Search Documents

By C. D. Tedmon, D. P. Ferriss

THE yield stress, o of low-carbon steel has been shown to vary with the average grain diameter, d, according to the relation1-3 where o is taken to be the lower yield-point stress Of is the friction stress on an unlocked dislocation, and ky is a constant. The interpretation2,4 of ky in terms of dislocation theory relates this constant to the stress to unlock a source across a grain boundary. cottrel14 predicted that ky would increase with decreasing temperature. This was observed to be the case by Adams and coworkers5 in their investigation of niobium (columbium). However, petch6 and Backofen: both working with low-carbon steel, found ky insensitive to temperature. In his work with high-purity niobium, Johnson' found ky equal to zero. Evansg showed that k, was essentially zero for niobium containing nitrogen in an appreciable concentration range. The present experiments were designed to check this apparent anomaly in the value of ky in another Group V metal. Yield points were determined as a function of grain size at several temperatures for tantalum and a tantalum-tungsten alloy. The material used was double are-melted tantalum and a double are-melted alloy of 90 pct Ta and 10 pct tungsten (by weight), both obtained as unannealed, swaged rod. The impurity content of the materials is given in Table I. The tantalum was annealed at 1325"C. in a vacuum resistance furnace using a tantalum boat. The alloy was similarly annealed at 1660°C. Annealing times varied from 15 min to 2 hr, depending on the desired grain size. Nominal pressure in the furnace was 3 X 10~4 mm of Kg. Metallographic examination showed that the annealing treatment produced grain sizes ranging frorn 0.021 to 0.200 mm in the tantalum, and 0.060 to 0.160 mm in the alloy. Tensile bars were made by centerless grinding the annealed specimen;, and then electropolishing to remove all grinding marks. The specimens were than pulled :it 2 1/2 pct per rnin in an Instron testing machine. The tantalum specimens were tested at 77", 195", and 300°K. The alloy was tested at 300°K only. All specimens exhibited a yield-point phenomenon at all temperatures. Typical load-elongation curves at the three test temperatures are shown in Fig. 1. The lower yield stress is plotted as a function of (grain size) in Figs. 2 and 3 for tantalum and the 90 pct Ta-10 pct W alloy, respectfully. The position and slope of the curves was determined by least-

Jan 1, 1962

By John Chipman

IT has been long known that the gas evolved during the boil in the open-hearth furnace is mainly carbon monoxide associated with smaller quantities of other gases. A number of attempts have been made to determine the precise effects of carbon and oxygen content of the bath, and of other factors, such as temperature, upon the evolution of carbon monoxide. In his investigation of the carbon-iron oxide product in liquid steel, Herty1 showed that the value of this product at equilibrium could be approximated by plotting the value of the product observed in open-hearth reactions against rate of carbon elimination, and extrapolating to zero rate. The results of this study showed a slight but definite effect of temperature upon the carbon-iron oxide reaction. Experimental studies of the evolution of gases from rimming-steel ingots have not yet attained the degree of precision necessary for an exact understanding of the effects of pouring temperature, carbon content, and iron oxide in the metal upon the composition of these gases. Klinger2 showed that the gas consists mainly of carbon monoxide, and that con-siderable variation in its composition occurs during the solidification of the ingot. In order that these variations may be understood in their proper relationship to the progress of solidification of the ingot and the segrega-tion that accompanies solidification, it is essential to have a knowledge of the condition of equilibrium in the several chemical reactions by which the gases are being formed. It is also necessary to understand the effects of temperature upon the equilibria, and further, to know the manner in which the temperature of the liquid metal within the ingot changes as the skin of the ingot is being built up. The reactions in which we will be chiefly interested are those involving in the one case the oxides of carbon, and in the other case steam and hydrogen, with iron oxide and carbon in the liquid metal. The reactions as they occur in unalloyed liquid iron, and their respective equilibrium constants are written as follows:

