Search Documents

By Richard O. Carlson

Ions of p31 and B 11 were implanted in natural insulating diamond macles. The thin (-0.4µ) layers showed sheet resistances of 107 to 1011 ohm per sq and activation energies of 0.17 to 0.34 ev above room temperature. However, no Hall effect could be measured, indicating that mobilities were less than I to 10 sq cm per (v-sec). Such low mobilities may be due to excessive scattering due to radiation damage in the bombarded layer or to very high concentrations of active compensating impurities. Annealing did not materially change the room -temperature properties, but the temperature was limited to -800°C by surface graphitization, the latter process probably being accelerated by lattice damage in our diamonds arising from the ion bombardment. A weak n-type thermoelectric power was detected after p31 irradiation, but it cannot be presumed that we have made the phosphorus ions active as donors in diamond. The natural diamonds have a high and uncontrolled concentration of impurities and, when coupled with the radiation damage and graphitization problems, would appear to seriously limit the quality of semiconductor that we can presently achieve by ion implantation in diamond. ALTHOUGH diamonds are usually thought of as insulating in terms of their electrical conductivity, it was found about 15 years ago that natural semiconducting diamonds do occur rarely, and these were designated as type IIb diamonds. These p-type semiconducting diamonds were found to be dominated by an impurity level 0.37 ev from the valence band. Evidence today based on correlation of the concentration of acceptor states from Hall effect measurements with the impurity concentrations determined by neutron activation analysis point to aluminum as the dominant acceptor impurity.' The compensating donor is believed to be nitrogen, which has a donor level 1.6 ev above the valence band.' However, only a small fraction of the total nitrogen content in the diamond is electrically active. An infrared absorption band at 7.8 p and ultraviolet absorption near 4 ev have been associated with nitrogen, the former providing a quantitative measure of nitrogen content.3 The nitrogen content is -l020 cm-3 in insulating or type I diamonds, but is less than 10'' in natural semiconducting diamonds. Much of this nitrogen is distributed in platelets oriented in (100) planes and not atomically dispersed in the diamond lattice.4 Semiconducting diamonds have been deliberately formed by incorporating impurities into the graphite charge in the high-pressure apparatus used to form diamonds.5 These manufactured semiconducting diamonds are always p-type, and while some show the 0.37 ev level due to aluminum, most such samples have been ascribed to impurity banding effects.6 The best natural or manufactured semiconducting diamonds have hole mobilities near 1500 sq cm per (v-sec) at room temperature, and those with the 0.37-ev level can be analyzed to reveal an acceptor concentration of 3 to 8 X 1016 cm-3 and a donor concentration 3 to 10 times lower.' NO bulk n-type diamonds have ever been reported, but the electron mobility has been measured as 1900 sq cm per (v-sec) by irradiating a diamond with ultraviolet to excite electrons out of the deep nitrogen donor level or other levels.7 New hope for the formation of n-type diamond has emerged from the ion-implantation method whereby desired impurities are introduced into a crystal lattice by bombardment with a high-energy beam of the impurity ion. It was found in the case of silicon that the usual donors such as phosphorus and arsenic and acceptors such as boron and gallium could be implanted into silicon. Wentorf and arrow' produced semiconducting layers on diamonds by an ionic bombardment in a glow discharge at potentials of about 2 kv. The observed typeness from thermoelectric probing seemed to depend on the atmosphere gas (nitrogen, argon, or hydrogen) rather than on the electrode material, but the nature of the conduction process in the thin damaged surface layer is completely unknown. A Russian group under Vavilov has attempted high-energy ion implantation in natural diamonds using boron and lithium ions9 and later also phosphorus, aluminum, and carbon ions.10 Their papers claim n-type layers from lithium, phosphorus, and carbon implant and a p-type layer from boron and aluminum implant, though the methods of type determination are not described in detail. Under government contract support, the Ion Physics Corp. has studied ion implantation in several semiconductors. While the bulk of their study1' was devoted to the irradiation of silicon, they did carry out a short study on boron and phosphorus implantation into natural diamonds. They did observe surface conducting layers but did not determine the typeness of the layers. For our experiments, phosphorus and boron were chosen as the dopant ions because of their respective donor and acceptor behavior in germanium and silicon. Moreover, they are the lightest mass dopants of the shallow level donors and acceptors from columns 111 and V of the Periodic Table (excluding nitrogen which is already present in diamond), and will have the largest depth penetration into the diamond lattice. EXPERIMENTAL Diamonds. As the target diamonds for our ion implantation study, we chose commercially available macles, which are flat, twinned diamond crystals. By scanning through the stock of a wholesale distributor

