Search Documents

W. M. CURSE, Mansfield, Ohio.-Outside of the commercial valu-ation of the material, for what purpose does this alloy-90 per cent. of copper, 6 ½ per cent. tin, 2 per cent. zinc, and 1 ½ per cent. Lead-seem to be eminently fitted? C. P. KARR.-So far as our tests go, it would be eminently fitted for steam valves and pistons, and for the work for which 88-10-2 bronze is generally used, although for very large castings it would not be superior to 88-8-4 bronze. P. E. MCKINNEY, * Washington, D. C.-Some time hack, clue to a desire to avoid some of the objectionable features of 88-10-2 bronze, particu-larly on heavy castings, also to save tin where possible, we took up the question of a substitute for 88-10-2 bronze, where red bronze was ordinarily specified. After trying most of the mixtures, we found that when using as low a tin content as is given in this proposed composi-

Jan 12, 1919

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2'4'5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.' Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By E. W. Cawthorne, R. I. Jaffee, C. M. Craighead

SOLUTION of a solid metal or alloy in a molten metal bath is used daily in melting operations, extractive metallurgical processes, and in brazing. It is generally recognized that temperature, time, agitation, and the composition of the solute metal and the solvent bath all affect solution rate. However, there is little information available in the literature on the kinetics of the process or the relative effect that these variables have on solution rate. In connection with an aluminum brazing study, data on the solution of aluminum in an A1-Si* bath to promote rapid solidification. The chemical analyses were made on drillings taken from the cast plates. The results of this work are listed in Table I. The thermal-analysis data were obtained on 200 gram samples cooled at approximately 1.5" per min. A calibrated chromel-alumel couple was used. The thermal arrests were recorded autographically on a General Electric photoelectric potentiometer recorder. The instrument was calibrated to 22.5 pct. The thermal emf was bucked with a Leeds and Northrup semiprecision potentiometer so that 1 mv represented the full scale of the GE recorder. Referring to Table I, it will be noted that the analytical results tend to be lower than the intended compositions by about 0.3 pct Si in the higher ranges. In view of the known difficulties in obtaining accurate silicon determinations by wet analysis when the silicon content is high and in view of the care that was employed in weighing and preparing the alloys, the intended compositions are believed to be more accurate than the analyses. Furthermore, when the thermal-arrest data are plotted against the intended compositions, a smooth curve is obtained, as shown in Fig. 1. This is not the case when the data are plotted against the analytical results. It will be noted from Table I that the 12.5 pct Si alloy (melt 4) showed a primary arrest at 577.6"C and the eutectic at 576.l°C. The metallographic examination of this chill-cast plate sample showed a small amount of primary silicon. These results, Fig. 1, place the eutectic at slightly less than 12.5 pct Si and are in rather good agreement with the unpublished Hanford data. In all of the subsequent work, the composition of the A1-Si dipping baths was determined by thermal analysis (spread between the primary arrest and the eutectic temperature) employing 12.5 pct Si and 577.2 °C as the composition and temperature of the eutectic. Material Preparation and Selection of the Techniques: At the beginning of this work, it was anticipated that, owing to oxide film present on the surface of the aluminum, difficulty would be encountered in obtaining rapid uniform wetting of aluminum specimens dipped in the A1-Si bath. The following etchants were investigated as possible methods of providing a thin uniform oxide film on the specimen surface: 1—phosphoric acid (H³O4), 2—fluoboric acid (HBFI), 3—sodium hydroxide (NaOH), and 4—hydrofluoric acid (HF). Tests with sheet .specimens (2x½x0.06 in.) of 2s aluminum prepared with these etchants indicated that the fast uniform wetting required for this work could not be obtained if any oxide film existed on the specimen surface. Tests were then conducted by dipping similar specimens etched in 5 pct NaOH and given a thin