Jan 1, 1937

By D. M. Kehn

A method has been devloped for chromatographic analysis Of the vapor and liquid phases Of a a system containing methane to components having 20 or more carbon atoms. The method uses a windowed equilibrium cell in which volumetric phase behavior of the system can be observed accurately and from which small samples of gas or liquid can be withdrawn for analysis. Analyses are made using two chromatographs, one for the lighter and one for the heavier components in a sample. Combination of the two analyses yields a detailed analysis of the gas or liquid sample. The complexity of the condensate heavy ends is evident from the chromatograms of these fractions, and the predominance of the paraffin hydrocarborn serves as a useful marker in interpreting the chromatograms. The K-values obtained in this analytical method are presented for a high-pressure condensate system and predict closely the observed volumetric behavior of the system. INTRODUCTION Quantitative analysis of hydrocarbons from natural gas reservoirs is necessary for several reasons—to calculate the amount of sales gas produced, to calculate the amount of natural gasoline produced, to plan a liquid recovery system, or to calculate the potential economic value of a reservoir produced under one or more of several different conditions. Analysis of natural gas fluids produced to the surface consists of identifying and computing the mol fraction of each component of the mixture. Although methane is the predominant component, varying amounts of ethane, propane, butane, pentanes and heavier components are also present. Materials containing up to 30 carbon atoms occur in amounts which decrease with increasing molecular weight. However, the quantities of components in the 20 to 30 carbon atom range are usually so small that their importance is negligible, and they are undetect-able in natural gas by ordinary analytical methods. All the components up to those having 20 carbon atoms may sigsficantly affect phase behavior, however. Commonly, only the methane-through-pentane fraction is analyzed quantitatively for each component, while components heavier than Pentane are lumped and repored as "hexane- plus". Expensive, tedious techniques are required for analysis of this fraction. Consequently the detailed analyses needed for prediction of reservoir behavior are usually undertaken only when major gas fields are being developed. The need for complete analyses of condensate systems is apparent when it is recalled that most gas fields are produced by pressure depletion. As the pressure declines, some of the heavier hydrocarbons are lost as liquids which are in the reservoir. In many instances the amount of liquid in equilibrium with the gas phase at high pressure constitutes only 1 or 2 mol per cent of the total system. Flash calculations generally must predict the actual amount of liquid with an accuracy of a few per cent in order to be useful. This retrograde condensation has been understood for years, but accurate correlation methods to permit quantitative prediction of phase behavior in the retrograde region are not presently available. The increasing importance of natural gas has made accurate prediction of phase behavior and composition of produced natural gas streams an economic necessity. The work reported here was undertaken to provide a rapid, economical method for obtaining the vapor-liquid equilibrium information needed to predict accurately the composition of the fluids produced from a gas reservoir throughout its life. TO develop this method, a pressure cell equipped with windows was designed and built for observing the volumes of liquid and gas present at reservoir pressures and temperatures. Use was made of established chromatographic methods for rapid and detailed analysis of both phases. This paper describes the equipment and techniques developed for obtaining vapor-liquid equilibrium data, presents the results of analyses of a condensate system, and indicates the usefulness of these data in predicting hydrocarbon phase behavior. DESCRIPTION OF EQUIPMENT USED The equipment used in obtaining the required information on phase behavior and the complete analysis of hydrocarbon mixtures through C, will be described first, followed by a discussion of the operation of the equipment. It will be helpful, however, to consider first a brief outline of the technique used. A sample of separator gas and liquid is charged to the windowed cell (see Figs. 1 and 2) where volumetric equilibrium phase behavior at reservoir pressures and temperatures can be determined. Then samples of the coexisting phases are withdrawn. The methane-through-pentane fraction is analyzed with a chromatograph equipped with a hot-wire detector, and the pentane-plus fraction is analyzed with a second chromatograph equipped

Jan 1, 1965

By J. L. Keats

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical characteristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained. THE TEST HEAT The test heat was made in a standard 100 ton stationary furnace at the Lackawanna Steel Co., Lackawanna, N. Y. on January 17, 1922. The Charge-Scrap.-The scrap consisted entirely of rail-heat butts, selected from a number of heats made, the week before the test. The average analysis of the scrap was calculated from the analysis of these heats-and from the weight of scrap from each heat. Pig Iron.-Two ladles of pig iron were used in the charge and two samples were taken from each ladle as it was poured into the furnace. These four samples were composited for the average pig-iron sample.

Jan 2, 1926

By Curtis L. Graversen, J. H. Hamilton, John C. Nixon, John R. Lewis

RECENTLY there has been much speculation concerning the advantages of using oxygen enriched air or pure oxygen in pyrometallurgical processes. The advantage of using oxygen in the iron blast furnace and elsewhere in ferrous production metallurgy has been given careful consideration and, as a result, several experiments have been tried and a number of papers have recently appeared on this subject.1.2 The use of oxygen in nonferrous smelting likewise poses interesting problems, therefore any experimental data obtained in this area should likewise be of general interest.3 Ashcroft4 in 1933 claimed to have obtained improved results when copper concentrates were roasted in pure oxygen. However, his' paper gives neither data nor experimental details. A few years ago a research program was started in this laboratory which had for its objective the determination of the mechanism of oxidation of metallic sulfides under varying conditions. To date we have studied the oxidation of galena, 5 sphalerite, and chalcocite. It is a well known fact that copper sulfide minerals are oxidized slowly by weathering agents, so that the sulfides of copper which find their way into a tailing pond are gradually changed into watersoluble and acid-soluble compounds. Commercially, the oxidation of copper sulfide minerals is accomplished by roasting them at elevated temperatures in air using a suitable (usually multiple-hearth) roaster. Most copper smelters are equipped with such roasters. In this phase of the study we were especially interested in determining the effect of temperature on: (I) the air oxidation of chalcocite and (2) the oxidation of chalcocite using commercial oxygen. The amount of sulphur removed as sulphur dioxide, the percentages of water-soluble copper, and of acid-soluble copper were determined for the air oxidation tests. In the tests using commercial oxygen, the percentages of sulphur dioxide, water-soluble copper, acid-soluble copper, water-soluble sulphur and acid-soluble sulphur were determined. For these experiments the temperature was varied from 250 to 700°°C. EXPERIMENTAL Preparation of Chalcocite (Cu2S) Natural chalcocite is not pure. Minerals such as bornite, covellite, and chalcopyrite may be present. It was decided, therefore, to prepare some chalcocite in our own laboratory. An intimate mixture of sulphur and finely divided metallic copper in the ratio of 4 g of copper to I g of sulphur was prepared. To this was added a slight excess of

