Search Documents

By Edward H. Robie

EIGHT years ago in this department we had a column on the daiquiri cocktail, which, as we pointed out at that time, was invented by mining engineers. Since then we have said little or nothing about alcoholic drinks, but having set the precedent perhaps we may now pass along a little information about martinis. We have observed that as an aperitif the martini has become increasingly popular with men, so much so that we always feel a bit peculiar if we order something else. And the call is not for just a martini either; it must be a dry martini, and some of our friends are extremely particular on this point. The matter has achieved such importance that The New York Times devoted half a page to it a few Sundays back. Several recipes are given which may be useful to some of our members when entertaining visitors from this part of the country: The standard martini is said to be half gin, half Italian vermouth, two dashes orange bitters, and a pickled onion and twist of lemon peel. This progresses to the very dry martini, which calls for five parts gin and one part vermouth with an onion, olive, or lemon peel. Several alternatives are offered for the manufacture of the very, very dry martini. One is to pour a little vermouth into the mixing glass and pour it out again before mixing gin and ice. A second way is to put the ice in a sieve, hold it over the sink, and pour a little vermouth over it; then put the ice in the mixing glass. A third is to let the draft from an electric fan blow across an open vermouth bottle toward the mixing glass. Then the ultimate is the awfully dry martini, obtained by setting the vermouth bottle next to the mixing glass and turning the bottle slowly so that the label is exposed to the gin for perhaps a second. The Times notes that Mr. Martini himself personally prefers vermouth and soda.

Jan 1, 1952

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,' and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,' and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By J. F. Wolff

CARL ZAPFFE, Brainerd, Minn. (communication to the Secretary*).¬Unless one has actually directed explorations for iron ore, it is doubtful whether the importance of Mr. Wolff's paper, the value of the information contained, and the large amount of detail work involved in what is set forth can be fully appreciated. It is indeed rare to get such a com-

Jan 3, 1917

By AIME AIME

BLANDFORD. C. BURGESS, the new Chairman of the Industrial Minerals Division, took the advice of Horace Greeley in reverse-he turned his hack on San Francisco and the Golden Gate, and after a few side excursions toward Alaska and Arizona, hit the trail eastward, not for the lonesome pine, but for Spruce Pine, N. C. Born Aug. 10, 1893, in San Francisco. Burgess found his first job, shortly after finishing high school at 19, as axeman for a surveying party of engineers working for the Southern Pacific Co. in Oregon. Later he moved on up with them into Alaska. He liked the engineering profession, and decided to equip himself further so he entered the University of California in the fall of 1913. and for the next two years devoted himself to acquiring an education in civil engineering.

Jan 1, 1945

Elected Died 1882 *ABBOTT, ARTHUR V 1906 1903 * ADAMS, CHARLES C. 1905 1884 *ADDY, MATTHEW 1896 1894 *ALLFN R B 1896 1874 *AMIOT, H 1892 1886 *AMSLER, CARL 1894 1895 *ÅNGSTROM, CARL 1901 1895 *ARMSTRONG, JOHN F 1898 1882 *ARNOLDS, HUGO 1886 1875 *ASHBURNER, CHARLES A 1889 1872 *ASIIBURNER, WILLIAM 1887 1883 *ATKINS, C M , JR 1885 1897 *AYERS, WILLIAM 1898 1885 *BABCOCK, GEO H 1893 1884 *BAILEY, EDWARD 1889 1880 *BAILEY, JACKSON 1887 1900 *BALLOU, FRANKLIN 1903 1886 *BARNES, F W 1892

Jan 1, 1910

By H. W. Gillett

CLYDE WILLIAMS has reminded me that in the fall of 1929, gave, in MINING AND METALLURGY, an account of the hopes and aspirations of Battelle Memorial Institute, which was then just swinging into initial operation; and that therein I remarked that B.M.I. should stand, as well, for Better Metallurgical Industries, since helping to better them was the Institute's aim. So he has suggested that some of the betterments of the past fifteen years might well be listed. A yearly summary of progress comes pretty close to the ultimate in futility, for everything proved of value in that year had its inception in earlier years, and everything really new has still to be proved. Plenty of things hailed as wonderful achievements for that year, by some enthusiasts invited to contribute to the summary, turn out in later years to be inglorious flops. But over a decade and a half, betterments that are really such become self-evident, and recounting some of them can be done without guesswork or wishful thinking. An inventory of what was known and utilized in 1929 compared to what is now known and used is not too hard to make. Perhaps the most clear-cut picture of what is known and used at a certain date is drawn by the handbooks, textbooks, and equipment catalogs of that date, with scientific periodical literature forecasting what knowledge may later be used when it is verified and assimilated. The tools available for production or for research limit the application of old and the finding of new knowledge.

