Search Documents

By Robert Pike

THE first authentic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1.869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is said to have worked out his process. Jacobi1 in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein's process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeSO4 + (NH4)2S04. Lenz2 described ?some properties of electrolytically precipitated iron. He used Klein's bath, FeSO4 + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By H. O. Hofman

The object of refining copper in the reverberatory furnace is to obtain a metal which will have the highest attainable degree of malleability, ductility and electric conductivity, and present at the same time a level surface when it solidifies in the mold after casting. These desirable physical properties are governed by the character of the impurities and the forms in which they are present, by the amount of cuprous oxide retained by the copper, by the quantity of gas held in solid solution, by the casting-temperature, and by the thickness of the casting. The effects of impurities, of cuprous oxide and of gases upon the mechanical properties of copper have been studied by Hampe1 in his classical paper " Colitributions to the Metallurgy of Copper." The most recent research into the effect of metals upon the electrical conductivity of copper is that of Addicks. 2 The influence of cuprous oxide upon the electrical conductivity has been investigated by Walker3 and Addick. 4 The absorption of gases has received attention by Hampe: Stah16 and Heyn 7 The effects of casting-temperature have been noted by Stahl.8

Jan 1, 1908

By Edward Keller

Someone some time ago remarked that some chemists still insist on telling us how to determine copper by the electrolytic method. The writer must confess that he believes that everything is not known definitely as yet as to how the exact amount of copper is determined in such material as purest commercial electrolytic copper. Some of us are not yet convinced that the pure copper atom is at all times deposited from an acid solution and that no oxygen or hydrogen will, under certain conditions, accompany it. Difficulties with impurer material are frequent, but erroneous results are not always apparent, since these do not speak so readily for themselves as those in the first case. By this is meant that if a chemist finds 100 per cent. of copper in electrolytic copper it is pretty certain that he perceives the result to be wrong, while if he finds 0.1 per cent. of copper too much in a very impure material he is far more likely to be unconscious of his error. These, in a wide experience, are frequent happenings and the writer has always looked with interest to publications on this subject. In turn, he feels justified in giving to others a few of his own observations. Up to a few years ago there were two methods of electrolytic copper assay in technical use, which had in common, that the amount of copper deposited on the cathode did not exceed 2 g., and they differed in that, for the one a large sample1 (20 to 80 g.) was taken from the general sample by a splitting device, dissolved, and from the solution a small portion (to contain 1 or 2 g. of copper) measured out for the electrolytic deposition; in the other method the copper was determined, generally in 1-g. portions of the separated coarse and fine portions of the sample, all of which passed a 16 or 20-mesh screen, being accomplished by a 40-mesh screen,

Jan 1, 1914

By Marvin P. Barnes

Definition The term mineral inventory is a relatively new designation, born of the computer age and grown to common usage with the development of computer techniques for extending drill-hole sample values to regularly gridded data blocks representing in situ mineral values. The term has been generally accepted by geologists and engineers because it has a precise meaning which avoids many of the ambiguities of ore reserve. A mineral inventory is an estimated inventory of mineral in place and is usually achieved by dividing the deposit into regularly spaced gridded blocks to which are assigned estimated values using various extension techniques. A mineral Inventory makes no presumptions about the minability of the blocks or their cutoff grade. A mineral inventory estimate may be good or poor according to how much is known about the deposit, how extensively it has been sampled, and what techniques have been employed to assign estimated grade to the blocks Such an inventory, however, does not change with time, economic conditions, or mining technology, but only with new and better data and methods. Thus, the mineral Inventory is an excellent designation for describing mineral value distributron within a deposit's geological setting

