Search Documents

By A. L., Bailey

All who are even generally aware of the tremendous rate of increase in coal washing operations must realize the growing importance of the float-and-sink test. I believe it is conservative to estimate that, in the past decade, the dollar volume of float-and-sink testing has increased tenfold. It is a simple matter of economy, then, to examine the factors that determine the cost of adequate float-and-sink testing. When the Coal Preparation Section of the Bureau of Mines entered upon a greatly expanded program of such work in connection with the synthetic liquid fuels investigations, it seemed advisable to examine these factors experimentally. The principal consideration that differentiates float-and-sink test sampling from general purpose sampling, is that the original particle size must be preserved. Therefore, the total cost of the test will be directly affected by any standard that might be proposed to limit sample bulk reduction at any given particle size. For this reason, the relationship of sample size to variability of results was the first factor to be studied experimentally.

Jan 1, 1949

By Klaus Schwerdtfeger, Hans-Jürgen Engell

Activities of silicon in Ni-Si melts have beelz determined in the temperature range 1480° to 1610°C from electromotive-force measurements involving the cells The data obtained are used to derive the activities of nickel and the integal free energies of mixing. Entropies of mixing are calculated from the free energies of mixing as obtained in the present study and the heats of mixing as available in the literature. ACTIVITIES in Fe-Si and Co-Si melts have been determined recently by the authors&apos; using galvanic cells consisting of alloy, an oxygen electrode, and an oxide melt as electrolyte. The present paper deals with activities in Ni-Si melts as measured with the same technique. A schematic diagram of the cell is shown in Fig. 1. The alloy and the electrolyte consisting of CaO and SiO2 are contained together in a silica-glass crucible. During the experiment the silica glass crystallizes to cristobalite on the surface of the crucible. Nickel contents of the electrolyte are very small (<0.1 pct as checked with chemical analysis), because of the noble character of nickel in comparison with silicon. A tapered silica tube is connected to the crucible through which a platinum or molybdenum wire is inserted, as shown in Fig. 1. A platinum tube reaches the surface of the CaO-SiO2 electrolyte from above. The platinum tube is provided with four holes on its side, through which oxygen of 1 atm pressure is blown over the electrolyte. The cell reaction is given by the equation Si(metal) + O2(gas) = SiO2(electrolyte) [3] and the galvanic electromotive force of the cell is given by the formula

Jan 1, 1965

By V. O. Struebing, K. A. Johnson, F. H. Ellinger, C. C. Land

The system Pu-Ce-(Pu,Ce)Co2 has been investigated by thermal, micrographic, and X-ray diffraction methods. The principal characteristics of this system were found to be: 1) a "eutectic" valley extending across the phase diagram from the 6 Pu/Pu3 Co eutectic at 408°C to the 7 Ce/Ce24Co11 eutectic at 42Z°C, the maximum temperature in the valley being 443°C; 2) three ternary inter mediate phases, each having an appreciable mutual solid solubility for plutonium and cerium; 3) eleven four-phase equilibria comprising one eutectic, four peritectics, and six Class II reactions; 4) a pseudobinary section between the ternary phase A and the y Ce solid solution, and another such section between the 6 Pu solid solution and the 77 phase (Pu3 CO) containing cerium in solid solution. ALLOYS of plutonium that are completely molten at temperatures in the vicinity of 500°C are of interest for use in the liquid state as fast reactor fuels. Since exploratory work1,2 on Pu-Ce-Co alloys had indicated that a "eutectic" valley extended across the ternary system between the Pu-co[6 Pu/n (Pu3co)] and the Ce-CO[? Ce/? (ce24co11)] binary eutectics, thus allowing alloys of any plutonium concentration to be selected within the temperature limitation, the present investigation was begun for the purpose of accurately defining the "eutectic" valley. However, when the existence of three ternary intermediate phases and the consequent complexity of the liquid-solid equilibria were discovered, the investigation was expanded to cover the complete system, except for the corner between the isomorphous series PuCo2-CeCo2 and pure cobalt. 1) EXPERIMENTAL The purities of the alloy components are given in Table I. Alloy buttons, each weighing about 5 g, were prepared by arc melting the accurately weighed components (±0.1 mg) under a purified He-Ar atmosphere. Weight loss as a result of melting was usually less than 1 part in 1000; therefore, the buttons were not chemically analyzed. One half of each button was re-melted by induction heating in vacuo in a magnesia crucible and furnace-cooled, so as to produce a somewhat coarser microstructure than that of the rapidly cooled arc-melted button. About 20 g of each alloy to be examined by thermal analysis were remelted in vacuo in a tantalum crucible of the inverted thermocouple well type. The thermal, X-ray diffraction, heat treating, and micrographic methods used in this investigation were essentially the same as have been described in earlier reports.3,4 Two etchants for these alloys were found to be satisfactory: A) 8 (parts by volume) orthophosphoric acid, 5 ethanol, and 5 glycol; B) 7 tetraphosphoric acid, 36 water, and 57 2-ethoxyethanol. Etchant A was used at 5 to 6 v for 15 to 20 sec, and etchant B was used at 10 v for 10 sec. 2) THE LIMITING BINARY SYSTEMS 2.1) Plutonium-Cerium. The phase relationships of this system have been investigated by Ellinger, Land, and Cramer,5 and by Selle and Etter.6 The over-all agreement of their phase diagrams is good, but there are some discrepancies in the positions of some phase

