Search Documents

By D. C. Seidel, E. F. Fitzhugh

The cementation of nickel from acidic solutions by metallic iron is discussed. The cementation is carried out in pressure vessels at temperatures above 100°C. The results from bench scale studies on variables such as retention time, temperature, and solution pH are presented. A continuous processing flowsheet is proposed. Cementation is one of the oldest known hydrometal-lurgical reactions. The cementation of copper on iron was recorded by 'Paracelsus the Great' in about 1500,1 and by 1600 the technique was being used to recover copper at the Rio Tinto operations in Spain.2 At least one early author felt that cementation may have been one of the primary reasons for the alchemists' belief in the transmutation of metals.' The early writings state that when iron was placed in the clear waters from some mountain springs, the iron disappears and copper is found in its place. To the alchemists this may well have been one of the most convincing proofs that transmutation could and did occur. Since these early times the recovery of copper from acidic solutions by cementation has been practiced in plants throughout the world. Probably the cementation technique in some form has been common to more copper mining and milling operations than any other single recovery process. During current hydrometallurgical extraction studies, which were sponsored by the Republic Steel Corp. at the Colorado School of Mines Research Foundation, Inc., it was found that under the proper conditions, metallic nickel could be cemented from acidic solutions by powdered iron. The reactions are apparently similar to those that occur during the cementation of copper, but the nickel cementation had not been anticipated because iron and nickel are nearly adjacent in the electromotive series. The potential difference between iron and copper is approximately 0.78 v, while the potential difference between iron and nickel is less than 0.21 v. The cementation of nickel with iron at room temperature is almost negligible, but when the reaction is carried out in a closed vessel at temperatures in excess of 100°C, the nickel can be cemented almost quantitatively. The part played by this discovery in a practical method of nickel recovery is set forth in a separate paper.3 The following paragraphs are a discussion of experimental studies that were made to investigate this cementation reaction. The technique has been designated the HTC or High Temperature Cementation procedure. The cementation work was part of a study on hydrometallurgical techniques for the extraction of nickel from the garnierite or silicate type nickel ores. A hydrothermal extraction procedure had been developed, and this technique produced an acidic pulp or solution that contained both nickel and appreciable amounts of magnesium.3 Small quantities of ferric and ferrous iron were also present along with cobalt, manganese, and chromium. The potential for recovering the nickel from these acidic solutions by ion exchange or solvent extraction did not appear to be promising because of the relatively high magnesium content. The Ni ++ and Mg++ have nearly identical ionic dimensions and tend to be co-absorbed or extracted during ion exchange or solvent extraction treatments. Preliminary tests indicated that the nickel could be precipitated as a sulfide when using the high pressure H2S precipitation technique developed for the Moa Bay operations of the Freeport Nickel CO.4 This technique gave good recoveries, but the nickel sulfide product requires considerable additional processing before a marketable form of nickel is realized. The process also requires clarified feed solutions, and the solids-liquid separations on the garnierite residues are difficult. A program was initiated to investigate alternate procedures that might shorten the route to a marketable nickel product, and hopefully also permit bypassing the difficult solids-liquid separation steps required for the H2S precipitation technique. It was during these studies that the nickel cementation reaction with iron was encountered. EXPERIMENTAL EQUIPMENT AND PROCEDURES The bench scale precipitation tests which were conducted during this experimental program were made in 2-liter stirred autoclaves.* A photograph showing the form and arrangement of the autoclave

Jan 1, 1968

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By T. A. Klinefelter, R. G. O’Meara, Glenn C. Truesdell, Richard W. Smith

THE investigation of domestic tales was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. I, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." HISTORY The use of steatite and talc in ceramic bodies goes back a great many years. If pure, tales shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a large business was carried on in the manufacture of tips for gas burners.1 With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Manchurian tales. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1943