Jan 1, 1956

By L. A. Roe, John Jan

Iodine is a soft, lustrous, grayish-black nonmetallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue-violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 25 and 35 million lb per year, of which about 30% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and seawater. According to the US Geological Survey, it is the 47th most abundant element in the earth's crust. The minerals lautarite, Ca (I03)3 (calcium iodate), and dietzeite, Cat (103)2 (CrO4), (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapaca provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in Table 1. Table 2 lists estimated world iodine reserves. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated reserves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable. Markets and Prices Iodine and its compounds are generally marketed in the form of: iodine, crude; iodine, resublimed; calcium iodates; calcium iodide; potassium iodide, sodium iodide, and numerous organic compounds. Product Specifications Crude iodine, World market: 99-99.5% 12. Crude iodine, US produced, average: 99.8% 12. Crude iodine, USP XVII Specs: not less than 99.8% percent I2. Resublimed iodine is usually 99.9% and ACS specifications call for not over 0.005% total bromine and 0.020% nonvolatile materials (Anon., 1971). Prices, c.i.f. United States, for iodine have been steadily increasing from $1.18 per lb of crude in 1967 to $6.37-7.27 in January 1981 (Anon., 1981). In 1980 the price of iodine increased by 50%.

Jan 1, 1983

By R. P. Smith

The carbon content of a number of alloys ranging (before carburitation) from purified iron to purified cobalt was determined for fixed activities of carbon by equilibration with each of six CO-CO2 atmosphere at 1000°C. At fixed carbon activity, the carbon content decreases continuously with increasing cobalt content. For concentrations of 0 to 50 at. pct Co the results can be expressed by a linear interaction equation of the type In y2 = 7.76n2/(n1+n3)+ 2.30 n3/(n1+n3) where y2 is the activity coefficient of carbon (standard state such that y2— 1 as n2 — 0 in the Fe-C binary) and n1, n2, and n3 are the number of atoms of iron, carbon, and cobalt per unit weight of alloy. The results are also given in terms of the a functions. In the same concentration range, the results are in accord with the regular solution theory of Alcock and Richardson. THE carbon content of Fe-Si, Fe-Mn, and Fe-Ni alloys at fixed activities of carbon has been reported previously.'-, The present work extends R. P. SMITH, Member AIME, is Research Chemist, E. C. Bain Laboratory for Fundamental Research, United States Steel Corp., Research Center, Monroeville, Pa. these measurements to a series of Fe-Co alloys. These alloys, like the Fe-Ni alloys, are fcc ("aus-tenitic") over the entire range of composition at 1000°C. EXPERIMENTAL PROCEDURE The alloys were made from electrolytic cobalt and Plast-Iron in a small vacuum-melting furnace. A small amount of graphite was added to each melt to keep the oxygen content low. The ingots were analyzed for iron and carbon: the amount of cobalt was obtained by difference. Analysis of the top and bottom of the ingots indicated that they were uniform in alloy content. Except for the pure cobalt the ingots were hot-rolled to approximately 0.15 cm thickness, cleaned by sandblasting, then cold-rolled to about 0.045 cm. We were not successful in cold rolling the pure cobalt; therefore it was hot-rolled to the final thickness. The last traces of surface oxide were removed by acid pickel, then the samples were treated in a hydrogen-2 pct water vapor mixture at 1100°C to remove carbon and most of the oxygen. The carburizing procedure was similar to that previously described.1,2,4 The alloys in the form of strips about 1.7 cm wide, 7.5 cm long, and 0.04 cm thick, together with a similar specimen of purified iron, were equilibrated with each of six CO-CO2 mixtures of fixed composition, then quenched in the

