Search Documents

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls' hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls' mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

THE John Fritz Medal Board of Award, at its regu¬lar annual meeting Oct. 19, awarded its gold medal to Herbert Clark Hoover. Thus ended a process of selection begun a few years ago. The award was tentatively made a year ago by the Board, which is composed of sixteen recent past-presidents of the four national societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers, having together a membership of nearly 60,000. The sixteen members of the Board are: American Society of Civil Engineers : C. E. Grunsky, Robert Ridgway, George S. Davison and John F. Stevens ; American Institute of Mining and Metallurgical Engineers: William Kelly, J. V. W. Reynders, Samuel A. Taylor and E. DeGolyer; American Society of Mechanical Engineers: Fred R. Low, D. S. Jacobus, Dexter S. Kimball and Charles M. Schwab; American Institute of Electrical Engineers: Farley Osgood, M. I. Pupin, C. C. Chesney and Bancroft Gherardi.

Jan 1, 1928

By R. D. MacDonald

The search for metalliferrous deposits in the Labrador-Ungava Trough of Canada dates from 1929 when non-ferrous minerals were the main quest of prospectors in this area. Many gossans, resulting from the oxidation of sulfides, were located and examined but none of these led to any orebodies of commercial value. However, such investigations did much to arouse interest in this area and fostered further mapping and prospecting. Since this early period in the history of prospecting in the Trough, the presence of iron ore deposits and potential iron producing sites has commanded the center of attention of exploration personnel. The iron-bearing rocks of southwestern Labrador have in recent years come into prominence as possible sources of iron ore of the beneficiation type. Exploration and development work has been carried on in concession areas granted by the Newfoundland Government to the Labrador Mining and Exploration Co. Ltd. and to the Newfoundland and Labrador Corp. In the course of evaluating its holdings in the Wabush Lake area (Fig. l), Labrador Mining and Exploration Co. has conducted geological, geophysical and diamond drilling programs.

