Search Documents

By Robert Mehl

THE system cadmium-mercury has attracted much attention, chiefly because of its importance in the study of electrochemical standard cells. The constitutional diagram, as it is accepted today, is essentially that FIG. 1.-BIJL'S DIAGRAM FOR CADMIUM-MERCURY ALLOYS. developed by Bijl1 (Fig. 1), though there has been a great amount of work done on the system by other workers.2 A year ago the senior author published a paper on the crystal structure of the system, in which were described determinations of crystal structure

Jan 1, 1929

By J. B. Newsom

In the Indiana limestone district, some 50 or 60 per cent of the merchantable stone in a quarry opening is waste, and only about 40 or 50 per cent of the stone from the opening is finally sold. So long as the present system of 'quarrying is used, the wastes measured and reported in this paper will continue. Comprehensive development of an entirely different method of quarrying, using wire saws for cutting, promises great improvement. Some of the savings to be expected are pointed out in the following pages. No attempt has been made to measure losses due to variations and natural flaws in the stone, since these vary greatly in different quarries, and accurate measurement would be difficult. The wastes that have been measured account for about 30 per cent of the total ledge, which leaves 20 or 30 per cent chargeable to unmeasured sources of loss. General Causes of Waste There are four general reasons for quarry waste: (1) the structure of the deposit, such as its shape, bedding planes, solution cavities and strain fractures; (2) efforts to quarry blocks which do not contain distinct color or textural variations; (3) the trade custom which permits purchasers to specify the size of the quarry blocks which they will buy, which is a matter of competition for business on the part of stone producers; (4) quarry methods, which cause the greatest amount of waste. Wide channeler cuts, hook holes, crooked splitting and uneven breaking on quarry floors are included in this category. Waste Due to Structure of Deposits The peculiarities of structure cannot be eliminated, but a chance for saving lies in quarrying to take advantage of them. The commercial deposits of Indiana limestone are lenticular masses from 20 to 70 ft. thick, and nearly horizontal. All of these deposits of good stone are in the Salem limestone, a bed in the sub-Carboniferous. The Salem is traversed by two systems of vertical fractures, a major system running from northeast to southwest and a minor system running from northwest to southeast. Where the stone is covered by an over-

Jan 1, 1932

By G. Sachs, G. Espey

IT is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.1-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.1-6, It has also been observed that higher stresses are set up by the use of wide-angle dies than by the use of acute dies.2 The actual stress distribution in drawn .tubing has been investigated by a few workers,7-9 but has not been related to the conditions of the drawing process: Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal.1-10 MATERIALS AND PREPARATION The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.‡ This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2 -in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during sinking, as previously observed 4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation method1,11 of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring on splitting. For the determination of the complete stress

