Search Documents

By E. W. Dewing

ROLIN1 in 1961 published a phase diagram for the CaF2-Na3AIF6 system in which substantial (-20 wt pct) solid solubility of CaF2 in Na3A1F6 at the eutectic temperature (945°C) was indicated. The evidence was that the halt in cooling curves associated with the eutectic was lowered progressively on the Na3AlF6 side. H olm2 has recently confirmed the experimental fact, but attributes it to evaporation losses shifting the composition into the ternary NaF-CaF2-Na3A1F6 system with a consequent lowering of the eutectic temperature

Jan 1, 1970

By Bernhard Blumenthal

A melting process was developed by which high purity electrolytic uranium crystals can be converted into sound ingots without serious contamination. Careful preparation of the crystals, melting in a high vacuum, and directional solidification led to a metal of better than 99.993 wt pct purity. The metallographic examination showed a substantially clean metal with only residual amounts of a second phase which responded to heat treatment. The density of high purity uranium is 19.05 g per cu cm. FOR the study of the fundamental properties of uranium and its alloys, a base metal of high purity is needed, and an investigation was started at Argonne several years ago to examine various methods of preparing high purity uranium. Early success was achieved by the fused salt electrolysis process in preparing high purity metal in crystal form,' and the problem became that of melting the crystals into ingots without contamination. The electrolytic crystals contained a few ppm of heavy metals, less than 15 ppm C, and large quantities of potassium and lithium in the form of trapped fused salt electrolyte. On melting in vacuo in magnesia or urania crucibles, the metal picked up considerable quantities of carbon and some iron, copper, and silicon but lost most of the potassium and lithium. It was not metallographically clean, and much research work was necessary to determine the optimum melting conditions for minimum contamination. This work has resulted in the development of a melting procedure by which sound ingots can be prepared with only a limited contamination by carbon. In the section entitled "Melting of the Electrolytic Metal," the equipment and processes that have been developed for melting the electrolytic crystals are described in detail. The "Metallography" section is devoted to the metallography of high purity uranium, and the section "Density of High Purity Uranium" contains the first property measurement on high purity uranium—a density determination. Melting of the Electrolytic Metal Apparatus—Melting and Vacuum Equipment: Uranium may be melted in either resistance or induction-type electric furnaces. Resistance heating was found to be preferable to induction heating for melting down the electrolytic crystals, for several reasons: Although induction heating permits fast heating, this advantage cannot be utilized when crucibles with limited thermal shock resistance are used. Temperature control of induction-heated melts is poor, and the stirring effect increases the rate of contamination of the melt from the crucible, slag, or the furnace atmosphere; liquation and controlled solidification are difficult to carry out. Because of these objections, resistance heating was chosen. A 10 kw Globar resistance furnace of low heat capacity permitted uniform heating of a uranium charge to its melting point in 45 min. The furnace was insulated with a removable aluminum shield so that, after melting and removal of the shield, the furnace could be quickly cooled to room temperature. The furnace was equipped with an apparatus for directional solidification; see Fig. la. The crucible was suspended in the center of the furnace; and when the melting was complete, the crucible was slowly lowered into the cold end of the furnace tube. Solidification took place upward from the bottom; and when the rate of lowering was small, a sound ingot free from sink holes and shrinkage cavities was produced. To remove the large quantities of gas contained in the electrolytic crystals, melting in a high vacuum is mandatory. While, from the standpoint of contamination, melting in a highly purified argon atmosphere appeared feasible, lithium and potassium removal proved less efficient under such conditions. Also, a vacuum-melted ingot has a cleaner surface than one melted in an inert atmosphere. The vacuum system must be of very high pumping speed and leak tight so that a vacuum of less than 2x10-7 mm Hg is attainable when the system is pumped down cold. The system must have a high pumping speed, so that the pressure maximum which may rise to 1x10-4 mm during heating can be quickly reduced