By P. Stark, B. S. Lement

ACCORDING to Hanemann1 the hardness of retained austenite in a 1.7 pct C steel is increased by subsequent tempering. He reported that the hardness of this constituent increases only slightly on tempering to 300°F, rises more rapidly above this temperature, and attains the same value as the tempered martensite present in steel at approximately 480°F. The variation of hardness of both retained austenite and martensite with tempering temperature as obtained by Hanemann1 is shown in Fig. 1. Hanemann attributes the increase in hardness of the retained austenite essentially to continued formation of fine needles of martensite on tempering. Although he did not explain the actual mechanism involved, work hardening of retained austenite by the plastic deformation associated with such martensite formation appeared to be a possibility. Recently Lement, Averbach, and Cohen2 reported the existence of subgrains, about l000Å in diameter, in retained austenite and suggested that they may be delineated by a subboundary carbide. This raised the possibility that carbide precipitation might be responsible for the hardening reported by Hanemann. In view of these conflicting possibilities, an investigation" was carried out on a high purity, Fe-C alloy containing 1.7 pct C in order to clarify the nature of the phenomenon involved in the reported hardening of retained austenite. This investigation involved correlation of changes in microhardness and microstructure of the austenite as a result of tempering. Microhardness tests were made with a Tukon tester using a 25 gram load and a Vickers diamond. It was found that two groups of austenite hardness values were obtained after tempering at a series of temperatures up to 450°F, which was the highest temperature at which retained austenite regions could be identified microscopically. One group represents a high hardness level which in-

Jan 1, 1955

By H. W. Kerr, B. Soutiere

THE possibility of using unidirectionally solidified eutectic alloys as high-strength composite materials has been investigated by several workers. Unidirectionally solidified lamellar and fibrous eutectics have been shown to have good short-time structural stability at temperatures close to the eutectic melting temperature.'-4 Several investigations of both short-time high temperature tensile properties and creep properties of eutectic alloys have been carried out,3-" with promising results. Little work has been reported, however, on the thermal stability of eutectic alloys which have been unidirectionally solidified and subsequently deformed in compression. Since processes such as rolling and grinding introduce compressive stresses, and since the properties depend on the spacing and perfection of the composite structure10,11 this aspect is of definite importance if unidirectionally solidified eutectic alloys are to be considered for commercial use. A Cd-Zn alloy made from 99.999 pct starting materials was cast into a graphite boat and zone levelled12 to obtain a completely lamellar structure at one end of the bar. Sections from this region of the bar were removed, recast into 6.5 mm I.D. Pyrex tubing, and solidified unidirectionally upwards at a rate of 2.8 cm per hr. Specimens were cut from the solidified rods, heated in air at 200°C (0.88 of the eutectic melting temperature) for various lengths of time, and examined metal-lographically. Compression specimens were also cut from the solidified rod carefully machined to a length of & in., and deformed with the compressive axis parallel to the original growth axis to produce a total longitudinal strain of 12 pct. Some of these specimens were examined metallographically; others were heated in air at 200°C for various lengths of time and then examined. Metallographic examination of the deformed specimens showed the two types of deformation previously described; slip lines13 (smoothly bent lamellae) and kinks13,14 (sharply bent lamellae). Very close to the specimen ends there were a large number of deformation bands, but at a distance of about -re- in. the deformation was very localized, as shown in Fig. 1.

Jan 1, 1970

By B. A. Cheadle, K. P. Steward

Axial tensile, ring tensile, closed end burst, and free end burst tests were done at room tempe.vature and 300°C on three batches of Zircaloy-2 sheathing zuith different textures. Knoop hardness tests were also done on all batches. The mechanical properties of the tubes were largely dependent on the percentages of cold work, but were also markedly affected by the textures, particularly with respect to deformation behavio'r. The deformation behavior observed confirmed Picklesimer's predictions, zuhereas Knoop hardness results could be correlated with texture and yield strength anisotropy after the ,method of Wheeler and Ireland. From the mechanical properties, and from efjectiue strain values deterrlzined at the fractures using a photoqid technique, it zuas concluded that tubing witlz a single preferred orientation of radial basal poles best combines strength and ductility for any given deqee of cold work. THE mechanical properties required in collapsible Zircaloy-2 fuel sheathing for water-cooled power reactors are strength to resist wrinkling deformation by coolant pressure and ductility to accommodate a small amount of deformation in service without rupturing. Zircaloy-2 tubing during fabrication develops pre- ferred orientations of the a Zr grains due to aniso-tropic deformation behavior, and these textures markedly affect mechanical properties. Picklesimer' had predicted the deformation behavior of tubes with various textures, but the texture required to provide the optimum strength and ductility for a given degree of cold work has not been reported. To investigate this problem, tests at three transverse to axial stress ratios were done at room temperature and 300°C on three batches of Zircaloy-2 tubing covering a wide range of textures and percentages of residual cold work. Knoop hardness values were also measured to correlate with preferred orientation and yield strength anisotropy after the method of Wheeler and relland.' 1) MATERIAL For this investigation, three batches of tube-reduced tubing were chosen from the Zircaloy-2 sheathing produced for the Douglas Point Reactor. Individual tubes were 191/2 in. long, 0.600 in. OD, and 0.0165 in. nominal wall thickness. The identities of the batches, together with their textures, are shown in Table I. The tubes had the normal Zircaloy-2 composition3 of 1.5 wt pct Sn, 0.3 wt pct Fe, Ni, Cr combined with the following oxygen concentrations: Batch VII 1140 to 1390 ppm 0 Batch VIII 1400 to 1750 ppm 0 Batch IX 880 to 1320 ppm 0

