Search Documents

By W. E. Bruce, R. J. Morrell, James Paone

This chapter is a partial summary of an investigation by the U.S. Bureau of Mines (USBM) made in response to a recent request by the Assistant Secretary, Water and Power Development of the U.S. Department of the Interior, for a comprehensive review of horizontal boring technology related to underground power-line installation. This review is concerned primarily with 3 to 36-in. diam horizontal holes from several hundred to several thousand feet in length. An electric power system consists of three essential functions: generation, transmission, and distribution. The generation component includes the generating station and step-up substation; the transmission component includes the transmission line and stepdown substation at typical voltage levels ranging from 69 to 345 kv for underground lines and 69 to 500 kv for overhead transmission lines; the distribution component includes the distribution line carrying the commonly used voltages of 120, 208, and 240 v, the distribution transformer, and the line to the service customer.l The Federal Power Commission reports that 1600 miles of underground transmission lines of 60 to 345-kv capacity are now in service in the United States. By 1980, it is estimated that approximately 3000 miles of trans- mission lines will have to be placed underground.2 The cost of burying electric transmission lines underground in metropolitan areas, approximately 30 miles from the center of each of the most populated cities, will exceed $1.5 billion with the methods now available. The wide spread in unit costs of overhead and underground transmission lines narrows as right-of-way costs for overhead transmission in congested areas increase. Improved methods of underground emplacement will certainly reduce this difference in costs and even further favor underground emplacement. Also, in the future, overhead transmission lines will probably not be permitted in highly built-up areas.

Jan 1, 1970

By J. M. Karpinski, R. O. Tervo

A method and equipment have been developed for measuring the impact strength of grains of brittle materials. It is shown that brittle materials develop a characteristic particle size distribution when fractured by impact. A simple mathematical model has been found to describe this distribution, and one of the parameters of the model has been designated the r value. The r value is directly proportional to impact energy and, for fixed impact energy, it becomes a useful criterion of grain strength. Data are presented on the variation of the r value as a function of sample history, initial size, energy input and number of impacts. The results are interpreted in terms of the flaw theory of brittle fracture. The view is now widely held that brittle materials comprise a strong matrix, throughout which flaws or points of weakness are scattered at random. Failure always starts at one or more of these imperfections, and planes of fracture are established by the geometry of the flaw distribution. This view has been developed extensively by Weibull 1,2 and experiments of a confirmatory nature have been reported.3,4 Thus the process of fracture or size reduction of brittle materials can be regarded as a process of elimination or creation of flaws, and the concept of strength is intimately connected with the size and history of the specimen tested. One consequence of the point of view described above is that brittle materials will fracture to yield similar size distributions, although the impact energy to produce a given amount of fracture may vary greatly from one material to another. Generally speaking, experimental investigations of brittle fracture in solids have been confined to two extreme experimental situations. On one hand, we have tests on single specimens of well-defined, but artificial, geometry and, on the other, empirical data have been obtained on the feed-product relation in a variety of mills. The first situation necessitates specimen preparation, which in the case of brittle materials is equivalent to a priori size reduction, while the second one suffers from the disadvantage that little knowledge is gained about individual fracture events. Also, the statistical significance of single specimen tests may be questioned. Our approach lies somewhere between these two extremes. We test a large population of sized specimens and yet subject each specimen to a single fracture event. In 1956 G.H. Fetterley of Norton Co., Chippawa, Ont., made the empirical observation that product size distributions obtained from impacting sized grits can be described by the following equation where R is the proportion by weight of the grain that remains on a screen having an opening x on a side, x, is a parameter having the dimensions of length, and r is a number. This equation has since been derived on a theoretical basis by Gaudin and Meloy.5 They identify x, with the initial size of the test piece and r with the number of flaws per unit length. As will be shown below, our experiments indicate that both x, and r are functions of energy and hence they should more properly be called the effective initial size and the effective number of flaws respectively. Also, our empirical data give us no basis for assuming that r represents the effective number of flaws per unit length, rather than per unit volume. METHOD AND MATERIALS The impact test machine has been designed to feed specimens, essentially one at a time, into an evacuated chamber, where they fall freely and are struck with random orientation by one or the other of a pair of flat steel vanes. The vanes are mounted at opposite ends of a steel bar, which rotates at a closely controlled angular velocity about a vertical axis. Fig. 1 shows the flat circular vacuum chamber with the cover removed, and the horizontal steel bar with the steel vanes at the ends. The cylindrical pot in which the grains are collected after impact appears at the left. Fig. 2 shows the equipment assembled for a test. The vacuum chamber occupies the central position with the variable speed drive below the table surface, the vacuum pump at the extreme left

Jan 1, 1964

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York LOUIS D. HUNTOON, Chairman. ARTHUR S. DWIGHT, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. E. MALTBY SHIPP, Treasurer. GEORGE F. KUNZ. W. DE L. BENEDICT. Boston ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 4, 1914