Jan 1, 1956

By R. F. Sheldon

The discovery of the Carlin deposit was the result of discriminating geologic research and prospecting devoted to the objective of finding a gold deposit that could be mined by open pit methods. By the late 1950s, Newmont Mining Corp. was becoming increasingly concerned about the trend of rapidly rising underground mining costs unless bulk mining methods could be applied. The desirability of finding an open-pittable gold deposit was apparent. The attention of Newmont geologists was directed to Nevada by the publication of two papers: "Paleozoic rocks in North-central Nevada" (1958) and "Alinements of Mining Districts in North-central Nevada" (1960), both authored or co-authored by Ralph J. Roberts of the United States Geological Survey. John Livermore, geologist of Newmont Exploration Ltd., attended a talk given by Roberts in Ely, Nevada in the summer of 1961. These papers and the address by Roberts gave details concerning the Roberts Mountain overthrust, a 483 km (300-mile) long, shallowdipping fault which pushed clastic and volcanic rocks of early and middle Paleozoic age eastward over younger marine formations. Subsequent uplift and doming with consequent erosion had locally removed the upper plate strata exposing windows of lower plate carbonate rocks. Roberts noted that the principal mineral deposits of the region, including gold, were associated with these windows which exhibited a preferred alinement. In the summer and fall of 1961 Newmont's exploration geologists John Livermore and J. Alan Coope began a systematic examination of gold occurrences associated with these windows, aided by further discussion with geologists of the US Geological Survey. Attention was directed to the Lynn and Carlin windows, particularly to those formations lying immediately above and below the Roberts Mountain fault. It was appreciated at the time that many of the gold occurrences in the region were unusual in that no colours were obtained even when panning high grade samples. A large number of rock samples were collected and analysed using fire assaying procedures, and background values for gold were established. This systematic rock sampling resulted in the identification of a distinct area of anomalous gold values, and a block of claims was staked in late October, 1961. These claims, plus an adjoining optioned 32.4 ha (80 acres) of ground, cover the main area of the present Carlin gold mine. Prior to snowfall that winter, one of the bulldozed assessment pits required to establish a claim's discovery exposed 24 m (80 ft) of mineralization assaying 0.007 kg/t (0.22 oz per st) gold. In the spring of 1962 a program of trenching, sampling, and geological mapping followed by rotary drilling was underway. Other properties in the area were acquired. The generally undistinguished nature of the dolomitic siltstones and silty dolomitic limestones hosting the micron-sized gold particles, coupled with the lack of visually associated guide minerals, made identification of the gold bearing areas very difficult. The entire drill column had to be assayed to ensure that values were not overlooked, as very often sections that might be assumed to be waste turned out to be high grade. On September 10, 1962 a high grade intersection of 24 m (80 ft) assaying over 0.03 kg/t (1 oz per st) gold was encountered in the third hole drilled. An expanded program of both rotary and diamond drilling led to the further delineation of the ore body. By December 1963, the exploration program had established an initial reserve of 10 Mt (11 million st) grading 0.01 kg/t (0.32 oz per st) gold. A 1.8 kt/d (2,000 stpd) processing plant was constructed and the first gold bullion was poured in May, 1965, just two years and eight months after the discovery hole was drilled. REFERENCES Roberts, R.J., Holz, P.E., Gilluly, J., and Ferguson, H.G., 1958, "Paleozoic Rocks in North-central Nevada," Bulletin American Association of Petroleum Geologists, Vol. 42, No. 12. Roberts, R.J., 1960, "Alinements of Mining Districts in North-central Nevada," Professional Paper 400-B, US Geological Survey, Article 9.