Jan 1, 1941

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By O. B. Bennett

WHEN diamond drilling was introduced in the Rhokana mines in 1939 it was used principally for pillar removal and for completion of the upper portions of shrinkage stopes which were being affected by increasing pressure. This method of drilling long blastholes proved so successful that it was extended gradually to cover stoping, pillar recovery, and hanging cave work. BY 1949 virtually all the ~roduction of Mindola and Nkana was being obtained by this method. At the present time 87,500 ft are drilled each month by the 80 diamond drills in daily operation. Responsibility for control and issue of diamond drilling equipment and crowns, as well as tabulation of all performance figures, was taken over by a sPecially formed Roto drill department, which also investigated the problems encountered with this new method. To assist this department a fully equipped test chamber, Fig. 1, was established underground where performances of various types of machines and equipment could be studied under conditions as nearly uniform as possible. Since the establishment of this department, which was eventually taken over and incorporated into the study department, considerable experimental work has been done on every aspect of the subject. The problems can be classified broadly under four headings: improvement of drilling equipment, crown design, machines, and stoping layouts. One of the major problems with drilling equipment has been to eliminate vibration. Owing to flexing of rods in the hole, severe friction is set up on the back end of the 'Ore barrel and On any high spots in the rods, inducing harmonic vibration in the string of rods and causing the crown to chatter against the face. This not only causes premature crown failure but also reduces penetration speeds and increases wear on the machines and rods used. In the early days, when only holes of EX size were drilled, vibration was largely overcome by periodic greasing of rods and core barrel during each run, but with the change-over to the larger BX hole it became obvious that application of grease by hand was inefficient and time-consuming, and attempts were made to perfect a self-lubricating core barrel. A series of these core barrels was made up and tested and a number of the latest type were used under normal operating conditions, but although footages up to 120 ft were drilled without refilling the overall performance was inconsistent, and the idea was shelved in view of the success of the stabilizer rods referred to later in this paper. At the same time tests were made with barrels 5 ft and later 6 ft long instead of the normal 2 ft. Although a slight improvement was noticed, greasing was still necessary. It was found that rod vibration increased as the core barrel became worn, and in an early test chamber experiment crowns drilled with a worn core barrel averaged 95 ft with a diamond loss of 4.76 carats, whereas the same type of crowns with a new barrel averaged 228 ft with a diamond loss of 3.13 carats. until then all BX drilling had been done with B-sized rods, but during a test on a string of BX-sized rods it was noticed that vibration was negligible. Because of the larger surface area of metal bearing on the sides of the hole, however, the friction and resistance of rods of this size rendered them impracticable on any but the most powerful of the machines, The use of stabilizers spaced evenly along the rods was the next logical step, and for this B couplings, see Fig. 2, were set with three tungsten carbide inserts 1 in. long placed around the periphery equidistantly and at an angle of 45" with a right hand lead. These were placed immediately behind the core barrel and then at 12-ft intervals, as it was found that vibration still occurred when the stabilizers were more than 15 ft apart. The effect of these stabilizers was immediately noticeable; holes were drilled with a minimum of vibration, penetration speeds were improved, and as it was no longer necessary to grease the rods there was a marked decrease in the overall drilling time for each hole. While tests were being made with the stabilizer comeb periodic were taking place with a set of tapered threaded rods, and because there was marked improvement in efficiency it was decided to incorporate the stabilizers and tapered threading in all new rods ordered for Rhokana. The feature of these rods is that only four full turns are required to tighten the coupling as against nine for the present type of B rods. Also, as they are self-centering it is virtually impossible to crossthread them. Each rod has a male 5" tapered Acme thread, Fig, 3, on one end and a female at the other, so that separate couplings are unnecessary, and every fifth rod has an

