Search Documents

By C. O. Burgess, W. D. Forgeng

The results of an investigation of the ternary system iron-chromium-silicon were reported in 1936 by the present authors.l Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers2'3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon in molten iron-chromium-silicon alloys. Tofaute and his coworkers5'6 have made detailed studies of the iron-chromium-carbon system, which will be referred to later. Materials and Methods Materials.—The iron, chromium and silicon used were essentially the same as those used in the investigation of the ternary system.l The

Jan 1, 1938

By C. O. Burgess, W. D. Forgeng

The results of an investigation of the ternary system iron-chromium-silicon were reported in 1936 by the present authors.l Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers2'3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon in molten iron-chromium-silicon alloys. Tofaute and his coworkers5'6 have made detailed studies of the iron-chromium-carbon system, which will be referred to later. Materials and Methods Materials.—The iron, chromium and silicon used were essentially the same as those used in the investigation of the ternary system.l The

Jan 1, 1938

By Ancel St. John

DURING a session on coal and coke at the February, 1926, meeting of the American Institute of Mining and Metallurgical Engineers, the writer called attention to the important work on the X-ray analysis of coal1,2 being carried on in England by C. Norman Kemp and his associates. This aroused so much interest that a paper on the subject was requested for the October meeting. It has seemed advisable to make this paper a preliminary survey of the present status in the application of X-ray methods to coal problems and to follow it from time to time with further articles as the art develops. A survey of this sort naturally divides itself into two parts, radioscopic analysis of the distribution of constituents through the body of the coal, and diffraction analysis of the state of association of the elementary components. In this article the subject matter concerning radioscopic analysis has been drawn almost entirely from the writings of Kemp and his associates and the illustrations have been specially furnished by him. It is a pleasure to record here a great indebtedness for this courtesy and cooperation. The subject matter and illustrations concerning diffraction analysis are taken from the author's unpublished researches.

Jan 10, 1926

By Alexander Field

INTRODUCTION THE Bureau of Mines is investigating the problem of slag viscosity, its variation with the temperature and with the composition of the slag, and its effect upon the distribution of the sulphur between molten iron and slag, as introductory to a series of contributions to the theory of the metallurgical processes. The method of measurement, viscosity, apparatus, furnace and other accessories mentioned in this paper have been described fully in a Bureau of Mines report.1 THE LITERATURE ON SLAG VISCOSITY The viscosity of blast-furnace slag had not been measured previous to the investigation described in this report. A number of investigators have determined the "fusibility," or softening temperature, of slags by means of the cone method or, other deformation method, but these methods supply only limited information regarding the temperature-viscosity relations.-of the slag in question. Any deformation method that may be employed indicates only the temperature at which the slag attains a more or less definite viscosity, the magnitude of the value obtained depending on the method used. For details of the various methods used by different investigators, see, the Bureau of Mines paper already referred to. An isolated measurement by Doelter on a single mixture at 1,300° C. represents the highest temperature reached in the various viscosity investigations previous to those described in this report, in which results have been referred to absolute units. Arbitrary deformation tests have of course been made at much higher temperatures.

Jan 2, 1917

By Ulick R. Evans, Maurice Cook

The structural changes in metals brought about by annealing follow-ing a deformation at a low temperature has been the subject of many investigations. No less than eleven metals and alloys have been studied in some detail; namely, aluminum, tungsten,2 iron,3 copperI4 gold, zinc,6 cadmium, tin: lead: brass,1° and cupronickel. As a result, it is possible to frame a qualitative statement of the effect of the degree of deformation and the temperature of annealing on the structure finally attained.

Jan 1, 1925

By A. H. Grobe, F. N. Rhines

AT elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible' and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscale forma¬tion) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detail5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the I-b and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 4o alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. EXPERIMENTAL PROCEDURE Silver.-The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By H. Conrad, V. V. Damiano, G. J. London

