Search Documents

[Abrahamson, Guy C., (5'43) Lt., 0-880861, Hammer Field Fresno Calif. Adamec, LAW, (8'42) c/o Braden Copper Co., Rancagua, Chile. Adams, Karl S., (9'43) Univ. of New Hampshire, Durham, N. H. Agnilar, Roperto Q., (9'43) Texas College of Mines, El Paso Texas. Ainge, B'onald Farra, (943) Otago University, Dunedin, New Zealand. Akaran, Cevdet A,, (9'44) Pennsylvania State College, State College, Pa. Albala, Americo, (5'44) School of Mineral Industries, The Pennsylvania State College, State College, PA.]

Jan 1, 1946

By J. W. Evans

ONE possible method for the separation of hafnium from zirconium is by the vapor phase oxidation of the purified mixed chlorides. An important factor for success depends on the difference in free energies of the following reactions: ZrCl(g) + O2 = ZrO2(s) + 2C12 [1] HfCl4(g) + O2 = HfO2(s) + 2C12. [2] Prakash and Sundaram1 have calculated these values from certain data and carried out experimental work with partial success. However, their free energy values for reaction 2 diverge rather widely from other data which are presented here. The possibility of successful separation is briefly considered in the light of these alternative values. Table I shows the free energy values (?F°) for reactions 1 and 2 derived from the recent compilation of data on oxides and chlorides by Glassner.2 The corresponding values of Prakash and Sundaram for the same temperatures are also shown. The alternative values to those of Prakash and Sundaram for reaction 2 are substantially confirmed by the data of Kubaschewski and Evans" and Cough-lin' on heats of formation, entropies, and heats of vaporization. In spite of the considerable uncertainty in the hafnium data it is reasonable to suppose that the oxide-chloride free energy difference for two such chemically similar elements would not be very far apart. These figures indicate clearly that the oxidation of hafnium chloride is appreciable at all temperatures. Nevertheless, there is a significant difference between the values for reactions 1 and 2

Jan 1, 1959

By Axel Hultgren

In ingots of silicon-killed carbon steel-made without addition of aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents and, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,l0,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis1' and their amount to increase from the top downward in the axial region.2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form,'' by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.'= Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19.20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping1 or of refractory material from various sourcesl,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistamce to hydrofluoric acid, imparted by the alumina content. Silicate inclusions are often referred to as the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1949

By Axel Hultgren

In ingots of silicon-killed carbon steel-made without addition of aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents and, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,l0,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis1' and their amount to increase from the top downward in the axial region.2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form,'' by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.'= Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19.20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping1 or of refractory material from various sourcesl,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistamce to hydrofluoric acid, imparted by the alumina content. Silicate inclusions are often referred to as the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1949

By Henry Hibbard

Fox the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seen to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machinery, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume.

Jan 9, 1919

By W. T. Allan

RAW bituminous coal has been in general use as a blast-furnace fuel in Scotland for the last century, and although its use has now been largely abandoned and it has been replaced by coke in the majority of the few furnaces which are at, present in blast in this country, coal-smelted pig iron is not yet a thing of the past; it is still being produced and mar-keted in competition with the more cheaply smelted product of the coke-fired furnace. Various factors have influenced this change in practice; the once plentiful deposits of coal of a suitable nature for the blast furnace are now not so easily obtainable; native blackband and clayband ironstones which are easily smelted in the coal-fired blast furnace, although still far from being exhausted, are not available except at a. cost that is somewhat higher than that of imported ores, making them unattractive to the ironmaster that is compelled by circumstances to smelt his iron at the lowest possible cost. Within the last 15 years overproduction of synthetic nitrogen has led to progressive reductions in the price of sulphate of ammonia, the recovery of which together with the other by-products before that time materially assisted in reducing the working costs of the coal-fired furnace. Now the sale of the by-products recovered yields a diminished profit. When the cost of the product is the only consideration the small, slow-smelting, coal-fired blast furnace cannot compare with its large, modern, coke-fired competitor. Other `considerations do not by any means all support the same side of the argument. In the smelting of pig iron to be used in the manufacture of steel where the quality of the final product depends so largely upon the control of the conversion process and so much less upon the physical quality of the pig iron used, the physical properties of the pig iron do not exert any appreciable influence upon the quality of the steel produced, therefore the methods employed in the smelting of the pig iron matter but little so long as the requisite chemical composi-tion is reached. On the other hand, in ironfounding where the simple melting of the pig iron, which is the only treatment it receives before being cast into its final form, does little or nothing to modify its original charac-