Jan 1, 1970

By F. H. Kihlstedt

The Larap iron deposits, 125 miles east of Manila, are the biggest high-grade iron deposits in the Philippines, and have in seven years produced nearly 4 million tons of 60 per cent ore. Magnetic surveying followed by churn and diamond drilling cheaply developed a score of million tons. The ore zone is a wedge of metamorphic rocks in fresh, Miocene sediments overlain by agglomerates, which seem to have filled a river valley eroded in the sediments. A mild overthrust of the competent agglomerates crumbled the shale in front. Solutions gradually turned it into more competent hornfels and deposited pyrite, then magnetite and pyrite in the pores. As the temperature rose large bodies of magnetite with some pyrite were deposited by replacement and in open cavities in tensional areas of overthrust shears. At still higher temperature magnetite and calcium-magnesium silicates formed other bodies in similar cavities, and finally the thrust zone was invaded by syenite porphyry, causing high-temperature alteration products. Possibly, as temperature abated, more high-grade ore was deposited. The complicated faulting indicates dynamic, chronological and spatial changes of mineralization rather than zoning in a static system. Noncommercial copper, molybdenum and some gold accompanied the iron mineralization. In the thirties the Philippines gained a justified reputation as a country of considerable mineral wealth. Traces of Chinese workings show that these earliest travelers and traders had in a small way exploited the latent gold resources in the Islands. The Spaniards continued this for centuries, but did not succeed in establishing any steady mining industry. Modern technology was required to get it started. The rapid development in the last decade before the war got its impetus from several financial factors, the return to sugar growers of previously collected taxes, the influx of Spanish capital during the civil war in Spain, the influx of Chinese capital when the Japanese started their "China incident," and others. Directly or indirectly much of this capital reached the mining industry; in particular, gold mining. Out of the turmoil of an exceptional mining boom emerged a sufficient number of good and well managed gold properties to send the production to a level above that of any single state in the United States at the time. Other ore deposits besides those of gold also received their share, and for a country without any heavy industries at

Jan 1, 1949

By F. H. Kihlstedt

The Larap iron deposits, 125 miles east of Manila, are the biggest high-grade iron deposits in the Philippines, and have in seven years produced nearly 4 million tons of 60 per cent ore. Magnetic surveying followed by churn and diamond drilling cheaply developed a score of million tons. The ore zone is a wedge of metamorphic rocks in fresh, Miocene sediments overlain by agglomerates, which seem to have filled a river valley eroded in the sediments. A mild overthrust of the competent agglomerates crumbled the shale in front. Solutions gradually turned it into more competent hornfels and deposited pyrite, then magnetite and pyrite in the pores. As the temperature rose large bodies of magnetite with some pyrite were deposited by replacement and in open cavities in tensional areas of overthrust shears. At still higher temperature magnetite and calcium-magnesium silicates formed other bodies in similar cavities, and finally the thrust zone was invaded by syenite porphyry, causing high-temperature alteration products. Possibly, as temperature abated, more high-grade ore was deposited. The complicated faulting indicates dynamic, chronological and spatial changes of mineralization rather than zoning in a static system. Noncommercial copper, molybdenum and some gold accompanied the iron mineralization. In the thirties the Philippines gained a justified reputation as a country of considerable mineral wealth. Traces of Chinese workings show that these earliest travelers and traders had in a small way exploited the latent gold resources in the Islands. The Spaniards continued this for centuries, but did not succeed in establishing any steady mining industry. Modern technology was required to get it started. The rapid development in the last decade before the war got its impetus from several financial factors, the return to sugar growers of previously collected taxes, the influx of Spanish capital during the civil war in Spain, the influx of Chinese capital when the Japanese started their "China incident," and others. Directly or indirectly much of this capital reached the mining industry; in particular, gold mining. Out of the turmoil of an exceptional mining boom emerged a sufficient number of good and well managed gold properties to send the production to a level above that of any single state in the United States at the time. Other ore deposits besides those of gold also received their share, and for a country without any heavy industries at