Jan 1, 1979

By D. T. Goettge, E. L. Robinson

The phase changes occurring in low carbon steel during hot strip mill rolling are shown to be metallurgically significant when related to commonly used temperature control points, particularly finishing and coiling temperatures. In combination, these temperatures are shown to have an important influence on the level and uniformity of hardness, grain size, and carbide characteristics of the finished hot and cold rolled sheets. PRODUCTION of wide flat-rolled products ordinarily requires a number of operations in sequence to prepare the material for shipment to the customer. Most products are tailor-made for specific end uses, with each operation contributing certain properties to the finished material. Since the characteristics imparted to the semifinished product by a given step in processing carry through to the finished product in varying degrees, it is important that the intermediate stages of production of flat-rolled strip be carried out with the same care which characterizes the last or finishing operations. The step of hot strip mill rolling is common to the production of all of the various types of flat-rolled product; therefore, the hot strip rolling is an especially important point at which to recognize and control those variables which have an effect on the surface characteristics and metallurgical properties of the finished product and which influence the ease of conducting subsequent operations. Orders entered at a producing mill usually show an end use or describe an article or part into which the ordered product is to be fabricated. Applying his experience as to the properties necessary in a finished sheet to suit the end use and to perform successfully in the fabrication involved, the metallurgist selects a steel of suitable composition and deoxidation practice, and slabs of appropriate dimensions are produced for rolling on the hot strip mill. At this stage of processing, the metallurgist faces the problem of controlling hot strip mill practice in the light of his diagnosis of the properties necessary to meet the end use, paying due attention to the accompanying problem of producing a strip which can meet processing requirements on subsequent units in the mill. It is the purpose of this paper to describe some of the factors which he must consider in solving these problems and to indicate some of the principles which guide him. Equipment, Physical Requirements of the Strip, and Temperature Measurement The metallurgist must, of course, be familiar with the physical layout of the mill, the temperature-measuring equipment available, and the physical requirements of the hot strip product before he can apply his metallurgical knowledge to the problem; hence, the first section will consist of a brief discussion of these matters. The usual hot strip mill consists of reheating furnaces, five or six roughing stands including a scale-breaker, holding table, and second scalebreaker, six-stand finishing mill, runout table with spray cooling facilities, and coilers. A schematic diagram of a typical layout is shown in Fig. 1. Slab temperatures are primarily a function of heating time and furnace temperatures, while mill speeds, spray practice, drafting practice, available water pressure, temperature of the cooling water, cross sectional dimensions of the strip, coil size, and equipment limitations, either singly or in combination, determine what rolling temperatures are practical on a given hot strip mill unit. Thus, it is possible that a set of temperatures which can be utilized successfully on one mill cannot be used on another. However, adjustments in temperatures and rolling practice can usually be made to develop the desired metallurgical properties. In addition to the metallurgical properties developed through proper temperature control, the hot strip mill must also provide strip with certain physical attributes which may be summarized as follows: Strip Cross Section—The strip contour should conform to a section which will give the best results in the cold reduction operation. This is generally recognized as a strip with 0.001 to 0.003 in. crown or shoulder-to-shoulder convexity depending on width, and freedom from concave, flat, or wedge-shaped cross sections which cause metal buildup in cold reduction. Excessive drop off in thickness at the edges can also be very detrimental in cold reducing to light gages. Gage, Width, and Camber—All of these must be controlled. For example, rundown or increasing thickness from the front to the back of the coil results in nonuniformity in the thickness of hot-rolled sheet product and in added difficulty with gage and welds in cold reduction. Similarly, excessive width variation is the cause of guide trouble and excessive edge scrap at later stages of processing, while excessive camber is the source of a variety of processing troubles. Type of Oxide—Product intended for pickling should have a predominance of the type of oxide most easily removable in sulfuric acid. It is generally recognized that this type is obtained by use of maximum table cooling water and cold coiling

Jan 1, 1957

By Warren J. Jackson, John L. P. Campbell

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Although the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time. All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. The Gamma-ray Curve The measurement of gamma-ray intensities is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is filled with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By John L. P. Campbell, Warren J. Jackson

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Although the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time. All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. The Gamma-ray Curve The measurement of gamma-ray intensities is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is filled with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By J. W. Spretnak, G. W. Powell, J. H. Bucher