Jan 1, 1937

By Earl S. Greiner, Eric R. Jette

The literalure on the binary alloys of iron and silicon has been reviewed by Stoughton and Greiner.1 Another even more extensive and detailed survey of the present knowledge has been prepared under the auspices of the Alloys of Iron Research Committee by Greiner, Marsh and Stoughton. Since the latter surrey has already been issued in its preliminary form, it will be unnecessary to review the literature in the present article. However, in this connection there should be noted the important work on the crystal structures of the iron-silicon alloys by Phragmén,2 who investigated the entire system, identified the various phases and determined the homogeneity ranges of these phases. It was evident in the surveys cited above that in the range from 0 to 15 per cent silicon, which includes the commercially most important, alloys, the results obtained by thermal analysis, microscopic examination and the determination of electrical, magnetic and mechanical properties were extremely confusing. From time to time various compounds between iron and silicon have been postulated to account for the results yielded by the classical methods, and much argument has ensued. It was presumed that if compounds occurred which are sufficiently diverse in their properties to account for the characteristics of the alloys, they should be recognizable as separate phases but satisfactory proof of this sort has not been found by thermal or microscopic methods. Contributing to the confusion is the fact that the electrical, the magnetic and some of the mechanical properties are "structure sensit'ive"; i. e., they are influenced to a marked degree by the presence of minute amounts of impurities, the specific characters of these impurities, the grain size, the character of the grain boundaries, small general or local strains, etc. Thus interpretations of the discontinuities in the various property versus composition curves that identified these discontinuities with phase changes or compound formation have always been open to question.

Jan 1, 1933

By R. V. Ramani, G. W. Luxbacher

Computer simulation of mine ventilation system is rapidly becoming an essential tool in mine planning and design. This Paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve primarily for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1980

By J. J. Casey, R. S. Busk, D. L. Leman

The mechanical properties and the phase-temperature relationships of magnesium-lithium-aluminum, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys are presented. It is shown that the strengths of some of these alloys can be tripled by heat treating and aging but that the high strength is accompanied by brittleness and lack of stability. MAGNESIUM-LITHIUM alloys are interesting because the hexagonal structure of magnesium can be changed into the more ductile and workable body-centered cubic structure by the addition of only 10 pct lithium.1 After Loonam2 determined that the ductility of the magnesium-lithium alloys is destroyed by even trace quantities of sodium, it was possible to prepare ductile alioys and study their mechanical properties. Jackson3 and coworkers have ably described their results with both the binary and polynary magnesium-lithium alloys. The present paper is a report of the mechanical properties of wrought magnesium-lithium-aluminurn, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys. Experimental Procedure The alloys were made by melting 7 lb of magnesium in a steel crucible under a molten flux of 75 pct LiCl + 25 pct LiF3 previously dried at 1600°F. The metal was heated to 1300°F for alloying aluminum and zinc and then cooled to 1250°F for adding lithium (sodium content: 0.01 to 0.04 pct). After the lithium had been alloyed, dry LiF powder was sprinkled on the melt to thicken the excess flux. After a 15 min holding period, the flux was skimmed off. Paraffin vapors were used to protect the metal as it was poured into 3 in. diam by 11 in. long magnesium molds. Billets were extruded into 3/8-in. diam rod and 1/16 x 3/4-in. strip; sheet was prepared from 1/8x 7/8-in. extruded strip, first by hot rolling and then by cold rolling 2 pct per pass. Hot rollability, or the temperature range through which the alloys could be rolled, was determined by rolling the strip two passes at 30 pct reduction per pass. Cold rollability, or the percentage of cold reduction to cause detrimental cracking, was determined on 0.064-in. hot-rolled sheet. Standard ASTM procedures were followed to obtain the mechanical properties, using 0.2 pct offset for the yield strengths. The level of properties produced with commercial magnesium alloys using the procedure described is given in a previous publication." Results Magnesium - Lithium - Aluminum System: The good workability of magnesium-lithium alloys is illustrated by the data in table I, which shows approximately how the extrusion pressure decreases as the amount of cubic phase increases. Binary magnesium-lithium alloys are soft and weak, but aluminum raises their strengths con-