Jan 1, 1948

By W. Bonfield

The temperature dependence of the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.) and the stress-plastic strain curve of polycrystalline Cu 1.9 wt pct Be have been measured for the solution treated condition, an intermediate condition containing G.P. zones and ?' precipitate and the overaged ? precipitate condition, in the range from -58° to 200° C. A transition in micro -yield behavior and a large temperature dependence were noted for the intermediate condition, which are interpreted in terms of the interaction of glide dislocations with two differently sized zones. In comparison the microscopic yield stresses of the solution treated and overaged conditions were less sensitive to temperature variations and are satisfied by the Mott-Nabarro and dislocation bowing theories, respectively. A determination of the temperature dependence of the yield stress of a precipitation hardening alloy has provided a powerful tool for evaluation of the operative deformation mechanism. There is a marked contrast between the effect of temperature on the yield behavior of a metal containing coherent zones or intermediate precipitates, which can be "cut through" by mobile dislocations, and a metal containing a dispersion of noncoherent particles, through which dislocation "bowing out" is the dominant role of deformation.' These studies have in general been confined to single crystals, as it was considered that similar experiments on polycrystalline material did not produce good data because of the lack of sensitivity with which the yield stress could be determined. However, this objection has been removed by the introduction of mi-crostrain techniques, with which the yield stress in polycrystalline materials can be measured to a strain sensitivity of 10-6. Such measurements have not only shown that the deformation of polycrystalline precipitation hardening alloys can be examined with the same detail as single crystals, but also that some unexpected results are obtained.' In this paper the results obtained from a study of the temperature dependence of the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.) and the stress-plastic strain curve of a polycrystalline Cu 1.9 wt pct Be precipitation hardening alloy (Berylco 25) are discussed. The temperature dependence of the alloy was measured for three different conditions: 1) The solution treated condition (a supersaturated solid solution of a containing ~12 at. pct Be3) which is obtained by water quenching the alloy from 800° C. 2) The condition of y' intermediate precipitate, to- gether with some G.P. zones,' which is produced after an aging treatment of 2 hr at 315°C from the solution treated condition. (The alloy was cold rolled to 40 pct reduction prior to aging to minimize grain boundary precipitation effects.)4 3) The condition with equilibrium ? precipitate structure2 which is developed after an aging treatment of 24 hr at 425° C. EXPERIMENTAL PROCEDURE Tensile specimens of gage length 1 in. and with rectangular cross section of 0.18 by 0.06 in. were prepared from the solution treated, cold rolled alloy and were either resolution treated for 1 hr at 800°C, followed by water quenching, or aged for 2 hr at 315°C and 24 hr at 425° C to produce the desired precipitate structures. The microstrain characteristics of the aged specimens were determined at temperatures from —58" to 200° C and those of the solution treated specimens from -58° to 30° C. Each temperature was controlled to ± 0.2°C, which was a level of stability sufficient to eliminate thermal expansion effects from the measurements (~1.2°C temperature increase produced an extension of 2 x 10-6 in.). The microplastic behavior of the specimens in the temperature range below 82" C was measured with a standard Tuckerman strain gage,5 while at temperatures above 82°C a modified Tuckerman gage with a reduced strain sensitivity (4 x10-6 in. per- in.) was used. A load-unload technique was used to establish values of the microscopic yield stress. The specimen was strained at a constant cross head speed of 2 x 10-2 in. per min to a given stress level, at which the total strain was measured. Then the specimen was immediately unloaded at the same rate and any residual plastic strain determined. This procedure was repeated for an increasing series of stress levels until the microscopic yield stress was established by a direct measure of the stress to produce a residual plastic strain of 2 x 10-6 in. per in. (It should be noted that, as reversible dislocation motion occurs at stresses less than the microscopic yield stress,2 the plastic strain rate at this level was not constant.) In an ideal test, the microscopic yield stress would be determined from a continuous stress-strain measurement, rather than from a load-unload sequence, in order to eliminate mechanical recovery effects.6 However, it was found experimentally that mechanical recovery was negligible in Cu 1.9 wt pct Be at small plastic strains for all the temperatures investigated, as the microscopic yield stress was independent of the number of load-unload cycles employed (i.e., the values measured for specimens subjected to different numbers of cycles was within the experimental scatter determined for specimens tested in an identical manner). Therefore, it is reasonable to consider the microscopic yield stress determined in the load-unload