Jan 1, 1965

By M. E. Learmont, R. J. Lipp, I. Iwasaki

In the selective flocculation of iron ores, the concentration of alkaline earth ions in pulp solutions plays a critical role. Sodium silicate, alone or with sodium tripolyphosphate, has been used as a dispersant. When Ca+ + concentration exceeds 15 to 20 ppm, however, only a strong complexing agent, such as ethylenediaminetetraacetate (EDTA) was found to be effective (Heerema, Lipp, and Iwasaki, 1979). Some iron ores release Ca+ + in excess of 20 ppm. With ores that contain gypsum, the Ca+ + concentration may reach several hundred ppm. The purpose of this investigation was to compare the effectiveness of EDTA with nitrilotriacetate (NTA) in countering the adverse effects of Ca+ +, particularly at high Ca+ + concentrations. Emphasis was placed on the use of NTA since it is more cost-effective than EDTA. It is also used in detergents in some countries (Malaiyandi, Williams, and O'Grady, 1979). NTA, like EDTA, forms a soluble complex with Ca+ + with a 1:1 molar ratio. Its structure and the value of log Kca are given below together with EDTA (Shibata, 1963). [ ] For experimental materials, an equal weight mixture of Lac Jeannine hematite and a high-purity quartzite from Thompson, MN, both ground to - 30 µm (- 560 mesh) was used. Selective flocculation test conditions and procedures were identical to those used in previous investigations (Heerema, Lipp, and Iwasaki, 1979). The optimum level of starch addition for the above mixture was determined to be at 300 g/t (0.6 lb per st). Initially, a series of selective flocculation tests were performed on the mixture pulped with 10-3M CaC12 (40 ppm Ca + +) at pH 11. With no NTA present, flocculation of the entire suspension resulted. The selectivities achieved in tests with 90, 100, and 150% of the stoichiometric amount of NTA were virtually identical to each other and also to the selectivity of separation obtained in the absence of Ca+ + Such an observation could have been expected since Ca+ + concentrations up to a few ppm may be tolerated in selective flocculation (Krishnan and Iwasaki, 1982). A similar series of tests were performed at 10-2M CaC12 (400 ppm Ca+ +). The results are shown in Fig. 1 as grade¬recovery curves. For comparison, the results obtained in the absence of Ca++ are included. At 90% of the stoichiometric amount of NTA, a large enough concentration of uncomplexed Ca+ + was left in solution to cause indiscriminate flocculation. Note in this figure that NTA is capable of countering the adverse effect of Ca+ + even at this high concentration when it is used in excess of stoichiometric amounts. The free Ca+ + concentrations at 100 and 150% are calculated to be 2.5 and 0 ppm, respectively. [ ] The relative effectiveness of NTA and EDTA was then compared at 100% of the stoichiometric amount using 10-2M and 10-3M CaCI2 (Fig. 2). EDTA appears to be slightly more effective than NTA. The free Ca++ of 0.02 ppm in 10-2M CaC12 with EDTA compared to 2.5 ppm free Ca+ + with NTA might account for the difference. As evident, prohibitively high additions of EDTA and NTA were required to complex high concentrations of calcium ion. The use of both of these agents would result in the accumulation of complexed Ca+ + in recycle water.

Jan 1, 1985

Jan 1, 1949

For the convenience of members who may be traveling from place to place, the Secretary has compiled a list of libraries or other places in the United States and foreign countries where MINING AND METALLURGY or the Transactions may be consulted. This list will be sent to members if they so request.

Jan 1, 1925

Although Australia is the world's second biggest producer of iron ore, the last few years have not been easy for companies in Western Australia's Pilbara region (see map) where more than 90% of the nation's iron ore is produced. For at least two years, the industry has been plagued by dwindling markets abroad, production-crippling strikes at home, skyrocketing costs (well above the official 13% annual inflation rate), an acute shortage of investment capital, increasingly ferocious competition from foreign iron ore producers-and, as if all this weren't enough, by an over-valued currency that has caused incalculable damage not only to iron ore producers but to the entire mining industry of Australia. (This last problem was mitigated less than two months ago, on November 28, 1976, when the Australian dollar was devalued by a whopping 17 1/2%.)

