Search Documents

By C Woodward

AT the Belmont mine of the Anaconda Copper Min-ing Co., Butte, Mont., a new double-drum electric main hoist and a single-drum electric auxiliary hoist have recently been placed in operation to meet the demand for greater hoisting depths, and to replace a steam-driven hoist which was inefficient and inade-quate for the new conditions. The ease of operation, safety, and efficient consumption of power of the main hoist all tend toward improved hoisting conditions. It consists of a 2150 hp. d. c. motor, directly connected to a shaft carrying two drums equipped with clutches and brakes. The auxiliary hoist consists of a 1000 hp. d. c. motor directly con-nected to a single drum provided with the necessary brakes. Fig. 1 shows the general arrangement of the complete installation, with idler towers and head-frame. The headframe is built of Bethlehem H and G rolled sections, equipped with two 12-ft. dia. cast steel sheaves for the main hoisting ropes. The sheaves are mounted 129 ft., 6 in. above the collar of the shaft; and above them trolleys are provided for their removal or repairs. Between the headframe and the hoist machinery are two idler towers for supporting the ropes on 3-ft. man-ganese steel idlers provided with roller bearings which fleet on a fixed shaft. As a city street is between- the mine headframe, and hoists, it is necessary to protect the thoroughfare from drippings of the preservative compound used on the ropes which pass over the street. For this purpose, at the point where the hoisting ropes cross the street ,a bridge of trusses, supported on columns and roofed with corrugated iron, is provided from property line to property line. Since one of the idler, towers is set close to the street, a part of the structure is built in-tegral with the street covering. The general design of idler tower as well as the covering over the street is shown at A in Fig. 1.

Jan 9, 1927

Commonwealth of Pennsylvania, Department of Internal Affairs, Topographic and Geologic Survey, Harrisburg, Pa George H. Ashley, State Geologist All available printed Bulletins may be obtained through the Commonwealth of Pennsylvania, Division of Documents. Where a price has been set on the publication, checks should be made out to the Commonwealth of Pennsylvania. A Syllabus of Pennsylvania Geology and Mineral Resources has recently been published by the Survey as Bulletin G1, and consists of a general survey of the state An appendix of this bulletin also gives a complete bibliography of Survey publications It will be sent upon request. The State Geological Survey has gone through several phases and reorganizations, publications of three of them being numerous and important A fire, in 1927, destroyed supplies of many of the papers of the present Survey. Available bulletins of the present Survey are: Bulletin M6: Bituminous coal fields of Pennsylvania, in 4 parts available as follows: pt 1, General description of coal, 50 cents; 3, Bituminous coal resources, 25 cents, 4, Analyses of bituminous coals, 25 cents Bulletin M10, Fire clays of Pennsylvania; Mll, Molding sands of Pennsylvania; M12, Anthracite culm and silt (1928); M13, Feldspar in Pennsylvania; M14, Magnetite deposits of French Creek (1931); County Report C1, Adams County, pt 1, Geology and geography (in press), County Report C2, Geology and mineral resources of Greene County (in press); Topographic and Geologic Atlas A5, New Castle Quadrangle (1929), $1; Topographic and Geologic Atlas A27, Pittsburgh Quadrangle (1929), $1; Topographic and Geologic Atlas A168, Lancaster Quadrangle (1930), $1. The present Survey has also issued a number of short mimeo¬graphed bulletins any of which will be sent upon request Briefly they are: No. 15, Mineral resources of Pennsylvania; 20, Iron ores; 28, Magnesite; 40, White clay deposits, Monroe County; 45, White clay deposits, central Pennsylvania; 47, Manganese, Eastern Pennsylvania, 48, Pyrite from bituminous coal mines; 59, Bog

Jan 1, 1933

By H. R. Joesting

Geophysical search for minerals is stepped up to meet requirements of expanded defense program - Seismic and electrical surveys become firmly established for ground-water and engineering investigations.