By R. B. Moffitt

INTRODUCTION In recent times the continuing depletion of high grade mineral deposits and the massive increase in raw material consumption have forced the metal mining industry to exploit ore bodies of lower and lower grades. To obtain a satisfactory financial return from these deposits, there has been the concurrent and evident trend towards increasing the size of operations to obtain benefits from the economies of scale. The evaluation, planning, and design of these large scale open-pit operations, so as to yield the maximum possible return on investment, is an extremely complex, iterative procedure. With profit margins trimmed, "small" errors can become much more significant and with exploration costs spiralling, accurate and rapid evaluation is essential. It demands a sophistication and precision in the evaluation process unheard of ten years ago. What follows attempts to describe the need to thoroughly plan the overall evaluation programme such that duplication of effort is avoided and all relevant information is systematically recorded from the outset of exploration. The final section of the paper takes a realistic case study to illustrate the significance of pit slope angles on the design of the final pit and the economics of the total project. THE EVALUATION PROGRAMME The team, (for a team effort it must be), that is charged with the responsibility of conducting the evaluation exercise, has the difficult task of placing values on a multitude of independent and inter-related variables. Each variable has some economic significance; the degree of significance varying according to the metal sought, the environment in which it occurs, the vagaries of the market place, to name but a few of the problems facing the project team. From this maze of variables, the team must identify those that have the most critical influence on the overall economics of the proposed venture. Investigations must then be set in motion to quantify these controlling factors more precisely. It is important to recognize that such investigations form part of the evaluation programme and require monitoring for both timing and cost as the whole exercise of evaluating the project continues. To add to the difficulties, the economic significance of any particular variable may change during the course of the programme.

Jan 1, 1972

By J. McD. Porter

IN many of the old placer-mining districts are still to be found large tracts of gold-bearing gravel not suitable to be worked with a dredge, because the bed is too shallow- or the gulch too narrow. Frequently there is not enough grade to handle the gravel successfully by ground-sluicing or a bedrock flume, or it contains too many boulders to be worked successfully with the ordinary pipe or tube hydraulic elevator. In southwestern Oregon, two practical placer-miners named Ruble, after working for years trying to make money out of placer-ground containing many large boulders, invented and patented a hydraulic elevator of an entirely new type, and one . that has been found to work very successfully in flat' ground and in gravel containing many large boulders. It is a very simple contrivance. A few years ago I acquired the property near Pierce City, Idaho, known as the American placer-mine. Various attempts .bad been made to work this ground. A bed-rock flume had been installed by one company, an Evans elevator by another, and still other methods were tried on a smaller scale. All were unsuccessful. I installed a Ruble elevator, and it has proved very satisfactory. Working under 100-ft. (pipe) head, the 'ground has been handled at a cost of a little less than 8 cents per cubic yard. The conditions at the American mine are exceptionally hard, the boulders being large, heavy, and numerous. Basalt-boulders, up to a size of 16 by 18 by 32 in., have been elevated to a height of 16 or 17 ft., with a 4-in. nozzle-stream, under 100-ft. head. Boulders larger than this size are blasted. At the American mine, a foreman, two pipemen, and two laborers are-required per day of 24 hr. to operate the elevator. Several sizes of this elevator are in use, the one at the American mine being the 25-ft. size, having 25 ft. of grizzly

Oct 1, 1909

By C. D. King

DURING the 30-year period spanned by these annual Howe Memorial presentations, many lecturers could proudly claim a kinship either as a student or an associate of the man whose memory we honor. Although it has been my good fortune to have attended many of these annual lectures, it was not my privilege to have known Henry Marion Howe personally. However, his great repute as teacher and scientist was known to all undergraduates of my day and the later years have enhanced my appreciation of his wisdom and foresight. Those who knew him well have said he derived particular pleasure from speculations on the future world of metallurgy. For this reason, I feel that perhaps he would not be unsympathetic to a lecture in his honor which departs from the highly instructive scientific presentations made in the past by so many able Howe Memorial lecturers, and which is concerned more with the practical phases of various steelmak-ing processes and some speculations on their future form and relative importance. The word "revolutionary" is frequently applied to each seemingly important improvement in the production of steel ingots, but in retrospect these changes, impressive as they appear at the time, are merely steps of progress. In the hundred years from the inception of tonnage steelmaking, only three processes can be truly classified as revolutionary. They are the pneumatic process, known in this country as the bessemer process; the reverberatory method called the open hearth process; and, the electric furnace process. There have been many variations and combinations of the three fundamental methods, but they remain truly the only revolutionary methods in steelmaking since its early history. Everything else has been evolutionary, in effect. doing the same things that we have done in the past but doing them better, correcting our errors through experience, and slowly but inevitably reaching a higher state of accomplishment. It has often been said that coming events cast their shadows before, and the production of steel ingots is no exception. As a result of the unrelenting demands of World War I1 and the years that followed, truly impressive progress has been made in steel ingot production. The incessant pressure for immediate results during this period required the employment of initiative and daring, as in few past decades, and many developments were brought to fruition. Of equal importance is the possible effect on future steelmaking methods of the many ideas initiated but still in formative stages. Fig. 1 portrays ingot production in the United States by the three fundamental processes over a period of 75 years and is interesting because it poses some questions as to future trends. The early ascendancy of the bessemer, its replacement in importance by the open hearth process, the amazing growth of the latter, and the recent challenge of the electric furnace are evident from the chart. Management is fully aware of these changes, but is even more interested in the future trends. Our concepts of the relative importance of the more recent developments and their possible effect on future processes may perhaps be best exemplified by a specific, hypothetical problem. Let us assume management is contemplating a new ingot producing plant with an output of 100,000 net tons per month, located in an area where some purchased scrap may be obtained but where by far the largest component will be own-produced blast furnace iron. Management requires a process or combination of processes which will yield highly uniform quality characteristics in the ingot form, and represent the soundest selection in investment and operating cost. Under these conditions, the obvious selection for the past four decades has been the open hearth process but, in view of more recent developments, management may believe that it is no longer permissible to disregard other possibilities with impunity. Accordingly, to be assured of the best possible selection, they request that you review not only the possibilities of utilizing the conventional open hearth, duplex, bessemer, and electric furnace methods, but also the more recent developments, such as the turbo-hearth, the Linz-Donawitz method, the Perrin modifications, and other possibilities. With this background, one might then appraise the relative importance of these methods to meet a specific need, and concurrently speculate on the forms that future ingot processes will assume and the relative importance of these processes.