Jan 1, 1985

By John E. Young

U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow finger ridges and precipitous slopes, which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railrod cars. Lynch District selected diesel-powered locomo¬tives and 100-ton articulated cars capable of negotiating sharp curves. The drop¬bottom mine cars are equipped with longitudinally hinged doors that are auto¬matically opened and closed. Lynch District selected a large-diameter steel-lined borehole for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. Taking advantage of gravity, the presized coal is "lowered" vertically approximately 720 ft to existing entries of a previously abandoned mine. The coal is then conveyed horizontally into storage. The coal¬handling facility from the mine-car dump to the railroad load-out point is fully automatic through use of tone control. TV cameras are installed along the facility to continuously monitor the strategic points. The diesel locomotives are either directly operated or remotely radio-controlled, depending on the functions Per¬formed. U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slopes which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of under¬ground haulage and, thereby, presented the opportunity to use high-capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Wini¬frede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede mine coal-handling facilities. The Winifrede mine derives its name from the Wini¬frede Seam which comprises the total reserve recov¬erable from this facility. The seam is 5 ft high with a good siltstone bottom and competent shale or sandstone roof. The seam is at an elevation of 2700 ft where the mountain ridges are long and narrow. This configuration of the reserve was ideal for conveyor belt installation to transport the coal from the working face to the outside bench. The preclusion of underground rail haul¬age permitted an opportunity to review the type of locomotive power and to select high-capacity equipment without the limitations associated with underground systems. Since the basic electrical design of the mine was al¬ternating current, with rectification to direct current for shuttle cars required only in the face areas, there was no point in bearing the burden of additional cost of dc trolley installation. And, since the haulage would re¬quire only a few tunnels to negotiate sharp points and to reach the back side of the reserves, diesel power was selected for the haulage locomotives. To provide stability on the almost continuously curv¬ing track and to provide the maximum width of haul¬age equipment, both locomotives and mine cars, stan¬dard railroad gage was chosen to offer the largest choice of equipment. The decision was made to select a standard 45-ton railroad diesel locomotive but to lower the cab height to reduce tunnel excavation requirements. The mine car was the next challenge. Past experience in Lynch operations indicated that drop-bottom cars would be a successful application with the free-flowing coal. The search was for a drop-bottom car within the dimensions of the locomotive to discharge the coal in the shortest time. Numerous types were considered and visits made to various sites to observe cars in operation.

Jan 1, 1972

The following is am incomplete list of members and guests who called at Institute headquarters during the period May 10, 1918 to June 10, 1918. Arthur K. Adams, Potrerillos, Chile. J. M. Mahoney, Wilkinsburg, Pa. John Carter Anderson, Tucson, Ariz. Benjamin L. Miller, South Bethlehem, Pa. George S. Blair, Camp Cordon, Ga. Wilbur A. Nelson, Nashville, Tenn. W. A. Deane, Summitville, N. Y. Miles G. Nixon, Chicago, Ill. Charles H. Fulton, Cleveland, Ohio. Walter G. Perkins, San Francisco, Cal. Rudolf Gahl, Inspiration, Ariz. G. M. Ponton, Ottawa, Canada. C. C. Griggs, Eureka, Utah. D. A. Powell, Columbus, Ohio. J. F. Hanst, Potrerillos, Chile. H. W. Reed, Salt Lake City, Utah. Stanley C. Herold, Pittsburgh, Pa. J. C. L. J. Seelig, Padong, East. Indies. Floyd D. James, Boston, Mass. Oberlin Smith, Bridgeton, N. J. Charles Janin, San Francisco, Cal. Harrison Souder, Cornwall, Pa. E. Horton Jones, Copper Cliff, Ont. Stanley A. Spellmeyer, Camp Meade, Md. William Kelly, Vulcan, Mich. Roger S. Sperry, Waterbury, Conn. Ichiro Kitsunezaki, Tokyo, Japan. D. R. Thomas, Toronto, Canada. P. K. Lucke, San Antonio, Tex. Thor Warner, Phoenix, Ariz. E. Francis McCrossin, Birmingham, Ala. L. Douglass Anderson, formerly superintendent of the United States Smelting Co., Midvale, Utah, is now manager of smelters, Intermountain District, United States Smelting, Refining & Mining Co., Salt Lake City, Utah.