Jan 1, 1949

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles.

Jan 8, 1960

By C. S. Barrett

THE crystal imperfections known as faults in stacking (stacking disorder) are of importance to both fundamental and applied science and are receiving increasing attention. On the theoretical side there have been recent advances in the analysis of diffraction patterns in terms of stacking faults, and on the experimental side it has been found that certain metals develop a faulted structure on cooling through a phase transformation. Beyond this, little is known of what may be called the physical and mechanical metallurgy of faulting, although there has been no lack of discussion and conjecture as to the presence of faults in metals and the effect of faults on mechanical properties and microstructures. In the close-packed metals the nature of faults can be described very simply. Face-centered cubic (FCC) crystals consist of close-packed layers of atoms, (111) planes, stacked above each other in a definite manner. If one layer is designated as the A layer, the next must be a B or a C layer; that is, every atom of the second layer lies not above the atoms of the A layer, but nestles in the hollows between these, using the hollows designated as the B positions, or the equivalent hollows designated as C. If the sequence of layers is ABCABC...., so that layers three spacings apart are directly over each other, the crystal is FCC; if CBACBA ... it is an FCC crystal that is a twin of the former; if ABAB........or BCBC..it is hexagonal close-packed (HCP). A fault is a break in the sequence, such as ABCABABC .. . which has the effect of inserting an HCP lamella into an FCC crystal. Regularly spaced faults spaced two layers apart would convert an FCC crystal entirely to HCP, or an HCP to FCC. A fault in an FCC crystal is also equivalent to creating an FCC twin of minimum thickness; in fact, the entire crystal would be converted to its twin if faults were introduced regularly. (In HCP crystals, however, twinning does not occur on the basal plane and a fault on this plane is not identical with a thin twin). Faults are one of the possible causes for annealing twins,' for the strain markings that are brought out by etching deformed metal,'," for the altered X ray reflecting power of metal at slip bands that is revealed in X ray reflection micrographs,' for the extinction of Kikuchi lines in electron diffraction patterns, and for the hardening of latent slip planes.' Since other explanations of these effects are also available," there has been no direct proof of faults from deformation; yet it has appeared likely that they would occur. Faults resulting from phase transformations in metals, however, have been clearly revealed by diffraction in cobalt" and lithium. It is to be expected that the faulting tendency is greatest