Jan 1, 1977

By G. Gutierrez, D. A. Elgillani, M. C. Fuerstenau

The zero-points-of-charge of apatite, calcite, and fluorite are pH 6.4, 10.8, and 10.0, respectively. Scheelite is negatively charged above at least pH 3. In this article, the flotation responses of these minerals in the presence of potassium oleate and sodium silicate are described and compared with electrokinetic data. Colloidal silica appears to be the species principally responsible for calcite depression, while silicate anion is the species responsible for fluorite depression. Additions as high as 1 x 10-3 mole/liter silicate have no effect on the flotation responses of apatite and scheelite. Selective flotation of nonmetallic minerals is difficult to achieve with fatty acids or soaps by themselves. As a result, specific reagents are added to aid these separations, and one of the reagents commonly employed for this purpose is sodium silicate. Flotation separations of various calcium-bearing minerals such as fluorite from calcite1-3 and scheelite from calcite2,4 and apatite,2,5 for example, almost always involve the use of sodium silicate. The mechanisms by which sodium silicate functions as a depressant are still not understood, probably for a number of reasons. For one thing, the dissolution process of sodium silicate is complex, giving rise to a number of ionic and colloidal species.' Moreover, the type and concentration of these species depend on the ratio of Na2O to SiO2, the concentration of sodium silicate, and the pH of the system.' At the present time, it is not known which species, colloidal silica or silicate anion, is responsible for depression. If colloidal silica is the species that is adsorbing, then adsorption must occur by electrostatic attraction between the colloid and the mineral surface. Silicate anion, on the other hand, may adsorb either physically or chemically. The objective of this paper is to determine first the active species of sodium silicate and then the conditions under which this species will adsorb and function as a depressant. EXPERIMENTAL MATERIALS AND METHODS Pure samples of apatite (Durango), calcite (Iceland-spar), fluorite, and scheelite were used in this investigation. Pure potassium oleate was used as collector, while reagent-grade HC1 and KOH were employed for pH adjustment. The sodium silicates used were samples obtained from the Philadelphia Quartz Co. In one series of experiments, various sodium silicates containing different ratios of SiO2 to Na2O were added to calcite systems. These sodium silicates contained SiO2-to-Na2O ratios of 3.75 to 1, 3.22 to 1, 2.40 to 1, and 1.60 to 1. All other experiments were conducted with the sodium silicate containing the ratio of 3.22 to 1, which is the one that is normally used in industry. Flotation experiments were conducted with 21/2-g charges of 48 x 150-mesh material in conductivity water with an apparatus and technique described previously. Electrokinetic experiments were conducted with both a Zeta Meter and streaming potential apparatus. Particle size was 48 x 65 mesh for the streaming potential experiments. EXPERIMENTAL RESULTS The first series of experiments involved flotation of scheelite in the absence and presence of sodium silicate. As shown in Fig. 1, flotation response was not affected with even the relatively high addition of 1 x 10-3 mole per liter sodium silicate. Interestingly though, no flotation was effected below pH 6 with this collector addition. The responses of apatite to flotation under these same conditions are given in Fig. 2. Similarly, no depression was obtained in basic media under these conditions. Similar experiments were conducted with fluorite, and in this case, depression was noted above about pH 11 with 1 x 10-3 mole per liter sodium silicate (Fig. 3). When calcite was floated with these same levels of addition of sodium silicate, essentially no flotation was possible above pH 7 (Fig. 4). The effect of collector addition with a constant addition of sodium