Tlze room-temperature tensile fracture oj smooth, round specitnens of three ultrnhigh- strength steels tempered to a wide range of strength levels was studied by means by light and electron-microscopic examination of the fracture surfaces. The fracture of AISI 4340 and 300 M at all the strength levels studied, and H-11, except after tempering at 1200° and 1300°F, occurs in three stages. The initiation of fracture is internal (except in some lightly tcmpeved specimers in which fracture is initiated at surface flaws), and is nucleated largely by separation at metal-second phase intevjaces. TIze voids grow and, coalesce to form a crack. When the crack has reached a sufficienl size, rapid propngutio~z ensues. Failure in this stage of fracture usually occurs by dimpled rupture of inicroshear stefis. In the case of H-11 tempered in the 1125° to 1300°F range, fracture in the shear steps is predominantly by concentrated deformation without void formation. The termination of fracture is usually occomplished by the formation of a shear lib in which fracture occurs by shear dimpled rupture. In the case of H-11 tempered at 1200° and 1300°F, no shear lip was obserued, and the radial elelments extend to the surface—a true termination slage does not exist. ThE tensile fracture of several metals and alloys has been investigated.2-4 In the case of polycrystal-line materials, cup-cone fracture usually results. The mechanism of cup-cone fracture may be summarized as follows.5 Cavities are formed in the necked region of the specimen. They usually are initiated by inclusions or second-phase particles. The cavities extend outwards by means of internal necking, and a crack lying about perpendicular to the length of the specimen is formed in the necked region. Subsequent crack growth occurs by the spread of bands of concentrated plastic deformation inclined at an angle of 30 to 40 deg to the tensile axis. Cavities are formed in the bands of concentrated deformation. The deformation bands zigzag across the bar with the net result that mac-roscopically the crack extends about perpendicular to the specimen axis. The final separation, or cone formation, appears to occur by continued crack propagation along one of the deformation bands out to the surface of the specimen. The micromechanics of the tensile fracture of ultrahigh-strength steels have not been thoroughly investigated. Larson and carr6,7 studied the tensile-fracture surfaces of AISI 4340 with a low-power microscope and reported that three stages of fracture could be observed in general. A centrally located region characterized by circumferential ridges, an annular region characterized by radial surface striations, and a peripheral shear lip were found. It was first pointed out by 1rwin8 that the central region is very probably one of fracture initiation and slow growth, and that the annular, radially striated region is one of rapid crack growth. Presumably the crack grows slowly, assuming roughly a lenticular shape, until it is large enough for the initiation of rapid propagation. In this investigation, it was attempted to determine the fine-scale aspects of the room-temperature tensile fracture of some ultrahigh-strength steels, and to relate the variation in fracture mode with microstructure. The steels studied were AISI 4340, 300M, and H-11 tempered to a wide range of strength levels. I) EXPERIMENTAL PROCEDURE The compositions of the steels studied are given in Table I. The steel was received in the form of hot-rolled bar stock 5/8 to 1 in. in diameter from which oversized specimens were machined and heat-treated. The heat treatments employed are given in Table 11. Subsequent to heat treatment, the specimens were ground to the final dimensions and stress-relieved by heating for 1 hr at 350°F (with the exception of the as-quenched steel). Standard smooth round specimens of 0.252-in. diameter and 1-in. gage length were tested in a Tinius Olsen Universal Testing Machine using a cross-head speed of 0.025 in. per min. The relatively coarse aspects of the fracture topography were determined by light-microscopic examination of sections through the fracture surface of nickel-plated specimens. A direct carbon-replication technique9 was used in the electron-microscopic study of the fracture surfaces. The replicas were examined in the electron microscope, and stereo pairs of electron micrographs were taken. The stereo pairs were then examined using a Wild ST4 Mirror Stereoscope. Carbide and inclusion particles extracted in the replicas were analyzed by selected-area electron diffraction. II) EXPERIMENTAL RESULTS The mechanical testing data are summarized in Table 111. The values reported are the average of

