wide range of useful properties.4 The heat treatment consisted of two steps: a) solution treating at temperatures in the a-ß phase region, and b) overaging at a lower temperature in the range 800°to 1100°F. Corollary to the alloy development work, research was conducted on the mechanism of the heat-treatment reaction. The investigations of Frost and co-workers on isothermal transformation in Ti-Cr5 and Ti-Mn8 alloys disclosed the existence of the transition phase, w, during the course of the decomposition of metastable ß phase. Subsequent work at Battelle7,8 &apos;and at Case Institute by Brotzen and co-workerss further clarified the nature of the decomposition process. Beta decomposition was found to proceed by the following series of reactions: 1 2 3 4 a + Ti, My (in eutectoid systems). ßo, ßr, and ßU refer to ß phase of original, enriched, and ultimate alloy contents, respectively. Omega is a transition phase having a complex structure. 10-13 Step 4, of course, occurs only in ß-eutectoid systems. This paper presents data correlating transformation behavior with mechanical properties for the following alloys: Ti-8Mn, Ti-8Mn-2A1, Ti-4Mn-4A1, Ti-6Al-4V, and Ti-4Fe. The isothermal decomposition of ß in titanium-manganese alloys of similar composition has been investigated by Frost and coworkers8 and the effect of various annealing treatments on alloys in this system has been studied by Holden, Ogden, and Jaffee.14 The compositions Ti-8Mn-2Al, Ti-4Mn-4A1, and Ti-6A1-4V, were studied in the present work in an effort to define more clearly the effect of aluminum on the response to solution and aging treatments. Ogden, Holden, and Jaffee15 have invesitgated the effect of aluminum on the response of a similar alloy (Ti-8.8Mn-2.46A1) to annealing treatments, and Luini and Lee16 have made an exploratory investigation of the heat-treatability of the Ti-4Mn-4Al alloy. The Ti-4Fe alloy was studied as an example of a moderate1y active eutectoid system. Holden, Ogden, and Jaffee 17 have studied Ti-Fe alloys and have presented some hardness data for aging at 400°C for alloys of Ti-2.56, 5.01, and 7.35 iron after quenching from the a-ß field (750°C). EXPERIMENTAL PROCEDURES The experimental procedures generally used in the precipitation-hardening study are outlined in the following sections. Departures from these techniques are noted in the discussions of the individual alloys. Table I presents the nominal and actual compositions of the alloys studied, together with the swaging and rolling temperatures. In all cases, these temperatures were in the a-ß field and the microstructures consisted of an equiaxed a-ß mixture. Melting and Fabrication—Except for the commer-

Jan 1, 1960

By Murray F. Hawkins, W. J. Ainsworth

In all types of subsurface pressure gauges the extension which occurs in the pressure-sensitive element is a function of the difference between the external (well or calibration) pressure and the internal pressure within the gauge, rather than a function of the external pressure only. The internal pressure is near atmospheric and depends upon (a) the quantity of air sealed within the gauge at the time of calibration or measurement, (b) the quantity of moisture (liquid water), if any, sealed within the gauge, and (c) the temperature at which the calibration or well measurement is made. Part of this correction for the change of internal pressure with temperature is taken care of by the customary temperature coefficient of the gauge. However, part of it is not, and while this portion may be only a few psi, it is nevertheless predictable or preventable, and should be considered in precision measurements. ERROR NO. 1 If air is sealed in the gauge at the same temperature and pressure for both the calibration and the well measurements, the usual temperature correction will take care of any difference between calibration and well measurement temperatures. However, if air is sealed within the gauge at temperature T1 and pressure P1 at calibration but at temperature T2 and pressure P2 for a well measurement, because different amounts of air are sealed within the gauge in each case, the internal pressure at. or corrected to, calibration temperature Tr will he different by where all temperatures and pressures are absolute. The calibration temperature is used, and not the well measurement temperature, because the usual temperature correction reduces the well measurements to calibration temperature. The correction term as calculated by the above equation is separate from. and in addition to, the usual temperature correction. Example: T, = 540°R, sealing temperature at calibration P, = 14.7 psia, sealing pressure at calibration T2 = 460°R, sealing temperature at well P2 = 14.7 psia, sealing pressure at well Tr = 660°R, calibration temperature AP = 660 [14.7/460 — 14.7/540] = 3.1 psi While this error is small even under these somewhat maximal conditions, it nevertheless represents a practical situation which did occur, and which as a matter of fact gave rise to this note. Where AP is positive, as above, the correction is added to the measured pressure; where negative, subtracted from the measured pressure. This correction should also be considered in successive calibration runs where the gauge, for example, may be warm from a previous calibration at an elevated temperature. ERROR NO. 2 Where a small quantity of moisture (liquid water) is sealed within the gauge at atmospheric conditions, the increased vapor pressure of the water at higher well or calibration temperatures will cause an increase in internal pressure. This moisture will come presumably from condensation within the gauge following temperature changes, from moisture on the operator&apos;s hands, and from atmospheric moisture (rain, mist, fog, etc.). Calculation shows that approximately 0.2 cc of water (three to four drops) is sufficient to saturate the air within an Amerada RPG-3 Gauge at 160°F, at which temperature the vapor pressure of water is about 5 psia. As the vaporization occurs in a sealed volume, the increase in internal pressure will be in excess of this 5 psi. At higher temperatures the pressures will be higher; however more water will be required to saturate the air within the gauge. Some experimental work was carried out with an Amerada RPG-3 Gauge at 200°F fitted with a 1,000 psi element, both with a dry recording chamber and with a small amount of water added. The results directly proved the existence of the error due to the presence of moisture, and, it is felt, indirectly, due to the differences in sealing temperatures and pressures, as both effects may be ascribed simply to an increase in the moles of gas within the recording chamber. SUMMARY In precision measurements the error introduced by sealing the gauge during a well test at a different temperature and pressure from that of calibration may be corrected for by using the equation presented, or it may be prevented by taking care always to seal the gauge at near calibration conditions. The error introduced by sealing moisture in the gauge may be prevented by taking care to keep moisture out of the gauge, or by removing the moisture by either warming or evacuating the gauge. Both of these errors are independent of the range of pressure measurement and the type of gauge, and are in addition to the usual temperature correction. ACKNOWLEDGMENT Appreciation is expressed to W. B. Kendall, Geophysical Research Corp., Tulsa, Okla., who pointed out the error from differences in sealing temperatures during some winter work in Canada. ***

Jan 1, 1956

The following letter was received from Prof. Kemp in reply to a telegram expressing the greetings of the members attending the Annual Meeting in New York. "Melbourne Beach, Fla. Feb. 17, 1916. Dear Mr. Stoughton: The welcome telgram from the members of the Institute, which you kindly trans-mitted to me, came safely yesterday and I catch the next available mail with a heart-felt acknowledgment. I cannot express to you how greatly the remembrance cheers and braces me during the days of patient waiting for the feeling of over-strain to fully pass, and for the time when I can again be back among the friends in the Institute who are very clear to me. While I cannot reach all the members who joined in the telegram I will ask you to say to such as are available that I am profoundly sensible of the thoughtfulness which prompted the message. I write from a little bungalow on the ocean. side of the half mile or more of sand dunes, thickly grown with palmetto, which separate the ocean from the Indian River. Two miles or more of Indian River still intervene between the little colony of Melbourne Beach and Melbourne on the mainland and on the Florida East Coast R. R. where the telegraph station is. I was thus unable to respond at once by wire. Sincerely yours, (Signed) J. F. Kemp."

Jan 4, 1916