The slip mode activated during the c axis compression of single crystals of commercial-purity ingot SR beryllium, high-purity (twelve-zone-pass) beryllium, and Be-4.4 wt pct Cu and Be-5.2 wt pct Ni alloys in the temperature range of 25° to 364°C was determined using two-surface slip trace analysis, slip-step height analysis, and electron transmission microscopy. All three techniques indicated the occurrence of copious pyramidal {1 122) (1123) slip in the alloys over the entire temperature range, the amount increasing with temperature. Pyramidal slip was also indicated in the high-purity beryllium by slip trace analysis and electron transmission microscopy, but the amount was somewhat less than in the alloys. For the commercial-purity ingot crystals, only a very small number of pyramidal slip lines were observed, and these were in the immediate vicinity of the fracture surface. No pyramidal dislocations could be detected by electron transmission microscopy in this material. Dislocatransmissiontions with Burgers vectors [0001] and +(ll20) were identified by electron transmission microscopy inthe (1122) slip bands, as well as those with the j (1123) vector. This was interpreted to indicate that the edge components of the 3(1123) vector dislocations activated during c axis compression dissociate upon unloading according to the reaction i (1123) — [0001] + 3(1120) THE microstrain c axis compression of single crystals of commercial-purity ingot SR beryllium (99.6 pct), high-purity twelve-zone-pass beryllium (99.98 pct), Be-5.24 pct Ni and Be-4.37 pct Cu alloys was described in a previous paper.1 This paper covers in detail the analysis of slip traces observed on two mutually perpendicular lateral surfaces of these specimens, and a detailed description of transmission electron microscopy studies performed on foils cut from the bulk crystals after they had been deformed to fracture in the c axis compression. Observation of slip traces on single surfaces of deformed single crystals are generally insufficient to positively identify slip or twinning modes. The use of two carefully cut and oriented perpendicular surfaces can greatly aid in the positive identification and index- ing of slip traces, although even this technique may be quite inadequate if more than one type of slip system operates and if an insufficient number of traces are observed on the surfaces. The problem is greatly simplified for symmetric cases like that for c axis compression of an hep crystal such as beryllium, in which the operating slip systems are all equally inclined to the direction of the applied stress, and each slip system of a given slip mode has an equal chance of operating. For such cases, the traces of any given slip mode observed on the surfaces cut parallel to the c axis are symmetrically tilted about the c axis. It is therefore possible to quickly determine whether one or more slip modes are operating. Confirmatory evidence in support of the observations made on the external surfaces can be obtained from foils cut from the deformed crystals and examined by transmission electron microscopy. This latter technique serves to identify not only the operating slip plane but also the Burgers vector of the dislocations which participate in the slip. For this purpose, a simplified technique based upon a double tetrahedron notation is used in the present paper. The planes and directions in the hep lattice are all designated by letters rather than indices and extinction conditions are easily determined if the Burgers vector lies in the plane contributing to the diffraction. RESULTS 1) Slip Trace Analysis. The standard (0001) stereo-graphic projection of beryllium is shown in Fig. 1. The two mutually perpendicular, lateral surfaces of the compression specimen are represented by the diametrical planes AA' and BB', also referred to as surface A and surface B. For the specific case represented (a Be-5.24 pct Ni specimen deformed by c axis compression at room temperature), the A surface is tilted 5 deg to the (10i0') plane and the B surface is tilted 5 deg to the (1120) plane. Two surface trace analyses may be facilitated by examining in turn the intersection of various great circle traces of specific pyramidal planes with two surfaces and comparing the angles made with the (0001) plane with those actually observed on the two surfaces. One then identifies the slip traces by trial and error on a best-fit basis. The (1122) type planes (it was found that slip occurred on these planes) are shown plotted on the stereographic projection in Fig. 1. One obtains directly the angles between the (0001) plane and the {1122) traces by measuring the angle from the periphery to the point of intersection along the lines

Jan 1, 1969

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By Bror Nordberg

SAND and gravel are unconsolidated granular materials resulting from the natural disintegration of rocks. The two materials nearly al- ways occur together, variably proportioned in widely available de- posits. A commercial sand comprises the fine granular material, usually less than f in. in diameter (ASTM Designation C58-28), and gravel consists of the coarse, granular material larger than sand (ASTM Designation C125-46T). Gravel falls within the range of 1/4 in. and a top size usually of 3 ½ in. Chemical definition is impossible. Sand and gravel are always of secondary origin. They were formed from various massive rocks through the action of chemical and mechanical forces; then transported, abraded, washed, sorted, and classified by streams, glaciers, waves, or winds, to be redeposited in beds as they are found. Chief disintegrating forces in the reduction of rocks into granular particles were frost, rain, the dissolving action of acid and alkaline ground waters, the mechanical action of streams and waves, and the action of glaciers. Method of formation and deposition have imparted physical properties to sands and gravels that largely determine the commercial value of the materials for particular use and influence the manner of exploitation. In the early days of the commercial industry, purchasing specifications were relatively lenient but in. the past decade much more rigid quality requirements have had to be met for acceptance by all classes of purchasers. The trend to further severity in requirements is a challenge to the industry that commands full knowledge of the nature of raw materials at hand and skillful application of processing into commercial products. Mechanical strength, the ability to resist disintegration, chemica

