Search Documents

By J. L. Taylor, P. Duwez

The phase boundaries in the ternary system Ti-Cr-Al have been established at 1800° and 1400°F for alloys containing more than 60 pct Ti. The martensite transformation temperature has been measured for the titanium-rich alloys. THE studies of binary alloys of titanium with the transition elements which have been published so far1-0 ndicate clearly that the solubility of these elements is always much greater in the high temperature body-centered cubic form of titanium (ß phase) than in the low temperature hexagonal form. In this category of alloying elements are iron, nickel, chromium, manganese, vanadium, molybdenum, tungsten, columbium, and tantalum. Although studies of the nontransition elements have been rather limited, early work on titanium binary alloys'" has shown that most of them were not very soluble in the a form, with the exception of aluminum, for which the solubility in a is about 25 pct.13, 12 In addition to this large solubility in a, aluminum is also soluble in ß titanium to the extent of about 35 pct and the transformation temperature from ß to a is raised with aluminum content. This effect is also typical of aluminum, in contrast with that found for the transition elements which lower the ß to a transformation temperature. Therefore, it may be anticipated that tprnarv titanium alloys with aluminum and any one of the transition elements will constitute a class of ternary alloys having characteristic features absent in alloys involving two transition elements. Chromium was chosen as a typical transition element for the present study because ternary alloys of Ti-Al-Cr commercially produced have been found to possess very interesting physical properties (MST-3 pct A1-5 pct Cr of Mallory-Sharon).'" Binary Systems The binary systems Ti-A1 and Ti-Cr have been established recently by several investigators. The data used in this investigation were taken from the complete diagram of Bumps, Kessler, and Hansen." This diagram agrees quite well with earlier investigations." For the Ti-Cr system, the phase boundaries at 1800" and 1400°F were taken from refs. 6 and 7. The binary system Cr-A1 has been studied recently by Bradley." This system is rather complex and contains not less than seven intermediate phases. The present study was limited to the titanium corner of the ternary system (less than a total of 40 pct Cr plus Al) and none of the phases present in the Cr-A1 binary alloys were found in the ternary alloys investigated. Experimental Technique Microscopic observation and X-ray diffraction measurements were used to identify phases and de-

Jan 1, 1954

By Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing: with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two mono-graphs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon.

Jan 1, 1930

THE Copperton mill in reality was a sort of proving ground. It was. designed to serve three purposes: (1) to verify the accuracy of the mine sampling by actually treating substantial tonnages of ore, (2) to demonstrate on a reasonably large scale the percentage of the copper in the ore that could be recovered, and (3) to permit the testing of various kinds of machines and devices for crushing and concentrating the ore, so as to guide the engineers in designing the proposed 6000-ton milling plant at Garfield. As a matter of fact, it contained a lot of second-hand equipment sent by MacNeill and Penrose from the works of the United States Reduction &Refining Co. in Colorado; and it was by no means a model installation. Probably it would have been even less efficient, except for the skillful work of George O. Bradley and-Frank-G, Janney, both of whom had worked with Jackling at Mercur. Bradley was a mechanical engineer employed to design the plant. Later he directed the design of the concentrator at Garfield and remained as consulting mechanical engineer to the company until 1915. Janney, who afterwards became manager of mills, a position that he retained until his death in 1916, was a skilled mechanic at the Golden Gate mill at Mercur when Jackling built the plant in 1897. His flair was making machinery do what it was intended to do. He was not an ore-dressing engineer in a technical sense; but Jackling him- self was a specialist in this respect as well as in designing and construction and Janney's mechanical aptitude made him a particularly valuable man in the Utah organization. John McDonald, another of Jackling's Mercur associates, was the first mine superintendent. With practically all of the available funds earmarked for construction of the Copperton