Jan 1, 1965

By H. W. Mead, C. E. Birchenall

The rates of growth of graphite nodules in cast irons are calculated for a model of a growing graphite sphere surrounded by a shell of austenite through which carbon and iron are diffusing. The carbon is supplied by a cementite-austenite mixture at the outer edge of the shell. The calculated rates from carbon diffusion agree fairly well with the measured values, but the rates based on iron self-diffusion are much too low. Because the iron must be removed for the process to continue, o plastic deformation mechanism is suggested. THERE has been an unfortunate tendency in the literature of growth and dissolution reactions to identify the slope of a plot of the logarithm of the growth or dissolution rate vs reciprocal of temperature with the activation energies determined by diffusion measurements in chemically similar systems. If the solubility limits at the growing or dissolving phase interfaces change appreciably with temperature, such procedures may lead to serious errors in specifying the mechanisms controlling the rates of these processes. A reaction involving the simultaneous growth of graphite from and dissolution of cementite in austenite will be discussed here to show that substantial oversimplifications have been made in earlier studies of this process. From a dilatometric study of the overall y-range graphitization process, Bunin and Danil'chenko' found an apparent activation energy of 90 kcal per g-atom. They concluded that, since this value was much nearer the approximately 68 kcal per g-atom observed for self-diffusion in pure iron than it was to 32 kcal per g-atom for diffusion of carbon in iron, the rate-controlling process must be the diffusion of iron away from the growth interface to provide space for graphite to grow. Bunin and Salli' bolstered this agreement with the observation that graphite forms preferentially at surfaces, cracks, and pores where free volume is present initially. Ziegler, Meinhart, and DeaconQ ad found an apparent activation energy for graphitization of 98 kcal per g-atom. This value, like that of Bunin and Danil'chenko, applies to nucleation and growth occurring simultaneously. It is not generally assumed that nucleation is entirely diffusion-controlled. Treatments such as prior cold-working and prequenching, which strongly affect the rate of graphitization, would be expected to have little effect on diffusion processes occurring at the graphitization temperature. In any case 90 kcal per g-atom is not particularly close to the 54 kcal or lower to be expected for diffusion of iron which is carbon-saturated.' The presence of silicon in iron is said to reduce the activation energy for diffusion,' so its presence in cast irons would be expected to have a similar effect. The growth rates of nearly spherical graphite nodules have been studied by Brown and Hawkes." The initial rate of growth before impingement of adjacent carbon-depleted areas was found to be parabolic, and rate constants were measured at several temperatures. Their apparent activation energy for the growth process only was roughly 45 kcal per mol. Burke and Owen' made growth-rate measurements on several alloys, recording appreciable induction periods, initial nucleation rates, and average radial growth rates based on an assumed linear rate of radial growth. They found that increased silicon content increases the ovel-all reaction rate and the initial rate of nucleation, and decreases the induction period. Assuming 1) spherical nodules. 2) constant volume rate of nucleation, 3) austenite in equilibrium with cementite at positions where the cementite is not depleted, and 4) a constant diffusion distance during the growth of a nodule, they calculated an apparent overall activation energy of 68 kcal per mol, which was related to an activation energy for nucleation of 79 kcal per mol and activation energy

Jan 1, 1957

By A. Faison Dixon

In India the production of mica, which in other countries is of very minor importance, is one of the staple, long established industries, and ranks high in the statistics of mineral products. Nearly two-thirds of the mica of commerce comes from India. The Indians have used mica for glazing and decorative purposes through many centuries. About 14,000 men are employed in and about the mines, and the indigenous and primitive mode of mining is still followed; but, by reason of the exhaustion of the surface supply hitherto won without intelligence or capital, it will not be many years before the present interesting and casual methods will be replaced by a less archaic and more profitable system. India on the whole has little mineral wealth, but the unique resources of its mica-fields, cheap labor, and favorable natural conditions render it unlikely that any other country can ever more than temporarily contest her leadership in the production of this one minor but essential mineral. Mica plays a small but indispensable rôle in a variety of fields of dissimilar application. Its use and value depend upon characteristics which different kinds of mica have in varying degrees, each kind being adapted to its own special purpose. Its well-known characteristics of transparency, flexibility, elasticity, toughness, high dialectric strength, perfect flatness, ease of splitting into thin films, ability to stand high heat and sudden changes in temperature, give it value in many industries. No other substance, natural or artificial, has the same combination of qualities. The oldest use of mica is in glazing. By reason of the improvements in annealing glass, this is not now of great importance, but mica is still employed for the covers of ikon images in Russian churches, the windows of anthracite stoves, compass

Jan 1, 1914

By Charles Clayton

CAST-STEEL runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Foley1 found not only the usual ingot structure, but zones of Widmannstattian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent, nickel and 0.350 per cent. carbon and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. The macrostructure, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregation of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of- the runner and in all parts of the individual grains. I he tipper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to- some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 3, 1920

By Doll. H. G.