Jan 1, 1955

By A. L. Mincher, W. F. Sheely

Mechanical properties of columbium have been studied over the temperature range of -196 to 1093oC. The decreased strengthening influence of cold-work at temperatures below ambient has been interpreted in terms of the Peierls-Nabarro effect. Maxima in the rate of strain hardening observed during tensile testing in the range 250-600°C. have been correlated with interstitial impurities to indicate the temperature ranges at which carbon, oxygen, and nitrogen, respectively, are responsible for strain aging. THE growing need for structural materials for use above the useful service temperatures of the iron-, nickel-, or cobalt-base alloys has caused the refractory metals to be considered as potential engineering materials. These metals, which include columbium, tantalum, molybdenum, and tungsten, are called refractory because the lowest melting point among them,that of columbium, is about 1000°C higher than the average melting temperatures of conventional high-temperature alloys. They are all body-centered cubic transition metals and, as such, their mechanical properties have basic characteristics which distinguish them from the face-centered cubic metals. For example, all show a much steeper rise in strength with decreasing temperature below room temperature than do the face-centered cubic metals, and their mechanical properties are strongly influenced by interstitially dissolved impurities. In order that these new metals may be used efficiently, it is necessary that their characteristics of behavior be fully known. In this paper, the mechanical properties of columbium will be examined over a wide range of temperatures. In particular, the influences of cold-work and individual species of interstitial impurity atoms on mechanical properties will be described, and basic mechanisms which may control the observed characteristics will be explored. EXPERIMENTAL The material used in this investigation was Union Carbide Metals Co. columbium roundels consolidated to four 4-in. diam ingots, three by consumable-electrode arc melting and one ingot by electron beam melting. Impurity contents of the ingots and methods of ingot conversion and treatment are summarized in Table I. The only metallic impurity occurring in any significant quantity was tantalum at about 0.1 pct. Iron, silicon, titanium, and zirconium were each less than 0.015 pct; boron was 1 ppm or less. This should have no appreciable influence on properties. The electron beam melted material, being the purest, will be used as the basis for comparison in the discussions to follow. Tensile tests were conducted from-196 to 1093oC, on both cold-worked and fully recrystallized arc-melted and electron-beam melted columbium using standard 1/4-in. diam, 1-in. long gage length test specimens. A strain-rate of 0.005 in. per in. per min was employed until the 0.2 pct yield strength was achieved and then the strain-rate was increased to 0.05 in. per in. per min for the balance of the test. Samples were protected in an inert atmosphere at tests above 300°C. The tensile properties obtained on the electron-beam melted columbium, E, in both the cold-swaged and recrystallized conditions are given in Fig. 1. The yield strength data of Dyson, et al.,' obtained on recrystallized electron beam melted columbium and the tensile strength data reported by Tottle2 on powder metallurgy columbium are included in Fig. 1. The material used by Tottle had been purified by vacuum sintering. There is excellent agreement between Dyson's data and those obtained in the present investigation. The tensile strengths obtained by Tottle were slightly greater than those obtained in this investigation on electron-beam melted columbium but varied with temperature in a similar manner. Tottle's data showed a maximum in tensile strength near 500°C, as did our data on electron-beam melted material, and also showed a small maximum at 300°C. The significance of these maxima will become evident later in the discussion. The tensile properties of cold-swaged and recrys-tallized arc melted columbium are plotted in Fig. 2. It was found that the properties of the recrystallized arc-melted columbium from all three heats showed very close agreement except at temperatures between about 500" and 800°C. A reason for this range of disagreement will be suggested in the discussion. The generally good agreement, however, attests to the ability of cold-working and subsequent recrystal-lization to erase the effects of the three different primary breakdown procedures and to produce nearly equivalent structures in the samples derived from the three different heats. wesse13 reported tensile data on columbium having interstitial impurity contents between those of the

Jan 1, 1962

By J. A. Herbst, D. W. Fuerstenau

The effect of mill speed and ball load on the dry ball milling of dolomite is examined in the context of the batch grinding model. Observed changes in the parameters of the model are interpreted, as far as possible, in terms of the mechanics of particle motion in the mill. A parameter estimation scheme previously proposed by the authors is shown to provide the basis for a successful simulation of grinding behavior over a wide range of mill speeds and ball loads. Finally, a combination of experimental and simulated results is used to determine the optimum mill speedball load for closed circuit grinding in this mill-material system.