Jan 2, 1953

By J. Bruce Wagner, Roger L. Levin

Lattice-parameter measurements have been carrzed out at room temperature on undoped and on chromium-doped wustite as a function of oxygen concentration. Results may he expressed by for the undoped uustite. These data are in agreement with and extend the work of' Jette and Foole. The present results are consistent with the cation vacancy model. for metal- deficil wuslite, both undopen and doped. SEVERAL investigators have made room-temperature lattice-parameter measurements on wustite as a function of composition. Jette and Foote used these measurements to determine the phase limits of wustite. Willis and Rooksby and Benard have also measured the lattice parameters of wustite at room temperature, but their values of a. vary considerably from those of Jette and Foote. In conjunction with Studies' on the transition from surface-controlled heterogeneous reactions involving CO-C02 oxidation of metals, lattice-parameter measurements on undoped and chromium-doped wiistite have been performed. These studies are especially needed to clarify conflicting data of previous authors, to extend the data to the stability limits of wiistite as determined by Darken and urr,6 which include a larger range of existence than that found by Jette and Foote, and to test by X-ray means the role of chromium as a vacancy producer in wiistite.

Jan 1, 1967

By Paul Gordon

The distribution coefficient, k, of interest in zone refining is generally defined as the ratio of the solid to the liquid solubilities of one element in another at the normal melting point of the solvent. In practice, distribution coefficients are frequently calculated from solubilities at temperatures well below the melting point of the solvent, e.g., at a eutectic temperature. This is done because of the general lack of accurate data on the liquidus and solidus curves in most phase diagrams. The practice is equivalent to assuming that the liquidus and solidus curves are straight lines in the temperature range between the melting point of the solvent and the temperature at which data for the solubilities are known. It is recognized that the k values so derived may be in serious error; we have found evidence in recent zone-refining operations that a case in point is silicon in aluminum. The phase diagram found in the literature for silicon in aluminum indicates a eutectic on the aluminum-rich side at 12.5 at. pct Si and at 577°C,1 and a solid solubility of silicon in aluminum at this temperature of 1.59 pct.2 It also shows the liquidus and solidus as nearly straight lines from 577°C to the melting point of aluminum (660°C)1,2 The k value obtained from this data is 0.13. This is almost exactly the same as the k value (about 0.14)' obtained in a similar way for copper in aluminum. Yet we have found by mass-spectrograph analyses* of three bars of zone-refined aluminum that copper is efficiently removed from aluminum by zone refining but silicon is not. Two of the three bars of aluminum were zone-refined in our laboratories, the other in the laboratories of AIAG Metals, Inc. The former two bars, designated bars PG2 and PG3, were 30 in. long by 1 in. in diameter during refining; each was processed in a high-purity graphite boat* and kept under refining stage of the process consisted of thirty unidirectional zone traverses at rates of about 1 to 2 in. per hr, with a zone length of 1 to 2 in. At approximately the middle of the refining period a 6-in. piece of the impurity-laden finishing end of the bar* was cut off and replaced with new start- ing material. Following refining, the purest 20-in. section of the bar (obtained by discarding approximately 2 in. of the starting end and 8 in. of the finishing end of the bar) was leveled and then analyzed. The AIAG bar was 16 in. long and about 1.2 in. in diameter; it was purified by eight passes of a 2-in. zone at a rate of 1.6 in. per hr, the bar being contained in a sintered alumina boat lined with loose alumina powder of the highest purity. Data for the silicon and copper contents of the three refined bars are given in Table I. Derived data for the efficiencies of the zone-refining operations are listed in Table 11. It is clear from these two tables that the copper is removed much more efficiently—by a factor of 10 to 50 times—from aluminum during zone refining than is silicon. For example, in bar PG3 the thirty zone passes reduced the copper content from 10 to 0.02 ppm, i.e., by 500 times, whereas the same treatment lowered the silicon content by only a factor of about 16. It seem virtually certain, therefore, that the distribution co efficient, k, for silicon in aluminum is well above that for copper and is very likely not much below unity. This also implies that the solidus line on the aluminum-rich side of the A1-Si phase diagram is very probably appreciably curved near the aluminum melting point since the phase-diagram data indicate such curvature is unlikely in the liquidus.