THIS paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole, By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simple and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, time-saving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given.

Jan 1, 1942

By Leon W. Dupuy

A brief elemental discussion of the fundamental factors involved in diamond drilling often fills a need, particularly when a mine operator is contemplating for the first time an exploratory drilling campaign. Mr. James A. Barr, of the Mining Methods Committee of the Institute, has suggested that many engineers must undertake a drilling program of one kid or another and, in the case of diamond drilling, sometimes even are at a loss as to how to start correspondence. The Bureau of Mines has acquired much experience in managing exploratory diamond-drilling activities. Its activities in diamond drilling included exploring for potash in Texas, Utah and New Mexico1-' during the 1920's. The Strategic Minerals Exploration program was started in 1939 and was materially expanded during the war to include critical and essential minerals. At the peak of its war-time activity more than 200 engineers were employed, a majority of whom supervised diamond drilling. Many of them had little experience with such work prior to their employment with the Bureau, and it was necessary to instruct them in their duties. The purpose of this paper, therefore, is to present the fundamentals of exploratory diamond drilling from the viewpoint of management in such a way that they will Serve as a basis on which those beginning exploratory diamond drilling may build an experience and acquire ability to direct exploration as they gain that experience. Selection of Method of Drilling Selection of the method of drilling is governed by the type of material to be penetrated and by the type of sample needed to determine the quality and importance of a deposit. Types of drills that might be used for a given job include diamond drills, churn drills, hand auger drills, power auger drills, bucket drills, and rotary drills (sometimes called "seismograph rigs"). Each type has a specific field in which it is most useful. While the Bureau of Mines utilized all the types of drilling mentioned, diamond drilling was used on a majority of its exploratory projects. Factors Governing Selection of Diamond Drilling The prime consideration in selecting a method of drilling is first to determine what results are desired and then to choose a method that will furnish reliable data in the ground to be penetrated. Use of diamond drills permits recovery of a core as well as sludge at a comparatively low cost. The core provides an excellent means of studying the formation being drilled and furnishes much information that would be difficult to obtain otherwise. Diamond drills will recover a satis-

Jan 1, 1948

By Leon W. Dupuy

A brief elemental discussion of the fundamental factors involved in diamond drilling often fills a need, particularly when a mine operator is contemplating for the first time an exploratory drilling campaign. Mr. James A. Barr, of the Mining Methods Committee of the Institute, has suggested that many engineers must undertake a drilling program of one kid or another and, in the case of diamond drilling, sometimes even are at a loss as to how to start correspondence. The Bureau of Mines has acquired much experience in managing exploratory diamond-drilling activities. Its activities in diamond drilling included exploring for potash in Texas, Utah and New Mexico1-' during the 1920's. The Strategic Minerals Exploration program was started in 1939 and was materially expanded during the war to include critical and essential minerals. At the peak of its war-time activity more than 200 engineers were employed, a majority of whom supervised diamond drilling. Many of them had little experience with such work prior to their employment with the Bureau, and it was necessary to instruct them in their duties. The purpose of this paper, therefore, is to present the fundamentals of exploratory diamond drilling from the viewpoint of management in such a way that they will Serve as a basis on which those beginning exploratory diamond drilling may build an experience and acquire ability to direct exploration as they gain that experience. Selection of Method of Drilling Selection of the method of drilling is governed by the type of material to be penetrated and by the type of sample needed to determine the quality and importance of a deposit. Types of drills that might be used for a given job include diamond drills, churn drills, hand auger drills, power auger drills, bucket drills, and rotary drills (sometimes called "seismograph rigs"). Each type has a specific field in which it is most useful. While the Bureau of Mines utilized all the types of drilling mentioned, diamond drilling was used on a majority of its exploratory projects. Factors Governing Selection of Diamond Drilling The prime consideration in selecting a method of drilling is first to determine what results are desired and then to choose a method that will furnish reliable data in the ground to be penetrated. Use of diamond drills permits recovery of a core as well as sludge at a comparatively low cost. The core provides an excellent means of studying the formation being drilled and furnishes much information that would be difficult to obtain otherwise. Diamond drills will recover a satis-