Jan 1, 1973

By P. Greenfield, C. C. Smith, A. M. Taylor

The Mg-Zr alloy ZA and Mg-Mn alloy AM503(S) are shown to have a markedly improved resistance to creep deformation after suitable heat treatments. This improvement makes them suitable for certain stress-bearing fuel element components in nuclear reactors. The extent of strengthening is described and an explanation of the behavior of both materials is given, based on a combination of strain-aging and grain growth. The increase in operating temperatures of fuel element components in Calder Hall type nuclear reactors has necessitated the development of magnesium base alloys with a very high resistance to creep at temperatures up to 500°C. Such alloys are not required for fuel element cans, which require high-creep ductility rather than strength, but for can supporting and stabilizing components, which are needed to support the imposed loads without deforming more than about 1 pct in times of up to 40,000 hr. The amount and type of alloying addition made to magnesium for these parts is limited by the necessity of keeping the cross-section to thermal neutrons as low as possible. The alloys must also possess a high resistance to oxidation in CO2. Alloys which have been developed for this application include ZA, an alloy of magnesium with 0.5 to 0.7 pct Zr and AM503(S), an alloy of magnesium with 0.5 to 0.75 pct Mn. In the as-extruded condition these alloys are very weak and ductile in creep but it has been found that they can be strengthened to a significant extent by heat treatment. This paper describes the method of developing a high-creep resistance in ZA and AM503(S), the extent of the strengthening produced and discusses the probable mechanisms of strengthening. TEST MATERIALS Specimens were taken from typical casts of ZA and AM503(S) alloys extruded into 2 1/4-in.-diam bars, supplied by Magnesium Elektron Ltd. Typical analyses of the bars were as follows: The as-extruded mean grain diameter was 0.001 to 0.002 in. for the ZA alloy and 0.003 in. for the AM503(S) alloy. EXPERIMENTAL METHODS Extruded bars of ZA alloy, 2 1/4 in. in diameter and 9 in. long, were heat treated in electrical resistance furnaces in an atmosphere of flowing CO2 containing 50 to 300 ppm water, thereby reducing the extent of oxidation compared with that which would have occurred in air. Heat treatments were carried out at 600oc for times of 8, 24, 48, 72, and 96 hr and material was subsequently both furnace cooled and water quenched. In order to measure the effect of time of heat treatment, specimens were creep tested at 400°C and 336 psi for about 1000 hr. Subsequently, the behavior of material heat treated for 96 hr at 600°C and furnace cooled was tested at a variety of stresses from 200° to 500°C. Tests were also conducted at 200o and 400°C on material in the as-extruded condition for comparative purposes. With the AM503(S) alloy, only the effect of heat treatment at 565°C for 4 hr was examined. It has been shown1 that such a heat treatment produces marked strengthening in this alloy. Tests on this material were conducted at a variety of stresses at 200°, 300°, and 400oc with comparative tests on as-extruded material at 200o and 400°C. The creep tests were carried out on machines using dead-weight loading and direct micrometer strain measurements on specimens 5 in. long and 0.357 in. diameter. At temperatures of 400° C and below, the creep tests were conducted in air, but at higher temperatures an atmosphere of CO2 was used. Grain size measurements were made on ZA in the extruded and heat treated states and on each specimen after creep testing. This was done by a line count of a minimum of 20 grains in two or three random fields in the longitudinal and transverse directions. The same method was used for measuring the grain size of as-extruded AM503(S), but the grain size of the heat treated material was so large that this method could not be employed. For heat-treated AM503(S) the large grained characteristics (between 0.1 and 1 in.) were confirmed by the measurement of individual grains. In the case of the ZA alloy, specimens taken from various stages in the program were analysed for hydrogen by a combustion method. Material in various states was also analysed for the soluble and insoluble zirconium content by dissolving in dilute hydrochloric acid. This technique has been useda for the determination of amounts of zirconium present

Jan 1, 1962

By John Gross

The group of claims, comprising over 1,100 acres, located at Maitland (formerly known as Garden City), in the Ida Gray mining district, Lawrence county, South Dakota, are now being developed and operated by Alexander Maitland, the owner. Prior to the acquisition of this property two years ago by Mr. Maitland, but little work had been done in this district, and little was known of the extent of the ore-deposits. Recent development, however, has opened up some very promising ore-shoots. The ores so far encountered are the so-called " Potsdam siliceous ores," occurring in the flat formation lying immediately above the Cambrian quartzite, which dips at this locality about 12º. Both oxidized and blue ores are found, and the latter have proven particularly refractory to treat. No prospecting in the underlying slates of the Archean period has so far been attempted; but this work is one of the future considerations in the development of the property. Small quantities of blue ores are unavoidably sent to the mill, but special care is taken to send only the oxidized ores for the cyanide treatment. The ores, being close-grained and hard, have given considerable trouble in their treatment. Pyrrhotite arid pyrite exist in about equal proportions; arsenic, copper, and traces of antimony and tellurium are encountered, and considerable quantities of bismuth have been found in the zinc-box precipitates. The silver in the low-grade ores is slightly greater than the gold, while in the high-grade ores the reverse is generally true. Table I., showing the variations in the analyses of these ores, gives a fair idea of their general character. Early in 1902, the building of a 40-stamp wet-crushing cyanide-mill was begun, and it was finally placed in commission