Jan 1, 1969

By Frank M. Randall

The Buick mill is located at the site of the old Buick general store, approximately 4 miles south of Bixby, Missouri on route KK. It is a part of the operations in the area now called the "New Lead Belt". The ore body lies at an elevation of 270 feet above sea level, and is fairly flat lying, becoming slightly deeper toward the south. The mineralization is due to the secondary deposition of galena, sphalerite, chalcopyrite, pyrite, calcite, dolomite and some localized drusy quartz in a country rock of dolomitic limestone. The galena is fairly coarse grained with some large crystaline structure, and some oxidized surfaces. The sphalerite is fine grained- small crystals containing Cd (about 0.7%) and Ag (about 10 oz per ton) in solid solution. The chalcopyrite is fine grained, fine crystals that are sometimes massive in nature. The mine plan is a modified room and pillar system. Broken ore at the mine face will be transported to several different ore passes by rubber tired load-haul-dump units. Ore passes will drop the ore to a rail haulage level some 90 feet below the mining level where bottom dump cars will deliver it to a 42 in. Nordberg gyratory crusher. Two 12 ton capacity skips in balance carry the ore some 1,200 feet to the surface. The hoist is equipped with automatic controls for loading, hoisting and unloading.

Jan 1, 1970

Jerome L. Boyer, Reading, Chairman; William L. Sheafer, Pottsville, Secretary ; Levi Quier, Reading, Treasurer; Robert Allison, Port Carbon; James Archbald, Jr., Pottsville; William Atkins, Pottsville; D. P. Brown, Lost Creek; William McH. Boyer, Rending; Albert Broden, Reading; George Brooke, Birdsboro; Frank Carter, Pottsville; H. P. Cooper, Pottsville ; J. H. Carpenter, Reading; E. S. Cook, Pottstown; B. Halberstadt, Pottsville; Hakon Hammer, Pottstown; J. Hartshorne, Stowe; M. P. Janney, Pottstown; R. C. Luther, Pottsville; N. Muhlenberg, Reading ; W. H. Morris. Pottstown ; George L. Norris, Reading; G. H. Potts, Pottstown ; H. Potts, Pottstown; S. M. Riley, Ashland ; J. S. Robeson, Pottstown ; Jas. P. Roe, Pottstown; A. W. Sheafer, Pottsville; Heber S. Thompson, Pottsville; Bard Wells, Pottsville; E. C.Wagner, Girardville; N. B. Wittman, Birdsboro. Reception Committee.— George Brooke, Chairman; Robert Allison, J. H. Carpenter, Edgar S. Cook, R. C. Luther, W. H. Morris, H. S. Thompson. Hotel Headquarters.—The Neversink Mountain Hotel, near Reading, Pa. All sessions were held in the hotel. The opening session was held on Tuesday evening, October 11. Mr. Jerome L. Boyer, Chairman of the Local Committee, called the meeting to order, and introduced Mr. John F. Daniel], Jr., VicePresident of the Reading Board of Trade, who delivered an address of welcome, in the course of which the industrial and commercial importance of the city was effectively outlined by skilful use of the statistics of leading branches. From this statement the following particulars are condensed for preservation: The Board of Trade has about 300 members. The annual value of the manofttctures (taking mainly the figures of 1891) is as follows: Iron manufactures, about $16,000,000 (including boilers and flues, $323,000; hardware, locks and butts, $1,650,000; pig-iron, wrought-iron pipe and machinery, $8,400,000; beams, bridge-work and steel, $4,000,000; bolts, nuts, rivets, etc., $1,000,000; stoves, $659,000); silk and cotton goods, $1,725,000; boots and shoes (one concern only), $150,000; ropes and cordage, $600,000; fire-brick, terra-cotta and glass, $320,000; wool and fur hats, $3,000,000; cigars (105 millions), upwards of $3,150,000. The street and elec-