Jan 1, 1969

By F. M. d’Heurle

Films of molybdenum have been prepared by sputtering onto oxidized silicon substrates. The resistivity. lattice parameter, orientation, and grain size were studied as a function of substrate temperature and substrate bias. Under normal sputtering conditions, the resistivity of the films was found to be quite high (600 x 10 ohm-crn). However, with the use of the negative substrate bias of 100 v and a substrate temperature of 350°C, films weve produced with a resistivity of ahout twice that of bulk molybdenum. The lattice parameters measured in a direction nornzal to the surface of the films weve found to be gveatev than the bulk value. This was interpreted as being at least partly due to the presence of compressive stresses. The effects of annealing in an Ar-H atmosphere were studied in terms of diffraction line width, lattice parameter, and resistivity. BECAUSE of its relatively low bulk resistivity (5.6 x 106 ohm-cm)' molybdenum is potentially interesting as a thin-film conductor in integrated circuits. An additional feature which makes it attractive for this purpose is its low coefficient of expansion (5.6 x KT6 per "c),' which is fairly well matched to that of silicon (3.2 x 10 per c). It is possible to deposit molybdenum films by evaporation but generally films produced in this manner have a high resistivity. In order to achieve resistivities close to bulk value, Holmwood and Glang found it necessary to operate in a vacuum of about 107 Torr and to maintain the substrates at 600 C during film deposition. Sputtered molybdenum films have been examined by Belser et a1.7 and, recently, by Glang et al.' This paper describes the results of an attempt to extend some of that work and examine the effects of annealing and getter sputtering on the physical and structural properties of the films produced. SPUTTERING APPARATUS AND PROCEDURE The apparatus used for most of the film sputtering work described here consisted of two "fingers" serving as anode and cathode, respectively, which were mounted within an 18-in.-diam glass chamber. A liquid nitrogen-trapped 6-in. diffusion-pump system was used to achieve a vacuum of about 1 x 107 Torr within the chamber prior to sputtering. The essential features of the equipment are shown in Fig. 1. Cathode and anode fingers are stainless-steel tubes isolated from the top and bottom plates by Teflon collars. In order to limit the discharge to the space between anode and cathode, each finger is surrounded by an aluminum hield, at ground potential, having an internal diameter 18 in. larger than the outside diameter of the finger. The cathode and anode fingers are 6 and 4 in. in diam, respectively. A 116-in.-thick sheet of molybdenum is brazed with a 10 pct Pd, 58 pct Ag, 32 pct Cu alloy to a copper disc which is mounted by means of screws and a large 0 ring onto the lower end of the cathode finger. The disc is cooled during sputtering by water circulation inside the finger. The use of several feet of plastic tubing for the water input and outputg reduces leakage to ground to less than 1 ma when the cathode potential is raised to 5 kv. The upper end of the anode finger is terminated by a brazed-on copper block. A variety of specimen holders can be easily mounted on the upper face of this block. Substrate heating or cooling is achieved by use of an appropriate unit attached to the lower face of the same block. Heating is achieved by means of cartridge-type heaters and cooling by copper coils fed with forming gas under pressure. The inner chamber of the specimen finger constitutes a small vacuum chamber of its own which is evacuated by an auxiliary mechanical pump in order to limit heating element oxidation and heat transfer by convection currents. An advantage of the finger arrangement is the absence of cooling and heating coils and wires within the main chamber. The stain less-steel shutter is useful to establish a discharge for cleaning the cathode at the beginning of each sputtering run. Water cooling of the shutter reduces heating and the out-gassing of impurities which might condense on the nearby substrates. Unless otherwise specified, the substrates used in these experiments were 1-in.-diam oxidized silicon wafe:s, 0.007 in. thick, having an oxide thickness of 6000A. The substrate holders were large copper discs onto the surface of which a number of molybdenum discs, 116 in. thick and 78 in. in diam, were brazed. The wafers were clamped to the molybdenum discs

Jan 1, 1967

By Jerry A. Selvaggi, Richard B. Jacob

The High Gradient Magnetic Separator (HGMS), also known as the High Gradient Magnetic Filter (HGMF), is an effective device utilized in magnetic separation. This method of separation is gaining popularity in the separation of submicron material containing feebly magnetics. The most common use of this type of separator is in the removal of iron stained particles to improve the brightness of kaolin clay. Potential areas for use of this magnet include: (1) desulfurization of coal (2) the clean-up of mill effluent (3) removal of fine particulate matter from municipal and indus¬trial waste (4) desulfurization of oil Design, operation, and applications of this separator are further dis¬cussed in papers by R. R. Oder (1975), and R. R. Oder and B. I. Horst (1975). This device is a system composed of an iron enclosure of high per¬mability material housing a set of electrical coils, a canister en¬closing a magnetic matrix (stainless steel wool), an electric power supply and a hydraulic system to maintain specified operating tempera¬ture conditions. See Figure 1.

Jan 1, 1984

By A. Gatti

Studies were made on the system iron plus alumina. Various methods of dispersing and various amounts of alumina were used. Powder metallurgy techniques were used to produce the final product. Microstructures and some mechanical properties are presented. Alloys containing up to 16 pct alumina by weight are ductile at all temperatures tested. The ivon-alumina materials have a higher yield stress and improved creep resistance over that of pure iron. SINCE the development of SAP' an A1- Al2O3 powder metallurgy product, great interest has been shown in the development of a SAP-like structure in metals and alloys other than aluminum. The outstanding properties of this class of materials are: 1) Good creep resistance at high temperature. 2) High yield strengths and high hardness at high temperatures. 3) High recrystallization temperature. However, the lack of ductility and formability has thus far limited the applications of SAP-like materials. The following report deals with methods of dispersing A12O3 in Fe, processing of powders into rod, structures produced after processing, and mechanical properties of the iron-alumina material produced. Methods of dispersing the alumina and also the volume fraction of alumina added were varied. MATERIAL Powder Processing— Four methods of obtaining dispersions of alumina in iron were studied. 1) Oxidation-reduction of a Fe + 8 pct Al alloy. .2) Coprecipitation of Fe(OH)3 + Al(OH)3 from aqueous solution. 3) Colloidal mixing of Fe,O3 and Al2O3. 4) Colloidal mixing of Fe powder and A1,O3. Fig. 1 is a processing flowsheet which outlines the processing steps taken to produce a final extruded bar 1/4 in. in diameter and about 30 in. long. The - 100 mesh iron-aluminum alloy was oxidized by placing a thin layer of powder on an alumina plaque. The reduction step was modified to include 1/2 hr at 1000°C since the powders tended to become pyro-phoric unless sintered slightly after low-temperature reduction. Compacting was done in a 1-1/8-in.-diam pressing die. The slugs produced averaged 1 in. in length. The billets were encased in low-carbon steel cans shown schematically in Fig. 2. The blank is included for structure and property comparison purposes. TESTING PROCEDURE All tests were made on as-extruded material.