Jan 1, 1951

By Charles M. Stone, Dale S. Preece

Introduction The Strategic Petroleum Reserves (SPR) is a national program dedicated to storage of large quantities of crude oil in leached salt caverns in the Texas-Louisiana gulf coast area. The program has required storage in existing caverns at each site and includes plans to leach new ones. The structural stability of each cavern depends on the behavior of the surrounding salt. In the past cavern stability has been predicted based on experience with other caverns in the vicinity. With the development of good non-linear finite element structural computer programs, it is possible to predict stability before the cavern is created. An important step in verifying the applicability of these predictive methods is comparison of analytical and field data. The analytical data come from finite element analyses of a specific cavern where the laboratory determined material properties and an approximation to the cavern geometry are used as input. These comparisons have been made for caverns in the Bayou Choctaw Dome (Louisiana) and Eminence Dome (Mississippi) with reasonably good correlation being obtained between measured and predicted volumetric response of the caverns. This paper discusses 1) the acquisition of material properties, 2) the finite element program SANCHO, and 3) the comparison of analytical and field data for each of the caverns.

Jan 1, 1982

By Charles E. Weaver

Discussion of the paper of CHARLES E. WEAVER, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 103, July, 1915, pp. 1419 to 1427. MILNOR ROBERT, Seattle, Wash.-A year ago at this time, 12 wells were being drilled for oil in western Washington. Some excitement attended the operations; many thousand acres of land were leased to oil companies and stock was widely advertised. The location of the wells may be described by referring to the conclusions in Dr. Weaver's paper, in which the State is divided into four areas. In the area described first, which includes the Cascade Mountains and eastern Washington, where conditions are decidedly against the existence of commercial oil fields, no new drilling was reported. In the second area, the Puget Sound Basin, where conditions are unfavorable, but to a less degree, five wells were being drilled. The third region, covering certain parts of southwestern Washington, contained four drilling wells and several others projected or beginning operations, in spite of the absence of petroleum seepages. None of the wells mentioned is fully active today. On the western side of the Olympic Peninsula, along the Pacific Ocean, are three wells which have been the scene of operations for the past two to three years. The region they are prospecting contains seepages of light oils and is the fourth area described in the paper. The difficulties of transporting both men and supplies to the well sites have delayed operations and brought the costs up to high figures. The drilling of these three wells is interesting on account of the presence of oil in nearby seepages and its occasional appearances in the material penetrated. A. C. McLAUGHLIN, San Francisco, Cal.-The most important part of Washington is on the Olympic Peninsula. The geological conditions on the Peninsula are not similar to the conditions in California, and it would not prove to be a continuous belt of oil-bearing territory from there to here if oil should be found at either end.

Jan 12, 1915

By H. H. Waller, D. L. Monroe, D. P. R. Smyth

ORIGINALLY slusher drift development was conventional, advancing the drift full 10x13-ft size at 6 ft per round. This proved dangerous and costly because the weak fractured rock of the orebody cannot be left raw for any length of time without its reacting with air to cause spalling. With this method of drift development ground conditions were worsened by many blasts and the length of time it was necessary for the drift to remain open. The problem was practically solved by driving 5x7-ft pilot drifts, then enlarging to 10x13-ft raw size by slashing with 50 to 60-ft diamond drill holes. Calculated explosive charges are used to avoid wall and roof shattering. Still more recently jacklegs and sectional steel replaced the diamond drills, resulting in the same work for less than half the cost, see Figs. 1 and 2. Crosscuts at right angles to the main haulage drifts, which cross through the center of the ore-body, divide the ore into 200-ft blocks. Eight slusher drifts on 50-ft centers draw from one block. The slusher floor is 11 ft above the rail, inclined at 1 pct grade, and the top is 18 ft below the undercut. The finished slusher drift is 102.5 or 120 ft long, depending on whether it is north or south of the crosscut. Drawpoints are staggered on each side at 17.5-ft centers. The completed drift is concreted and has an inclined ramp and a vent at the back. When crosscuts and gangways have been excavated and concreted and slusher stations installed, slusher drift development is carried out in 10 clear-cut stages: 1—Pilot drift is driven full length, 5x7 ft. 2—Station is excavated at half-way point in pilot drift. 3—Pilot drift is enlarged to slusher drift size by drilling. 4—Lower part of slash is blasted and mucked for floor concrete. 5—Floor is poured. 6—Inside upper half of slusher drift is blasted, mucked, and concreted. 7—Outside upper half of slusher drift is blasted, mucked, and concreted. 8—Drawpoints are excavated. 9—Drawpoints are concreted. 10—Concrete ramp and sheave protection recess are constructed at back end of slusher drift. A 5x7-ft pilot drift is driven full length on the center line of the proposed slusher drift using a jackleg and detachable bits on 7/8-in. hexagon steel. A 10-hp air-driven slusher and 36-in. scraper pull muck directly into cars in the main haulage crosscut, see Fig. 2. Operations are on a three-shift basis. One man mucks the previous round, drills, and blasts his round in a shift. Average advance is 5 ft per shift. When the pilot drift is completed, 7 ft of drift in the center section is enlarged to full raw slusher drift size of 10x13 ft, for the set-up to drill long slash holes. The pilot drift is slashed to full raw size from this station with jacklegs and tungsten carbide chisel bits on 7/8-in. sectional steel. Crews line the holes without trouble, working from controls established by the engineers, and the pattern of holes for the slash is arranged to give the least shattering effect