Jan 1, 1933

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

Large scale mining of Mesabi taconites may have moved nearer to realization with the arrival of the latest model Linde Jet-Piercing machine at Reserve Mining Co.'s Babbitt, Minn. property. When the machine is placed in operation it is expected to pierce blast holes in the hard taconite beds up to 10 times faster than is possible with existing drilling equipment. The new primary blast hole drilling machine has been designated the JPM-3, and is the successor to the JPM-1, in operation at Erie Mining Co.'s taconite mines at Aurora, Minn. The size of primary blast holes which can now be pierced has increased from a nominal 61 in. diameter to 71 in. diameter and maximum hole depth has increased from 35 ft to 47 ft. Development has progressed to where 71/2 in. holes can be pierced with the same speed as 61/2 in. holes. Piercing progress is controlled by electronic blowpipe descent controls. Other features of the JPM-3 include: automatic burner ignition from the operating cab; heated and air conditioned operating cab designed for all-year operation; mechanical improvements for sub-zero operation common to the Mesabi, and redesign of wearing parts for longer service with minimum maintenance. The 40-ton machine is self-propelled. Power, oxygen, and cooling water lines trail from the machine. Jet piercing is based on combustion products of oxygen and a liquid fuel such as kerosene. The flame, jetting from a burner at speeds of about 6000 ft per sec, disintegrates layers of spallable rock. The burner is cooled by water which is then directed through orifices around the periphery of the burner. The water changes to steam and carries the spallings out of the hole. The equipment used in Jet-Piercing is essentially a tractor-mounted blowpipe containing a combustion chamber and nozzle, which is in effect a miniature rocket motor, from which the supersonic combustion gases emerge to do their work.

Jan 1, 1952

By T. Egleston

FOR a great part of the progress of the world we are indebted to the works of engineers. It is to them that we owe our means of rapid transportation, our canals, our railroads, our bridges, many of our automatic machines, and most of those appliances which, by facili tating or decreasing the amount of human labor to be expended and by utilizing the great forces of nature, have made the present progress of the world possible. Their education is a matter of momentous interest to the whole civilized world. I have, therefore, thought that some discussion of the theory upon which their education should be based would be of interest to this body, and have ventured a few reflections and suggestions upon the subject. The word education, in its original signification, meant the draw ing out of a man what there was in him. In our common schools the practical work of education consists in putting into the brain a larger number of facts than can be retained, which are consequently more or less understood and digested. It ordinarily consists simply of teaching a round of abstractions or facts which when not assim ilated are not only useless to the individual, but generate careless habits of thought and make more or less untruthful, unfaithful or unsuccessful men. In most of our schools a procrustean system is adopted; all are made to advance upon one general plan, the quick being kept back and the slow dragged on at a rate too great for their power of comprehension. Until within a very few years it has been a theory in common school education that the brain alone should be developed, and that little or no attention need be paid to the train-

Jan 1, 1888

By Chung Yu Wang, Guy C. Riddle

There are found in nature upward of II2 minerals containing antimony, but only a few of them, listed in Table I, can be considered as antimony ore-forming minerals. Stibnite (Sb2S3), antimony sulphide or glance, is the principal ore of antimony. The oxide ores—cervantite, kermesite, valentinite, sernarmontite—occur sparingly in nature. Dry methods are generally adopted for the extraction of the metal. Electrometal-lurgical methods have had much attention in America and Germany and have not yet found, on economic grounds, practical or extended application, except in a few places. During recent years, treatment of the poor grades of the ore, especially sulphide, by ore-dressing methods, has commanded some attention and been adopted at a few plants. The impure sulphide of antimony, resulting from the liquation process, is called lLneedle," "liquated" or "crude" anti- mony, and the refined metal itself is called antimony "regulus." The different processes for the treatment of antimony ores are shown in the diagram of Fig. I. Liquation of Crude Antimony The first step in the smelting of antimony is a simple one, the process of LLliquation," which produces crude or needle antimony. Ores containing $ 50 per cent Sb are used in the liquation process for the production of crude. The temperature required for liquation is between 550' and 600°C. Ores to be liquated are broken to about walnut size. If the pieces are larger than this, the low heat used will not penetrate' effectively, and if they are smaller the ore tends to pack too closely for adequate penetration. A packed charge also prevents the free escape of the fused sulphide. Intermittent Liquation in Crucibles The unique type of furnace that is in use in China for smelting is not highly efficient but is simple in construction and operation. The furnace is generally built

Jan 1, 1944

By Y. G. Shiau, J. E. Burke

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By J. E. Burke, Y. G. Shiau

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By A. H. Daane, R. L. Myklebust