Jan 1, 1965

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

Jan 1, 1920

By M. Metzger, J. Intrater

IN the large number of important studies on high-purity aluminum (e.g., recrystallization and grain growth, creep, internal friction), it does not seem to have been generally recognized that the iron content, despite its very low figure, has a strong influence on a number of properties. In part, its influence is due to the very low solubility of the Fe-A1 6 phase. For aluminum of about 99.99 pct purity, the iron content may be 0.001 to 0.004 pct. For values in this range, a second phase will be present below 410" to 480 °C. This was determined by extrapolation of a log solubility vs inverse temperature plot of the solid solubility data of Edgar.' One consequence is the inhibition of grain coarsening below the solubility limit. This is shown in Table I, which gives, for three iron contents, the annealing temperature required for the absence of grains smaller than 1/2 mm average diameter together with the minimum temperature for the presence of some grains larger than 2 mm diameter. The specimens were 1/4x 1 1/2-in. strips cut from hard-rolled 1/16-in. sheet supplied by the Aluminum Co. of America.

Jan 1, 1954

R. W. Raymond, New Pork City: It seems questionable to me whether Mr. Mezger's identification of the rock-structure he describes, as the Augengneiss of previous authors, is warranted by the definitions given by them. Naumann (1854)t describes Augengneiss as a porphyry-like variety, " which has assumed, by reason of single large kernels or granular concre-

Jan 1, 1896

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,' liquid mercury upon brass,4 and liquid mercury upon nickel.' Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.' Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962

By R. G. Gifkins

Mean boundary migration depended linearly upon creep extension under various conditions. Prolonged annealing or air-casting increased the proportion of immobile boundaries at a given stage of tests. Grain growth during annealing followed a power law. The linking of migration and sliding in creep and models for migration are examined; activation energies are calculated from these models. Segregation of oxygen to boundaries appears to be a controlling factor. THE idea that boundary migration and boundary sliding during creep are linked has often been suggested,'-5 especially when evidence has been obtained for an alternation between the two processes. In simple bicrystals sliding can occur without any migration6 but in more complex bicrystals7 it is observed. McLean' and Couling and Roberts 5 made measurements of both sliding and migration; McLean concluded that there was no linking of the two processes whereas Couling and Roberts supported the idea. McLean' also developed a model for migration during creep and annealing. The present work was initiated as part of a study of the recrystallization of lead during creep9 but has been extended to examine some aspects of the mechanism of migration. MATERIALS AND METHODS Specially refined high-purity lead* was used; the total of impurities, excluding oxygen, was 0.0008 wt pct. Oxygen was removed as far as possible by melting in vacuo, treating at 550" to 600°C with hydrogen and then casting at 450°C under a vacuum of 10-2 mm Hg; the oxygen was then believed to be 0.00005 wt pct. Specimens were made from extruded strip and then annealed at the required temperature in an air oven, controlled to 5 lac. They were then polished in a mixture of acetic acid and hydrogen peroxide. At this stage some specimens were etched to give grain contrast and their grain sizes determined by the intercept method. Migration of boundaries during creep was measured on the surface of polished (not etched) specimens, directly loaded at room temperature (22°C) or 50°C (52"C) to initial stresses of 300 to 700 1b per sq in. Twenty six vacuum-cast hydrogen-reduced specimens were used and, in addition, two specimens were from material air cast after hydrogen reduction ("partial" air cast) and two from air-cast material not treated with hydrogen ("full" air cast). Duplicates were made in the majority of tests. At intervals through the creep tests, specimens were unloaded and the migration measured, normal to the direction of migration at the point of measurement, for each boundary along standard traverses. Usually between 110 to 180 boundaries were measured at each of some twelve stages of the tests. Migration was measured on the projected image (X100) using prism illumination. Fig. 1 illustrates the method of measurement and shows the kind of variation of migration found from boundary to boundary and along particular boundaries. Fig. 2 gives an example of more extensive migration. The mean value of distance migrated was generally reproducible to *10 pct but occasional points gave a scatter of *20 pct. The correctibn applied by McLean8 to allow for the contribution sliding makes to the apparent distance of migration could not be used, for the sliding at most boundaries was too small to measure with the equipment available. There were two reasons for supposing the correction unnecessary in the present work;