Jan 10, 1960

By N. F. Dyson, T. R. Scott

The iilzfluence of catalytic agents on the oxidation of ZnS has been studied under pressure leaching conditions, using a chemically prepared sample of ZnS which was substantially unreactive on heating at 113°C with dilute sulfuric acid and 250 psi oxygen. Nurnerous prospective catalysts were added at the ratio of 0.024 mole per mole ZnS in the above reaction but pvonounced catalytic activity was confined to copper, bismuth, rutheniuwl, molybdenum, and iron in order of. decreasing effectiveness. In the absence of acid, where sulfate was the sole product of oxidation, catalysis was exhibited by copper and ruthenium only. Parameters affecting the oxidation rate were catalyst concentration, temperature, time, oxygen pressure, and a7riount of acid, the first two being most important. The main product of oxidation in the acid reaction was sulfur, with trinor amounts of sulfate. An electrochemical (galvanic) mechanism has been suggested for the sulfuv-forming reaction, whereby the relatively inert ZnS is "activated" by incorporation of catalyst ions in the lattice and the same catalysts subsequently accelerate the reduction of dissolved oxygen at cathodic sites on the ZnS surface. Insufficient data was obtained to Provide a detailed mechanism for sulfate fornzation, which is favored at low acidities and probably proceeds th'rough intermediate transient species not identified in the preseni work. THE oxidation of zinc sulfide at elevated temperatures and pressures takes place according to the following simplified reactions: ZnS + io2 + H2SO4 — ZnSO4 + SG + HsO [i] ZnS + 20,-ZSO [21 In dilute acid both reactions occur but Reaction [I] is usually predominant, whereas in the absence of acid only Reaction [2] can be observed. Both proceed very slowly with chemically pure zinc sulfide but can be greatly accelerated by the addition of suitable catalysts, as suggested by jorling' in 1954. Nevertheless, an initial success in the pressure leaching of zinc concentrates was achieved by Forward and veltman2 without any deliberate addition of catalytic agents and it was only later that the catalytic role of iron, present in concentrates both as (ZnFe)S and as impurities, was recognized and eventually patented.3 It is now apparent that another catalyst, uiz., copper, may have also played a part in the successful extraction of zinc, since copper sulfate is almost universally used as an activator in the flotation of sphalerite and can be adsorbed on the mineral surface in sufficient amount The importance of catalysis in oxidation-reduction reactions such as those cited above has been emphasized by various writers and Halpern4 sums up the situation when he writes that "there is good reason to believe that such ions (e.g., Cu) may exert an important catalytic influence on the various homogeneous and heterogeneous reactions which occur during leaching, particularly of sulfides, thus affecting not only the leaching rates but also the nature of the final products." Nevertheless relatively little work has appeared on this topic, one of the main reasons being that sufficiently pure samples of sulfide minerals are difficult to prepare or obtain. When it is realized that 1 part Cu in 2000 parts of ZnS is sufficient to exert a pronounced catalytic effect, the magnitude of the purity problem is evident. An incentive to undertake the present work was that an adequate supply of "pure" zinc sulfide became available. When preliminary tests established that the material, despite its large surface area, was substantially unreactive under pressure leaching conditions, the inference was made that it was sufficiently free from catalytic impurities to be suitable for studies in which known amounts of potential catalytic agents could be added. The first objective in the following work was to identify those ions or compounds which accelerate the reaction rate and, for practical reasons, to determine the effects of parameters such as amgunt of catalyst, temperature, time, acid concentration, and oxygen pressure. The second and ultimately the more important objective was to make use of the experimental results to further our knowledge of the reaction mechanisms occurring under pressure leaching conditions. The fact that catalysts can dramatically increase the reaction rate suggests that physical factors such as absorption of gaseous oxygen, transport of reactants and products, and so forth, are not of major importance under the experimental conditions employed and an opportunity is thereby provided to concentrate on the heterogeneous reaction on the surface of the sulfide particles. As will appear in the sequel, the first of these objectives has been achieved in a semiquantitative fashion but a great deal still remains to be clarified in the field of reaction mechanisms. EXPERIMENTAL a) Materials. The white zinc sulfide used was a chemically prepared "Laboratory Reagent" material (B.D.H.) and X-ray diffraction tests showed it to contain both sphalerite and wurtzite. The specific surface area, measured by argon absorption at 77"K, varied between 3.9 and 4.6 sq m per g. Analysis gave 65.0 pct Zn (67.1 pct theory) and 31.9 pct S (32.9 pct theory). Other metallic sulfides (CdS, FeS, and so forth) used in the experiments were also chemical preparations of "Laboratory Reagent" grade. Samples of mar ma-