Jan 1, 1951

By A. A. Burr, D. G. Ebeling

The effects of casting texture, grain orientation and grain size upon the performance of Alnico permanent magnets is described. Single-crystal specimens were produced by special sintering and grain coarsening techniques to study the effect of crystal orientation. In addition to texture and orientation effects, an analysis of the results indicates that the permanent magnet performance is impaired by a refinement of the grain size. AN excellent historical review of the development of Alnico permanent magnets has been prepared by Bozorth.1 The desirable permanent magnet characteristics of Fe-Ni-A1 alloys were discovered in 1932 by Mishima.2,3 The work of Ruder' showed that the alloys were age-hardenable, and Betteridge5 defined the best composition and heat treatment for the magnetically isotropic alloy known as "Alnico 3." Horsburgh and Tetley0 increased the energy product by the addition of cobalt and copper, "Alnico 2," and Oliver and Sheddon7 demonstrated that cooling in a magnetic field improved the residual induction of this alloy. Jonas8,9 then disclosed the great practical benefits of heat treating an alloy of higher cobalt content in a magnetic field and the resulting alloy, "Alnico 5," has become the standard of the industry. This paper describes the fundamental aspects of a procedure which can be used to further improve the properties of these anisotropic permanent magnet alloys. A study of the casting techniques used in the production of anisotropic Alnico permanent magnets indicated that the magnetic quality was affected by the as-cast macrostructure. Improved performance was observed in magnets containing a high percentage of columnar grains whose long axes were parallel to the magnetic axis of the casting. McCaig10 studied the effect of such columnar grain structures upon the magnetostriction characteristics of similar alloys, however no data was presented showing the effects on other magnetic properties. The following paragraphs describe two experiments which were conducted to determine the effect of various grain orientations upon the energy product. Special composite molds were prepared of highly conductive and highly refractive components to remove the heat of solidification from the casting in a controlled manner. Representative macrostructures produced by these techniques are shown in Fig. 1, along with the relative volumes of favorably oriented columnar grains. The alloy, Alnico 5, has the highest permanent magnet performance of any commercial magnet material. It has the nominal weight composition of 8 pct Al, 14 pct Ni, 24 pct Co, 3 pct Cu, and 51 pct Fe. A heat of this material was cast into molds producing the type A and B grain structures shown in Fig. 1 and pairs of the resulting magnets were placed in heat-treating boats so as to eliminate any biasing effects of boat position. After a standard heat treatment the type A magnets, with 16 pct of the volume composed of favorably aligned grains, had a maximum energy value of 3,940,000 gauss-oersteds, while the type B magnets with 73 pct aligned grains averaged 5,090,000. This large im-

Jan 1, 1954

By F. L. Wolf

The catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though it's importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation. Technical literature was studied, metallurgical experts were consulted, and the problem was discussed with engineers who were in close contact

Jan 1, 1930

Jan 1, 1891

By P. Davey Wheeler

San Francisco meeting, September, 1915) IN an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in. thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. 1.) Fig. 2 is a photograph of the end of the punching, showing the .hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of, radiographing metals. In order to gain some preliminary data, several pieces of ½ -in(12.5mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter 1 1/4 in. = 6.3 mm 2 1/8 in. = 3.1 mm. 3 1/16 in. = 1.6 mm. 4 1/32 in. = 0.8 mm. 5 1/64 in. = 0.4 mm.

Jan 8, 1915

By J. A. Herrick

For a long time, especially in Europe, heavy pieces of forging, such as cannon, armor plates, marine shafting, etc., have been steadily augmented in size, more particularly since steel has been substituted for wrought iron. To keep pace with these forgings several very large hammers have been, from time to time, erected. The most powerful and thoroughly appointed of all now in operation is that designed and built by Messrs. Schneider & Co. at their' works at Creusot, and it is the design of this communication to give to the members of the Institute a concise description of this remarkable piece of mechanism, which I have taken from an article published in the Annales Industrielles. This hammer is rated nominally at 80-tons power, but its capacity is, in reality, far greater, as will be seen by the comparative figures given later. The complete plant, comprising the hammer, the cranes, the furnaces, and the building which shelters the whole, is distin-

Jan 1, 1880

By J. A. Herrick

FOR a long time, especially in Europe, heavy pieces of forgings, such as cannon, armor plates, marine shafting, etc., have been steadily augmented in size, more particularly since steel has been substituted for wrought iron. To keep pace with these forgings several, very large hammers have been, from time to time, erected. The most powerful and thoroughly appointed of all now in operation is that designed and built by Messrs. Schneider & Co. at their works at Creusot, and it is the design of this communication to give to the members of the Institute a concise description of this remarkable piece of mechanism, which I have taken from an article published in the Annales Industrielles. This hammer is rated nominally at 80-tons power, but its capacity is, in reality, far greater, as will be seen by the comparative figures given later. The complete plant, comprising the hammer, the cranes, the furnaces, and the building which shelters the whole, is distin-