Jan 7, 1918

By Pradeep K. Rohatgi, Clyde M. Adams

An analysis of heal conduction in the freezing of a solution has been performed. The case considered is the semi-infinite mass of solution, bounded by a con-stant-temperature plane with one-dimensional heat flow, Numerical cooling rate and freezing rate distributions hare been calcutated for the particular case of unidirectional freezing of aqueous solutions against. a cold copper chill. The solution at each level parallel to the chill surface is subjected to a spectra of frcezing rates; the freezing rate is inilially lour., passes through a maximum, and then decreases until solidification is camplete. Arange and maximum freeeing rates are inversely proportional to the square of distance from the chill surface. The temperature of the chill surface in contact with the solution remains constant during solidification. Experimentally, it is observed that deudrite sparing increases linearly with distance from the chill surface; in the light of heat -flow analysis this means that the dendrile spacing is imersely proportional to the square root of the maximum freezing rate. SOLIDIFICATION of liquids is accompanied by rejection of latent heat at the solid-liquid interface. The over-all rate of liquid to solid transformation is governed by the rate of heat extraction. Analysis of the heat transfer in the liquid during freezing is important since it determines the freezing rate and resulting structure. A considerable amount of work has been done on metallic systems since solidification is frequently a major step in processing metals. Unidirectional freezing from heat sinks has been treated by several investigators.1-4 Much of the work has been limited to the simpler case of substances such as pure metals which freeze isothermally at a unique transformation temperature. In this case the thickness of the solid zone y, next to a chill surface. is a parabolic function of the time. 8. where a and b are constants. Eq. |1| is a close approximation giving the progress of solidification for the case in which there is a small but finite thermal contact resistance at the interface between the freezing liquid and the chill.' It has been used with some success in connection with large steel ingots4 when the therma1 contact resistance is negligibly small (as is the case when water is brought into contact with the metal chill). The constant, b. becomes zero and Eq. [l] is then exact. even when the thermal properties of the chill and the freezing liquid depend on temperature. Analysis of unidirectional solidification of solutions is more complicated since the latent heat is evolved over a range of temperatures. Next to the all-solid zone in contact with the chill surface there is a solid plus liquid zone in which solidification takes place. Although the equations presented are considered quite general the numerical and experimental results are for freezing of aqueous solutions from a copper chill. I) EXPERIMENTAL PROCEDURE Solutions of potassium chloride, sodium chloride. and lithium chloride have been used. These solutions form a eutectic: a typical phase diagram is shown in Fig. 1. A solution at its liquid us temperature is poured into a tygon tube mounted on a relatively large copper chill. The chill is immersed in a freezing mixture of dry ice and acetone at -70°C. A thermocouple connected to a high-speed recorder was mounted near the top of the chill to measure the fluctuation in the temperature of chill surface in contact with the solution. In this system the progress of solidification can be visually observed through the tygon tube. After the specimens freeze to a desired height they are removed from the copper chill and stripped from the tygon tube. Longitudinal and transverse sections are cut from the specimen for micrographic examination. Specimens in the form of a thin slice are mounted on a transparent glass slide by freezing small drops of water around the periphery. They are then polished on a series of emery papers; the final finishing is done on a soft tissue paper. A Leitz Biological microscope was used for structural observations; photography was

Jan 1, 1968

The Committee on Technical Nomenclature, of which John T. Faig, Professor of Mechanical Engineering at the University of Cincinnati, is Chairman, appointed by the Society for the Promotion of Engineering Education, has recently issued a report advocating uniformity in the use of symbols to designate engineering and mathematical terms: The selection of the symbols was based upon a canvas of a considerable number of engineers, editors of engineering papers, and professors of engineering throughout the United States. The list, as finally accepted by the Committee and recommended for universal adoption, is as follows: Concept Symbol I Concept Symbol Acceleration due to gravity 'g Length L Acceleration, linear a Mass m Area A Modulus of section Z Breadth b Modulus of elasticity, Young's... E Center of rotation 0 Moment of force M Coefficients and constants C, K Moment of inertia, polar J Deflection of beam y Moment of inertia, rectangular.. I Depth : d Quantity of liquid flowing Q Diameter D . Radius r Distance passed over s Radius of gyration k Distance of extreme fiber from Reactions R neutral aids C Revolutions per unit of time.... N Eccentricity of application of load e Stress, unit S Efficiency (hydr., mech., vol.)...er,.em, e9 Time t Force F Torque T Friction, coefficient of f Velocity, angular :. W Head H 'Velocity, linear V Height h Volume V Horsepower : Hp Weight W Hydraulic radius Re Previous lists of symbols have not secured wide acceptance in, this country; some that have been proposed by prominent writers are familiar to very few engineers. The above list is presented in the hope that it will assist in the evolution of a standard list. It is short; it contains no Greek letters; it is mnemonic to a considerable degree, though not by