Jan 1, 1969

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

The adsorption density of ethyl xanthate on pyrite was determined as a function of xanthate concentration. Surface preparation of the mineral appears to have asafunctionsome effect on the subsequent adsorption process, A monolayer of xanthate on the surface is exceeded only in presence of oxygen. The effect of OH- , HS- (and x and CN- S=)and on the amount of xanthate adsorbed was investigated. Competition between OH- and X- (xanthate) ions for specific adsorption sites is indicated over a wide pH range. IN the flotation of sulfide ores, xanthates are most commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena' and for chalcocite.2 In the work on chal-cocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh.9 ut the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5;4 at neutrality, a contact angle of 60" is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants. In this study of pyrite collection the writers have sought to relate measured xanthate adsorption to the method used in preparing pyrite, to the presence or absence of oxygen, to concentration of hydroxyl, hydrosulfide, sulfide, and cyanide ions. The principal experimental tool has been radioanalysis," " using xanthatcx marked with sulfur 35. Experimental Materials Pyrite: Unlike most sulfides, pyrite is a poly-sulfide. The structure given by Bragg7 resembles that of sodium chloride, the iron atoms corresponding to the position of sodium and pairs of sulfur atoms corresponding to the position of chlorine. The edge of the unit cell in pyrite is 5.40 A and in halite 5.63 A. The S-S distance in pyrite is 2.10 A; the Fe-S distance, 3.50 A: and the Fe-Fe distance, 3.82 A. Natural pyrite from Park City, Utah, was used in this investigation. Pyrite 1 was obtained by hand picking pure crystals. Pyrite 2 and Pyrite 3 were obtained from finer textured crystalline material containing inclusions of silicates. The same cleaning technique was utilized for the preparation of Pyrite 2 and Pyrite 3, whereas a different cleaning technique was used for Pyrite 1. Pyrite 1 was prepared as follows: The crystals were ground in a porcelain ball mill and the 200/400 mesh fraction was separated by wet screening with distilled water, followed by washing for 1 hr with deoxygenated distilled water acidified with sulfuric acid to pH 1.5. The acid was removed by rinsing with deoxygenated distilled water on a filter until a pH of 6.0 was reached in the effluent. This filtration was carried out under nitrogen. The sample was then dried in a desiccator under nitrogen. The period of time for which this pyrite sample was in contact with water containing oxygen was about 4 hr. The specific surface as determined by the BET gas adsorption method was 582 cm2 per g. Final material assayed 53.12 pct sulfur and 46.5 pct iron (theoretical, for FeS,: S, 53.45 pct; Fe, 46.55 pct). After crushing, Pyrite 2 and Pyrite 3 were washed with 1 M HCl. rinsed, and fed to a laboratory shakinq table to remove the small amount of silicates. The concentrate obtained was ground in a laboratory steel ball mill. The 200/400 mesh fraction was separated by classification in a Richards hindered settling tube. This fraction was then given a final wash with 0.1 M HCl and deoxygenated water was filtered through the sample. The final effluent showed a conductivity equivalent to that of a solution having a salt concentration of 0.3 ppm. Aqueous hydrogen sulfide solution was then added to the sampln (about 100 ml saturated H,S solution to about 1000 g pyrite under a few hundred milliliters of water) which was stored wet under nitrogen. The sample stored in this manner showed no indication of formation of iron oxides, whereas iron oxides appeared

Jan 1, 1957

By C. W. Mallett

The distribution and properties of interseam and overburden rocks in coal mines is largely controlled by conditions at the time of their original deposition. Within the developed areas of the Bowen Basin, depositional environments range from fluvial through upper and lower detaic, to marginal marine and intertidal facies. Each environment has a characteristic association of lithologies with specific range of properties, and each lithology has a characteristic geometry. Fragmentation problems are associated with ancient sand channel systems, where the difficulties encountered depend on the dimension and shape of channels, their continuity, orientation to mining face and associated sediment bodies formed as levees or interdistributary muds. Stability problems in spoil, pit floor and highwalls are usually associated with mudstones which contain swelling clays derived from the original Permian volcanic source. This clay problem is aggravated by deep Tertiary weathering. Case studies are presented of detailed analyses and prediction of geomechanical properties on a mine site scale. These are used in investigating or forecasting fragmentation and stability hazards. The studies incorporate detailed field mapping, bore log data and computer data processing. They allow the development of detailed depositional models for specific interseam intervals within mines. As areas of depositional environment are identified they allow the construction of maps of similar mining conditions and the determination of the most suitable mining techniques.