Jan 1, 1960

By N. J. Grant, K. M. Zwilsky

A series of copper-alumina dispersion strengthened alloys were prepared using three different copper and two different alumina powder sizes. Improvements in strength of up to ten times that of pure copper were found in room-temperature as well as elevated-temperature stress-rupture tests. Conductivity values remained from 70 to 90 pct that of pure copper. The best alloys were based on the finest metal powder (1 p) and contained from 7.5 to 10-0 vol pet of 0.018 or 0,033 p alumina. DISPERSION strengthening of metals consists of strengthening a metal matrix by the addition of oxides or other refractory constituents, followed by strain hardening, in order to reinforce the base material and extend its temperature range of application. Since the discovery of SAP by lrmannl and Von zeerleder2 in 1949, many investigators have reported data obtained on a variety of metal-inert oxide alloys.3-7 The present work deals with the mechanical mixing of copper and alumina powders. While several techniques of introducing the second phase have been investigated to date, mechanical mixing so far has been recognized as the simplest, least expensive, and most universally applicable technique that can be used to obtain an ultrafine dispersion of inert particles. In the present case, the effects of changing the metal particle size, the oxide particle size and the volume percent of oxide were investigated. This work is an extension of a previous study.6 EXPERIMENTAL PROCEDURE The starting materials were three different grades of copper powder and two different alumina powders. The three metallic powders were -74 µ(- 200 mesh) electrolytic copper powder consisting of irregular equiaxed particles having a normal screen distribution and analyzing 99.5 pct Cu, and two powders having a 5-µ and 1-µ particle size, average, respectively. The latter powders were produced by the hydrogen reduction of purified sulfate solutions at elevated temperature and pressure and were furnished by the Sherritt Gordon Mines, Ltd. The alumina used was obtained from Godfrey L. Cabot Co., under the trade name of Alon C, one batch of powder having a particle size of 0.018 µ, the other a particle size of 0.033 µ. The crystal structure of these alumina powders was found to be cubic gamma. Each batch of powder was mixed in a Waring Blendor for a total of 15 min, followed by a low-temperature reduction in hydrogen and vacuum compacting in cylinders which were hydrostatically pressed at 35,000 psi to give a compact that could be handled conveniently. Six of the compacts were hydrogen sintered at 900°C while the remaining four were sintered at 1000°C. Subsequently, all compacts were hot extruded at 760°C with a reduction of area ratio of approximately 20 to 1. Evaluation of alloys included density and resistivity measurements, room-temperature tensile tests, stress-rupture tests at 450°C plus one other temperature per alloy, hardness tests, microstruc-tural examination, X-ray analysis of the dispersed phase after dissolving the metal phase, and oxidation studies on two of the alloys. A vacuum-melted, wrought copper rod was tested together with these alloys for comparison purposes. RESULTS Table I is a summary of the compositions, sintering temperatures, densities and conductivity values of the ten alloys prepared. All alumina additions are given in volume percent, and will be referred to as