Jan 1, 1918

By G. L. F. Powell, L. M. Hogan

Large degrees of undercooling have been produced in bulk samples, 400 g, of copper and Cu-O alloys by melting in a slag of commercial soda-lime glass. The maximum degrees of undercooling obtained for copper, hypoeutectic and hypereutectic Cu-O alloy samples were 208°, 218°, and 97°C, respectively. No grain refinement as a function of undercooling was observed for the pure copper samples although in Cu-O alloys there was a marked decrease in grain size at degrees of undercooling greater than 150°C. The grain size change is the result of recrystallization during or immediately following the freezing process. THE first report of a large degree of undercooling in a bulk sample of metal was that by Bardenheuer and Bleckmann1 who produced 258°C undercooling in a 150-g sample of iron by melting in a glass slag. Garbeck2 extended this technique to nickel, cobalt, and copper and reported maximum undercoolings of 220°, 230°, and 60°C, respectively, while Fehling and schei13 undercooled a large number of metals as 2 to 20-g samples slagged in glass. Subsequently, one of the authors4 applied the glass slag technique to bulk samples, -500 g, of silver and obtained a maximum undercooling of 250°C. It was concluded that impurities which normally catalyze nucleation at small degrees of undercooling could be removed by oxidation and solution in a glass slag. Large undercooling of bulk samples of iron, nickel, cobalt, and their alloys has also been reported by other authors.8'10'11 Of the five metals mentioned above, copper was the only one which had not been undercooled by at least 200°C in the form of a large bulk sample. Since copper exhibits high liquid solubility for oxygen, as do iron, nickel, cobalt, and silver, it was considered that a much larger degree of undercooling than that observed by Garbeck for copper should be possible. This was obtained by modification of the technique applied previously to silver and the results of undercooling experiments with 400-g samples of copper form part of this paper. The undercooling behavior of Cu-O alloys was also studied, and the influence of a small oxygen content on the grain structure of undercooled copper was observed metallographically. 1) EXPERIMENTAL The copper was obtained as oxygen-free high-conductivity copper, the major impurities of which were Fe 0.01 pct, Zn 0.015 pct, and Si 0.02 pct. Melting was carried out in an open-ended vertical cylindrical fur- nace wound with Kanthal wire. A schematic diagram of the experimental setup is shown in Fig. 1. The undercooling technique previously used for silver4 involved preoxidation of the samples by melting the silver in contact with the atmosphere. The oxygen content was subsequently reduced by freezing the samples under a glass slag, whereby the oxygen was evolved as gas and the continuous glass cover over the surface prevented re-solution of oxygen when the sample was remelted. Since oxygen is not released as gas when a Cu-O alloy is frozen. the technique had to be modified for use with copper. Also, copper is oxidized during fire refining so that an in situ preoxidation treatment of the samples was not considered to be a prerequisite to large undercooling. Experimentation proved that this supposition was correct. Instead, it was found that care was necessary during melting of the copper under glass to minimize oxygen pickup. Samples of copper weighing 400 g were prepared by adding 50-g pieces of copper to a vitreous silica crucible partly filled with soda lime glass at a temperature of approximately 1000°C. Each piece was quickly immersed in the glass slag and held at this temperature until the oxide coating on the surface decomposed. This change was easily observed and coincided with the formation of gas bubbles in the glass