Jan 1, 1983

IRON AND STEEL COMMITTEE ALBERT SAUVEUR, Chairman A. A. STEVENSON, Vice-Chairman HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. Guilliaem Aertsen, Henry M. Howe, E. Gybbon Spilsbury, John Birkinbine, _Robert-W. Hunt, J, S. Unger; William-H. Blauvelt, J:-E: Johnson, Jr., Felix A: Vogel; Charles A. Buck, Charles Kirchhoff, Leonard Waldo, Ernest F. Burchard, Richard Moldenke, William R. Walker, F. D. Carney, Charles F. Rand, William R. Webster, James Gayley, Joseph W. Richards, Frederick W. Wood. Henry D. Hibbard, C. F. W. Rys, There will be a meeting of the Institute in Pittsburg on Oct. 8, 9, and 10, 1914. This meeting will be under the joint auspices of the Iron and Steel Committee, the Committee on Coal and Coke, and the Committee on Petroleum and Gas. The iron and steel papers will probably be presented on Oct. 8. The following papers have been received and accepted and will be read at the October meeting.

Jan 6, 1914

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum, tungsten, and the binary alloys thereof were grown by electron-beam zone melting and tested in tension between 77° and 373°K. The ductile-to-brittle transition temperature increased sharply with solute concentration, for both tungsten-rich and tantalum-rich alloys; apparently, the maximum transition temperature exists near the 50 pet concentration. Twinning was observed to be a consequence of cleavage-crack propagation. Cleavage occurred on(100)planes, and extensive tearing and "river markings" were present. The onset of brittleness could not be associated with any change in deformation mode, the yield point phenomenon, or the large rise in yield stress with decreasing temperature. Cleavage was observed to initiate at either the specimen surface, or subgrain boundaries. The observation was made that the grain boundaries of Polycrystalline materials are probably even better as nucleation sites for fracture, and are responsible for brittleness at high temperatures and lower solute concentrations than those of the corresponding single crystals. TUNGSTEN and tantalum, the two high-melting neighbors in the third transition period of the periodic table, present striking contrasts. Although both are bee, tungsten has far higher elastic moduli, and the highest ductile-to-brittle transition (DBT) of all the pure metals.' Tantalum, however, is ductile at liquid helium temperatures. Large strain aging and yield point phenomena are observed in tantalum,2,3 but only to a lesser extent in tungsten.4 Tungsten work-hardens at a high rate,5 whereas this effect is negligible in tantalum.' Since the mutual solid solubility of these two metals is complete,7 and no ordering has yet been reported in the binary system, the possibility of depressing tungsten's DBT by tantalum additions was considered. Also, tungsten additions to tantalum could produce hard, high-melting alloys which might be ductile at room temperature. Such alloys offered excellent bases for complex alloy development, particularly with regard to the effect of rhenium on Group VI metals.8"10 In addition, there was the opportunity to examine flow and fracture modes in the vicinity of the DBT, with particular emphasis on the correlation between brittleness and fundamental deformation mechanisms. Myers11 has reported that recrystallized alloys with up to 10 pet W in tantalum are ductile at room temperature, but alloys with 20 pct W could not be swaged at temperatures as high as 500°C. The whole spectrum of Ta-W alloys has been surveyed by Braun, Sedlatschek, and Kiefferl2 using sintered powder compacts. In addition to some physical properties they reported a maximum hardness at about 50 at. pet W, dropping to much lower hardness levels for the pure components. They were able to cold work tantalum-base alloys with as much as 30 pet W and to warm work tungsten-base alloys with up to 20 pet Ta by procedures similar to those used for pure tungsten. EXPERIMENTAL In order to study deformation modes and to keep the impurity concentrations at a minimum, electron-beam zone melting was used to prepare single crystals of high purity. The electron-beam zone melting apparatus is similar to that described by Calverley, Davis, and ever" and incorporates a grid control rectifier to maintain control of emission current. Pure metals were refined by making three zone passes at 4 mm per min up the rod. Alloys were prepared by melting together wire of one constituent on a previously melted rod of the major constituent. Subsequently, two zone passes were made in opposite directions to level the composition after the manner suggested by pfann.14 Purification of the starting materials was accomplished by evaporation of the several impurities, and the degree to which this was accomplished is indicated in the chemical analyses of Table I. The uniformity of composition along a zone levelled rod was within the i 1 pet accuracy of the fluorescent X-ray technique used to determine composition. Crystallographic orientation of the