Jan 1, 1949

By M. Cohen, W. J. Harris

The recent application of lineal analysislt2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at Ma and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as 'la lowering of Ma, resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (TA) for a sufficient period of time, more austenite may be retained at a given lower Or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th is measured explicitly in terms of the excess austenite (6) that exists in the steel at T,, over and above the amount that is normally present after direct quenching to T,. T, is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (TA) may be above or below M,, and still cause stabilization depending upon the themistry of the austenite. stabilization has been found to occur in the presence of bainite4 and of martensite6,6,7,8 as well as in the absence of either,g The phe-nomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at T~ that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subscquent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6,8 low alloy6s7.8 and high alloy tool steels.10'5 ssa- with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1949

By Clarence Merritt

STAINLESS iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mysterious electrolytic effects or comparatively minute non-metallic inclusions. Many uses for a steel with such excellent physical properties is are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that' the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties, 1,2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties-hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion.3 Monypenny reports that a loss of hardness is

Jan 1, 1932

By Howbert Van Dyne

THE Presidio mine of The American Metal Co. of Texas is situated 45 miles south of Marfa, Texas, a town on the Southern Pacific R. R., and lies approximately 20 miles north of the Mexican border. Communication with the railroad is maintained over a state highway. All supplies for mine and mill are hauled in by truck from Marfa and precipitates and concentrates are freighted to the railroad by the same means and shipped to Selby and El Paso, respectively. The mill is at the town of Shafter, 1 mile from the mine and at approximately 350 ft. lower elevation. The ore is conveyed to it by an aerial tramway which requires practically no power on account of the difference in elevation. The mill is a countercurrent decantation cyanide and gravity concentrating plant of 200 tons daily capacity. Coarse and fine crushing are done at the mill. Two near-by shallow wells in the bed of Cibolo Creek furnish an abundance of water. Power is generated for the mill and town by a Diesel engine plant.

Jan 1, 1930

By J. T. Eash, W. S. Crowell, E. M. Wise

The practice of dentistry, particularly the construction of artificial dentures and "bridges," involves a unique and difficult application of the precious-metal alloys. Appliances used in the mouth are continuously exposed to corrosive agencies which can hardly be described as mild, and must remain free from tarnish and be substantially immune to corrosion. Limitations with respect to space and weight demand high physical properties, while complexity of form requires ease of working. The high corrosion resistance required necessitates the use of alloys of high precious metal content. The usual expedient of resorting to mechanical working to produce the requisite strength and stiffness cannot be utilized because of the frequency of annealing and soldering operations. To meet these difficult conditions manufacturers of dental goods were early led, unknowingly perhaps, to the production of precipitation-hardening or temperable alloys. The excellent properties of iridium-platinum may have suggested the addition of platinum metals to the conventional gold-silver-copper alloys to produce greater strength and hardness. It was found that such quarternary alloys retained their high physical properties after passing through the usual soldering process; i. e., heating to 750° to 800" C. and cooling naturally in the air. Later it was discovered that they could be softened and rendered more ductile by heating to the same temperature and quenching in water. These early examples of precipitation hardening, for years the common knowledge of dental practitioners and laboratory technicians, escaped the attention of the scientific world and discovery of the transformation which was responsible for this hardening was disclosed by the Russian investigators of the system Au-Cu, Kurnakow, Schemtschushny and Zasedatelev~,(~)$ although the optimum conditions for securing good properties in aged alloys were not given attention.

Jan 1, 1932

By C. Z. Serpan, L. J. Wittenberg

The density of liquid plutonium was determined, by a pycnometm'c technique, from 664 to 788°C and exhibited a temperature dependence, which could be expressed as:. P= C17.63 - 1.52 x 10-"t] +0.04 g per cc where t = OC. These density values compare favorably with the values previously obtained by a technique utilizing Archimedes' principle. The apparatus and method were evaluated when the densities 0.f molten tin and bismuth were measured and found to be in agreement with accepted literature values. PLUTONIUM or an alloy of plutonium in the liquid state has been proposed as a fuel for a fast-breeder type nuclear power plant.' Since knowledge of the liquid density of plutonium is required for the proper design of such a system, this study was undertaken. In addition, the density and volume expansion coefficient of liquid plutonium are of interest for comparison with these same properties of the six allotropic modifications of the solid metal. Comstock and GibneyZ were first to report a value for the density of liquid plutonium. The value for only one temperature, 665"C, was calculated from data obtained by the radiography of the meniscus, Fig. 3. Recently, the density at a series of temperatures has been reported by Knight,3 who obtained his values by using a differential volumeter, and by 01-sen, Sandenaw, and Herrik, who obtained their values from measurements of the loss in weight of a tungsten bob immersed in the liquid. The density of liquid plutonium reported here was determined by a vacuum pycnometer method. In an evacuated system, the tips of calibrated tantalum pycnometers were lowered beneath the liquid sur-