Jan 1, 1955

By David V. Ragone, James A. Craig, Richard E. Balzhiser

The Gibbs free energies of formation of UC2 and UC were measured by equilibrating two-phase mixtures of UC2 + C and UC, + UC with liquid bismuth. The measured equilibrium concentrations of uranium in the bismuth combined with available activity coefficient information yielded uranium activities in these two-phase regions. Measurements on UC2 were performed over the range 1015 to 1160 K and on UC over the range 1115° to 1165°K. The values obtained for UC2 are in excellent agveement with values determined using combustton calorimetry and low-temperature heat capacity measurements. The UC values are in fair agreement with the calorimetric values, differing by about 10 pct from the calorimetric determination. MUCH interest has been shown in the uranium carbides in recent years because of their potential as nuclear fuels. As nuclear reactor operating temperatures have been raised to increase thermal efficiency, new fuels have been required. The uranium carbides are of interest because of their high melting points, >2000°C, high thermal conductivity, and resistance to irradiation damage. The manufacture and use of uranium carbides are aided by a knowledge of their stability and reactivity under various conditions. In this regard the thermo-chemical properties of the carbides, i.e., heat capacity, heat of formation, free energy of formation, and so forth, are particularly important. A great amount of work has recently been done on the thermodynamics of the U-C system. Unfortunately, however, there has not been good agreement among the various investigations. This study of the free energies of formation of uranium monocarbide and uranium di-carbide in the temperature region 1100°-1200° K was undertaken to help clarify the situation. It should be noted that in the temperature range of this investigation, 1100°- 1200° K, the thermodynam-ically stable phase in equilibrium with graphite is U2C3, not UC2, Fig. 1. However, U2C3 is reported to be stable only under extremely low oxygen and nitrogen pressure. Although UC2 is metastable below 150O°C, it exists under most experimental conditions. It should also be noted that "UC," never exists as UC2 but with compositions near UC1.9. However, "UC2" will be used to designate the dicarbide phase except when the stoi-chiometry is necessary for clarity. METHOD The approach taken in this study of the free energies of formation of UC and UC2 was to determine the thermo- dynamic activities of uranium in the two-phase regions UC, + C and UC + UC, by equilibrating the two-phase mixtures with the liquid bismuth. When a mixture of solid UC2 + C is brought to equilibrium with liquid bismuth, the reaction that occurs is: Neither carbon nor UC, could be detected as dissolved material in the bismuth. The standard free energy for this reaction may be written: In the two-phase region UC, + C, Fig. 1, the thermo-dynamic activities of UC2 and carbon are unity. The activity of uranium in this region was determined by measuring the concentration of uranium in a liquid bismuth melt in equilibrium with the two-phase mixture. This concentration was then used in conjunction with the activity coefficient data of uranium in bismuth reported by Tien et al.' to determine the activity of uranium in the two-phase region, UC, + C. All of the quantities in Eq. [2] were then known, and the AG; (uc,) was evaluated. UC + UC2. For the studies involving UC + UC,, the reaction taking place when the two-phase mixture is brought to equilibrium with liquid bismuth is: The standard free-energy change for this reaction is given by:

Jan 1, 1969

By G. W. Mao, A. M. Gaudin, D. W. Fuerstenau

Activation of sphalerite with copper salts has long been thought of as a chemical reaction of the following form: ZnS + Cu++ [=] CuS + Zn++ [ 1 ] Early experimentation1-3 showed that the reaction seemed to be stopped by the coating of insoluble copper sulfide, but since the analytical methods were crude, it was only surmised that the reaction could proceed by diffusion. Probably the most conclusive evidence for reaction (Eq. 1) was obtained by Cooke,4 who found a stoichiometric replacement of Zn++ by Cu" after 50 days' reaction at about 100°C. Cooke also found the sphalerite to be covered with a rather thick coating of covellite, which in¬dicates that activation is a continuing replacement of Zn++ by Cu" rather than diffusion of Cu" throughout the sphalerite lattice. However, the occurrence of diffusion at high temperatures has been observed.5,6