Jan 1, 1962

By Herbert Hoover

YOUR committee asks that I speak today on the relations of the engineering profession to public affairs. That takes in a lot of ground. This being a cheerful occasion, I will assume that I should exclude the engineer's function as a taxpayer. This being a nonpartisan occasion, I will assume that I should not refer to his voting emotions in 1940. Perhaps what was in the minds of your committee was the application of engineering thought to the confusions of the times. That is also a lot of ground. I fear, however, its boundaries disappear in mirages and rainbows on all sides. Now any entry of the engineer into public affairs involves his breaking into the fields of the sociologists, the economists, and the politicians. However I don't know why, seeing the difficulties these professions are having, they should not welcome a little help.

Jan 1, 1939

By K. R. Janowski, H. Conrad

As part of a program to establish the effect of crystal imperfections on laser output, a detailed study was made of the dislocation structure of ruby crystals obtained from varioius sources. Using KHSO4 as an etchant, a detailed mapping of the dislocation structure on the (0001) and the (1150) planes was carried out. A less extensive study was made of the rhombohedral planes. The average dislocation density on the basal plane was 1.5 to 3 x 106 cm&apos;2 and on the (1120) planes -5 x 10&apos; cm-2. Howe7!er, considerable variation existed between areas on a given plane. The subboundaries in the basal plane tended to lie along [1100] type directions while those on the (1120) plane tended to lie: a) parallel to the basal plane, b) along truces of the (1101) plane, and c) along normals to the traces of the (0001) planes. The orientations suggest that mang of the dislocations lie on the (0001), (1701), and (1150) planes A Laue back-rellection nnalysis Of c-axis wander in one crystal revealed a gradual increase in misorientation from me end of the crystal to the other, with a maximum variation of 1°35&apos;. Slight etching of a mechanically polished crystal revealed mumerous polishing scratches, suggesting the existence of a plastic flow layer. It is recognized that chromium concentration, lineage, and other crystalline imperfections play a role in the efficiency of ruby lasers.&apos; Consequently, it is desirable to establish in detail the imperfection structure of ruby crystals to be used as lasers. Some exploratory work along this line had already been done by Barnes&apos; and Dils and Martin.&apos;" How- referred to as the morphological system, as described by Kronberg.4 The Miller indices given in the present paper will be based on this morphological system. In this system, the three common growth planes are the (0001), the {1120}, and the {1101}.5 Since these planes are of high stability, it is expected that they are most suitable for study by the etch-pit technique. In the present investigation, a detailed mapping of the dislocation structure was carried out for the (0001) and the (1130) planes. A less extensive study was made of the etch-pit structure on rhombohedra1 planes. An analysis of dislocations in sapphire (the ruby host) was first made by kronberg,4 who postulated that slip on the (0001) plane occurred by motion of dislocations with Burgers vector 1/3 <1150> and that these dislocations might dissociate into quarter partials. An etch-pit technique using boiling phosphoric acid was developed by Scheuplein and Gibbs6, 7 for identifying dislocations intersecting the (0001) planes and the planes near (2021) in sapphire. Al-ford and Stephens8 were able to reveal dislocations on the (0001) and {1120} planes in sapphire and ruby by etching in fused potassium bisulfate (KHS04) at 675°C. The termini of basal dislocations [(000l), <1120>] were revealed by Palmour and Kriegel9 on {1120} and {1010} by thermally etching sapphire. Bond and Harvey10 were able to decorate dislocations in sapphire by adding 1 pet by weight of ZrO2 to the Al2O3 powder used in the growth of the crystals by the Verneuil technique and then heating the grown crystals for 4 hr at 1500°C. They found, using optical transmission microscopy, that many dislocations had straight segments which were parallel to one of the six [1120] directions in the basal plane. Single dislocation lines curved smoothly from one alignment to the other, turning through angles of 60 to 120 deg. Also observed were isolated hexagonal loops, approximately 10 µ in diameter, the sides of which lay along the same directions as did the longer dislocations. MATERIAL AND ETCHING PROCEDURE The ruby specimens used in this study (all containing approximately 0.04 pet Cr) had been obtained from four different sources: Linde Co., Meller Co., Valpey Crystal Corp., and those grown at Aerospace Corp.* For the initial phase of this study, several specimens were cut from the slab shown schematically in Fig. 1 which had previously been cut from a disk boule obtained from the Linde