Jan 1, 1893

By W. R. Bendy

GRINDING is a large and costly part of Portland cement manufacture. Prior to clinkering in the rotary kiln, raw materials are ground to a fineness of 80 to 90 pct passing 200 mesh. Then, after burning and cooling, the resulting clinker is ground to about 92 pct passing 325 mesh. In the cement industry the most favored method of grinding has always been by impact and attrition of a ball charge in a rotating mill. Other types of mills, in which materials are ground between die rings and rollers, or between die rings and large balls, are sometimes used for single-stage grinding and often for preliminary grinding followed by grinding in ball-type mills. Their efficiency is usually high, but maintenance and repair costs are high also, and the ball-type mill continues to be the most widely used. Together with 4 pct gypsum to retard setting time, the kiln run clinker—consisting of hard, semi-fused lumps that may have been crushed to — 1/2 in.—is ground to a Blaine surface area of 3000 sq cm per gram and about 92 pct passing 325 mesh. Approximately 32 kw-hr per ton, or 6 kw-hr per 376-1b barrel, are consumed in the grinding mills alone, not counting auxiliaries. Open Circuit Clinker Grinding: Many early clinker grinding plants employed two-stage, open circuit grinding. Comparatively short mills of large diameter, loaded with balls 4 in. and smaller, first reduced the clinker to 95 pct passing 14 mesh. Tube mills of smaller diameter and greater length, loaded with balls 11/4 in. and smaller, carried out the fine grinding operation. An early development was to assemble two or more stages of grinding in a single mill having two, three, or four compartments separated by division heads. There were difficulties in balancing the compartments, but compartment mills were popular in the 1920's because the layout was simple and there were no elevators and conveyors. Oversize Particles: Open circuit mills, whether separate ball and tube mills or compartment mills, always encountered the problem of tramp oversize in the product. A small percentage of clinker survived passage through the first grinding stage as particles—perhaps 1/16 in. diam—that were too large for the smaller balls in the following stages to reduce to —200 mesh. When the feed rate was lowered to reduce tramp oversize, there were serious losses in grinding efficiency. Many ingenious designs were perfected to incorporate perforated screen plates or wire mesh screens in the ball mills or in the first compartments of compartment mills. Their purpose was to prevent mate: rial passing out of the first stage until it was small

Jan 1, 1958

By P. E. Senseny

INTRODUCTION Massive hydraulic fractures have been used since 1949 in the petroleum industry to enhance production rates and increase recoverable reserves. Currently, a research program, the Multi-Well Experiment, is underway to develop the understanding and technology to a1 low economic production of the large gas reserves of the low permeability, lenticular sandstone formations in the western U.S. (Atkinson, et al, 1981; Northrop and Sattler, 1983). Use of state- of-the-art hydraulic fracturing techniques is a part of this investigation. As a portion of an extensive core program in support of this experiment (Sattler, 1983), fracture toughness has been determined for 56 sandstone, shale, mudstone, or siltstone horizons from three wells in the Piceance Basin. The role of fracture toughness in hydraulic fracturing is not well understood because other factors, such as in situ stress, dominate fracture geometry and containment. Rubin (1983) concluded from analysis of his laboratory hydrofracture experiments that fracture toughness should be included in design and numerical simulation of hydraulic fractures. However, van Eekelen (1982) contends that the stress intensity at the crack front should be so much greater than the fracture toughness of the rock that toughness can have no importance. Generally, fracture toughness and other material properties, such as elastic moduli and permeability, are thought to be of secondary importance in determining fracture geometry and containment. In spite of this, there is a need to acquire a more quantitative understanding of their importance for accurate design and simulation calculations. Analysis of fracture geometry and containment data from hydraulic fracturing experiments carried out in formations where fracture toughness and other rock properties are