Jan 1, 1962

By D. O. Hobson

Zirconium single crystals of various specific orientations were fabricated by rolling or drawing. The resulting textures were determined and are discussed with respect to the deformation modes that produced them. The crystals deformed in a predictable manner by combinations of up to third-order twinning with three twinning modes and by slip. Twinning was found to play a major role in initial texture formation. Texture changes produced by slip occurred only at the higher reductions. The twinning sequences that produced each intensity peak during the initial reductions could be identified. Schmid factor criteria were found useful in predicting which deformation modes to expect for each crystal orientation and fabrication procedure. The possible application of these data to poly-crystalline material is discussed. PREFERRED orientation or texture has a significant effect on the properties of most materials, causing anisotropy in fabricated cubic metals and enhancing the natural anisotropy of noncubic metals. This study evaluates the effects of several fabrication methods on the textures formed from specific starting orientations of zirconium single crystals and, it is hoped, gives an insight into the effects of the same operations on poly-crystalline material. BACKGROUND In fcc and bcc metals, texture changes take place by gradual lattice rotations caused by the operation of one or more slip systems. Deformation twinning plays an insignificant role in the deformation of such metals. In zirconium and its alloys, however, and in many other hep metals the ability to twin allows very rapid texture changes to be made with very small amounts of deformation. The deformation systems found in zirconium and its alloys are prism slip and three twinning modes.1 Slip occurs on the {1010}< 1120) system. There is little or no appreciable basal slip in zirconium. The twinning planes, illustrated in Fig. 1, are {1012}, {ll2l}, and {1122}. Two twinning modes, the {1012} and the {ll2l} operate for a tensile stress along the basal pole. A compressive stress parallel to the basal pole is required for {ll22} twinning. These twinning operations cause a 35- to 85-deg reorientation of the basal pole. The {1012} twin is the predominant tensile twin at room temperature. The twinning shears, S, are shown in the figure. A criterion for predicting which deformation system will operate when a grain is subjected to a known stress state is the Schmid (orientation) factor. This factor gives the fraction of the applied stress that computer program was written2 to calculate the Schmid factors for the four deformation modes in zirconium. It assumed three orthogonal stress axes and considered ninety-one different orientations of the basal pole in one octant of this stress space. At each basal pole position the Schmid factors were calculated for seven positions of rotation at 10-deg increments of the unit cell about the basal pole. Schmid factors were determined for a total of 637 orientations and for twenty-four deformation systems in each orientation. The program listed the Schmid factors for uniaxial stress parallel to each axis and, to approximate rolling, or-thonormal biaxial stress was also considered. Fig. 2 shows the range of orientations over which the various types of deformation would tend to predominate in biaxial plane strain with the stresses, equal magnitude. The exact boundary position between regions of different deformation modes depends, however, on the relative values of the critical shear stress for each deformation mode. Fig. 2 is drawn on the assumption that they are equal and it therefore may be only approximately correct. It is also recognized that the biaxial stress analysis may not be applicable in certain crystal orientations. EXPERIMENTAL PROCEDURE Single crystals of zone-refined zirconium, produced by Wilson of this Laboratory,3 were electrical-discharge-machined to form specimens for rolling, tube-drawing, and rod-drawing studies. Specimens were rolled at room temperature on 2-|--in.-diam hand-powered rolls from three different starting orientations: 1) the basal plane parallel to the rolling plane and the [1120] in the rolling direction, (0001)[ll20]; 2) the (1120) plane parallel to the rolling plane and the basal pole in the rolling direction, (1120)[0001]; and 3)_the (1120) plane parallel to the rolling plane and the [1100] in the rolling direction, (1120)[ll00]. Drawing specimens were cut with the [0001] direction as the drawing direction in the tube blank and [1120] as the drawing direction in the rod specimen. The drawing

Jan 1, 1969

The Arizona Committee, consisting of GERALD F. G. SHERMAN, Chairman, ARTHUR NOTMAN, Secretary, NORMAN CARMICHAEL, B. BRITTON GOTTSBERGER, W. L. CLARK, J. C. GREENWAY, W. G. MCBRIDE, FOREST RUTHERFORD, has arranged the following program for the Arizona Meeting, which has been approved by the President of the &apos;Institute and by the Executive Committee. It is printed herewith for the information of members, and probably will not be changed in any material respect. Monday, September 18, 1916.-Arrive at El Paso, Texas,, 6.30 A.M. Arrive at Deming, N. Mex., 9.30 A.M. Arrive at Chino, Ariz., 11.30 A.M., where luncheon will be served, after which there will be a visit to the Chino mines. From there the train will proceed to Hurley, N. Mex., where a visit will be made to the mill of the Chino Copper Co. Tuesday, September 19, 1916.-Arrive at Douglas, Ariz., at 8.00 A.M. The morning will be spent at the reduction works of the Copper Queen Consolidated Mining Co. "and of the Calumet & Arizona Mining Co. After luncheon a technical session will be held, with "Smelting" as a special subject for discussion. There will be a banquet in the evening, followed by another technical session or-a business meeting.