Jan 1, 1964

By J. E. Owen

EXPERIMENTS on twenty-six drilling muds were carried out in an effort to establish a correlation between the apparent viscosity values for these muds as obtained with the Marsh funnel and the Stormer viscometer. This required a calibration of both instruments in which the density of the calibrating liquids was taken into account. Corresponding to the Marsh-funnel viscosity values that were obtained at 1500 c.c. in, 1 qt. out, equivalent Stormer viscosity values were obtained at a Stormer cylinder test speed of approximately 1100 r.p.m. Further, a linear relation between the logarithms of the Stormer cylinder test speed and the resulting apparent viscosity was found to exist for the muds tested for 200 to 1000 r.p.m. The significance of the slope of this linear relationship is discussed as it applies to the field use of drilling muds. It was concluded that Marsh-funnel viscosity measurements are expressible in absolute units that may be correlated with Stormer viscosity measurements, provided these are made in the manner described in the paper. INTRODUCTION The Marsh funnel is used almost universally to determine the viscosity of drilling muds in the field. The Stormer viscometer is commonly used to determine the viscosity of drilling muds in the laboratory. With the Marsh funnel, the time required for one quart of mud to flow out of the funnel originally filled with 1500 c.c. is often taken as the measurement of viscosity. With the Stormer instrument, drilling mud is tested at a cylinder speed of 600 r.p.m. and by means of calibration data the apparent viscosity is expressed in absolute units. Neither of these instruments is an absolute viscometer, and apparent viscosities obtained with either are influenced by the arbitrarily standardized conditions under which the measurements are made. It is disconcerting to the man in the field to be told that laboratory measurements of the viscosities of a group of muds differ widely, when he has already observed that they have identical viscosities when tested in the Marsh funnel. Drilling muds are not perfect fluids, therefore it is not surprising to find a lack of correlation between the apparent viscosity of a mud as determined with the Marsh funnel and that determined with the Stormer viscometer. The work described here was undertaken to develop a correlation between Marsh-funnel and Stormer viscosity measurements. To a considerable degree this has been accomplished. This study has resulted not only in a better understanding of the two viscosity instruments and the data obtainable from them, but has given considerable information regarding the viscosity characteristics of drilling muds. EXPERIMENTAL PROCEDURE Calibration of Harsh Funnel and Stormer Viscometer The first step in the experimental procedure was the calibration of the Marsh funnel and the Stormer viscometer with

Jan 1, 1941

In discussing Mr. Keller&apos;s paper, I quoted the results obtained by Mr. Allan Gibb, correctly crediting them to Mr. Gibb, with due reference to the report in which they were published. But in the table immediately following, and in my further remarks, following the table, I find that, by some clerical or other error which I cannot, after the lapse of time, explain, I spoke of Mr. Gibb as Mr. "Dean"—a metallurgist who had written on a related subject, but not on the point I was discussing. In short, my reference throughout was to the work of Mr. Gibb; and by reading a Gibb " for a Dean " in all places on pp. 832 and 835 where the latter name occurs, my remarks will be brought into accordance with my intention, and with the facts.