The yttrium-manganese system has been investigated by thermal, metallographic, and X-ray diffraction methods. There are three intermetallic compounds present: YMn2 which melts congruently, YMn4, which undergoes syntectic decomposition, and YMn,, which undergoes peritectic decomposition. The compound YMn4 is ferromagnetic at room temperature with a Curie temperature of 214°C. There are eutectics at 25.2, 60.9, and 82.0 wt pct Mn which melt at 878°, 1100°, and 1075°C, respectively. Crys-tallographic data are given for YMn4, and YMn12 . The terminal solid solubilities are low. In a general program of study of yttrium metal in this laboratory some alloy systems of this metal with elements of the first transition period have been examined. This work was originally instigated by experiences in cladding yttrium with jackets of some protective metals such as Inconel for high-temperature service in air.' In some cases a low-melting phase was observed to form between the Inconel and the yttrium resulting in failure of the samples. In characterizing this reaction, a survey was made of the systems of yttrium with chromium, manganese, iron and nickel,, and it was found that a eutectic was formed between these metals and yttrium on the yttrium-rich side of the system. This present study of the Y-Mn system was carried out to examine in more detail the alloying nature of yttrium, and to correlate trends that have been observed in previous related studies. It was observed by Voge13 that in the systems of lanthanum, cerium, and praseodymium with each of the metals in the first transition series, the tendency to form compounds diminished in the order nickel, cobalt, and iron while no compounds were formed with manganese, chromium, or titanium. Beaudry and Daane4 observed a similar behavior in the systems of yttrium with some members of the first transition series except that the tendency for compound formation was greater. Both the Y-Ti5 and Y-Cra systems consist of simple eutectics, while in the Y-Fe,7 Y-CO, and Y-Ni4 systems, there are four, eight, and nine compounds, respectively. In addition to the above trends, the similar atomic radii and electronegativities of yttrium and thorium invite a comparison between their alloying behaviors with a common element such as manganese. In crys- tallographic studies, Florio et al.' have identified three intermediate phases in this system which are ThMn2, Th6Mn23, and ThMn,,. Gschneidner and Waber10 have examined published information on alloy systems of the rare-earth metals and have correlated this information with current alloying theory. From their study, they predicted that the Y-Mn system would contain one intermetallic compound. On the basis of this prediction, the trend in the alloying behavior of yttrium with the elements of the first transition series and the alloying behavior of thorium with manganese, one might expect from one to three intermetallic compounds to form in the Y-Mn system. A consideration of Hume-Rothery's rules of alloying based on size-factor, electronegativity, and valency suggested a small terminal solubility and possible compound formation. The present study was undertaken to confirm these predictions of low terminal solid solubility and compound formation and to establish the general alloying behavior of yttrium with manganese. EXPERIMENTAL Materials. The manganese used in this investigation was obtained from the Foote Mineral Co. as electrolytic plates of 99.9 pct stated purity; the yttrium metal was prepared in this laboratory. Table I gives the analyses of these materials. For the solubility studies at the yttrium-rich end of the alloy system, distilled yttrium, whose major impurity was 200 ppm Ti, was used. Preparation of Alloys. The alloys were formed by comelting the two metals in an are-melting furnace under an atmosphere of argon. The buttons thus formed were inverted and remelted three to five times to promote homogeneity. Due to the high vapor pressure of manganese, it was assumed that the weight lost during are-melting was all manganese. This assumption was based on the very good agreement observed between calculated compositions and chemical analyses of several alloys. The compositions of the dilute alloys used for solid solu-

Jan 1, 1962

By Howard Reiss, C. S. Fuller

A theoretical and experimental study has been made of those interactions between holes and electrons which influence the solubilities of donors and acceptors in semiconductors. The major portion of the work concerns the solubility of lithium in silicon doped to varying degrees with boron. This solubility increases with increasing boron content in a manner predicted by theory and exhibits the expected temperature dependence. A qualitative experiment in germanium is described which demonstrates, in accordance with theory, that doping with a donor decreases the solubility of another donor. SEVERAL authors have discussed the possibility that holes and electrons behave like chemical entities and influence the solubilities of ionized impurities, Wagner was the first to invoke this concept in connection with his studies on nonstoichio-metric oxides. He used it again in explaining the solubility of hydrogen in molten binary alloys. In a theoretical paper,' Reiss drew attention to the fact that solutions of impurities in semiconductors