Jan 1, 1955

By D. L. King, B. A. Schepman

A number of unique thickener mechanism designs with the operating results achieved in various installations are discussed. These unusual designs include new types of raking arms, lifting devices, and feed-wells employed to obtain higher underflow densities and minimum operator control or improved overflow clarity. Several installations of large thickeners in which the underflow lines pass upward through the center to eliminate tunnels are reviewed. The location of the lines and pumps with the maintenance and operating records are included. Several types of automatic lifting device controls are used to provide storage in the thickener. Some of the installations employing underflow density controls are achieving excellent operating results. Thickeners or sedimentation basins are used in minerals beneficiation plants for three basic purposes. These are 1) Concentration, or to raise the density of a liquid-solids slurry. 2) Clarification, or removal of finely divided solids from a slurry. 3) Hydroseparation, or removal of a specific fraction of solids from a slurry. The concepts that control the size and configuration of basins used for these purposes are different. Likewise, different equipment is properly employed to accomplish these various objectives. The pattern of liquid and solids flow in the clarification zone of a sedimentation basin used for thickening or raising the density of a pulp normally is not critical. That is, the solids normally will drop or plunge to the bottom quite readily, and the liquid separates itself from these solids so as to overflow the basin in a relatively clear condition. When clarification or removal of finely divided particles is to be accomplished, the flow patterns in the basin are extremely important. The velocity of the incoming stream must be dissipated and the liquid flow distributed ]In the tank so that the feed is not divided into streams that flow directly to the overflow carrying the fine:ly divided solids that are to be removed. Similarly, the configuration of the arms that provide the raking and thickening of the pulp is not as important in basins primarily devoted to clarification. In thickening, the design of the arms and the manner in which the pulp is moved or worked, can contribute appreciably to the thickening process and achievement of a higher density underflow. THICKENING As the grade oi ore bodies throughout the world generally decreases, and chemical processes, hydro-metallurgy, and other more refined methods of minerals beneficiation are required, problems in thickening become more acute. Difficult operating conditions, previously encountered only occasionally in thickening metallurgical slurries, or clarifying process streams in the mill, are now the rule rather than the exception. Fig. 1 illustrates some of the different types of raking arms that are successfully achieving the desired goals in pulp thickening. The conventional raking arms consist of a relatively simple truss with the blades attached to the bottom chords. This design provides proper Concentration of many 'normal' slurries. A modificaiion of this design as shown in the center is being used with excellent results on large thickener basins where it is desirable to have a