Jan 1, 1967

By E. Amott

A test is described in which the wellubility of porous rock is measured as a function of the displacement properties of the rock-water-oil system. Four displacemet operations are carried out: (I) sponlaneous displaceti?ent of water by oil, (2) forced displacement of water by oil oil in the same system using a centrifuging procetllrre, (3) spontaneous displacement of oil by water. and (4) forced displacment of oil by water. Ratios of the spontaneous displacement volumes to the total displucenlent volumes are used as wettability indicates. Cores having clean mineral surfaces (strongly preferentially water-wet) show displacement-by-waler ratios approaching 1.00 and displacement-by-oil ratios of zero. Cores which ([re. strongly preferentinlly oil-wet give the reverse resu1ts. Neutral wellability cores show zero values for both ratios Fresh cores from different oil reservoirs have shown wettabiltties in tlris te.st covering rrlti~ost 111e conlplrtt, range of thr: te.st. Notvever, nlo.s/ of tlle fresh California cores tested were slightly prcfere111icrlly wclter-\vet. The chrrnge.~ in coro u (&apos;liabilities, as indicated hy this te.st, r~.sril/ing from various CO~P hanrlling procedures tt,ere oh.served. In sonie ca.sc,s /Ire ~,cttahilitio.c. of fresh cores were changell by drxi:~g or 11y e.x/rclct ing with iolcreiii~ or. dioxunc~; in o/h~r cases they were 1101 changed. Co~ltrrc/ of cort,.s ~.ith filtrc~t~c. from water-base rlrilling rilrrrls crlrc.sed littlc change in we/ /ahility ivhile contnct with filtrates frorii oil-hus~ ri1rlcl.s tlecrrascrl the prefcrerlcc, of the, cores for )I.NI Usitig thi,s test to ri.crl~lute n~r~ttubili~y, N .vt~ldy was iilarle of /lie correlmtio~i of wettability with wa/erfloocl nil recovery for orttcrop Ohio sand.stone and for Al~ln-tlunl. Resul/.v indicate thml no single correlatioti between these factors applies to different porous rock syste~n. It is thought that diflerences in pore gen~netry resrrlt in diflrrerrce.~ in this correlurio~z. INTRODUCTTON Most investigators who have reported on the wettahility of porous rock have described such rock as prcferentially water-wet or preferentially oil-wet. In some cases a third classification, neutral wettability. has been used. The efficiency of water floods in each of these wettability groups has been described in numerous publications. Several methods for characterizing porous rock wet tability more precisely have been reported,&apos; " but it appears that because of one weakness or another. none of these has been generally accepted. Early in our studies in this field, it was found that the displacement efficiency of oil by water in a particular porous rock having a strong preference for water was quite different from that in a similar rock having only a moderate preference for water. Thus, there appeared to be a need for a practical, reasonably precise wet tability test. one which could classify porous rocks into 10 to 20 different groups rather than the two or three broad groups listed above. The test developed to meet this need is described in this paper. Also, changes in wettability, as indicated hy this test, resulting from various core handling procedures are discussed. Finally, data showing the corrclation of wettability with waterflood oil recovery for two different types of cores are presented and discussed. Some confusion has resulted from the failure of certain writers to define clearly some of the wettability terms they have used. Accordingly, the following commcnts concerning definitions are offered. The wc t ta-hility of a solid surface is the relative preference of that surface to be covered by one of the fluids under consideration. It is felt that this is the generally accepted definition. The fluids being considered must bc specified (or understood) before the term wettability has any significance. In the work reported here these fluids are water (3 per cent brine) and oil (kerosene). The term preferential wettability is sometimes used, but we think that the word preferential is redundant here and should not be used. Tn line with the definitions of Jennings&apos;, a preferentially oil-wet solid surface is regarded as a surface which will show an oil advancing contact angle less than 90" (measured through the oil) in the water-oil-solid system. Oil will spontaneously displace water, if both are at the same pressure, from such a surface. A preferentially water-wet surface is analogous. This is consistent with the wettability definition above. As Jennings has said, frequently the term oil-wet is used to mean the same thing as preferentially oil-wet. However, oil-wet also has been used occasionally referring to an oil-covered surface when the availability of water was limited. To avoid confusion from this source, we do not use the terms oil-wet and water-wet. DESCRIPTION OF WETTABTLITY TEST The following points were considered desirable in a wettability test for our purpose. 1. The test should be a displacement test resembling