Jan 1, 1948

By Francis Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other indus-tries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phos-phorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater impor-tance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appear-ance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1935

By F. E. Smith, David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and¬-sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) Organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved salts in water; (3) pseudo liquids obtained by suspending solids, such as sand, in water, and (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended-sand pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are con¬tinuous, vertical and horizontal currents of the separating medium occur as either part of the process or unavoidedly produced by the intro¬duction of feed and withdrawal of products, so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary to get the recoveries and grade of product desired. Sizes usually cleaned are plus %6-in. or plus 3-in. in the United States and plus 36-in. in Great Britain. Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about % in. is made difficult by viscosity effects and hence at the present time cleaning is confined to the coarser . sizes. Technical advances in the art of cleaning coal by dense-media

Jan 1, 1943

By E. M. Norris

DURING the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation;(5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol.

Jan 2, 1922

By Hugh S. Spence

THE use of natural feldspathic rocks, as opposed to straight feldspar, for ceramic purposes is not new. "Cornwall stone," a semi-kaolinized granite containing fluorite, has long been used by the English pottery trade instead of feldspar, and "Carolina stone," a similar rock, is now being offered to the American trade. A recent report of the U. S. Bureau of Mines states that trachyte, a glassy volcanic rock, is being used in California instead of feldspar in ceramic bodies. In Germany, phonolite and basalt have been investigated, and possibly also used, as ceramic raw materials, and extensive research has been conducted in Russia in recent years looking to the utilization of the immense bodies of nepheline syenite of the Kola Peninsula, which is the host rock of the apatite deposits now being exploited on a large scale in the Murmansk region; the nepheline is recovered as a by-product of the concentration of the apatite. Long used principally as a raw material for the pottery and allied industries, where, in bodies, glazes, enamels, etc., it serves as a fluxing ingredient and forms, on firing, a glassy bond with the more refractory clay, flint and coloring particles, feldspar has been finding ever increasing employment in glass. In 1936, over half of the nearly quarter of a million tons of feldspar sold in the United States went to the glass trade. Its usefulness for this purpose is due to the resistance to thermal shock which it imparts to glass products, particularly bottles, containers and tableware, because of its alumina content, which averages from 16 to 20 per cent. Active search has been made on the American continent during the past few years for other minerals of feldspathoid type, with comparable or higher alumina content, that may be suitable for glass and other ceramic purposes. One of the most important results of this work has been the delimiting in central Ontario of large bodies of nepheline syenite of excellent ceramic grade.