Jan 4, 1959

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

By J. W. Richards

There are two essentially different 'types of case-hardening processes; that using a dry mixture in which the object to be case-hardened is packed and kept for the necessary time at the necessary temperature, and the "liquid" proccss, employing a bath of fused salts into which the object is immersed and which by immediate contact case-hardens the surface of the article. The Shimer process belongs to the second class, and was a war emergency invention. Of the liquid melts used as baths, the most effective and most frequently used are melted potassium cyanide and melted sodium cyanide. These may be used either pure or mixed with salts that reduce the melting point and the percentage of .cyanide present. The use of these baths since 1914 has met many commercial difficulties because of the high price and frequent commercial scarcity of the cyanide salts; at present sodium cyanide has practically entirely displaced potassium cyanide. Another trouble is the danger to the workmen handling the cyanide salts, which are extremely poisonous, and the annoying and poisonous vapors or gases given off in the workshop, unless an effective system of hoods and ventilation is provided, so as to prevent the gases from the baths mixing with the air of the room. Porter W. Shimer, of Easton, Pa., has invented a substitute1 for the bath of melted cyanides which case-hardens with equal or greater facility and effectiveness, gives off no poisonous vapors, and costs for chemicals materially less than the cyanide costs in the previously used baths. The process has been in use over a year in a large American works and the following statement embodies the results of practical experience in the use and operation of the process. The Shimer liquid or melted bath consists of a mixture of easily fusible salts that do not possess case-hardening properties, into which is immersed fresh calcium eyanamid, which imparts to the bath case-hardening properties. The composition of the non-case-hardening salts appears rather immaterial. Good results have been obtained by using a mixture of sodium chloride, calcium chloride, and barium chloride in equal proportions by weight; also a mixture of one part sodium chloride

Jan 1, 1920

By G. K. Dumbauld, B. E. Morgan

Kesults of laboratory investigations of the effects of drilling muds on oil well cements are presented which show that relatively large quantities of untreated muds do not seriously interfere with the setting of cement slurries, but that relalively small quantities of treated muds seriously retard the setting of cement slurries. Laboratory results also indicate that the harmful effects of contamination with treated muds can he counteracted by the addition of activated charcoal to cements. Also described is the successful use of cement containing activated charcoal for the placement of plugs in oPel hole after previous attempts with ordinary cement had been unsuccessful. INTRODUCTION The contamination of cement slurry by dilution with drilling mud has long been considered a cause of failure in oil well cementing. The cement slurry must displace the drilling mud from the annulus between the casing and the walls of the borehole. and it is probable that some mixing of the slurry and the mud occurs even under the most nearly ideal displacement conditions. Hole enlargement, failure to center the casing in the hole, and formation of gel structure in the drilling mud increase the probability of contamination. In some cementing operations, such as the placement of a cement plug in open hole, considerable mixing of the mud and slurry is likely. Many cement failures which can be attributed logically to no cause other than contamination of the cement slurry by the mud attest the need of a better understanding of this problem. Considerable attention was given to the problem of mud contamination of cements about 20 years ago.The effects of field mud upon cement slurries prepared with different amounts of mix water were investigated thoroughly, and the data obtained were invaluable in determining the causes of the high percentage of failure in oil-well cementing at that time and in bringing about improved cementing results. Since then, many aspects of the problem have changed, due primarily to advancements in cement and drilling mud technology. Today, several types of portland cement are used in well cementing and numerous chemical additives are used in drilling muds. An excellent report on the effects of drilling mud additives on oil-well cements was issued during 1951 by the American Petroleum Institute. Data in the report revealed that many mud additives, notably organic materials in relatively small amounts, produce a marked effect on the properties of cements. Prior to this time, little information has been available on the effects of chemicals commonly used in the treatment of drilling muds upon the properties of cements. Another aspect of the problem of mud contamination of cements, which has received no attention heretofore, is the possibility of producing a cement having properties unaffected by a reasonable amount of mud contamination. In view of the need for additional information on the contamination of present-day cements by currently-used drilling Muds, the investigation described herein was initiated Several years ago with a two-fold purpose: first, to determine the capacity of cement slurries to tolerate contamination by both untreated and treated muds without loss of ability to set and develop strength within a reasonable time; and, second, to investigate the possibility of enhancing the ability of cement slurries to withstand mud contamination by incorporating additives in the cement. The data for this study were obtained by mixing drilling mud with cement slurry and testing the resulting slurry-mud mixture for rate of set and development of strength. Also, several materials were tested for their possible improvement of the property of cement slurry to withstand mud contamination; these materials were tested in both contaminated and uncontaminated cement slurries.