By Sven Fornander

An account is given of the way in which a new process for desulphurization of hot metal is carried out at a Swedish blastfurnace plant. In the process powdered burnt lime is used as a desulphurizing agent in a rotary furnace. Results are given. IN a paper by Kalling et al.* the fundamentals of a new process for desulphurization of hot metal using powdered burnt lime as a desulphurizing agent were outlined. The purpose of the present paper is to give a brief account of the way in which this process is being carried out in practice by Surahammars Bruks AB, Sweden, and of the results obtained. + The hot metal from the blast furnace is tapped into a ladle of 15 tons capacity and transferred to a rotary furnace, a simplified drawing of which is given in Fig. 1. The rotary furnace has a total length of about 160 in. and an outside diameter of the rings of about 130 in. The furnace is in a horizontal position, with its rings placed on four rollers, and can be rotated by a driving mechanism at various speeds of up to 34 rpm. The rotary furnace and its driving mechanism were designed and constructed at Surahammar. The hot metal is charged into the rotary furnace through the opening to the left in Fig. 1. See Fig. 2. An addition is then made to the furnace consisting of finely ground burnt lime amounting to 2 pct of the weight of the hot metal as well as 0.5 pct of coke breeze. After the additions are made, the furnace is sealed to the atmosphere by means of two lids and set in rotary motion at a rate of 34 rpm. The sulphur in the hot metal is rapidly absorbed by the lime added, the time of treatment needed is normally 30 min. The process is then stopped, the lid is removed, and the furnace is lifted up by a crane and used as a tilting ladle for pouring the metal into the pig-iron molds, Fig. 3. Process Metallurgy The hot metal charged into the rotary furnace has a composition which usually lies within the following limits: C, 3.70 to 4.10 pct; Si, 0.80 to 1.80; Mn, 0.40 to 0.80; P, 0.025 to 0.030; and S, 0.060 to 0.200. Figs. 4 and 5 give examples of the changes in hot metal composition taking place during the treatment in the rotary furnace. As will be seen from the diagrams, the sulphur content of the metal decreases very rapidly during the first 10 min of treatment from about 0.100 to about 0.020 pct S. During the following 20 min, the sulphur content goes down slowly to about 0.005 pct S. The carbon and silicon contents of the metal decrease by about 0.10 pct each during the treatment. The manganese and phosphorus contents remain unchanged. Thus, if the process is started with an iron of the composition given above, the finishing composition of the metal usually lies within the following limits: C, 3.60 to 4.00 pct; Si, 0.70 to 1.70; Mn, 0.40 to 0.80; P, 0.025 to 0.030; and S, 0.002 to 0.020. The chemical reaction taking place during the process can be written:

Jan 1, 1952

By F. E. Gregory

MINING methods and customs in many districts of England are to this day strangely bound about by the records and traditions of the past. In some mining fields this is more apparent than in others, yet it is everywhere in evidence, for Cornwall with her mines under the sea, Wales with her famous quartzites, and Derbyshire with her remarkable cavern deposits, are all tinctured with quaint customs that have come out of the almost forgotten past. Here, modernism has never replaced tradition, and many of the laws are woven of the woof and warp of ancient custom. Indeed, these things exist because they have come to be part and parcel of the civil laws. And these laws are observed with meticulous care and accorded all the reverence due their venerable age. All activities pertaining to the mining of metals are hedged around by curious and ofttimes clumsy laws, each minute and trivial detail being covered by the civil code, and each petty law enforced by an ofttimes pompous official.