Jan 6, 1916

THE following employment items are made available to AIME members on a non-profit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th.St. New York 18; 100 Farnsworth Ave., Detroit; 57. Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to&apos; the proper key numbers in care of the New York office and include 6c in stamps for forwarding and. returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Mining Engineer, 41, married, one child, employed. Broad experience, both underground and open-pit, type mining. Exploration, development, exploitation, industrial construction, milling in northwestern United States. Desires position with progressive, established concern. M-666-259¬Chicago. Recent Graduate, 24, married, no children, B.S. mineral economics. Employed-one year&apos;s experience in development of deposits, study of problem areas. Will accept position anywhere in the world. Available immediately. M-667.

Jan 1, 1952

By C. A. Siebert, S. H. Bush

Isothermal temper-embrittlement studies were conducted on a 5140 steel at various temperatures for times as long as 3000 hr. Specimens from the embrittled steel were subjected to impact tests, metallographic examination, microhardness, and lattice-parameter measurements. SEVERAL of the steels in the low alloy group are subject to a pronounced decrease in impact energy if held within, or cooled slowly through, a range of temperatures below the lower critical. This phenomenon, known as temper embrittlement, is quite pronounced in the chromium steels of which AISI 5140 is typical. This study considered the response of one heat of 5140 steel when embrittled isothermally at various temperatures for times as long as 3000 hr. Excellent reviews of the work done in the field of temper embrittlement have been written by Hollomonl and Woodfine.&apos; Both authors list the various theories which have been advanced to explain temper embrittlement. Some of the mechanisms considered were: 1—a transformation below 700°C; 2—an allotropic modification of iron; 3—precipitation from the ferrite of such compounds as carbides, nitrides, phosphides, or chromium oxides; 4—decomposition of retained austenite; 5—modification of special carbides; 6—grain-boundary segregation; and 7—selective distribution of carbides. The present study investigated the changes in hardness, Meyer&apos;s number, impact properties, micro-structure, and lattice parameter which occurred on embrittlement. Previous studies considered the influence of microstructure and of prior austenitic grain size3 on the response of 5140 steel to temper embrittlement. Equipment and Procedure All samples were taken from one heat of 5140 steel; the chemical composition of this steel was: 0.43 pct C, 0.86 pct Mn, 0.020 pct P, 0.019 pct S, 0.27 pct Si, 0.84 pct Cr, 0.10 pct Ni, 0.06 pct Mo, 0.10 pct Cu, and the remainder Fe. The material was received as % in. rounds. This stock was cut down to blanks measuring approximately 0.425~0.425~2.196 in. Heat Treatment: The rough blanks were normalized at 1600°F (870°C) for 1 hr, then austenitized at 1600°F (870°C) for 1 1/2 hr, and quenched into an agitated oil bath. The specimens were tempered at 1275°F (690°C) for 5 hr and water quenched. These tempered specimens were designated as the toughened state. Embrittling Treatments: The tempered bars were divided into sets and subjected to the various embrittling treatments listed in Table I. Temperatures from 750" to 1050°F were investigated for times of 1 to 3000 hr. Special tests to determine the effect of heating a short time at a higher temperature after long-time embrittlement at some lower temperature were also conducted. All specimens were water quenched at the end of the embrittling cycle, then ground and notched to obtain standard Charpy V-notch specimens. Impact Tests: The bars were fractured in a 260 ft-lb Charpy impact unit; specimens were fractured at temperatures ranging from —315°F to room temperature. Fixed temperatures used consisted of —315°F with liquid nitrogen, —115°F with dry ice and acetone, and 32°F with ice and water. Intermediate temperatures were obtained by suspending the bars in a jig over the liquid nitrogen, dry ice and acetone, or ice and water.