Jan 1, 1984

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

By B. H. Kear, B. J. Piearcey

The orientation and temperature dependence of the tensile and creep propevties oj Mav-M200 crystals halle been determined. Crystals oriented for single slip exhibit ,maximum ductility, minimum work hardening, and least creep resistance, whereas crystals in multiple slip orientations show nzinimu~n ductility, strongest work hardening, and greatest creep resistance. At 1400" and 1600°F there is a marked improzlenzent in creep strength for orientations approaching [001] and [111], indicating that interactions between dislocations gliding in intersecting octahedral slip systems play an important role in creep resistance. At 1800°F the creep strength is much less dependent on orientation, which is rationalized in terms of slip in cube planes as well as octahedral A frequent mode of failure in high-strength cast nickel-base superalloys is by intergranular fracture, particularly along those grain boundaries oriented transverse to the major stress axis. VerSnyder and ~uard' demonstrated that this problem could be overcome by eliminating transverse grain boundaries through unidirectional solidification. Piearcey and versnyder2 made use of this principle in the development of unidirectionally solidified gas turbine blades and vanes, where the growth direction of the columnar grain structure coincides with the axis of principal stress under operating conditions. The present investigation was undertaken to determine if further improvement in properties may be obtained by eliminating grain boundaries altogether, so as to take advantage of the well-known dependence of mechanical properties of single crystals upon the orientation. 1) EXPERIMENTAL PROCEDURE Single crystals of Mar-M200* were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold, and crystal growth was promoted from one end by appropriate gradient cooling. Tensile and creep specimens (2 in. diam by $ in. gage length) were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. The orientations of the specimens were determined by the Laue X-ray back-reflection method. Tensile tests were carried out in aWiedemann machine with furnace attachment, using a strain rate planes. In all orientations imzpvouement in the strength charactevistics of the material can be induced by heat treatment. Creep ad stress rupture data for (001) oriented crystals are compared with similar data obtailted previously joy random polycvystalline material, and also columnar grained material having a prejevved (001) orientation. The single-crystal )material exhibits both longer rupture life and lower minimum creep rate at all temperatuves, and the rupture elongation is comparable with that in the columnar grained material. From these results it is concluded that single crystals should and useful application in gas-turbine blades and tanes. The optimum orientation for a blade is considered to be with its axis of principal stvess parallel to (001) ou (111). of 0.0001 sec-'. Load and extension were recorded directly on an X-Y recorder. The strain measuring device consisted of extension arms attached to the grips at one end and leading out of the furnace to an LVDT (linear variable differential transformer) at the other. Creep tests were performed using a standard constant load creep frame. 2) DISCUSSION OF RESULTS 2.1) Structure of Alloy. The structure and segregation in as-cast and heat-treated Mar-M200 has been described in detail else where.~ The main features are as follows: the as-cast material is heavily cored, due to pronounced dendritic segregation during solidification; the dendrites are rich in tungsten and cobalt whereas the interdendritic regions are rich in chromium, titanium, nickel, and carbon. The structure consists of -60 vol pct coherent precipitate of y', basically Ni3(A1,Ti), in a matrix of y (nickel-base solid solution), interspersed in the interdendritic regions with minor MC carbides and -y' eutectic. The y' particles, and y-y' eutectic, contain more titanium, aluminum, and nickel, and less tungsten, cobalt, and chromium than the y matrix. Heat treatment partially removes segregation, eliminates the eutectic, refines the y' dispersion in y, and gives additional partially coherent M23Cs carbide. An as-cast crystal, therefore, is composed primarily of two oriented phases (y + y'), whereas the normally heat-treated crystal consists of three oriented phases (y + y' + MZ3Cs). Typical electron transmission micrographs of the y + y' structure are shown in Fig. 1. Crystals grown in the (100) orientation develop a simple unidirectional dendritic structure, Fig. 2, since (100) happens to be the preferred direction of growth for dendrites in this material. Crystals grown in the {110) and (111) orientations, however, tend to promote equal growth, generally in separate colonies, in the two and three geometrically favored (100) growth directions, respectively. In other orientations of growth, a single (100) dendrite direction generally pre-

Jan 1, 1968

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties situated at 29 West 39th Street in New York City United Engineering Trustees, Inc. When Mr Carnegie made his gift, "for the erection of a suitable union home" for the engineering societies, United Engineering Trustees, Inc (then United Engineering Society) was chartered un¬der Chapter 703, Laws of the State of New York, 1904, for "the advancement of the engineering arts and sciences in all their branches, and to maintain a free public engineering library " The Corporation was further empowered to acquire real and personal property and to use, maintain and occupy it, with the provision that any building erected by the Corporation shall be used perpet¬ually as a meeting place and headquar¬ters for the Founder Societies Thus the Carnegie gift realized the ideal of bring¬ing the engineering societies together under one roof, and the Corporation through its members nominated in equal numbers by the four Founder Societies had the necessary authority to act for the Founder Societies in their joint in¬terests in owning and operating for them not only Engineering Societies Building, but in the course of time, Engineering Societies Library, and The Engineering

Jan 1, 1952

By Joseph S. Malesky

As essential as the discovery of coal was to our state of advancement, the discovery and development of explosives marks one of the most important findings in the history of civilization. For this reason explosives are rightfully referred to as the forerunner of progress. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. An explosive may be defined as a substance (usually a mixture) that, where flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1973

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By B. H. Caudle, W. J. Bernard