Jan 1, 1952

Reno, Nevada. J A Fulton, Director For publications of either the Mackay School of Mines or the State Bureau of Mines, address the School of Mines at the given address. Except where the contrary is indicated in the following list, available publications are sent free From the Mackay School of Mines. Bulletin 1, The identification of Nevada's common minerals, 50 cents; 3, Notes on the ore deposits of Cave Valley mining district, Lincoln County, 4, A preliminary survey of the Scossa mining district, Pershing County, 5, Ore deposits of the Gold Circle mining district, Elko County, 6, Bedded deposits of manganese oxides near Las Vegas, 7, Spruce Mountain district, Elko County, and Cherry Creek (Egan Canyon) district, White Pine County From the State Bureau of Mines: Bulletin 1, Mineral resources of southern Nevada One volume: Mining districts and mineral resources of Nevada, by F C. Lincoln (1923), $1.50.

Jan 1, 1933

By F. A. Crossley

The titanium-rich end of the Ti-A1 system has been investigated up to 35 at. pct A1 (23 wt pet). One conzpound Ti3Al was found to occur between primary a and TiAl. It is ordered hcp with DO19 structure, it has virtually no solid-solubility range, and it has a closed maximum at about 875°C. OIL either side of the compound are a +Ti3Al two-phase fields. The limiting a1uminum solubility in primary a at the titanium-rich end is indicated to be 7.5 at. pct A1 (4.4 wt pet) at 550°C and about 6.8 at. pct Al fl wt pct) at 500°C. Quenching alloys from above the a + Ti3Al two-phase field produces the following structures with respect to alloy composition: Up to 13 at. pct A1 (7.8 wt pet), a solid solution; from 15 to 18 at. pct A1 (9 to 11 wt pct), shear transformation product or martensite; from 19 to approximately 30 at. pct (11 to 19 wt pet), submicro-scopic coherent Ti3Al in an a malvix. The twin hcp phase fields reported in the literature are the result of nonequilibrium corzdztions. Ti-A1 alloys, once partitioned by dwelling- in the a + ß phase field during either hot working or heat treatment, are extremely difjicult to homogenize at temperatures below 1000°C. Such partitioned alloys exhibit the characteristics or symptoms of two-phase materials, and may be said to suffer the "twin-phase syndrome". THE earliest investigations of the Ti-A1 system by Ogden et al.1 and Bumps et al.2 reported wide solubility of the primary solid solutions. Aluminum was reported soluble in the low-temperature allomorph to the extent of 37 at. pct (25 wt pct), and the first intermediate phase was reportedly TiA1. Somewhat later Kornilov et al.3 reported a similar diagram with phase boundaries displaced towards lower aluminum contents and higher temperatures. Beginning about this time (1956) reports in the literature made it very clear that one or more intermediate phases occurred at lower aluminum contents than TiAl.4-17 These reports included five major investigations of the titanium-rich end of the Ti-A1 diagram.4,12,14,16,17 Three of these diagrams show two two-phase fields below 37 at. pct Al, while two of them show a single two-phase field. The existence of the phase Ti3A1 is firmly established and is included in each of the diagrams, except one—that of Sato and Huang.12 The new phases are reportedly hcp and differ from primary a only slightly when disordered, and when ordered the "a" parameter is approximately one,4,12,15 two, 6-10,13,14 or four14 times that for primary a. Beyond this, however, the diagrams are remarkable for their lack of agreement. Two tacit assumptions are usually made in phase-diagram determinations of metal systems. These are: 1) equilibrium anneals bring the alloy to equilibrium or to indistinguishable closeness to it, and 2) equilibrium conditions established at elevated temperatures are either "frozen" by rapid quenching for evaluation at room temperature, or quench-transformation products are recognized as such. In the current investigation evidence was obtained that over substantial composition ranges neither of these two conditions was met in any of the more recent major investigations. I) MATERIALS, METHODS, AND TECHNIQUES The alloys of this investigation were prepared by nonc on sum able electrode arc melting. Materials used in the preparation of the alloys are summarized in Table I. The investigative tools employed were: optical and electron microscopy, differential thermal analysis (DTA), disatometry, X-ray diffraction, electron diffraction, and resistometry. Alloys for microscopic and X-ray investigations were prepared as 15-g melts. Alloys containing from 7 through 11 at. pct A1 were hot-rolled out of a furnace at 900°C, from 12 through 15 at. pct out of a furnace at 1000°C, and from 16 through 18 at. pct out of a furnace at 1125°C. Alloys containing more than 18 at. pct A1 could not be hot-rolled. The ingots were covered with Markal coating prior to hot rolling to minimize atmospheric contamination. After hot rolling, alloys containing up to 15 at. pct A1 were ground and pickled to remove 7 mils from each surface; alloys containing 16 and 18 at. pct A1 were skinned to a