Jan 1, 1933

South Dakota State School of Mines, Rapid City, S. D. C C O&apos;Harris,-President. A number of technical bulletins have been issued at the South Dakota State School of Mines but, unfortunately, most of them are out of print and as this directory is concerned only with available publications, the following are all that are now to be had Bulletin 11, A bibliography of the geology and mining interests of the Black Hills region (1917), no charge; 14, The geology, mineralogy, and scenic features of Custer State Park (1926), 40 cents plus postage on 1 lb ; 15, The Tertiary mineralization of the northern Black Hills (1927), charge, postage on 1 1b.; 16, The mineral wealth of the Black Hills t418 pages) (1929), 80 cents plus postage on 3 lb

Jan 1, 1933

By Harold V. Pearce

THE plant of the Boston and Colorado Smelting Company, at Argo, Colo., has not received special notice in technical or scientific publications for some time past. Dr. Peters&apos; described the development of the reverberatory furnace used at Argo, but he dealt almost exclusively with the increase in size and the corresponding gain in capacity. Since the time of his description the changed conditions have led to a modification of the former smelting practice, and this modification forms the basis of the present paper. No claim is made for personal originality in connection with these improvements, in fact, I expressly disclaim any such intention, since nearly every successful step in the development of the process now used at Argo has been suggested by Dr. Richard Pearce at various times during the past 12 years, though perhaps in a different manner of exe¬cution. These changes would undoubtedly have been made before, were it not that many problems of greater metallurgical importance and momentarily of more urgent need thus had to be solved. At the time to which I refer, economic conditions demanded mainly an increase of capacity. Moreover, the determination and placing of exact losses in smelting were not so imperative as they now are. About three years ago, the time of my appointment to the - management of. the works of the Boston and Colorado Smelting Co., the great decline in the price of copper occurred; the Argo plant, in common with all others engaged in the copper-industry, lost heavily in the market-value of the stocks on hand of ore and furnace-products. Added to this was the unfortunate circumstance that the copper-supply of the Argo plant from general sources began to dwindle; in fact, it almost entirely ceased. About this time the smelting-plants in the west-

Mar 1, 1905

By THOMAS G. FEAR

THE COAL DIVISION started its share of the annual meeting Monday morning with a study of coal classi fication. A. C. Fieldner was in the chair. The report of the tellers of the ballot for division chairman, stating that Thomas G. Fear had been elected to that office, was read by M. D. Cooper. Mr. Fear acknowledged the honor in a few words. In reviewing the history of the Coal Classification Committee the chairman pointed out that this was its third symposium, the last previous one having been held at the 1930 Annual Meeting. Throughout its work the com¬mittee has had the active cooperation of the Canadian workers who are interested in the subject which should result in a uniform scheme of classification in Canada and the United States. F. E. Lathe, of the National Research Council, Ottawa, abstracted the first two papers of the session entitled "Determination of the Alkali-Soluble Ulmins in Coal," by Edgar Stansfield and K. C. Gilbart, and "Moisture Determination for Coal Classification," by the same authors. The third paper "Condition of Water in Coals of Various Ranks"&apos; was presented by its author, A. W. Gauger. Written discussions of these papers were presented by H. C. Porter and Gilbert H. Cady. In the oral discussion which followed, W. T. Thom, Jr., brought out the advisability of considering age as a factor in classification. Mr. Fieldner favored retaining bed moisture as a partial classification basis, stating that a review of many coal analyses revealed a remarkable consistency in this item in samples from a given mine particularly where the moisture content was not high. Mr. Porter pointed out that the structure and porosity of coal often have much to do with its moisture content and that these vary in different parts of a seam, particularly in anthracite. Mr. Gauger expressed doubt as to whether the Stansfield method gives the true moisture content of coal, which is needed for classification purposes.

Jan 1, 1932

By Bruno V. Nordberg

The high cost of coal in Butte and the development of large amounts of cheap electric power from the Missouri river caused the Anaconda Copper Mining Co. in 1908 to make an investigation as to the possibility of adapt- ing this cheap electric power for the operation of their many large hoisting plants. At this time electric power had already been adopted for practically all other power purposes around the mines, such as pumping, compressing air, etc. The map (Fig. 1) shows the location of the mines of the Butte mining district. These mines are located within a circle of approximately a 1-mile

Jan 1, 1914

By L. R. Plitt, M. K. Kim

The collecting properties of the fatty acid type collectors for barite were studied using zeta potential measurements, infrared spectroscopy, and Hallimond tube flotation tests. Based upon the experimental results, an adsorption model has been formulated which emphasizes the predominant role of the hydrocarbon chain in collector adsorption.