Jan 1, 1969

By T. S. Liu, E. A. Peretti

A LITERATURE survey of the In-Sb system, which was made before a study of the binary diagram was undertaken, revealed that the intermediate phase InSb existed and that its crystal structure is face-centered cubic of the zinc blend type. In 1929 Goldschmidt' determined the lattice constant for InSb and obtained a value of 6.452A. A more recent value, 6.461A was reported by Iandelli2 in 1941. The purity of the indium used was not very high, however. The indium used by Iandelli contained 2 pct Ge. In view of this fact it was decided to remeasure the lattice parameter using high-purity indium (99.97+ pct In) and spectrographically standardized antimony of the highest purity available (99.91 pct Sb). Specimens corresponding to the InSb composition were made by carefully weighing the ingredients on an analytical balance and heating them in vacuo in a quartz tube at 700°C. As melting losses were negligible, the alloys were not analyzed chemically, but the intended analysis was taken as being accu- rate. Powder samples were prepared by either filing or crushing of the brittle alloy, followed by screening at 325 mesh. The powders were then annealed at 400°C in evacuated capsules for about an hour. X-ray photograms were taken with a Debye and a back-reflection focusing camera, using characteristic cobalt K. radiation. Lattice parameters were calculated by Cohen's³ method. The results of a Debye pattern and of a back-reflection pattern at 25°C are given in Tables I and 11. The lattice parameter at 25 °C is 6.47602A.

Jan 1, 1952

By James R. Cudworth

OUR colleges and universities have met many difficulties during the past year. From a period of small enrollments and depleted faculties, the educational institutions have passed quickly to a period of the largest enrollments in their history with inadequate facilities and staffs. The results of the shortsighted policy of the Selective Service system which drained the technical schools and universities of many of the students who were potential teachers are now being felt. The movement of faculty members into positions in industry during the war years has resulted in many of them forsaking permanently the educational field for the higher salaried positions they now occupy. Competition is keen between the educational institutions, and between the institutions and industry, for technically trained men. Dean Holbrook's statement in last year's annual review that he thought it would take three or four years to restore our engineering departments to their former level in quality of instructors is even more convincing today. Somehow, the institutions must not only reach their former level in quality of instruction but they must also increase the quantity of their staffs to meet the demands of the ex-service men and the high school graduates for engineering education. The enrollments in the mineral industry fields of mining, metallurgical, geological, petroleum, and ceramic engineering, although greatly increased, are not expanding as much as in the more widely known fields of electrical, mechanical, aeronautical, and civil engineering. In fact, many educators are tremendously worried about the segregation of so many young men in a relatively few fields while the needs of others will remain unanswered.

Jan 1, 1947

By M. S. Miller, R. H. Mullennex

The growing need for development of thinner, more erratic, or less easily-mined coals in the Appalachian region requires more detailed analysis of conditions and factors controlling or influencing deposition of these seams. The value of depositional modeling in evaluation of such coals has been demonstrated in many recent studies and publications. Such modeling may be applied to allow prediction of factors varying from regional coal occurrence trends to very local areas of seam discontinuities but requires thorough we of all available types of data. Mapping of general depositional energies, as derived from basic geophysical and driller's logs, can be applied to specific prediction of coal occurrence, and projection of particular facies as representative of unique depositional features or conditions may prove more applicable to coal character delineation than mapping of the coal itself. Depositional modeling and trend projection may also serve as a guideline in reserve classification and confidence levels in reserve estimations.