Jan 1, 1938

By J. D. Alexander, W. L. Martin, J. N. Dew

This paper presents data obtained using a flood-pot technique to determine the fuel available and the corresponding theoretical air requirements for in situ combustion of crude oils. Since the technique is relatively quick and easy, it is a practical and convenient tool for evaluating reservoirs as fireflood prospects. It is also a research tool which facilitates systematic study of the variables affecting fuel availability and corresponding air requirements. The understanding of these variables is of prime importance to those concerned with the technical and economic development of in situ combustion as an oil-recovery process. The experimental results show conclusively that the fuel available for in situ combustion is not a constant but, rather, varies with crude-oil characteristics, porous-medium type, oil saturation, air flux and time-temperature relationships. Thus, the fuel availability for specified field applications should be determined using actual reservoir crude and core material and the process conditions expected during in situ combustion in the reservoir. INTRODUCTION In situ combustion is a thermal process for recovering crude oil from reservoirs. The thermal energy released during the combustion of a small amount of the oil in place aids in the displacement of the remaining oil. Numerous articles have been published describing the in situ combustion process giving detailed results of laboratory and field experiments.10 In order to engineer an in situ combustion project, a number of important factors must be considered and determined. These factors include: (1) the amount of fuel consumed per unit of reservoir volume swept by the combustion zone, (2) the composition of the fuel consumed, (3) the amount of air required to consume this fuel, (4) the portion of the reservoir swept by the combustion zone, (5) the appropriate air-injection rates and pressures, (6) the amount of oil that will be recovered, (7) the rate of oil production and (8) the operating costs. Nelson and McNiell1 recently have described a procedure which utilizes laboratory combustion-tube data as a basis for the calculation of some of these design factors. Various authors have attempted to describe the in situ combustion process mathematically, and considerable progress has been made. Analytical solutions to the problem of heat transfer from a moving combustion front have been obtained for linear and radial systems."-' All of the published results involve the assumptions that: (1) fuel concentration is constant throughout the reservoir, or that fuel concentration is inversely proportional to the velocity of the front for a given rate of oxygen consumption; and (2) the fuel reacts instantaneously with injected oxygen, while liberating a constant amount of heat per unit weight of fuel at all temperatures. It seems both desirable and reasonable to test the validity of these assumptions experimentally. This paper presents laboratory data which were obtained by means of a "fire flood-pot" method for determining fuel availability and composition, and the corresponding theoretical air requirements for in situ combustion of crude oils under variable conditions. The mechanics of the method are similar to a conventional tube-run experiment.' The important differences involve the size of the reservoir model used and the method for providing the experimental environment. The new method subjects conventionally-sized core samples or unconsolidated sands to a programmed environmental sequence similar to that experienced by a similar volume of rock during the approach and passage of a combustion front in a long tube or in an oil reservoir undergoing in situ combustion. Restored-state samples can also be used. The small samples and relatively simple techniques involved allow an experiment to be set up, run and calculated in about three 8-hour days. This is a considerable improvement over long-combustion-tube techniques which can require several days to run and several more work days to set up and calculate. All the runs presented were run at 40-psig injection pressure. Pressure was not considered as a variable for these experiments, since we previously had found that it had only a small effect on fuel availability up to 600 psig.APPARATUS AND MATERIALS APPARATUS The fire flood-pot apparatus consists of a consolidated

By L. G. Austin, P. T. Luckie, R. R. Klimpel, R. S. C. Rogers

1. INTRODUCTION The Bond method(1.2) for sizing tumbling ball mills has been used successfully for many years. The primary purpose of the Bond calculation is to predict the mill size and mill power to give a desired capacity (Q tph) from a wet overflow ball mill in normal closed circuit operated with a circulation ratio of 2.5. The input to the calculation is the make-up feed size characterized by the 80%-passing size in micrometers (xG), the desired circuit product size characterized by the 80%-passing size (xQ), and an empirical grindability number (the standard Bond Work Index) determined by a standard test. A series of empirical correcting factors(2) are used to convert the results to open-circuit or dry grinding in grate discharge mills. The Bond method has two major engineering advantages: (i) it is very simple; (ii) experience has shown that it works for many circumstances, as a reasonable approximation, because it is based on direct conversion of test data to results measured on industrial mills. There are four main disadvantages of the Bond method. First, there will be a range of error for any specific mill and material and set of operating conditions because the method does not explicitly include several variables which are obviously important: (i) recycle ratio and classifier efficiency (ii) mixture of ball sizes in the mill (iii) variations of residence time distributions with mill geometry and slurry density (iv) lifter design (v) slurry rheology (vi) different underfilling or overfilling of the mill as flow rate is changed. Second, the Bond method explicitly assumes that specific grinding energy E is not a function of ball load, whereas industrial practice and laboratory tests(3) show that the specific grinding energy (to go from a specified feed to a specified product) is less for lower ball loadings than the ball loading for maximum mill capacity. Third, the method uses only the 80% passing size of circuit feed and product to characterize the size distributions, whereas mill capacity in general must depend on the shape of the feed size distribution and the product size distribution. The prime example of this is the use of the reverse closed circuit which removes some fraction of the make-up feed before it is

Jan 1, 1982