Jan 1, 1975

By C. W. Haworth, M. G. Hall

THE diffusion of copper in silver has been studied by Sawatzky and Jaumot1 and Cahoon and Youdelis.2 Sawatzky and Jaumot measured tracer diffusion in single crystal specimens but the 12.9 h half-life of CU64 limited the time of the diffusion anneal to about 50 hr, and in consequence the minimum temperature of the investigation was 716°C. Cahoon and Youdelis employed polycrystalline diffusion couples, and measured the interdiffusion coefficient over the range 0 to 2 at. pct Cu. These experiments were performed at temperatures down to 630°C and a discontinuity in the Arrhenius plot was observed at -700°C. The high D-values at lower temperatures were attributed to the effect of grain boundary diffusion. The present experiments were undertaken to investigate this anomaly and study the low temperature region of the diffusion of copper in silver. The method employed single crystal samples and a plated source of copper. Silver single crystals 2½ by 4 in. sq were grown from zone-refined silver bar (>99.99 pct Ag) by the Bridgeman technique, and $ in. thick slices were cut by spark machining. The specimens were electro-polished, and a 2 µm layer of copper was electroplated on to the planar surface at one end of each specimen using a potentiostatic voltage source. The following solution was used for plating: CuSO4 . 5H2O 125 gm H2SO4 (S.G. 1.8) 53 ml H2O 1000 ml The diffusion couples were sealed in capsules, in an argon atmosphere, and were annealed at either 701, 597, or 498°C. The temperature measurements were made to an accuracy of *l°C After the anneal, the penetration of copper into the silver was determined using an electron probe micro-analyzer. 100 sec scaler measurements of the intensity of Cu Ka! X-radiation were performed at 2 to 5 µm intervals along a line normal to the source, with a beam potential of 25 kv. Allowances were made for the background radiation, and the dead-time of the counting system in the normal way, and the intensity ratios were corrected to weight concentration by the method of Duncumb & de-Casa.3 For the analysis of the diffusion profiles, it was first observed that the copper layer did not completely dissolve in the host crystal for the specimens annealed at 498 and 591 whereas for the specimen annealed at 701°C, a single phase solid solution was formed. For the 498" and 597°C specimens, the concentration of copper in the silver at the interface was therefore constant throughout the anneal and the analysis for a

Jan 1, 1970

By E. D. Peters

It frequently occurs in the establishment of reduction works, in an entirely new and untried mining district, that the metallurgist in charge finds considerable difficulty in determining the process best adapted to the ores which he receives for treatment. At the first glance it would seem easy enough to decide what style of furnace is best adapted for beneficiating any one class of minerals. If the ore possessed a quartzose gangue and was comparatively free from base metals, while salt could be obtained at a reasonable price, one would naturally resort to a chloridizing roasting, and pan or barrel amalgamation for the extraction of its silver contents. If galena or carbonate of lead was the prevailing mineral, and charcoal could be obtained at moderate figures, the blast-furnace would beneficiate the ores most advantageously. But if, as is usually the case in Colorado, the ores consisted of an intimate mixture of galena, zinc-blende, copper-pyrites, and noble silver minerals, associated with an overwhelming mass of siliceous heavy spar, or limestone gangue, the common reverberatory furnace can be used to the greatest advantage ; and, although the product is only a copper matte, I do not hesitate to affirm that it can be treated, and the silver, gold, and copper produced at nearly the same price for which silver and lead can be separated. In Germany, blast-furnaces are frequently used for this same purpose, both for argentiferous and non-argeutiferous copper ores; but any one who will take the trouble to examine the statistics of smelting at Fahlun, the Oberharz, and other Continental works of this description, will see that the expenses are far too great, and the production much too small to think of employing this method in our mining districts, where only the softest and most miserable kind of charcoal is obtainable. I propose in this paper to give an accurate account of the expenses incurred at the Mount Lincoln Smelting Works in treating the same kind of ore, and producing the same end-product in both blast and reverberatory furnaces. I have taken for comparison a favorable campaign of the blast-furnace, and a good average month&apos;s running of the reverberatory. In the blast-furnace estimate I have included the calcining and concentration of the matte produced during that campaign, as I always, when possible, concentrated the regulus made