Jan 1, 1967

By C. D. Williams, C. E. Ells

The susceptibility of quenched and aged Zr-2.5 wt pct Nb alloy to embritt2ement during irradiation has been examined for a number of solution temperatures and aging times. Material quenched from temperatures approximately 40°C below the transus has high tensile ductility, and this ductility is insensitive to aging at 500°C or to irradiation. If, however, the material is quenched from temperatures above the transus it becomes highly susceptible to loss of ductility either from aging at 500 or from irradiation. Inter granular failure is characteristic of the materials having low ductility. The distribution of the equilibrium phase is found to control the susceptibility to embrittlement by restricting 6 grain growth during heat treatment and thus influencing crack propagation. IN zirconium, as in titanium, -stabilizing alloy additions are used to obtain high strengths via quench and age heat treatments, and the Zr-2.5 pct Nb alloy has been developed1 because of its strength advantage over the Zircaloys. Early in the development of the Zr-2.5 pct Nb alloy the problem of 13 embrittlement was appreciated, and for this reason the solution temperature was chosen below the p transus.' In the course of irradiation studies on quenched and aged Zr-2.5 wt pct Nb alloy it was found' that irradiation introduced an important aspect of p embrittlement, riz., material quenched from the phase and aged 24 hr at 500°C was severely embrittled by moderate doses of neutron irradiation. This effect had not been studied in titanium alloys. In titanium the metallurgical features leading to 0 ernbrittlement were found to be structures with: a) coarse a platelets at the grain bondaries, b) finely dispersed a uniformly distributed throughout the (0) matrix,6 c) Widmanstatten a-13 with more than 50 pct P, d) the presence of some metastable p transformation products,3 and e) large prior -phase grain size.5 Alternatively, the presence of a uniform distribution of coarse a was conducive to high ductility and a structure largely of equiaxed a was very dctile. The detailed mechanisms of the embrittlement have not been worked out for all of these conditions, although weakness at either a-matrix boundaries or prior p grain boundaries have been prominent in the eculation. It was proposed that acicular a might act as a mild notch, and low ductility has been associated with easy fracture along its boundary.' There have been two opposing suggestions for the source of the high ductility associated with equiaxed a phase. JaffeeB proposed that this a would accept a large por- tion of the oxygen, thus increasing the ductility of the matrix, whereas after study of a Zr-Nb-Cu alloy Weinstein and oltz proposed that the a phase, softer than the martensitic matrix, acted to blunt cracks formed in the matrix. In the present work we have studied the effect of neutron irradiation on the ductility, particularly the P embrittlement, of the Zr-2.5 wt pct Nb alloy. By a variation of solution temperature and aging time a variety of metallurgical conditions have been examined, and a range of resultant ductilities obtained. The ductility has been related to the material microstructure and mode of fracture. EXPERIMENTAL The alloy used in the present work came from two separate ingots fabricated into rod of 3/8 or i in. diam, Table I. For both batches the P transus temperature was approximately 890° C. Most of the heat treatments were done directly on lengths of the j} in. diam rod, after which the tensile test specimens were machined. Quenching was achieved by dropping rods from a dynamic vacuum into water, the cooling rate estimated to be 2 100°C per sec. For aging the rods were encapsulated in evacuated silica tubes. Round tensile test specimens, with gage diam and length 0.160 and 1.0 in., respectively, were used throughout and pulled at room temperature or 300°C on Instron tensile machines, at a crosshead speed of 0.05 ipm. Specimens were irradiated in the NRX and NRU reactors, in facilities described in previous publications.'0 The metallurgical conditions examined have been: All tensile test specimens were machined with axes in the axial direction of the swaged rod. Although the specimen had a degree of preferred crystallo-graphic orientation with basal plane normals both parallel with and perpendicular to the tensile axis, the material was comparatively isotropic." The techniques of thin foil examination in the electron micro-

Jan 1, 1970

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.o.b. mines, the output in 1948 was 1,568,848 tons worth $19,756,738.

Jan 6, 1950

By J. H. Keeler

QUESTIONS raised during earlier investigations of the preferred orientation in titanium1 and zirco-nium sheet led to the examination of the rolling and annealing textures of beryllium and hafnium sheet. Since the c/a ratios are 1.568 and 1.584, less than that of ideal close packing, 1.633, it would be expected that the preferred orientations would be similar to those exhibited by zirconium and titanium. This was found to be true. However, in several regards the orientations observed for beryllium differed from those reported by Smigels-kas and Barrett4 and so are given here. The okientations for hafnium are presented since only the cold-rolling texture has been reported in the unclassified literature. The pole figures were determined by transmission using an X-ray spectrogoniometer with copper Ka radiation and the automatic pole-figure recorder designed by Geisler described previously.6 The intensity units in the pole figures in this case are only arbitrary since calibration against a random sample of the same material was not considered necessary for the original purpose of the examination. The beryllium sheet, cold-rolled from 0.036 in. to 0.006 in., a reduction of about 84 pct, exhibited a split texture with the [1010] direction in the rolling direction as shown in Fig. 1. The same specimen annealed in vacuo for 1 hr at 1000°C showed no change in orientation. These textures