Jan 1, 1957

By I. R. Kramer

The stress associated with the surface layer was deter-minedfor iron and molybdcnum. These measurements show that the surface layer plays a very important role in the plastic deformation of bcc metals. From the relationship between strain arui the surface layer stress and the back stress imposed by the internal obstacles, it is Proposed that the term of of the Hall-Petch equation is related only THE large number of studies on plastic flow of bcc metals have failed to delineate clearly the nature of the obstacles influencing dislocation movement. Since there have been numerous articles which have reviewed the mechanisms proposed to explain various aspects of plastic flow of bcc metals (for example, conrad1 and Keh and weissmann2), no attempt will be made here to discuss their conclusions. However, it should be to the surface stress while the term Kfd is the stress required to move dislocations through internal obstacles. Further, it was possible to derive the well-known empirical equation C = , and it is shown that the terprz a is comprised of two terms: a term Cs associated with the surface layer stress and Ci related to internal dislocation obstacles. pointed out that in all of these publications it has been tacitly assumed that plastic flow occurred uniformly throughout the cross section of the specimen (except, of course, for the Luders band region), It has generally been further assumed that the nature and distribution of the obstacles opposing the motion of dislocations are of the same type throughout. The role of the surface layer in bcc metals has not, as yet, been considered even though its role in fcc metals has been shown clearly to be of primary importance.3-5 Investigations on fcc metals have shown that at the onset of plastic deformation a surface layer acts to

Jan 1, 1968

By Charles Pack

Extensive progress has been made in the metallurgy of alloys for die castings. Enthusiastic proponents of some alloys are inclined to make extravagant claims for their materials, which may be justified by physical tests on test bars made from the respective alloys but are seldom justified by the results obtained with commercial die castings made from those alloys. Chemical analysis of the test bars and castings fails to determine the cause of these variations, since they are due to other physical factors entering into the commercial production of die castings. In this paper, an attempt will be made to outline some of the factors in commercial die-casting practice to which these variable results may be attributed, in the hope that the manufacturer of die castings, recognizing the importance of these factors, will devote more attention to them in the design and construction of dies and equipment. In 1914,l the author defined die castings as "metal castings made by forcing molten metal, under pressure, into metallic molds or dies." This definition was given in order to differentiate die castings from other molded metal products such as "permanent-mold" castings, L'slush" castings and similar products that are sometimes erroneously termed die castings. The term "die casting" could be interpreted to include all castings made in metal molds or dies; but since this term, like most of our technical nomenclature, has been developed by commercial practice we must look to this practice for its proper definition. The Germans, with their usual devotion to desecriptive names, have adopted the name of sprilzguss (squirt cast) for die castings. Undoubtedly this name is more descriptive of the die-casting process, where the metal is literally squirted into the die and serves to differentiate this process from other metal mold processes, where the metal is poured into the die. In the earlier paper mentioned, the author also emphasized the fact that the definition given for die castings indicated clearly that the satisfactory operation of the process must comprise three factors, all of which must be considered of vital importance to the successful operation of the die-casting process:

Jan 1, 1931

By V. C. Wansbrough

A LUCID, thorough and powerful review of the impact of your tax laws on mining operations has already been presented by Granville S. Borden*. He has brought into focus and relief the pressure-points at which the shoe pinches most, has suggested some remedial measures, and enunciated much sound doctrine about the interrelationship and interplay of taxation policy and mining activity. Under the heading "What Every Lawmaker Should Know", he laid down the fundamental proposition that "the magnitude of our mineral resources varies inversely with the magnitude of the taxes levied upon them." With this, as with his other major premises, all mining men must be in hearty concurrence. There can be no doubt that a flourishing and expansive future for the mining industry in this country, in Canada, or anywhere else will depend on the thoroughness with .which these fundamental propositions are grasped by legislators, by national policy-makers and by public opinion at large.