Jan 1, 1983

By C. H. Wilson, J. W. Daly, J. J. Jakosky

Meteor Crater, Arizona, is a natural wonder which for years has been the subject of considerable discussion and study as to its origin and age (Fig. 1). Of the various theories advanced regarding the origin, two have been considered as most probable by a majority of investigators. The first theory is that the crater was formed by a meteorite or a swarm of meteoric material striking the earth at a high velocity and burying itself. The second theory is that the crater was formed by a "steam explosion" from hot solutions or gases coming from underneath the present sedimentary beds which overlie the area. In order to obtain more detailed information regarding the conditions existing at the crater, the present management decided to have a detailed geophysical examination made. The origin of the crater is of considerable scientific importance and interest. More or less active mining operations have been carried out during the past 20 years by various groups who believed that the crater was of meteoric origin, and who hoped that sufficient quantities of such material had been buried to be commercially valuable. Fragments of meteoric material found on the surface of the ground in the debris around the rim gave analysis of approximately 92 per cent iron and 8 per cent nickel, with some platinum and iridium. The material having a gross value of approximately $50 per ton, mining would be commercially profitable if sufficient quantities of the material existed in condition for mining. In the early work numerous drill holes and shallow shafts were put down, mainly in the northern portion of the crater. Pulverized material and debris caused considerable difficulty, and in an effort to overcome this the present management started a 1500-ft., two-compartment shaft on the south rim of the crater and outside of the fill zone. The intention was to sink the shaft in the solid rock outside of the crater, and then to crosscut toward the crater at a depth of 1500 ft. The work was finally stopped when a depth of 650 ft. was reached, because water poured into the shaft through large cracks and fissures in the rock. The enormous force responsible for the crater had also broken

Jan 1, 1932

By P. B. Liebermann

THE resistance to motion offered by mine cars is caused principally by: Rolling friction, flange friction, bending rails, bearing friction and wind resistance. With proper construction and with a fair amount of attention and care, that is, under favorable conditions, the first three items cannot be greatly improved. The wind resistance ordinarily is negligible on account of the slow speeds commonly used. The bearing friction, however, is a variable item, depending upon the design, the bearing material, the lubrication, the location (whether in wheel-hub or on car-body) and the alignment. Under the most favorable conditions the bearing friction will reach a lowest possible value. By the development of a successful anti-friction mine-car bearing this lowest value has been improved to such an extent as to affect the whole system of mine haulage. After being satisfied of their durability and certainty of operation, any investigation into the advantages of anti-friction bearings for mine cars will have to be based upon reliable information as to the saving in power of such bearings. While numerous tests have been made in this direction, the results have not always been convincing, principally because of the rather crude methods that were employed. These crude methods are the main cause of the wide variations existing in regard to the exact amount of the frictional resistance. Frequently an ordinary spring balance is used and the pull necessary to move a certain car or train of cars is obtained by a number of readings. Such spring balances necessarily have a coarse graduation and the continuous vibration and fluctuations to which they are subjected make them highly dependent upon the individual observer. Further, they must be frequently calibrated. Sometimes these tests were made without regard to acceleration, speed or even grade.

Jan 6, 1916

By C. E. Nelson

The purpose of this discussion is to outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as far as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, the principal aim of this paper will be to deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. Types oF Melting Practice All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux.2 The flux provides protection during melting and a molten pool of flux into which the solid magnesium melts. It is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies; then on quiet standing separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be ' parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is usually desirable. The open-pot method is used generally in the following processes: (I) alloying and secondary smelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings requiring hand ladling, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drying out or thickening after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to be poured out directly into castings without fear of flux contamination. This flux is not

Jan 1, 1944

By Leland H. Johnson

THE Tennessee Coal, Iron & Railroad Co.'s ore mines began experimental tests with trackless mining units early in 1947. The units had many weaknesses to overcome, but are now well beyond the experimental stage and are becoming a necessity to ore seams that are amenable to this type of equipment. The development of this type of mining with the problems of increased underground supervision, maintenance, and training personnel, along with the benefits derived, are discussed.

Jan 12, 1950

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By P. D. Bush, E. H. Gates, M. D. Vijayaraghavan, L. F. Engle

The process developed over the last few years by Republic Steel Corporation in conjunction with Colorado School of Mines Research Institute has been used as a basis for the conceptual engineering of full size plants. The paper will cover the equipment design criteria, equipment design itself, and the integration of the complex unit operations. There are unique features of agitation and use of gas media through- out. The paper will provide an illustrative example of the process requirements for a variety of raw material feeds. It will discuss the materials of construction approach required.