By C. E. Morris, S. R. Pollack

Current -vo1tage -temperature characteristics were studied for Al-A12O3-Al, Au structures. The oxide film was grown by gaseous oxidation in an 0, glow discharge. The electron-transfer mechanism was identified as tunneling and the barrier heights and thickness were determined. It was found that the barrier height at the parent aluminum-oxide interface is 1.5 ev and the built-in vloltage with an aluminum counter electrode is 0.35 v. The growth mechanism of the oxide is also discussed and it is suggested that Mott&apos;s theory is not applicable in describing the growth. Discrepancies were observed in the detailed comparison of tunneling theory, based on a trapezoidal model, with the data, and several possible explanations are discussed. THEORETICAL analyses of electron tunneling from one nonsuperconducting metal to another through an extremely thin insulating film have been presented.1-6 These calculations relate the current density, J, to the voltage, V, between the two metals, and to the temperature, T. The results of these calculations indicate that the magnitude of J and the detailed shape of the J-V characteristic will in general depend most strongly upon such properties of the insulating film as the thickness, the dielectric constant, and the structure of the electron energy barrier profile. The experimental results of many7-11 workers have corroborated the main features of these calcu- lations and have in fact been used to determine properties of the thin insulating film. It has been demonstrated, for example, that the tunneling current formulation of simmons4 is adequate to describe the observed J-V characteristic over approximately 10 orders of magnitude of current. Furthermore, from these observations and analyses, insight into the nature of the A1-A12O3 (thermally grown) interface region has been obtained.&apos;&apos; The temperature dependence of the tunnel current has also been studied and, although a self-consistent set of tunneling parameters can be chosen to describe these data at low voltages (i.e., <0.5 v), the tunneling parameters are different from those obtained from higher voltage (i.e., of the order of 1 to 5 v) measurements." We have measured the effect of temperature and voltage upon the tunnel current at higher applied voltages and find that the theory is inadequate to describe all of the effects reported here. A discussion of the origin of this inadequacy is presented following a description of the samples used for these experiments, and the experimental results. SAMPLE PREPARATION Metal-insulator-metal structures were fabricated in the following way. A 99.999 pct A1 charge was used to deposit, in vacuo, thirty films, 2000Å thick, onto a 1 by 2 in. glass substrate (7059 Corning glass). Prior to deposition the substrate was glow-discharged for final cleanup and then baked at 200°C for 2 hr at a pressure of 5 x 10-7 torr. The pressure during deposition of the metal films was 2 X 10-6 torr and the deposition rate was 50 to 100Å per

Jan 1, 1965

By B. Bernstrom

A 22-ft diam, 7-ft long, wet autogenous grinding mill was installed in the new Cretaceous plant of the Jones & Laughlin Steel Corp. to prepare crude iron ore for concentration in spirals and flotation cells. The paper describes the flowsheet and gives a description of the operating and metallurgical results that have been obtained. These results include capacity, horsepower, operating problems and a comparison of pilot plant results with those obtained in commercial operation. The Cretaceous plant at the Hill Annex mine of the Jones & Laughlin Steel Corp. was designed with a wet autogenous mill for grinding low grade iron ore so that it could be concentrated by spirals and flotation cells. The plant, on the west end of the Minnesota&apos;s Mesabi Range, went into operation in June 1961, and preliminary operating and metallurgical information describing the performance of this mill can now be given. The crude is lean ore from the Cretaceous iron foundation. This formation is a beach deposit of Cretaceous age that overlies the Precambrian direct shipping and concentrating ores. This rock in nature is not extremely hard but is quite resilient, resisting blasting in mining and size reduction in milling. It contains hematite as water-rounded particles and other fragments of the underlying iron formation and adjacent rocks cemented together by a high alumina-silica ferruginous matrix. It is interspersed with hard dense hematite agglomerates and also contains granite pebbles and boulders that were not cleaned off during removal of the surface. It has a 3.48 sp gr and in the stockpile the material consists of frag-