Jan 1, 1901

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By Oscar E. Harder

THE TERM "physical metallurgy&apos; is used in the title of this lecture in preference to "metallography ?because the former has a broader meaning with most audiences, some people thinking of the latter as being limited to work with the microscope. This distinction, how- ever, has not been held by the out- standing workers in the field of metallography, such as the late Professor Sauveur. In the broadest sense metallography is essentially the same as physical metallurgy. The American Society for Testing Materials has adopted-the following definition: "Metallography is that branch of science which relates to the constitution and structure, and their relation to the properties of metals and alloys." This definition might be improved by adding after "properties" -"and their industrial and scientific uses." Metallography has also been defined as the science of metals and alloys. Physical metallurgy is to be distinguished from process metallurgy in that the latter relates particularly to the production of metals from the ores.

Jan 1, 1940

By Lawrence Wright

ON the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly con-demned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings.

Jan 1, 1938

By D. R. Maneval

The Surface Mining Act of 1977 required a study by the National Academy of Sciences regarding the special mine reclamation requirements of Alaska. The status of mines operating and planned in Alaska will be presented. New mines opening in Alaska must establish a baseline inventory of plants and animals in the mine site area as well as determine pre-mining air and water quality. Current work in these areas will be summarized. Reclamation practices in Alaska and other Arctic countries as practiced currently will be described. A summary of current research in Alaska dealing with revegetation on surface mined lanais, re-establishment of animal populations, and water treatment processes necessary in this pristine environment will be discussed. Included will be future predictions of the direction of mine reclamation in Alaska as more mines enter the industry.

Jan 1, 1984

By Harry Udin

IN 1948, the writer and his associates determined the surface tension of solid copper by balancing the force of surface tension in a very fine wire against an external load.&apos; At that time we, in common with other early workers, assumed that grain boundary energy in a pure metal is very small in comparison to the energy of an external surface. Accordingly, we neglected the internal surface energy of the coarse-grained specimens. Since that time, experimental evidence has accumulated showing that grain boundary energy, far from being small, is generally about one-third of the energy of an external surface.2-4 This is sufficient to introduce a significant error into our determination. The differential equation governing equilibrium is: wdl - yds, + y*ds2 [I] rather than wdl = yds as originally written. w is the balancing force in dynes, 1 the length of the specimen, sl the external and s2, the internal surface area, y the copper/ copper vapor surface tension, and y* the grain boundary tension. Fortunately, we had made for another purpose a careful study of the size and shape of the grains, and found that the boundaries, with rare exceptions, traversed the specimens and were perpendicular to the wire axis. For this case, eq 1 leads to w = rry -(n) r2y* [2] where r is the wire radius and (n is the number of grains per unit length. A count of some twenty 5-mil wires indicated that - n became 80 & 10 after a short anneal near the melting point, and remained nearly constant for as long as 96 hr at temperature. An assumption of y* = 1/3y leads to a defining eauation for r: [31 The term in the brackets may be considered a correction factor applied to eq 11 of ref. 1. Upon applying this factor, the surface tension of solid copper at its melting point is found to be 1650 & 100 dynes per cm, rather than 1370 as previously reported.&apos; The new temperature coefficient is —0.55 dynes per cm per "C. Grain boundary energy is more significant than surface energy to the physical metallurgist. It is evident from eq 2 that a series of experiments with wires of different grain size can lead to an evaluation of y*. The details of such an experiment are being worked out now. References 1 H. Udin, A. J. Shaler, and J. Wulff: The Surface Tension of Solid Copper. Trans. AIME, 185, 186-190; Journal of Metals (Feb. 1949) TP 25303. 2 G. L. C. Bailey and H. C. Watkins: Surface Energies in the System Solid Copper-Molten Lead. Proceedings Physical Society. (London) (1950) 36B, 350. 3 L. H. VanVlack: Inter granular Energy of Iron and Some Iron Alloys. Ph.D. Dissertation, Univ. of Chicago, Sept. 1950. 4 . P. Greenough: Grain Boundary Energies in Silver. R.A.E. Report, No. Met. 52. (May 1950) Fan-borough, Hants, England.

Jan 1, 1952