Jan 1, 1973

By K. Hanumantha Rao, A. Nayak, . K. S. Narasimhan, S. N. Mahapatra

Selective flocculation studies carried out with iron ore tailings generated at Kudremukh iron ore plant indicate that a concentrate containing 63% iron can be obtained from the tailings containing 34% iron with around 60% recovery. This opens up the possibility of recovering most of the iron lost in the tailings generated at 2 kt/h (2200 stph) while processing 22 Mt (24 million st) ore per year. This would mean that the productivity could increase by around 50%. In these studies, it has been established that caustic degraded tapioca starch is a most effective agent for selective flocculation. While potato starch after caustic degradation can also be used, neither the parent starch nor the amylopectin compound is as effective.

Jan 1, 1986

THE CHAIRMAN (G. H. CLEVENGER, Stanford University, Cal.).¬I would like to ask Mr. Pyne if he has had any experience inn the use of chromite as refractory under conditions that are highly reducing? I am reminded of an experience I once had with an electric furnace. I imagined that chromite would form a splendid lining, but it soon disappeared; hence it seems probable that, under highly reducing conditions at a high temperature, chromite is a very poor refractory. F. R. PYNE.-In copper smelting the atmosphere is generally neutral, or slightly oxidizing; we do not use highly reducing atmospheres at all, not even in the matting furnace. You can take the chromite brick and treat it as you would an iron ore, obtaining ferro-chrome very readily, from which the copper will separate. We have done this; in fact, at one time we considered installing a small electric furnace for the production of ferro-chrome. FOREST RUTHERFORD, New York, N. Y.-During the time I was general superintendent at the smelter of the Copper Queen Consolidated Mining Co., at Douglas, Ariz., a great many experiments were made on the furnaces and settlers with different kinds of brick, and I agree with Mr. Pyne's statements about chrome brick. Their power to absorb metals is very great, and as they cannot be smelted at any temperatures obtainable in a copper furnace, to get rid of the bats and extract the metal from them is quite a problem. We finally got down to using chrome brick only for lining the settlers, out of which we often got a life of upwards of 2 years, and for lining the blast-furnace bottoms, for the reason that chrome brick can be heated and wet, or wet after being heated, without going to pieces, whereas under these conditions magnesite brick will break down very rapidly. We also used a layer of chrome brick above and below an 18-in. band of magnesite brick put on the slag line of the reverberatories, in order to separate the magnesite from the silica brick, fearing that they would slag each other and let the wall drop. The idea worked, but became unnecessary on account of a change made in the method of feeding the furnaces. Chronic brick will not stand up under pressure so well as a good Grecian or Austrian magnesite brick, on account of the poorer bonding properties of the materials from which the chrome brick is made.

Jan 4, 1918

By William Hilliard

IN any manufacturing business, it is of vital importance that the management should know the exact cost of the units of production. Without such knowledge, a company can sell blindly in the open market, obtaining the best prices it can in competition with other firms, and manage perhaps to continue in business for a time; but at any moment, and especially in a period of falling prices, such a firm is at a loss to know exactly at what point it can sell at a profit and exactly how much it is losing per unit if it sells below that point. Furthermore, it is necessary not simply to know the exact total cost per unit, but to know definitely all the different-factors which enter into that cost. A firm manufacturing pocket knives had been doing a profitable business for many years when it began to earn smaller and smaller profits, until there was scarcely any profit at all being realized. Being unable to determine exactly what its future policy should be, it called in experts who studied the past records carefully and followed out for a period a better cost, system. Investigation then showed that on several different kinds of knives in common use, a small profit per unit was being made. On a number of special kinds of knives, of which the firm was very proud, it had been forced to cut prices under the pressure of outside competition and had believed that a small profit per unit was still being made on that product, while a detailed cost analysis showed that a loss was being incurred on each knife of that kind produced. It then became clear that the company must either give up the special line and concentrate wholly on the cheaper knives and extend their sales to territory not yet developed; or expand its plant and produce more of the higher grade knives and thus lower the cost per unit enough to make money on the higher grade knives also, if conditions warranted such expansion. Investigation revealed that the market for large quantities of the high-grade -knives was decidedly uncertain and that the most promising move would be to manufacture only the less expensive knives on a larger scale. That plan was carried out and the concern began again to make a better profit.

Jan 1, 1932