Jan 1, 1962

By Glenn A. Marsh, George Bernard

It is often assumed that aerated oil field brines which are to be injected underground contain dissolved oxygen in amounts which will cause appreciable corrosion. Through the use of a new portable dissolved oxygen meter, accurate determinations were made at three brine conditioning plants. At two older plants, dissolved oxygen concentration in the final treated brine was found to he almost zero In spite of aeration during the conditioning process. At a new plant, dissolved oxygen was initially present but disappeared soon after the brine was "inoculated" with oxygen-free brine from one of the other plants. Corrosion tests at the two older plants have substantiated predictions that the brines would lint be corrosive. These results show that mechanical deaeration may not always be required in brine treating plants. INTRODUCTION The present work was undertaken to add to our knowledge of aeration and deaeration of oil field brines in brine conditioning plants. It is commonly assumed that brines which are exposed to the air soon become more or less saturated with dissolved oxygen. Since oxygen-containing brines are known to be corrosive, precautions are often taken to keep air out of brine through the use of closed systems or mechanical deaeration. The study of oxygen in brine has been seriously hampered in the past because of the lack of a suitable analytical tool. The standard Winkler method for the determination of dis-solved oxygen is satisfactory for use in fresh water, but not in many oil field brines. Corrections have to be made for a number of reducing substances such as ferrous iron and hydrogen sulfide which are commonly present in natural brines. Very often the correction factors are much greater in magnitude than the amounts of oxygen which are to be determined, and consequently erroneous results are obtained. Also. erratic Winkler data are obtained when appreciable concentrations of calcium and magnesium salts are present. The first step in carrying out a systematic study involved designing a portable dissolved oxygen apparatus which would operate in natural brines. Subsequently, this apparatus was used in three brine conditioning plants. Dissolved oxygen data obtained here, and certain corrosion rate data, illustrate the interesting behavior of oxygen in these oil field brines. APPARATUS A portable dissolved oxygen meter described in detail elsewhere,&apos; was developed specifically for use with oil field brines. It is a polarographic apparatus employing a small rotating platinum electrode (cathode) and calomel reference electrode (anode). A potential of 0.7 volts is applied across the electrodes while they are immersed in the brine to be tested. 4References given at end of paper.

Jan 1, 1952

By M. E. de Morton

Low frequency-internal friction measurements on annealed chromium have shown a marked increase in damping below - 40°C which is strongly strain amplitude dependent. An interpretation of these results is given in terms of the motion of antiferromagnetic domains assumed to exist below - 40°C. A time effect on internal friction was measured after slight overstraining. After heavy deformation a pemzanent, five-fold increase in internal friction was observed at -45°C and the character of the internal friction us temperature curve markedly changed. Full recovery of damping was not attained until after heating to 800°C. A qualitative interpretation of some of these effects is given. THE aim of this preliminary investigation was to study the internal-friction characteristics of chromium containing comparatively small quantities of interstitial solutes in the fully annealed and heavily worked condition. Marked anomalies in a number of physical properties of chromium at temperatures near 40°C have been observed1 and an investigation by neutron diffraction&apos; has shown that chromium at room teyperature is weakly antiferromagnetic with a Nee1 temperature at approximately 200oC. No irregularities in the degree of antiferromagnetic ordering have been observed at -40°C, the transition temperature, and a complete explanation of this transition in chromium is still awaited. Recently weiss3 has suggested that an ordering effect of nitrogen in the face-centered interstices of the bcc lattice of chromium could be responsible for the superlattice detected below 200 °C in the neutron diffraction experiments. EXPERIMENTAL MATERIAL AND METHOD Specimens 10 by 0.030 in. diam were prepared from ingots of arc-melted electro-deposited chro-

Jan 1, 1961

By J. G. LECKIE

During the first ten months of 1943 copper was produced at a higher rate than in 1947. However, on Oct. 24 one of the large mines was shut down due to a strike. As of Dec. 31 the strike was still in effect and had already resulted in a loss of production of 50,000 tons of copper. The demand for copper was considerably greater throughout the year than the supply. The price of electrolytic copper delivered at the Atlantic Seaboard refineries advanced from 21.20 to 23.20 cents per lb during the year. This sustained demand for copper, together with the increase in price, has had the natural effect of spurring interest in uncovering new deposits, and in re-examination of known low-grade deposits and old tailing clumps. This is in addition to the usual reevaluation activities which normally result from the constant improvements in efficiency of ore concentration.

Jan 1, 1949

By C. W. Nicolson

THE Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less.

Jan 1, 1938

By Edwin B. Johnson

The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but no appreciable tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962.

Jan 3, 1963