Jan 1, 1905

By H. Kazemi

A pressure fall-off test on the injection well of a forward combustion project may permit us to calculate the distance to the burning front. In the mathematical description and analysis of test data, we have considered the effect of temperature on the thermodynamic properties of reservoir fluids. The temperature distribution predicted by Chu' for a combustion wave has been used in analyzing a field test. Numerical solutions were obtained by simultaneous solution of the flow equation, the continuity quation and the equation of state. Although this analysis conccntrated on isotropic systems, the results can be extended to systems having directional permeability. INTRODUCTION Conventional pressure fall-off tests have been used extensively to determine reservoir characteristics in gas- or water-injection projects.- such tests consist of injecting fluid into the formation at a constant rate until steady state is nearly achieved, then discontinuing injection and measuring the bottom-hole pressure as a function of time. A plot of pressure vs the logarithm of time (measured from the instant of shut-in) yields a smooth curve characterized by three distinct regions (Fig. 1): Region I reflects the permeability alterations in the vicinity of the wellbore; Region II reflects the reservoir characteristics further away from the wellbore; and Region 111, the characteristics in the displaced fluid bank. The curves in Regions II and III are straight lines! the slopes of which are proportional to the reciprocal of the flow capacity of the formation behind and ahead of the interface as shown by Eq. 1, respectively:

Jan 1, 1967

By VILLIAN BRADEN

THIS paper is presented in the hope that it will be instructive in view of the future large expansion of the mining industry in the west-coast countries of South America. There is a more or less general impression that the Spanish-American workman is inferior to the American, but after some years of experience and observation I doubt the correctness of this view. Taking into consideration all the elements which make for efficiency of labor, it has been found, particularly in Chile, that under proper organization native labor yields as much, man for man, and more, dollar for dollar, than in the Western United States. If a manager is willing to accept unreservedly the c costumbres del pais, without combating intelligently and patiently the ones tending to inefficiency, he should expect no better results than he deserves. He must conscientiously insist that a " square deal " be given and exacted; that liquor be excluded from camp as far as possible; that comfortable quarters and other uplifting elements of life be provided; and that the costumbres del pais shall not be over-ridden roughshod. He should also insist upon the gradual and reasonable adjustment of these conditions to the exigencies of the work; and (by no means the least difficult of his tasks) he should select the most competent men to patiently direct and teach the natives in the several departments, and by their own example encourage self-respect and decency. While the Braden mine is by no means as yet operated on a large scale, according to modern rating, it will nevertheless be interesting to note what has actually been accomplished there. An illustrative description of the mines and mill of the\

Oct 1, 1909

By E. F. Bailey, L. S. Birks

The effect of stress on the austenite to ferrite transformation in carbon steel was studied by X-ray diffraction techniques. Tensile stress was found to cause reorienta-tion of austenite above the transformation temperature, to accelerate equilibrium conditions at the transformation temperature, and to cause precipitation of large carbides at a critical value of stress. IN the past, a number of papers' have discussed the effect of stress on the austenite to martensite transformation at relatively low temperatures. In general, it has been shown that tensile stress induces some transformation at a given temperature, while compressive stress retards the transformation. Very little work has been reported on the effect of stress on the transformation from austenite to ferrite plus carbide near the A, point in steel. One of the few papers in the literature2 reports an increase in A1 of about 1°C in pearlitic steel upon the application of tensile stress. In this paper, the effect of tensile stress on eutec-toid steel at, and above, the A, point was studied in

Jan 1, 1956

By E. F. Kingsbury

ONE of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consumption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. SUBSTITUTES FOR PLATINUM During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data-at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is , even more so to the electrical engineer and it is surprising that the literature records no systematic and comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a Standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper materials, and the other, the development of materials of superior electrical performance. The merit of a contact metal has been assumed to be dependent on its infusibility, and since the more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were