Jan 1, 1960

Executive BENJAMIN B. THAYER, .Chairman. JAMES F. KEMP, CHARLES F. RAND, ALBERT R. LEDOUX, JOSEPH W. RICHARDS, Membership KARL EILERS, Chairman. W. R. INGALLS, JOHN H. JANEWAY, Jr., JOHN D. IRVING, SIDNEY J. JENNINGS. Finance CHARLES F. RAND, Chairman. KARL EILERS. W. L. SAUNDERS.

Jan 1, 1917

BROWN iron ore reserves of Franklin county are being proved economical by Heavy-Media separation at the Blackburn mine of the Shook & Fletcher Supply Co. about 120 miles north-west of Birmingham. The ore occurs under a cover of ferruginous chert and gravel and these materials are also disclosed as streaks in the ore body as it is mined. Previous methods of jigging and hand sorting the ore became too expensive because of rising wages but the use of Heavy-Media separation has proved economical and is making Franklin county the most promising source of additional reserves of brown ore.

Jan 12, 1950

By W. L. Crentz, E. E. Donath, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By E. E. Donath, W. L. Crentz, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

F. L. Clerc, Chicago, Ill. (communication to the Secretary): On page 681 in Mr. Winslow's paper, he refers to me as having "advocated the view that the ores were derived from the patches of Coal-

Jan 1, 1895

By K. Takahashi, I. Iwasaki

The methyl stretching vibrations for a series of normal xanthates, isoxanthates and normal amines were determined with the aid of an infrared spectro-photometer, and the results were compared with published information on the corresponding alcohols. The frequency shifts of methyl stretching vibrations may be attributed to the inductive effect of polar groups. The hydrogens in the shorter chain alkyl groups are somewhat polar and can be expected to interact with water molecules by hydrogen bonding. Contact angle, surface tension lowering, solubility, and critical micelle concentration appear to be related to the induced polarity of the alkyl groups. Traube's rule states that in homologous series of compounds solubility decreases and surface activity increases regularly with the size of the hydrocarbon group. Analyzing the work of transfer of a solute from solution to surface, Langmuir' interpreted this rule to mean that each CH2 group added to a molecule produced its effect independently of the others. It is also well known2 that the maximum equilibrium contact angle with sulfhydryl collectors is independent of the polar groups and of the sulfide minerals, and that it increases to a certain limit with the number of carbon atoms in the alkyl group. This observation is thought to demonstrate the orientation of the collector molecules at the sulfide surfaces. The dependence on the hydrocarbon chain length is usually explained as due to the screening of the force field of polar mineral surfaces.3-5 Here again, Langmuir's principle of independent surface action appears to be implied. Heteropolar compounds consist of nonpolar and polar groups, the former being the hydrocarbon group and the latter containing such electronegative atoms as O, N, S, P, or halogens. According to Palit6 the hydrogens in the alkyl groups are more electroposi- tive than in the paraffins owing to the negative inductive effect of the polar groups and a possibility that a hydrogen bond with water molecules ensues. Goto and Takenaka7 provided direct evidence of the inductive effect by measuring the shift of the C-H stretching vibrations of alcohols, acids, and alkyl bromides with an infrared spectrophotometer. Their approach appeared to be directly applicable to the studies of surface activity both at air-water and water-mineral interfaces encountered in flotation systems. The present article attempts to relate the C-H stretching vibrations of alkyl xanthates, alcohols, and amines with such flotation chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration. MATERIALS AND METHODS Normal xanthates from methyl to octyl inclusive and the isopropyl, isobutyl, and isoamyl xanthates used in this investigation were prepared in the usual manner.8 Normal amine hydrochlorides with carbon chain lengths of 1, 2, 4, and 6 were from Distillation Products Industries, of 8 from Archer-Daniels-Midland Co., and of 10, 12, 14 and 16 from Armour and Co. Normal propylamines, pentylamines and heptylamines from Distillation Products Industries were used both as received and as hydrochloride formed by converting the amines according to the procedure described by Li9 Perkin-Elmer Model 521 and 621 infrared spectro-photometers were used to investigate the spectra in the frequency region of 3050 to 2800 cm-' with frequency scale expansion. The accuracy of the frequency readings was within + 1 cm-1. The KBr micropellet technique was used to prepare the xan-thate samples for measurements, and the halocarbon mull technique was used for amines and amine hydrochlorides. EXPERIMENTAL RESULTS Fig. 1 shows the CH3 asymmetric stretching vibrations as a function of the number of carbons in the alkyl group for normal xanthates, isoxanthates and amines. Also included in the figure are data for normal alcohols and isoalcohols taken from the article