Jan 1, 1880

By E. V. Potter, E. T. Hayes, H. C. Lukens

Large volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that bite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.l.2 The close relationship between iron and manganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. Apparatus The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of IOO C.C. for a 60-cm. length. For larger changes in gas volumes, auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By John D. Siddle

Efficient energy utilization in the electrolytic zinc process, relative to other zinc processes, is one of the reasons for its wide adoption in recent years. Designers and operators of electrolytic zinc plants have pioneered process improvements, new equipment, and operating techniques to conserve energy. As energy costs advance still higher in the future, and competitive pressure against the less efficient producers increases, these or alternative energy-saving methods will be looked upon as a necessity for economic survival. Estimated energy savings which may be achieved by various equipment and techniques are included.

Jan 1, 1977

By Otis W. Freeman

Production of oil in Indiana during 1944 is estimated at approximately 4,950,000 bbl., a decline of 6 per cent from the preceding year. Shortage of labor and material, together with governmental regulations resulting from the war, largely account for the drop in output and limited new developments. Three new pools were discovered in the state during 1944. Two of these, New Harmony, South, and Hovey, West, are in Posey County. Six wells in the New Harmony, South, field produced 66,422 bbl. of oil last year. A third field, Cato, in Pike County, did not market the oil from its discovery well during 1944. Several wells discovered oil in the Henderson field of Jay County along the Ohio state line. An important south extension of the St. Thomas field in Knox County was discovered during the year. Active drilling took place in the Inman, East, and Upton fields, Posey County, both discovered in 1943. Twenty-two wells in Inman, East, produced 151,1gr bbl. in 1944 and 12 in Upton produced 107,052 bbl. Owensville, and especially Owensville, North, in Gibson County, made large gains in production as a result of active drilling. The Dodds Bridge field in Sullivan County continued good production from deep sands reached in 1942. The Griffin continued to be the largest producer among the oil pools of Indiana, accounting for 2,004,180 bbl., over 40 per cent of the state's output. The next largest producing fields are Mt. Vernon and New Harmony, both in Posey County. The largest gas well brought in during 1944 was in the Rockport field, Spencer County, and had an initial output of 2,680,000 cu. ft. per day. The most productive gas fields in Indiana are Rockport, Spencer County, Greensburg, Decatur County, and Unionville, Monroe County. Total production in the state is . hard to estimate, as considerable gas is consumcd in farm homes and for other local uses, and never is reported, but was near 1500 million cubic feet. Some oil from the Trenton field is also used locally and is unreported from pipe-line runs. A total of 606,145 ft. of new hole was drilled in Indiana in 1944. Most of the completions were in Posey and Gibson counties, although wells were drilled in 36 different counties. During the year 331 wells were completed. Of these, 145 found oil in commercial quantities and 28 were gas wells. The initial production of the 145 oil wells was 11,908 bbl. per day. Settled production would be less, of course. The largest wells reported during the year were two on the J. W. Mann farm, in the Mt. Vernon field, with a flush flow of 500 to 800 bbl. each.. Six pools, all small "one well" affairs, were abandoned in 1944; i.e., Fleenor and Patoka in Gibson County, Grafton and Rapture in Posey County, Vaughn in Vandei-bwgh County and Millersburgh, Warrick County.