Jan 1, 1968

By Carle R. Hayward

The growing importance of metallography has caused a corresponding interest in the improvement of apparatus for preparing specimens of metals and alloys for microscopic examination. The purpose of this paper is to describe an electric heating-furnace, a grinding- and polishing-machine, and a device for mounting specimens, which are used in the metallographical work at the Massachusetts Institute of Technology. These three pieces of apparatus were designed and made in the laboratory of the Institute, and each possesses some original features which may be of interest. Electric Heating-Furnace. The accurate control of heat necessary for metallographic work is best obtained by the electric-resistance furnace. Uufortunately, however, even the platinum-wound furnaces cleteriorate with use and ultimately burn out, while the cheaper resistance-materials are often short-lived. Since the resistance-coil must be replaced from time to time, it is of advantage to be able to make this change with as little trouble as possible, and this is an important feature in the furnace shown in Fig. 1. A is a cylindrical galvanized-iron can, with two handles, B. A porcelain tube, C, passes through the central hole in the cover of the can and rests upon the asbestos disk, D; the bottom of the tube is held in place by the asbestos ring, 3. The space, F, around the tube is filled with powdered magnesia. G is an ordinary assay-crucible, with the cover inverted so as to present a smooth top for supporting a second porcelain tube, H. The latter is wound with " Excello " resistance-tape, 0.014

Jan 1, 1912

By H. P. Leighly

WORNER1 briefly studied the embrittlement of titanium by mercury. He found that mercury will wet the titanium surface at 400°C in vacuo, if the specimen had been heated previously to 700°C to dissolve the oxide coating. Subsequent exposure to the atmosphere causes the mercury film to recede rapidly. Bending of the titanium specimen even after the mercury film has receded results in a brittle fracture. For the study of the embrittling effect of mercury on titanium, specimens 2 by 12 by 0.051 in. were cut from RC-130-A sheet, an alloy having a nominal 8 pct Mn content and a mixed a-ß structure. The specimens were stressed horizontally at a predetermined value after which a plastic ring having a cavity 1/2 in. diam by 1/2 in. deep was placed on the specimen. The cavity was filled with mercury and a hole was drilled in the specimen through the pool of mercury. If the stress level was high enough, fracture occurred instantaneously with the drilling. By repeating the test at different stress levels, the threshold stress can be determined. Mercury embrittlement causes a drastic reduction in the ultimate tensile strength of this alloy from 132,000 psi to about 15,700 psi. The drilling of the hole, in the absence of mercury, does not change the tensile properties. Fig. 1 shows the typical fractures observed as a result of the embrittlement of this alloy by mercury. The central portion of the fracture was brittle represented by the jagged region which appears to have occurred on the shear planes at about 45 deg to the stress axis. Ductile fracture, which is perpendicular to the stress axis, occurred near the specimen edges accompanied by a reduction of the specimen thickness. Examination of the fracture reveals that only in the brittle region does mercury wet the

Jan 1, 1962

By H. M. Merry

THE graphic methods and records described in this article have been developed, with satisfactory results, for the use of executives of the Chino Copper Co., in Hurley, N. Mex. Particular attention is directed to the use of large wall-charts, the quick reference display of large charts, the scale notation of metallurgical charts, the inclusion of mesh extraction on screen analysis diagrams. To properly comprehend the operation and metallurgical results from a concentrating plant, a daily record of essential data is kept, usually involving the dry weight of ore milled or treated, dry weight of concentrate or metal produced, assay values of heading, assay values of tailing, assay values of concentrate, and percentage of extraction or recovery. In addition it is often necessary to record moisture, pulp density, or dilution; percentage of weight of oils and reagents employed; screen analyses of grinding conditions, oversize, etc.; assay values of non-valuable or interfering substances; cost data; and such special information as may be required.