Jan 1, 1962

By A. Hultgren, B. Herrlander

The original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between A1 and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880' was free from veining. Bannister and Jones' considered veining in ferrite to be a manifestation of microscopical and sub-microscopica~ inclusions. NorthCOtt,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berg1und. TrittOn (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling. Slight distortion would not allow projecting parts of a growing crystal to join up with atomic symmetry. Hanemann and co-workers showed that veining in ferrite consisted of ridges

Jan 1, 1948

By B. Herrlander, A. Hultgren

The original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between A1 and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880' was free from veining. Bannister and Jones' considered veining in ferrite to be a manifestation of microscopical and sub-microscopica~ inclusions. NorthCOtt,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berg1und. TrittOn (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling. Slight distortion would not allow projecting parts of a growing crystal to join up with atomic symmetry. Hanemann and co-workers showed that veining in ferrite consisted of ridges

Jan 1, 1948

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines of less than 500 h.p. cannot now he included in the category of large gas-engines, and therefore I have not considered engines under that power. Table I.—-" Oechelhauser " Type Gas-Engines. Built or Building by William Beardmore Co., Limited, Glasgow Indicated ! Engines. Horse-Power Type. Nature of Work. Gas Used. 6 2,500 Twin cylinder. Dynamo. Producer. 1 in Single cylinder. Rolling-mill. Producer. 4 1,250 Twin cylinder. Dynamo. Producer. 2 1,250 Single cylinder. Dynamo. Producer. 4 625 Single cylinder. Dynamo. Producer. 1 625 Single cylinder. Rolling-mill. Producer. 1 625 Single cylinder. Air compressor. Producer. 2 500 Single cylinder. Air compressor. Producer. 7 500 Single cylinder. Cement-mill driving Producer. Total, 28 engines ; 32,600 indicated horse-power. * Presented at the Joint Meeting of the Iron and Steel Institute and the American Institute of Mining Engineers, London, July, 1906, and here published under a mutual agreement between the Councils of the two Institutes.

Jan 1, 1907

By T. D. Murphy, G. V. Henderson

The element silicon, with its usual partner, oxygen, plays the same role relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO2) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO4 tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature's cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide Si02 (analogous to its congener carbon in CO and CO2); a tetrachloride SiCI4 (analogous to CC14); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117° to 200ºC but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures --such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert et al., 1973; Pecora, 1960). Pursuing its esthetic aspects, briefly, silica is well-represented among gem stones which, to qualify as such, must have the attributes of beauty, durability, and rarity (Jahns, 1983). As quartzose gems usually have but one or, at

Jan 1, 1983

By R. Norman Orava

The strain-mte behavior of. the tensile yielding and flow characteristics of arc-cast polycrystal-line molyhdenum of pidrity > 99.97 pct was investigated in the range 10-6 to 10-1 sec-1 at 243o, 293o, and 373oK for two grain sizes, 0.027 and 9.098 mm. For 0.998 mm, the strain-mte dependence of the lower yield stress can be described by a straight line of the jowl a, = a + 0 log e over the whole range of strain rates examined. However, for 0.027 mm, the data fit several consecutive linear relationships of the above form. The previous association of these different linear regions with different rate -controlling mechanisms is questionable for molyhdenzdm. The senlilog strain-rate dependence of the yield stress is consistent with Hahn's model for yielding when the stress dependence of the mobile dislocation density, pr, is taken into account. Since p', from rate -cycling experirnents, is found to be relatively insensitive to stress for single crystaIs, the obserzied log-log dependence of their yield stresses is also in agreement with the model. A correction for the stress dependence of p' changes the activation oolurrze for yielding from a zero to a more realislic inverse function of stress where the Peierls mechanism is believed to be rate-controlling. The gmin-size dependence of the lower yield stress is not a monotonic junction of strain rate. RECENT experimental evidence' has revealed that the strain-rate dependence of the tensile lower yield stress, a,, of commercially pure ni- obium and tantalum tested at room temperature can be described by several consecutive semilog relations of the form: sv =a + ß log € [1] where i is the applied strain rate and a and 0 are constant Over only relatively small ranges of strain rate. Three linear regions were found for niobium and four for tantalum. Each linear region was interpreted as being associated with a different rate-controlling mechanism on the basis of the current

Jan 1, 1964