Jan 1, 1945

By C. R. Boyd

WITHOUT attempting to do more than give a preliminary or skeleton report upon the geology and minerals of Southwestern Virginia at this time, I am led to hope that the great commercial importance of the sixty miles of cross-section here crudely treated of

Jan 1, 1877

By C. Scala, M. Gondouin

Published laboratory data have established that very significant streaming potentials can exist across mud cakes subjected to pressure differentials such as exist between a mud column and formation fluids. Since shale is similar in kind and in properties to a well-formed mud cake, it appeared possible that streaming potentials might also arise across shales. A practical consequence would be that the streaming potential contribution to the SP would be smaller than might otherwise be assumed since the SP is measured with respect to the "shale bare line". The resultant contribution would be the difference between the streaming potential across the shale and that across the mud cake. In order to investigate this possibility, a laboratory apparatus was devised for measuring streaming potentials under pressure conditions normally encountered in wells. Reported data on streaming potentids across mud cakes were verified. More important, appreciable streaming potentials were found across shale samples. As in the case of mud cakes, the shale potentials varied with the concentration and nature of the impregnating electrolyte. Dependence on pressure was In a different rela-tion than that for mud cakes, possibly because of the lower compressibility of shales. The differences in streaming potentials between the shales md mud cakes were generally small, although they might vary considerably in practice depending on the relative electro-kinetic properties of the particular shale-mud cuke combination. A "poorly eflective" shale with a "very eflec-tive mud cake" would produce the largest negative addition to the electrochemical component of the SP. Results of field experiments with pressurized wells were considered in the light of the laboratory results. INTRODUCTION Field experiments wherein the pressure of the mud column in a borehole was varied have often indicated the presence of a streaming potential, but its magnitude was not easily predictable and its sign sometimes changed from one formation to another in the same well.' In the interpretation of SP logs from standard surveys, nevertheless, the correct value of R,, is very frequently obtained, within the limits of field accuracy, using only the simple electrochemical expression of the SP provided that proper corrections are made for bed thickness, ion activity, etc.' Accordingly, it was apparent that the streaming potential component of the SP in a borehole was considerably more complex than commonly assumed and clarification was indeed necessary The close similarity in nature and constitution of a shale to a well-compacted mud cake suggested that a streaming potential might also exist across shales as pointed out by M. P. Tixier in 1953 and as recently emphasized by Wyllie." e practical consequence would be that the streaming potential across the mud cake would be canceled, at least in part, on electrical logs since the SP is recorded with respect to the shale potential as a base line. This appeared to be a plausible explanation for many of the effects observed but no supporting data were available. In 1955 preliminary experiments at low pressures were conducted in our laboratories which supported the hypothesis of the shale streaming potential and formed the basis for later studies at borehole pressures.* EARLY LOW PRESSURE EXPERIMENTS The early experiments were conducted primarily to determine the possibility of a streaming potential across shales. The shale used was a compact type designated as No. 7 from Reagan County, Tex. (Permian). Cut samples were saturated for over one month in .2 to 2.0-N NaCl solutions. In order to eliminate all electrode polarization effects, a dynamic method was used. A transient pressure of about 1 atm was applied across

By Howard V. Sears

ArcHodrilling (Arcuate Hole Drilling) of short radius overhead curved holes from within the working level with a new, small-diameter in-the-hole drill produces tangible, assayable chip samples from the entire height of the projected mine level where the hole arcs down immediately in front of the working face. Drilling through the projected level with diamond coring tools produces samples showing the competence of roof and floor strata as well as the geological and economic characteristics of the ore. Hand-portable solid state electronic surveying instrument has been developed to survey the ArcHole and a convenient nomograph plotting record sheet converts survey digital readouts to hole inclination in degrees, to radius of curvature in feet, and to attitude of the plane of curvature from vertical in degrees, all without calculation. The ArcHodrilling system offers a tool with which the exploration geologist can more nearly assess the true potential of old mining properties being reexamined and to reduce the number of surface diamond drill holes needed to secure development data about new ore bodies. It gives the mine geologist an opportunity to secure those data at a fraction of the cost of drilling from the surface. The mining supervisor has a convenient, cheap tool to look ahead to know what he will be mining tomorrow. The mill supervisor has an opportunity to reduce his mineral loss in tailings by being able to anticipate the grade of his mill feed.