Factors which influence the success or failure of a waterflood can seldom be determined in the laboratory. For this reason pilot waterfloods are initiated in a repreventative portion of the oil reservoir in question. For a pilot flood to predict quantitatively the recovery to be expected in a field-wide waterflood operation, the pilot area must behave as though it were confined (surrounded by similar areas). In this study, laboratory fluid-flow models were used to determine the simplest pilot pattern, for particular conditions of mobility ratio and initial gas saturation, that would behave as though it were confined. Pilot patterns studied ranged in complexity from a single inverted five-spot to a grouping of nine regular five-spots. Only the innermost producing well in each pattern was studied. Model results showed that the optimum number of wells in the pattern depends upon the oil-water mobility ratio and the expected oil-bank size. Unfavorable mobility ratios will, in general, require more wells in the pilot pattern than will favorable mobility ratios. Pilot patterns in reservoirs which contain a dispersed, flowable, free gas saturation will require fewer wells than for the under-saturated case. The single inverted five-spot pattern was found to be unsatisfactory for predicting behavior of fully developed waterfloods. In particular, it is possible that, in reservoirs which contain a flowable, dispersed gas phase, the oil bank will never be observed at the producers due to the large amounts of free gas which continue to be produced with the oil. INTRODUCTION One method which has been used to predict the performance of a waterflood is the pilot flood. The pilot waterflood is a flood which involves only a small cluster of the reservoir wells and is located in a small, representative portion of the reservoir. The object is that oil produced from the pilot can, in some way, be related to the oil recovery to be expected from a field-wide expansion of the waterflood. However, these field pilot waterfloods have often been unreliable in the prediction of oil recovery in a fully developed waterflood. This unreliability has also been demonstrated in several laboratory studies of pilot floods. Some of the investigators have shown that there are situations in which the pilot flood oil production is far too optimistic with respect to the oil recovery in the fully de- veloped flood. Others4-G have shown that the pilot results can also be pessimistic, especially if the pilot waterflood is initiated in an oil reservoir which has been depleted by primary recovery and is at very low pressure. The major reason for this unreliability of pilot water-floods is the migration of fluids into or out of the pilot area. By the well-known method of images, if straight lines can be drawn to represent vertical planes of symmetry in a porous medium which contains pressure sources and sinks (injectors and producers), then these lines are invariant streamlines, or lines across which there is no potential gradient, and therefore no flow. In an actual reservoir, these lines of symmetry can never be established exactly because of reservoir inhomogeneities and irregular reservoir boundaries. However, if the reservoir is relatively large and contains wells in repetitive patterns, these lines of symmetry are commonly assumed to exist for the pattern units sufficiently far removed from the reservoir boundary. Lines of symmetry for the five-spot injection pattern are shown in Fig. 1. Each five-spot unit in this figure can be considered confined with respect to flow across its boundary. In pilot floods this is not the case. The lines of symmetry for the pilot patterns investigated in this study are shown in Fig. 2. It is obvious that the fluid within these pilots is not confined and is therefore able to migrate into or out of the pilot area. Intuitively, one can see that, if more wells are added to the pilot, the innermost unit tends to behave more and more like the confined pattern. However, there is a practical limit to the number of wells which should be placed in the pilot. This limit is usually determined by economic factors. It was the purpose of this study to use laboratory fluid-flow models to determine which of the previously mentioned pilot patterns will force the innermost producing well to behave as it would in a fully developed waterflood. Since fluid migration is influenced by initial saturation conditions and the mobility ratio, these factors were included in the study. The ultimate objective of this study was to develop data which would allow the operator to choose a pilot pattern and operating conditions that will yield a production history which can be applied directly as an estimate of the performance of each production well of the fully developed waterflood. BASIS FOR THE STUDY The basic problem of field pilot floods is the migration of the reservoir fluids into or out of the pilot area. This problem has been the subject of previously reported model studies on pilot floods. These studies have been concerned mainly with the development of arbitrary "correction factors" to be applied to the simple, unconfined pilot systems such as the single five-spot. The correction factors were intended to adjust the production history of the un-

By William E. Bonini, Eugene A. Hickok

IN the course of an investigation directed toward expanding ground-water facilities in Essex and Morris counties, New Jersey, the Board of Water Commissioners of the city of East Orange authorized a seismic-refraction survey1 for the purpose of delineating bedrock topography below unconsolidated overburden. Results of the survey were highly satisfactory and led to the preparation of a comparatively detailed bedrock contour map. Knowledge of the bedrock depth and configuration was an important aid in selection of sites for test drilling. The portion of the East Orange Water Reserve under consideration is in the flood plain of the Passaic River about 10 miles west of Newark, N. J. The flood plain is about 175 ft above mean sea level and is bordered by low hills rising to elevations of approximately 250 ft. The bedrock underlying the Water Reserve consists of sandstone and shale of the Triassic Brunswick formation and is covered everywhere by deposits of unconsolidated glacial outwash sand and gravel, lacustrine clay, and recent river silt as much as 150 ft thick. Yield of wells in the sandstone and shale averages 100 to 200 gpm. Since production wells constructed in the sand and gravel aquifer in the buried river valley shown on the contour map (Fig. 1) yield 300 to 1400 gpm, it was proposed to locate additional production wells in this buried valley, where the yields per well would be maximum.

Jan 4, 1958

One of the very simplest losses to overcome, and at small expense, is belt slip. To show the extent of the loss of money through slipping of the main belt alone, a chart, supplied us through the courtesy of the Cling-Surface Co., Buffalo, N. Y., is shown herewith, upon which this is easily ascertained. By glancing up and down column "D" of this chart it is evident that the "Cost of Avoidable Belt Slip per Year in Dollars" may vary all the way from the smallest sums into the thousands of dollars. Roughly, 2 per cent. of the potential power in the driving pulley of the engine is represented by "belt creep." Its loss is unavoidable because of the elasticity of the belt. This has been recognized and provided for in the chart, so the reader can go ahead and connect known values, while the intersection with column "D" gives the avoidable money loss. Simply zig-zag across the chart twice with a straight edge, as shown by the dotted lines and the money loss is immediately found. Thus if the total belt slip is 6 per cent. (column A) and the cost of coal per ton is $4 (column B), run a straight line through those two points and locate the intersection with column "C." Then from that point of intersection run over to the tons of coal burned per year (which in this instance has been stated as 1000 tons) and the cost of avoidable belt slip per year is shown by column "D" as being $160. To give a clear idea as to the meaning of "Total Belt Slip Per Cent." let us take an example. You find by means of a revolution counter that a given driven pulley is rotating only 940 times per minute. You figure that without slip it should rotate 1000 times per minute; 60 revolutions per minute, therefore, are absolutely lost. Dividing this 60 by the r.p.m. that pulley should make you get 0.060 or 6 per cent. which is the "Total Belt Slip." After having made this determination, it is a simple matter to apply it to the chart as has been done and determine the money loss per year due to such slip.