Jan 1, 1962

By Paul Merica

ALTHOUGH nickel was discovered and isolated as early as 1750 and its valuable properties recognized, many years passed before it was used commercially for wire, sheet, rods, etc., in the pure form. This was due partly to its high cost at that time and partly to the fact that it was not possible to refine and cast nickel into ingots sufficiently malleable to be amenable to the usual forging, rolling, or drawing processes. So remarkable was this fact, and so different from the experience at that time with metals such as copper and iron, that it has left its impress on the no-menclature within the nickel industry. To this day, furnace-cast nickel produced in such a manner as to be suitable for rolling and forging is called malleable nickel to distinguish it from the ordinary pig and shot nickel of commerce. In 1878, the firm of Jos. Wharton, of Philadelphia (which later became The American Nickel Works, a constituent of The International Nickel Co.) exhibited at the Paris Exhibition specimens of rolled pure nickel strip and of drawn nickel wire. About this time, there was considerable activity in the study of the refining of nickel and several methods were described, some of which were patented, for the production of furnace-cast malleable nickel including the use of manganese (Boed-dicker,1 Selve and Lotter2), the use of potassium permanganate (Bernsdorfer Metallwarenfabrik3) and the use of phosphorus (Garnier4). By far the most efficient method was discovered by Th. Fleitmann in 1879;5 it consisted in adding to the molten nickel, just before pouring the castings, from 0.05 to 0.125 per cent. of metallic magnesium. This soon became the recognized final malleableizing treatment for furnace-cast nickel.

Jan 1, 1925

By M. Cohen, R. J. Teitel

There is considerable interest in beryllium because of its low density (1.84 g per cu cm), high modulus of elasticity (40 X 106 psi), high melting point (1280°C), and special nuclear characteristics. Moreover, it has fair resistance to corrosion and oxidation. However, the purest beryllium known to the authors is relatively brittle at room temperature, and cannot be fabricated readily. The search for improved properties leads naturally to investigations of beryllium alloys and the phase relationships upon which they are based. The present paper is concerned with the alloys of beryllium and iron, primarily from the standpoint of the equilibrium diagram. Iron was selected (1) because of its all-round importance in metallurgy, and (2) because the beryllium-iron system is known to be quite complex. The most recent diagram in the literature is that of Gaev and Sokolov,' and covers only the iron-rich end up to 16 wt pct beryllium. Beryllium markedly restricts the austenitic field, closing the gamma loop at about 0.4 wt pct (3 at. pct). On the other hand, beryllium is soluble in a-ferrite up to a maximum of 7.5 wt pct (34 at. pct) at the eutectic temperature of 1160"C. The eutectic composition lies at 10 wt pct beryllium (42 at. pct) and corresponds to a mixture of or and FeBez (called j3 in the present paper). The solid solubility of beryllium in the a phase decreases with decreasing temperature, and makes precipitation-hardening possible. These findings substantiate the earlier work of Oester-held,2 Wever and Mueller3 and Laissus.4 In addition to the FeBe2 (ß) mentioned above, Misch6 has reported on FeBes, and indicated evidence for another compound containing still more beryllium. A preliminary diagram by Gordon,5 not hitherto published, is given in Fig 1. Besides the phases previously named, there are shown a solid solution of extended range (e), a compound of limited solubility (t), and a high temperature phase (7). Beryllium is designated as 8. The t field contains the compound composition FeBea, and the f phase undoubtedly corresponds to the beryllium-rich compound found by Misch.6 The region around the { phase was proposed by R. J. Teitel based on Gordon's data. The details of the diagram are self-explanatory. It was the unusual complexity of this system that prompted the authors to undertake the present studies. By the same token, more emphasis was placed on the beryllium-rich than the iron-rich end of the diagram. Exprimental Details RAW MATERIALS The beryllium employed in this investigation was one of the purest grades available. Its chemical analysis after vacuum melting is given in Table 1. The metal assayed 99.4 wt pct beryllium. Vacuum melted electrolytic iron of purity shown in Table 1 was the source of iron.

Jan 1, 1950

By J. Richard Maier

Short-range mine planning (less than five years) previously was accomplished using contour and isopac maps, pencil and paper, an abacus, and our lucky quarter. Through the use of both micros and mainframe time sharing, Glenrock Coal Company (GCC) has been able to virtually put the old equipment away (except the problem solving quarter). In the process, GCC has saved many man-days and eliminated the more tedious parts of mine planning, such as picking elevations off a map with an engineer's scale and repetitive calculations. These savings have allowed GCC to do a more extensive job of mine planning as well as offer more alternatives, making GCC better prepared for possible economic changes. Mine planning, simply, involves looking at what has been done and deciding what needs to be done using various constraints. The application of this concept is not as easy as it sounds. The need for experience and insight cannot be replaced by a machine, but machines can supplement a person's ability by doing the bookkeeping and the repetitive work. Through the application of computers and their accessories, GCC has brought mine planning to a more modernized state. The following paper will detail the development and use of one system as used at GCC. Please note: In the figures and tables following, some of the data has been altered to protect confidential information used in mine planning.