Jan 1, 1928

By E. A. Anderson

In another paper' the writer has shown that the low permissible maximum fiber stress in a loaded zinc sheet demands a much closer support spacing than is used for steel. The limiting fiber stress in 13-gage (0.032 in.) sheets having a 1-in. depth of corrugation was found to be about 5000 lb. per sq. in. on a 37-in. span under a load of 40 Ib. per sq. ft. Corrugated steel sheets are commonly laid with spans varying from 48 to 60 in. In order to increase the span in 13-gage zinc to 54 in. (a common spacing) the metal must be capable of withstanding, under long-continued loading, a maximum fiber stress of about 10,000 lb. per sq. in. This is known to be impossible with unalloyed zinc. In this paper the writer describes a series of experiments leading up to the development of an alloy capable of safely sustaining this fiber stress. The effect of alloying on the slow creep of zinc was studied by means of static tensile tests, accurate determinations of apparent elastic limits and finally by means of loading tests on full-size roof sections. Two industrial buildings roofed with alloyed zinc sheets on spans involving fiber stresses in excess of 10,000 lb. per sq. in. have been under observation for over two years without signs of sagging. Experimental Work Two methods of increasing the maximum permissible fiber stress in zinc were considered. Cold rolling, which' increases the stiffness and tensile strength, was found to decrease the resistance to slow flow. Alloying, therefore, provided the only feasible means of obtaining the desired result, It was recognized that the improvement secured by the solid solution of natural impurities was insufficient. A series of alloys was outlined, therefore, in which a number of metals were added separately and together. The sheets rolled from these alloys were tested under

Jan 1, 1930

By B., Hoyaux

A first requirement for assessing the safety of a rock slope, either artificial or natural, particularly if the rock behaves in an elastic-brittle manner, is a proper knowledge of the distribution of stresses within the slope and their development with time and advancement of workings.

Jan 1, 1972

By E. J. Duggan

THE mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. DESCRIPTION OF ORE The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chalcopyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the dose association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. HISTORY Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From 1926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and' 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for molybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill 10,000 tons per day, but it was not long before 12,500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. To increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. CRUSHING There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. 1) and No. 2, of 15,000 tons capacity (Fig. 2).

Jan 1, 1942

By R. S. Archer

IN the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the heat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis; heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while iii others, especially ill those whose grain is unusually fine or in which the final hardening heat, has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters.

Jan 1, 1919

By D. Mizer, J. B. Clark

In a recent investigation of the entire magnesium-yttrium phase diagram, Gibson and Carlsonl report the maximum solid solubility of yttrium in magnesium as 8.0 wt pct Y at 1050°F (565°C). However, independent studies of the precipitation in magnesium-yttrium alloys, 2 conducted prior to the publication of the above phase diagram, indicated a greater solid solubility of yttrium in magnesium. Accordingly, the magnesium-rich region of the diagram was re-investigated to determine more accurately the liqui-dus, solidus, and solvus of the magnesium solid solution in this system. Metallography and thermal analysis were chosen as the best corroboratory methods for accurately determining this region of the diagram. A magnesium-yttrium master alloy was prepared from yttrium of 99.9 pct purity and singly sublimed magnesium of 99.9 pct purity. Subsequently, the twelve magnesium-yttrium alloys shown in Fig. 1 were prepared using standard alloying procedures for magnesium. Metallographic samples of the alloys were heat treated under an SO, atmosphere in an electric furnace capable of control within ±3oF of the desired temperature. Alloy samples for the metallographic determination of the solvus, and for the precipitation studies were solution treated at 1000° F for 16 hr. Subsequent aging times for the solvus determination varied from a minimum of 6 hr for the higher temperatures up to 816 hr for lower temperatures. Periods of 30 min at temperature were used to generate liquation for the metallographic placement of the solidus and eutectic horizontal. The liquidus and the eutectic horizontal were determined by thermal analysis. Simple time-temper- ature heating and cooling curves were obtained from 10-g alloy samples heated and cooled in a well-insulated electric furnace. An Iron-Constantan thermocouple was placed in direct contact with the sample. The thermocouple did not contaminate the alloy sample since metallographic examination showed that the alloy melt did not wet or attack the thermocouple. The heating and cooling rates were approximately 5 to 8OF per min. The standard metallographic procedures for magnesium were used in polishing and etching the magnesium-yttrium alloys studied. Glycol etchant* was etchant was used to reveal precipitate in the solvus determination. The redetermined magnesium-rich region of the magnesium-yttrium diagram is shown in Fig. 1. The

Jan 1, 1962

By J. D. Price, W. M. Bertholf

THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers.

Jan 12, 1954