Jan 1, 1970

By W. J. Rogers, L. J. Dwiggins, R. O. Williams

THERE has been comparatively little work on the importance of strain rate and temperature as variables in the formation of deformation textures. For this reason the present work was started, the choice of compression being in part that of convenience and in part because of the absence of quantitative data in this area. These do not turn out to be important variables within the range studied which permits the results to be condensed into this note. Samples 1/4 in. in diam and 1/2 in. long were machined from 99.9 pct pure commercial aluminum and recrystallized to a fine grain size. A set of five samples were deformed between a spring-driven weight and an anvil resulting in roughly 20 pct strain each time. The strain rate varied because of decle-ration and shortening of the sample but would average about 10&apos; per min. Deformation at temperatures over the range of -76" to 150°C were obtained by heating or cooling the samples. Complete lubrication could be obtained by oil since the short time of contact did not permit its escape. The samples were compressed to a total true strain of 1.4 to 1.6. A larger sample was prepared similarly with spiral grooves in the ends to hold paraffin which provided essentially complete lubrication. This sam ple was compressed slowly at room temperature at a rate of about 2 per min to a total strain of 1.0. Cylindrical samples were carefully machined from these discs with a radial direction as an axis. They came from the center half of the samples and were roughly 1/16 in. in diam. The samples were etched down 15 pct to remove any surface effects. Diffraction data were then obtained for six different kinds of planes by the use of the Norton technique as applied to a fiber texture. Direct comparison between the raw data failed to reveal any significant difference between any of the samples and consequently the data from only one sample was completely reduced. The particular sample had been deformed at O°C The background was subtracted from the intensity data which were averaged over the four quadrants and then normalized to random. These data were then used to obtain fiber-axis distribution charts as previously described.2 For this sample the (422) plane was also run to assist in this inversion. The final result, Fig. 1, provided a comparable fit to that previously obtained from fiber data. About 85 pct of the material forms an elliptical texture around the <110> direction. The radius (at half height) is 5.5 deg along the (111) boundary and 8 deg along the (100) boundary. The remaining 15 pct forms a ridge running from this texture to near the <311> direction. The regions around the (100) and (111) planes are devoid of material. The earlier qualitative results of ~arrett~ are in complete agreement with the present results. The possibility has been dis-cused that the material around the <311> results from friction between the sample and compression plates.4 The present results are considered proof that such is not the case because of the uniformity of sample deformation and the requirement of axial symmetry before fiber-axis distribution charts can be accurately obtained. Recently results have been obtained to show that strain rate and temperature are important variables in the extrusion of aluminum.5 Perhaps the most important observation was that the partial recrystal-lization occurred even at room temperature. Strain rate was considered to be a factor only in that it produced a temperature change. There are many differences between the two experiments, the most important possibly being that their material was roughly ten times the purity of the present material. The present experiment, however, may not be as definitive as desired in this respect since it has been shown that compressed aluminum recrystallizes without a texture change6 although supplementary

Jan 1, 1961