Jan 1, 1950

By C. F. Cockrell, H. E. Shafer, J. W. Leonard

A significant technological development is discussed for the processing of certain power plant flyashes that are a problem because they contain a high water-soluble mineral content and yield inferior flyash-based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash-based structures. Favorable changes are evi-dent in sodium silicate consumption, where about half the amount used for making brick from normal flyash is required, processing costs, and strength and appearance of the resulting freshly formed green and fired structural products. In some high cost in-stances (above the $30 or less per thousand brick estimated for normal flyash), hydrochloric acid additions can replace or reduce other costly additives normally required for problem flyashes. This results in savings of as much as $9 per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble sulfur as a result of the eventual application of certain experimental air pollution control processes. Much of the research datal-6 accrued through work by the Coal Research Bureau of West Virginia University for the Department of Interior's Office of Coal Research on converting waste power coal ash to valuable brick and other structural products, can be categorized as follows: (1) general ash-to-brick tech- nology; (2) specific ash-to-brick optimization; (3) pilot plant progress; (4) production cost estimates. A summary of the progress on bench-scale experiments indicates that coal ash can yield two types of brick. An acceptable brick is obtained by mixing 73.6% fly-ash, 23.5% bottom ash and 2.9% sodium silicate solution (dry basis). Depending on the flyash and bottom ash used, optimum brick can be manufactured by mixing 72-77% flyash, 20-25% bottom ash and 2.3-3.0% sodium silicate (dry basis) with Na2O : SiO2 ratio varied according to the composition of the flyash used. These blends are thoroughly mixed and mechanically formed into green brick shapes at pressures ranging from 1000 to the more usual 3000 lb per sq in. The green shapes then are dried and fired at temperatures ranging from 1975-2150°F using clay brick cycles that are shorter than standard. Other findings reported to date indicate that when making optimum brick, it is necessary to carefully control the top size of the moisture-releasing bottom ash so that it falls between 8 and 30 mesh, depending on the flyash used. Moreover, the chemical composition of bottom ash and flyash have been found to be of little significance with the exception of a few problem flyashes which are the subject of this paper. Finally, the pilot plant, which was previously reported under construction, is now in operation. This will indicate, among other things, the cost of brick production, which was earlier estimated for non-problem flyashes at $30 or less per thousand brick. The foregoing bench-scale technology is applicable to all the initially tested ashes as well as to the majority of ashes examined during the course of research. However, a few of the ashes yield green and fired products that may be structurally inferior or unacceptable, necessitating excessive and diverse reagent addition, and/or may be coated with unsightly surface deposits. These problem ashes generally originate in certain areas of Illinois, western Ken-

Jan 1, 1969

By Stephen Taber

Introduction.............................. 62 Asbestiform Minerals.......................... 63 Chemical and Mineralogical Relations............... 63 Physical Properties........................ 64 Types of Asbestos............................ 65 Origin of the Fibrous Structure...................... 66 Views of Previous Investigators.................... 66 Discussion of the Evidence.................... 67 Conclusions........................... 69 Origin of Cross-fiber Veins....................... 71 Chrysotile Veins......................... 72 Structural Features of Cross-fiber Veins............... 78 Veins of Crocidolite and Other Fibrous Amphiboles........... 83 Origin of Slip-fiber........................... 84 Origin of Mass-fiber........................... 86 Discussion............................... 87 IntRoduCtion The term asbestos, as commonly used, includes half a dozen minerals all having a well-developed fibrous structure, but differing in chemical composition and in some of their physical properties. In its strict application the name is limited to the fibrous varieties of the monoclinic amphiboles. Commercially, however, the most important of the asbestiform minerals is chrysotile, a fibrous variety of serpentine. About 95 per cent. of the asbestos used in manufacturing is chrysotile, and it commands a much higher price than any of the other fibrous minerals now on the market. Although the production of asbestos has increased rapidly in recent years, comparatively little has been published concerning its origin. The present paper is preliminary in its nature, and therefore does not pretend to exhaust the subject. The ideas herein developed are the result of field investigation, laboratory experiments in the growth of fibrous

Jan 1, 1918

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By C. E. Jr. Reistle

ALL crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms.

Jan 1, 1927

By Waldemar Lindgren

No one would maintain that all ore deposits or all deposits of useful minerals have been formed by the same processes. Generally they have originated by special processes of concentration but these may be of many different kinds. Some deposits have their origin in chemical or biochemical processes of concentration in rivers, lakes or seas, others developed on land by means of chemical reactions of surface waters on various forms of rocks. Certain insoluble substances remained behind; others were dissolved and precipitated in favorable places. This action proceeded in the realm of the oxidizing surface waters or in the deeper zones to which the waters from the surface could find their way. Examples of the latter kind may be found in the extensive copper and vanadium deposits of some sedimentary beds or in the lead and zinc deposits of certain broad limestone strata. In these instances the evidence for any other mode of origin would seem to be very weak indeed.' Nor does it seem possible to deny that circulating waters may form deposits of the more common metals along fissures after having dissolved many constituents from paths traversed. Another very large class has been formed by magnetic processes of concentration. The last 40 years have been a period of intense activity in the investigation and description of a vast number of deposits; all modern methods have been employed and the result is an accumulation of data, difficult or impossible to master. It has been a period similar to that in petrography. The generalizations, the able deductions, have lagged behind. Evidently several geologists have become weary of this "infinite detail" and a mistrust of the microscope seems to have arisen. Although this feeling of being swamped in microscopic detail is a painful experience, nevertheless only through the detail in combination with the large features, and only by utilizing all the related sciences shall we

Jan 1, 1927