Jan 9, 1919

By Albert Hahn

ABOUT three years ago John Hays Hammond took over the control of the Eureka Metallurgical Co., at Salt Lake City, Utah. Funds were advanced for investigating the process invented by R. V. Smith, for concentrating oxidized lead ores. A great deal of laboratory work was done and a reagent was developed by C. M. Nokes of Salt Lake, which was found to be particularly suitable for oxidized copper ores, refractory manganese silver ores, and oxidized gold ores. After sufficient laboratory work had been performed to demonstrate the fundamental principles of these inventions, a test mill, having a capacity, of 20 tons of ore daily, was erected at Murray, Utah. In this test mill approximately 1200 tons of various types of ores have been concentrated by means of the above-mentioned process and reagents, and this large-scale work as well as laboratory work is being continued at present. Details of these mill tests are given in Table 1, and a representative group of laboratory tests are shown in Table 2. The process requires no special machinery or appara-tus. Its success depends entirely, on the method of preparing the pulp and its subsequent flotation in clean water, as outlined in the Smith patent. The reasons for the success of the Nokes special reagent are not definitely known. The outstanding feature, which seems to be of extreme importance, is that when the concentrates are examined under the microscope, each particle of mineral appears to have a particle of paraffin, attached to it. This paraffin-mineral combination seems to be particularly suitable for flotation and it follows that any coating oils readily attach themselves to the paraffin-mineral combination.

Jan 9, 1923

THE Institute assembled in Packer Hall of the Lehigh University, the President, Mr. David Thomas, of Catasauqua in the chair. Professor Henry Coppée, President of the Lehigh University, made an address of welcome to the Institute, and placed at its disposal a convenient hall for purposes of meeting. Mr. Thomas tendered his resignation as President of the Institute, as advancing years prevented him from actively participating in its meetings. The Institute declined to accept the resignation, and, on the assurance that active duties would not be expected of him, Mr. Thomas was induced to withdraw it. Invitations were received from Mr. B. C. Webster, President of the Lehigh Zinc Company, to visit the mines and works of the company; from Mr. Charles Brodhead, to visit the Chapman Slate Quarries; and from the Lehigh Coal and Navigation Company, to visit their works at Summit Hill and Mauch Chunk and the Nesquehoning Tunnel. The Council reported the names of persons already elected in the two classes of members and associates. The following resolutions were passed : Resolved, That a committee of three be appointed, who shall take into consideration the printing and publishing of papers originating with the Institute, and that a uniform system as regards size and execution be adopted. The committee appointed consisted of Messrs. R. W. Raymond, E. B. Coxe, and the Secretary. Resolved, That the Council design and prepare a seal for the Institute at the earliest practicable time. Resolved, That a committee of six, with power to add to its numbers, be appointed to examine into the question of the more economical production of iron in this country. The committee appointed consisted of Messrs. G. W. Maynard,

By Edward F. Winter, C. E. Ruoff

A silicon solid-state array image scanner is described. This paper deals with structural and performance properties of the array which basically consists of PIN photo and gating diodes, and low capacitance isolation diodes. Each chip of the array is composed of an 8 by 9 matrix of photo detector cells; each cell contains one each of the three diode types mentioned. This x-y matrix is read a column at a time with an access delay of approximately 100 nsec per column. It is designed to detect the presence or absence of illumination within 10-mil diam image spots located on a 15- by 15-mil grid. Radiant power level of an illuminated spot is low; of interest is the range around I uw with a of 8400g Structural improvements to the original array which will result THE purpose of this paper is to describe the results of a solid state scanner exploratory development activity. The scanner is intended to sense the presence or absence of low-level illumination falling upon a matrix of 10-mil wide squares arranged on a 15- by 15-mil x-y grid pattern. The light of interest has a wavelength of 8400, characteristic of radiation emitted from a GaAs lasing diode. This wavelength matches well the spectral absorption of silicon,' thus the well-developed silicon processing technology can be applied to fabricating large integrated arrays of PIN photocells to sense the radiation. The illumination state of the cells of the array is read, one column at a time, by addressing a drive line of the particular column in question and examining the state of those sense lines which are orthogonal to the drive Lines of in greater sensitivity at various wavelengths, both above and below 8400Å, and in greater speed are presented. These include variations in diffusion depth, resistivity of N and P regions, isolation techniques, and packaging. Trade-offs between access speed, cycle frequency, and sensitivity are discussed. A packaging approach to achieving an array composed of several chips is described. Requirements on this package are: 1) maintenance of 15- by 15-mil pitch of the light sensitive cell position, therefore positional accuracy of mounted 8 by 9 cell photo detector chips; 2) maintenance of inherent high array speed even though signal levels are low through high density close proximity mounting of monolithic sense amplifier circuitry. the array. One bank of N sense amplifiers is required, where N is the number of photodiode cells in each column of the array. CELL AND CHI" STRUCTURE A photograph of a single monolithic cell is shown in Fig. 1. Each cell is composed of three junctions, an isolation junction, a logic or blocking diode junction, and a photodiode junction; all of these junctions are connected electrically by a common N region. An electrical schematic of four cells of the array is shown in Fig. 2 with the associated driver and sense amplifier circuits in block diagram form. Note the common cathode configuration of the three diodes of each cell. Fig. 3, a diagram of the cell vertical struc ture, illustrates how the electrical configuration of