Jan 1, 1955

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The a-p type alloys are subject to a loss of tensile ductility with increasing hydrogen content. No hydride phase is visible in embrittled a-B type alloys. The embrittlement encountered appeared to be of the strain-aging type. Both compositional and structural factors are shown to influence the hydrogen tolerance of a-B type alloys. IN previous papers by the authors, the effects of hydrogen on the structure and mechanical properties of high-purity and commercial-purity titanium were described. It was shown that the presence of hydrogen in these materials results in a hydride phase having low solubility at room temperature. This insoluble phase had little effect on the room temperature tensile properties, but did decrease the notch-bar toughness to a large degree. The binary Ti-H systemz indicates that hydrogen is much more soluble in £ than in a-titanium. Hence, it is not expected that the embrittling effects of hydrogen in a-fi alloys will be similar to that found in a alloys. Materials of this type studied in the present investigation included two commercial a-/3 alloys, Ti-8Mn and Ti-4A1-4Mn; three high-purity Ti-Mn alloys containing 3, 6, and 9 pct Mn; and four high-purity Ti-Mo alloys, Ti-SMo, Ti-10.9M0, Ti-13.1 M0, and Ti-20M0, of the a-B and B types. Materials and Fabrication—The high-purity base alloys, composed of iodide titanium and high-purity metals, were prepared by double arc melting under argon in a water-cooled copper crucible, using a water-cooled tungsten electrode. Radiographic examination showed homogeneous Ti-Mo alloys. The analyses of the alloys used in this investigation and their as-fabricated hydrogen content, where determined, are listed in Table I. The two commercial alloys were 1/2 and % in. diam bar stock. No analyses other than hydrogen content were made. In order to maintain the a-B relationship existing in the two commercial alloys, vacuum annealing and hydrogenation were carried out in the B field prior to final fabrication. Fabrication then was done by The three high-purity Ti-Mn alloys were forged to 3/4 in. diam rods at 1600°F, and hot swaged to 1/2 in. diam at 1380°F. Machined and degreased bar stock was vacuum annealed or hydrogenated, fabricated to 1/8 in. diam rod by hot swaging, annealed in argon for 1 hr at 1380°F !75O°C), and water quenched. The six yz lb Ti-Mo ingots were forged to Wi in. diam rods at 1600°F and then hot swaged to % in. diam. Machined and degreased specimens were vacuum annealed or hydrogenated in the /3 field, prior to fabrication, by swaging to Y4 in. rod at 1400°F. After fabrication, the 5 and 10.9 pct Mo alloys were annealed in argon for 16 hr at 1290°F and water quenched to give equiaxed a-B structures. The higher molybdenum content alloys were argon annealed 4 hr at 1470°F and water quenched to give all £ structures.

Jan 1, 1957

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE poor high-temperature oxidation resistance of the refractory metals becomes an important problem as higher operating temperatures are sought. A meaningful analysis of their oxidation behavior requires a knowledge of the phases that can appear during oxidation as well as their relative stability. Although several extensive investigations have been carried out to obtain this information for the W-0 system,1-10 serious inconsistencies still remain. First, the standard free energies of formation (AG°) determined in recent studies which used the solid electrolyte galvanic cell technique6,7,9 differ significantly from those obtained primarily from gas equilibration measurements.1,3,4,10 The disagreement is especially large for the highest oxides. These data have been used to predict the decomposition temperatures of WO2. 72 and WO2.90.1 A considerable extrapolation is required, resulting in a large uncertainty in the decomposition temperatures. Second, Bousquet and perachon3 have presented convincing evidence, ob- tained by gas equilibration measurements, in support of the long-contested existence of W30. Phillips and chang,ll on the other hand, were not able to observe this phase under similar experimental conditions. The purposes of this work, which is part of a continuing investigation of the W-Mo system, were to resolve the discrepancies between the AGO measured by gas equilibration and solid electrolyte galvanic cell techniques, to extend the latter measurements to lower temperatures, to redetermine the WO2.72 and WO2.90 decomposition temperatures, and to apply the more sensitive electromotive-force method to the question of the existence of W3O. I) EXPERIMENTAL PROCEDURE The measurement of ?G° of reaction by the use of calcia-stabilized zirconia solid electrolyte galvanic cells has been described previously.12 The method is based on the measurement of the difference in chemical potential of oxygen between an electrode containing the two oxides of interest and a reference electrode of known oxygen activity. Two different types of cell holders were used in this study. The first type of apparatus has been described earlier." It consisted of two solid electrodes separated by a disc of electrolyte. Both electrodes were exposed to the same stream of purified helium. With this design a gaseous transport of oxygen between the two electrodes is possible. The second type of apparatus, which has also been described earlier,14 effectively separated the two electrode atmospheres. It utilized a closed-end impervious, calcia-stabilized zirconia tube that was open to the atmosphere. The tube served as an electrolyte for the cell and provided a means for separating the anode compartment, which was held under a static vacuum, from an air reference cathode. The cells and reactions of interest are described in Table I. High-purity tungsten metal was obtained from the Fansteel Metallurgical Corp. and the Allied Chemical Corp. Table II contains an analysis of each material. WO3 was prepared by oxidizing the metal in air at approximately 600°C in high-purity recrystallized alumina boats and by the dehydration of reagent-grade tungstic acid in alundum boats. The two methods of preparing WO3 resulted in slightly different purities.