Jan 1, 1959

By H. Buttner, F. H. Udin, J. Wulff

GRAIN boundaries, the interface between adjacent crystals differing only in respective orientation, have been the object of much experimental and moderate theoretical attention for many years. The earlier experimental work was primarily concerned with the effect that grain boundaries have on the physical behavior of metals, while the basic nature of the boundaries themselves drew only secondary attention. A complete turnabout has been witnessed in more recent years, however, as researchers are now undertaking investigations bearing as directly as possible on the character and physical properties of the grain boundary. Quite comprehensive reviews of the past literature on the subject of grain boundaries have been reported on numerous occasions by various authors, and together these references represent a thorough coverage.'-? It becomes evident in these reviews and other papers"" that the properties of grain boundaries can be explained by regarding a grain boundary as a crystalline region of transition between two unmatched grains. Studies show that grain boundaries have a definite interfacial energy. By measuring the geometry about a point where three interfaces meet in equilibrium, the energy of any two boundaries can be measured with respect to the third. If the absolute interfacial energy of one boundary is known, the absolute energy of the other two boundaries can be calculated. This apparently holds true for any system of phases and interfaces.""25 Most studies have been carried out on solid-solid or liquid-solid systems, or systems of both. However, if about the point of intersection one phase is vapor and the other two are disoriented grains, then two interfaces are surfaces, and one is a grain boundary. Investigations leading to relative grain boundary energy for this particular system have been made by Fullman,23 Greenough and King," and Bailey and Watkins." Herring" treats the system mathematically and arrives at an equation, which appears as Eq. 1, in a form consistent with the reference angles indicated in Fig. 1, ( d?1 ?n = x sina + cosa ( ------- 2 ?2 Sinß da + C0Sß (d?2/d As the system of interfaces comes to equilibrium, a groove of angle appears at the intersection of the grain boundary with the surface, an effect first observed by Rosenhain and Humfrey." Eq. 1 is essentially a summation of the vertical components in Fig. 1 set equal to zero, where ?1 and ?2 are surface tension vectors lying along the side of the groove at point 0 in the groove root. The differential vectors represent the forces tending to rotate the surface into a position that will expose a crystal cleavage surface of lowest energy. Chalmers, King, and Shuttleworth- simplify Eq. 1 by assuming the differential vectors equal to zero, ?1 = ?2= ?Surface and arrive at the following equation: ?B = 2?s cos [2] Greenough and King24 use Eq. 2 for determining the grain boundary energy of silver using prepared bi-crystals of known orientation. Bailey and Watkins25 have done the same for copper, as did Chalmers and others on lead. These authors report the grain boundary values as ratios relative to the surface energy. In the above work, the orientation of grains forming the grain boundary in all cases was controlled so

Jan 1, 1954

By R. I. Jaffee, F. C. Holden, H. R. Ogden

ECENT papers dealing with the properties of unalloyed iodide titanium have been directed primarily at the determination of base-line properties for alloy investigations. Early work was limited to a few tests because of the limited availability of iodide titanium at the time. In the results of papers by Campbell et al.,1 Gonser and Litton,2 Jaffee and Campbell,3 inlay and Snyder,4 and Jaffee, Ogden, and Maykuth, data on mechanical properties are presented for unalloyed iodide titanium in the annealed and cold-worked conditions. Data are presented in this paper which show the effects of heat treatment on the structure and mechanical properties of commercially produced iodide titanium. Correlation is made between microstruc-tural variables and the mechanical properties. Experimental Procedures Melting Stock: The melting stock used was as-deposited iodide titanium, produced by New Jersey Zinc Co. The furnished analysis showed the following range of impurities: N, 0.004 to 0.008 pct; Mn, 0.005 to 0.013; Fe, 0.0035 to 0.025; Al, 0.013 to 0.015; Mo, 0.0015; Pb, 0.0045 to 0.0065; Cu, 0.0015 to 0.002; Sn, 0.001 to 0.01; Mg, 0.0015 to 0.002; and Ni, 0.003. Hydrogen content as determined by vacuum-fusion analysis was 0.0091 wt pct (0.44 atomic pct) after arc melting and fabrication. Nitrogen analysis on the arc-melted and fabricated titanium showed a content of less than 0.002 pct N. The average hardness of the furnished stock was Rf 70, or approximately 85 VHN. Melting Procedure: The as-deposited rods were rolled, sheared, and degreased in preparation for arc melting. The charge was arc-melted with a tungsten electrode in a water-cooled copper crucible under a positive pressure of high purity (99.96 pct) argon. The final ingot was approximately 2 in. in diameter and showed no increase in hardness over that of the initial stock. Fabrication: Heating for fabrication was done in air. It was begun by forging the ingot into a 3/4 in. diam rod, at an initial temperature of 1600°F. Scale was removed by sandblasting. The rod was then swaged to 1/4 in. diam at room temperature through a series of 20 dies, with approximately 10 pct reduction in area between each die. An anneal of 1 hr at 850 °C in air was given after the 1/2 in. die, such that the final cold reduction was 75 pct. Sections cut from this rod were used for test and microstructure specimens. Heat Treatment: Heat treatments were carried out in resistance tube furnaces with stainless-steel linings, under an atmosphere of gettered argon. As further protection against contamination, the specimens were packed in titanium turnings in a titanium sleeve. Control experiments have shown negligible hardness increases with this method, indicating that contamination from oxygen and nitrogen is slight. Three cooling rates were employed in this work; these have been designated as water quenching, argon cooling (to simulate air cooling under a controlled atmosphere), and furnace cooling. The cooling rate for an argon cool is 100°C per min for the first minute, with an average cooling rate of 35°C per min over a 15-min period. A furnace cool requires about 10 hr, with an average cooling rate of 3.6oC per min during the first hour, and an average cooling rate of 1.2°C per min over the 10-hr period. Microimpact Test: The specimen adopted was based on the cylindrical Izod Type Y specimen (ASTM, E23-41T). All dimensions were reduced to half scale, including the notch radius. Specifications are shown in Fig. 1. The specimen is held vertically in an adapter and broken as a cantilever beam. Impact tests were run on a constant-velocity (11.34 ft per sec) Tinius Olsen impact testing machine with a total available energy of 100 in.-lb. Tests were made to determine the correlation between this microimpact and the standard V-notch Charpy impact test. Curves showing impact energy as a function of temperature for both impact tests are plotted in Fig. 2. Transition temperatures, when they occur, are about the same for both impact tests. All three titanium-rich materials have the same conversion factor, 10. Tensile Testing: Tensile tests were conducted on Baldwin-Southwark testing machines using the 600, 2400, or 3000 1b range. Specifications for the test specimen were taken from the 1948 edition of the ASM Metals Handbook, and are shown in Fig. 1. Strain measurements were made using an SR-4 resistance gage (Type A-7) cemented to the reduced section in conjunction with a lever-type extenso-meter. Readings on the SR-4 strain indicator were