Jan 1, 1973

By Arthur A. Brant

Let us start back as far as possible, to the beginnings of this universe, some 5 billion or more years ago. This is a time interval that can be crudely underestimated by the moon-earth tidal friction effects that have increased the length of the day by about 1/1000 second per century-from a 5 to 7 hour day to its present 24-and have moved the moon away at 5 inches per year to its present 240,000 miles. The oldest stony meteorites from interplanetary space give an age dating of some 4.6 billion years, approximating the time of formation of our earth. Further, certain stars pulsate, the period of pulsation being related to their absolute brightness. Measuring apparent brightness and comparing, gives the distance away. Thus Hubble and Shapley of Harvard, from 1925 on, were able to show that the universe reached as far as our telescopes could scan. The Doppler shift of the hydrogen red lines could only mean that the nebulae, or galaxies, were moving away at velocities increasing with their distances, by 180 km/ sec velocity increase for every million light year's distance. In short, the universe is expanding like an exploded bomb.

Jan 4, 1964

By Kurt Kennedy

A method is described by which three elements can be condensed simirltaneously on a common substrate in such a way that the composition varies with position on the substrate. Almost all possible combinations of three solid elements can be formed in a single evaporation. The three elements are heated by magnetically deflected electron beams. The alloys and cornpounds formed by this method generally correspond to those trade by other methods; however, many exceptions exist. Simple symmetric crystallographic phases tend to form in preference to more complex phases. The Nb-Sn. Cr-Fe-Nt, and other systems of alloys made by this method will be discussed. Phases that form very slowly, such as the o phase in Cr-Fe alloys, may be formed rapidly by this method when certain substrate temperatures are used. STUDYING all the mixtures and compounds of two or more elements by the preparation of individual samples forces the investigator to make sampling sufficiently close together so that the properties of the intermediate compositions can be inferred. A completely unknown system will require a dis c our aging ly large number of preparations in order to fully know all its properties. For the purpose of expediting this type of investigation, methods have been devised to prepare samples that have a continuous variation in composition over some predefined area. The code-position of two elements onto suitable substrates has been used to produce alloys or compounds that have variable compositions depending on their positions on the substrates Composition gradients have been formed by depositing a wedge-shaped layer of one element and then depositing a second wedge-shaped layer on top of it such that the total film thickness is kept constant. Concentration equilibrium perpendicular to the surface is then established by annealing.4 This paper describes a method for the simultaneous condensation of three volatile components on a substrate such that there is a regular variation of composition with position on the substrate. The arrangement of the evaporation sources and the substrate is shown schematically in Fig. 1. Materials to be evaporated are placed in three water-cooled crucibles located at the corners of a 10-in. equilateral triangle. Electron beams from cathodes located below the crucibles are bent 180 deg by magnetic fields and focused on the material to be evaporated. The cathodes are connected in parallel to a constant-current 12-kv power supply. The distribution of emission current from each cathode is controlled by filament temperature. When materials that sublime are to be evaporated, the electron beam is deflected by an auxiliary ac magnetic field so that the beam moves over the surface of the evaporating material rather than digging a hole in one spot. The substrate is a 10-in. triangle of 2-mil stainless steel or molybdenum which is stretched against a slightly curved heat sink by a frame as shown in Fig. 2. This frame and heat sink are located so that each corner is directly above an evaporation source. The heat sink has three radiant heaters at each corner that can be separately controlled permitting the

Jan 1, 1967

By James Douglas

The development of the copper-resources of this country has kept close pace with the unfolding of its geographical area to commerce. In colonial days, when our English ancestors occupied only the Atlantic seaboard, insignificant quantities of copper were mined in Connecticut, New Jersey, and Pennsylvania, and the ore was shipped for treatment to England. The first steam pumping-equipment

Jan 1, 1891