Jan 4, 1918

By J. B. Fisken

(Butte Meeting, August, 1913.) BEFORE touching upon the immediate subject of this paper a few facts of a historical nature as to the general application of electricity to mining might be of interest. As to what was actually the first application of electricity to mining, opinions will no doubt always differ. My experience does not go back far enough, nor are the records to which I have had access of any value as covering this point. Sydney F. Walker, a man whose pioneer experience in the application of electricity to mining purposes dates back as far as 1876, ,gave an interesting resume of the subject in an address before the South Wales branch of the Association of Mining Electrical Engineers at its 1.913 session, and, unless his statements are shown to be wrong, they should be accepted as facts. According to Mr. Walker, the ignition of charges of blasting powder was the first operation in mining to be accomplished with the aid of electricity. Very frequently this energy was furnished by a static machine and occasionally by a magneto generator. Later, this was followed by the application of electricity to bell signals, and we are told that this application was looked upon skeptically and regarded as an expensive experiment by the mining managers of those early days. At the Paris Exposition of 1878, there was exhibited an electric lamp, which suggested future possibilities to the mining engineers of those days. The first successful application of electric lighting to underground excavations that I have been able to find any record of is that of M. Blavier. In the year 1879&apos; he installed two Serrin lamps and successfully illuminated one of the large underground chambers in the Angers slate quarries. Another early application of electricity to the lighting of mines is that in the large chambers in the salt mines of Maros-Ujvár, in Hungary; these have been regularly and successfully lighted elec-

Jan 6, 1913

By A. Raman

The Nb-Co system was nuestigated in the range 10 to SO at. pct Co with X-rays. A pt phase with the W6Fe.r-type structure occurs in the system between 46 and 52 at, pct Co. Its unit-cell dimensions are nearly identical to those of the p Phases found in the Nb-Fe and Nb-Ni systems. Two Laves phases, one having the MgZnz-type structure and the other the MgCuz-type structure, already t-eported in the literature, are found to exist in the system. The ,l.IgZnz-type phase occurs between 62 and 64 at. pct Co. A MgNi2-type Laves phase, reported in the literature, is no! obtained. A binalry phase is found to exist belozv I000C around 82 at. pct Co. THE cobalt-rich side of the system Nb-Co has been repeatedly investigated by previous inestiators" and the following intermediate phases are known to occur: NbCo, which crystallizes in the MgCu2-type structure and Nbc03,&apos; reported originally by Wall-bam, which has the MgNiz-type structre. Jordan and uwez&apos; as well as lliott&apos; were unable to find the MgNiz-type phase. Two phases, designated as x and y, were reported by Saito and eck.&apos; The phase x was inferred to have a narrow composition range near 77 at. pct Co. No published work is known to the author which reports the investigations in the niobium-rich portions of the system. This paper presents the results of an investigation in the Nb-Co system between 10 and 80 at. pct Co. EXPERIMENTAL PROCEDURE Two or three grams of the alloys under investigation were prepared using niobium (99.9 pct +) and cobalt (98.8 pct + with 0.14 pct Fe and and 0.03 pct C) in a tungsten-electrode arc furnace under commercial argon atmosphere. They were then wrapped in molybdenum sheets and annealed for a period between 5 days and 1 week at 1300°C in high vacuum (10-" orr) or in evacuated quartz amules for 2 weeks at 1000°C. Powders of -325 mesh size were prepared for X-ray work by crushing and grinding the specimens. Subsequent reannealing of the powders was not undertaken since most of the alloys were brittle and broke easily. X-ray powder patterns of the as-cast and annealed samples were prepared in a Siemens cylindrical camera (57.3 mm radius) with Cr-K, radiation. A Siemens diffrac to meter was used to get the X-ray patterns of some new phases. Metal log raphic examination of the alloys supplemented the X-ray findings. RESULTS The results of the X-ray and microstructural analysis Of the alloys are in in Table I. The lattice parameters of the phases are listed in Table 11 for quick reference. A set of micro photographs in Fig. l(n) to (j) show the microstructures of some alloys. A probable equilibrium diagram is drawn in Fig. 2

Jan 1, 1967