Jan 1, 1970

By W. A. Thomas

STEAM is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 lb., are used for power out of each ton produced.

Jan 9, 1921

By F. L. Toy, C. E. Sims

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By Alden B. Greninger

That metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc a1loys.l In all three of these alloy systems the martensite structures result from transformation of the metastable fi phase when the speed of cooling from the B range is sufficiently high to suppress decomposition into equilibrium phases. In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require rendjustments of concentration. For example, the martensite transformation in 60:40 (B) copper-zinc does not begin until the temperature has dropped to about minus 30" C., and then continues down to minus 130" C. and probably even at lower temperatures.' Furthermore, martensite processes apparently proceed only while the tempcrature is falling, within the proper range, and cease completely while the temperature is held constant ;$ and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of rnartensite processes by postulating that the mechanism 6I... consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By Alden B. Greninger

That metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc a1loys.l In all three of these alloy systems the martensite structures result from transformation of the metastable fi phase when the speed of cooling from the B range is sufficiently high to suppress decomposition into equilibrium phases. In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require rendjustments of concentration. For example, the martensite transformation in 60:40 (B) copper-zinc does not begin until the temperature has dropped to about minus 30" C., and then continues down to minus 130" C. and probably even at lower temperatures.' Furthermore, martensite processes apparently proceed only while the tempcrature is falling, within the proper range, and cease completely while the temperature is held constant ;$ and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of rnartensite processes by postulating that the mechanism 6I... consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By George W. Sheary

Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Company's Bethlehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with 3/4-in. slotted vibrating screens. The ore is washed and screened in the mill and the plus 1/4 in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30 in, cyclones, to 1% on 100 mesh and 65% minus 325 mesh. The ground ore is magnetically concentrated by three-drum permanent type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50 ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% plus 1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica.

Jan 5, 1962

By W. C. Meyer

In an effort to conserve and extend oil resources, the use of powdered coal-in-oil mixtures (COM) as an alternate fuel in oil-fired boilers is receiving increasing attention. For the approach to be successful, some degree of stability of the suspension against settling is needed. The variety of means available to achieve stability of this nonaqueous slurry is reviewed along with some of the physical and chemical concepts which underlie each method.

Jan 1, 1983

By New kensington P. A, W. L. Fink, H. R. Freche

The investigation of aluminum alloy systems prior to 1923 was severely handicapped by the low purity of the best aluminum available. However, by that time, the electrolytic purification of aluminum had been developed by the Aluminum Company of America,(1)† and in May, 1923, there was initiated, under the direction of E. H. Dix, Jr.,(2) a program for the investigation of the aluminum-alloy systems using the purest electrolytically refined aluminum. Up to the present time 15 papers (3) have been published, most of which are on the binary aluminum systems. Work is now in progress on the ternary systems, and it seems probable that most of the future work will be on ternary systems. Therefore this survey of the binary aluminum systems investigatcd up to the present time (the sixteenth paper of the series) concludes the first phase of this program. Certain qualitative relations between corresponding portions of the various binary diagrams as well as between different parts of the same diagram were noted some time ago by R. S. Archer.(4) In the present paper these relations and others are considered quantitatively by the application of well-known thermodynamic equations or by newly discovered empirical relations. No attempt will be made here to present the history of the development of the thermodynamic equations defining equilibrium or their application to metallic systems, although a list of references is given at the end of this paper for those who are interested in this phase of the subject. Two thermodynamic equations, which will be employed extensively in this paper, are: loge x1 = - L/RT + C

Jan 1, 1934