Jan 1, 1954

By S. S. Marsden, S. H. Raza

An experimental study of the flow of line-textured. aqueous foams through Pyrex tubes is described. The foams range in quality F (ratio of gas volume to total volume) from 0.70 to 0.96 and behave like pseudoplastic fluids. At lower flow rates they exhibit laminar flow ad have apparent viscosities which increase with quality, and which cover a range of 15 cp to 255 poise for tubes of 0.25- to 1.50-mm radius rj. At higher flow rates a plug-like type of flow is developed, the extent of which increases with both T and ri. When the same foams flow through either open or packed Pyrex tubes, remarkably high streaming potentials ?E are often generated. These can easily reach 50v if nonionic foaming agents are used, but are at least an order of magnitude less for ionic foaming agents. A linear relationship between ?E and the pressure differential ?p is observed; this usually extrapolates to positive values of ?p at ?E of zero. The slope of the line increases with both F and ri. An equation was derived to describe the streaming potential of non- Newtonian fluids in circular tubes and was used to correlate experimental results. The calculated < potentials are of the right order of magnitude. INTRODUCTION Foams are both unusual and inniguing in their physical properties, and have been the subject of many scientific studies. However, present knowledge of foams is still fragmentary, specific and often contradictory. Apparent viscosity of foam is the physical property of greatest interest to both rheo1ogists and engineers. sibreel reported that the apparent viscosity decreased with increasing shear rate in a manner similar to some non-Newtonian fluids. Penny and Blackman2 reported that fire-fighting foams had both a limiting shear stress and a tensile yield stress. There is little doubt that some foams at least behave like non-Newtonian fluids, and have apparent viscosities considerably higher than those of either constituent phase. The high apparent viscosity of foam with its concomittant effect on mobility ratio and sweep efficiency no doubt prompted several attempts by research groups to use foam as a displacing agent in porous media. Based on recent experience, most of these groups probably succeeded in completely blocking fluid flow in the porous media and then abandoned their efforts. Two groups apparently found the successful combination of experimental parameters at about the same time.3,7 Others have recently added to our knowledge of foam flow in porous media and its use as a displacing agent.8-13 An experimental problem encountered by Fried3 was a transient blockage of foam flow in porous media when distilled water was used to prepare the foam-producing solution. Fried surmised that this was due to an electrokinetic effect and he eliminated it by using electrolytes in preparing foaming solutions. He also measured the streaming potential of a number of foams in capillary tubes which he found to be appreciably higher than those obtained when the constituent liquid flowed under comparable conditions. This paper presents results of a more comprehensive study of the streaming potential generated by aqueous foam flowing in both open and packed Pyrex tubes. It also adds to knowledge of the rheology of these foams as deduced from their flow behavior in open tubes. APPARATUS AND PROCEDURE A diagram of the apparatus used is shown in Fig. 1. Details of its construction, testing and use are described elsewhere.14 Careful selection of materials, extreme cleanliness and rather elaborate electrical insulation and shielding were necessary to obtain reproducible results (±5 percent). Both streaming potential and streaming current were measured with an electrometer. The design of the foam generator developed for this work is novel (Fig. 2). It will produce uniform fine-textured foams at pressures sufficiently