Jan 1, 1968

By W. C. Ellis, E. S. Greiner

WHEN metallic materials are deformed plastically, the process may be considered as one in which hardening and recovery occur simultaneously. The net hardening is that produced by deformation in the absence of recovery lessened by recovery during and immediately following deformation. Strain hardening takes place through movements of large groups of atoms acting to a degree as an entity. A complex microstress system is developed. Recovery is a diffusive-type process involving single atoms or, at most, only a few atoms in concerted action. This is accompanied by elastic strain relaxation. Recovery is strongly temperature-dependent. The driving energy for the process resides in thermal fluctuations of the atoms augmented by the energy of the stress field producing the deformation, and by that produced by the deformation. At very low temperatures recovery is essentially absent, or very small. At high temperatures in the hot working range, recovery is so rapid that deformation results in no appreciable net hardening. The interplay of strain-hardening and recovery results in differing end structures depending on the temperature and the strain rate of the process. For example, there is a prominent difference in the spacing of the slip markings and in the detail of X-ray diffraction patterns. High temperatures and slow strain rates favor a wide spacing of slip markings and sharp reflections.&apos;,&apos; This suggests that change in rate of the recovery concurrent with deformation modifies to a degree the manner of the deformation. Different slip systems may operate. For very slow rates, the mechanism may, as has been suggested, differ from that of "classical slip." In the experimental work that follows the findings will be interpreted from the point of view developed in this section. Recovery and Electrical Conductivity Electrical conductivity is a sensitive indicator of the state of strain in a material3&apos; * and was used in this investigation. The materials studied in wire form were: OFHC copper, a high purity (99.99 pct) and 2s grade aluminum, and grade A nickel. Wire annealed and initially 0.050 in. in diam was drawn through diamond dies in a simple holder maintained at 25", —75°, or — 195°C. Precautions were taken that for each material all conditions of drawing were the same except the temperature. Electrical resistivity was measured for each condition at 20°C. This was done as soon as practical after drawing to minimize possible room temperature recovery. The data for the four materials are plotted in Fig. 1 in terms of the change in resistivity for drawing at the several temperatures. The effect of temperature of drawing on the increase in resistivity is most pronounced for copper. Drawing at 25°C to 80 pct reduction in area increases the resistivity approximately 2 pct; drawing at —195°C to the same reduction increases the resistivity about 6 pct. The increase in resistivity" & in this metal is due to extra scattering of conduction electrons originating in the lack of orderly arrangement of the atoms induced by the deformation process. It has been suggested

Jan 1, 1953

[ASSETS CAPITAL ASSETS: Equity in United Engineering Society&apos;s Land and Buildings $486,792.79 Library 40,000.00 $526,792.79 INVESTMENTS: Jas. Douglas Fund-Schedule #2 $ 99,966.40 Life Membership Fund-Schedule #3 9,415.63 R. W. Hunt Medal Fund-Schedule #4 7,489.09 116,871.12 INVENTORIES: Paper Account 305.10] [ ]

Jan 1, 1925