Jan 1, 1983

By R. E. H. Pomeroy

The statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Mc Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. % in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5" B., flashing in open test at 199" F. The oil is heated to about 200" F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 Ib. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-08. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and " dog houses" to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent. The draft at the firing end of the furnace is 0.18 in. of water. At the throat or in the uptake above the "verb" the draft is about 1 in.

Jan 1, 1915

Executive Committee. ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. AUGUSTUS H. EUSTIS, Secretary, 131 State St.., Boston, Mass. The twelfth meeting of the Boston Section was held at the Engineers' Club, 2 Commonwealth Ave., Boston, on Monday evening, May 5, 1913, fifteen members and three guests being present.. The meeting Was called to order by Vice-Chairman Albert Sauveur, Who introduced the speaker of the evening, Utley Wedge, of Ardmore. Pa. Mr. Wedge read a, paper on the chloridizing roasting of copper ores, Which lie illustrated With a stereopticon, and Which will be published in full by the Institute. After Mr. Wedge had closed his paper, Which was received with great interest by all the members. the following discussion took place: Professor Hofman said that iron was formerly thought to bo essential to the Henderson process, but that it is not absolutely essential. Mr. Wedge said that., as far as he knew, the presence of some sulphates Was an absolute necessity, and that lime ores can be worked satisfactorily, although lime has an effect on the subsequent leaching. He added that the low fuel consumption of the latest Wedge furnace is a result of direct application of the combustion gases to the ore. Ten per cent. of fuel Was needed with the muffle furnace. By direct firing lie has been able to reduce the fuel needed to from 2 to 4 per cent. In the latest types of furnaces the uses from the upper hearth are not used. There is doubtless some tem-perature at Which the loss from copper chloride volatilization becomes serious, but in practice on Rio Tinto ores troublesome losses are not experienced.. The copper apparently does not become volatile at the temperatures where we would expect that it would. There are doubtless ores in which there would be serious danger from losses from this source. The latest furnaces do not use the high temperatures that Were needed in the former single-hearth Wedge furnaces.

Jan 7, 1913

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry-a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal involves environmental protection and the economics of refuse handling. For over two years, Monterey Coal Co. has operated a non-polluting refuse disposal system at its No. 1 Mine located in Brushy Mound Township of Macoupin County 6 miles south of Carlinville, Illinois. Drainage goes to Spanish Needle Creek and eventually to the Illinois River. The mine produced 3.5 million tons of clean coal during its first two and one-half years of operation and is designed to produce 3 million tpy of clean coal at capacity.

Jan 6, 1973

THE opening session* was held in the hall of the Franklin Institute, on Tuesday evening, June 20th, President Holley in the chair. The President introduced. Mr. Franklin B. Gowen, who addressed the Institute as follows MR. PRESIDENT AND GENTLEMEN : It has been made my pleasant duty to welcome you to the city of Philadelphia, but in so doing I shrink, with some natural reluctance, from appearing before an audience so much better fitted than I am to cope with the subjects which are usually presented to your association, and I can assure you that no trembling neophyte, first venturing within the groves of the Academy, or walking, with sacred reverence, in the gardens of Plato, felt more natural dread at the consequence of his own temerity than I do in appearing before an audience composed of gentlemen belonging to a scientific society of which I am but too sensible that until now I have been a member only in name. In olden times, upon entering a temple sacred to the worship of any deity, it was customary to lay some offering upon the altar, and, in following this custom, it will be my duty, before entering upon the more pleasant part of the task which is assigned me, to call your attention to a subject with which I have been somewhat familiar, and which is entirely within the scope of your investigations, in the belief that I may throw out some hints or some suggestions of a pro¬cess that may be fully developed by some of you, and eventually lead to the introduction of that which may be of service to the human race. The satirist who described the philosopher whom he met, as engaged in the process of extracting sunbeams from cucumbers, * A joint discussion of the subject of Technical Education, by the members of the American Society of Civil Engineers and the American Institute of Mining Engineers, was held in the hall of the Franklin Institute, on Monday evening, June 19th, and Tuesday morning, June 20th. This discussion has been printed in a separate pamphlet by both societies.

Jan 1, 1877