Jan 1, 1945

Aalde, Kaare, (S'40) Box 827, Socorro, N. M. Aase, Glenn D., (S'40) Engr. Experiment Sta., Univ. of Utah, Salt Lake City, Utah. Abadesco, Enrique A., (S'39) Student. College of Engrg., Univ- of the Philippines, Manila, P. 1. Abbott, John L., (S'40) Met. Engr., Engr. Trainee. Wright Aeronantical Corp., Paterson, N. .J. Abbott, Robert H., (S'42). Agricultural & Mech. College of Texas, College Sta., Tex. Abreu, Ovidio M., (S'38) Dept. of Geol., Compauia Cousulidada de Petroleo, Caracas, Venezuela. Acomb, Allen, (S'41) 3921 Chestnut St., New Or¬ leans, La. Adam, Howard W., (S'41) Montana School of Mines, Butte, Mont. Adams, Charles E., (S'42) Uuiv. of California, Los Angeles, Calif. Adams, Charles W., (S'39) Student, Michigan Col¬ lege of Min. & Tech., Houghton, Mich. Adams, H. Travis, (S'39) 310 South 5th St., Bur¬ bank, Calif. Adams, John W., (S'42) Univ. of Texas, Austin, Tex. Adams, Rob L., (S'40) Lt., B. 0. C. No. 12, Fort Sill, Okla. Adamson, Charles R., (S'41) Uuiv. of Utah, Salt Lake City, Utah.

Jan 1, 1942

By I. A. Lesk

The various materials utilized in the construction of integrated circuits, and the resultant materials interfaces, are discussed with emphasis on a materials system that is compatible with all types of integrated circuits and minimizes the number of different interfaces. Problems with interfaces may originate in the silicon, on its surface, and between other materials within the integrated-circuit package independent of the silicon. ThE difference between integrated-circuit theory and practice may generally be spelled out in terms of the difficulties in fabricating a desired structure. There are, of course, problems in forming the requisite materials, of the necessary composition and geometry, where needed. A distinct class of problem, however, is associated with interfaces— generally between different materials, but occasionally between regions of the same material. We require that each interfacial system perform its proper electrical, mechanical, and thermal function, and do so in an unchanging manner with time under the most severe operating conditions. In a practical sense, we deal in nonideal systems, such that it is generally not possible to form an interface exactly the way it was intended, even if we allow for a knowledge of the practical limitations of the fabrication system. Another way of looking at this situation is to realize that, when we form a group of interfaces under apparently the same experimental conditions, there are often differences of important consequence between them. Very high-magnification pictures, such as are obtained by an electron microscope, reveal fine structure that often differs over the area of a given sample, as well as from sample to sample. Low-magnification pictures look better, but don't eliminate the problem. The trend towards integrated circuits, and away from circuits fabricated utilizing separate components, is very strong in many areas of electronics. A typical silicon monolithic integrated circuit, still in place in the wafer on which it was fabricated, is shown in Fig. 1. The increased reliability which is being experienced through the use of integrated circuits can, to a large extent, be credited to the reduced complexity of the interface system that is present in the electronic system. A glance at Fig. 1, however, with all of its epitaxial and diffused p-n junctions, and interconnect system, shows that interfaces have been far from eliminated. Fig. 2, depicting a schematic cross-sectional view of a (partial) typical integrated circuit, illustrates in detail the numerous interfaces that occur in this type of structure. Besides the individual circuit elements, there are interfaces for isolation, and, Fig. 3, even a crossover requires a series of interfaces. What has been accomplished, however, irrespective of whether or not the total number of interfaces in the circuit is increased or decreased, is that the variety of interfaces is very much reduced. This is because there are fewer materials involved. Since the expense incurred in an R & D program to improve reliability is pretty much directly proportional to the variety of interfaces involved, it is economically advisable to work with integrated circuits for highest reliability. That is not to say that circuits built using standard components could not be made as reliable as integrated circuits, but that the expense involved because of the more complex over-all interface system would be much greater. Although electronic performance utilizing integrated circuits with all silicon elements (i.e., transistors, diodes, resistors, capacitors) is adequate for many applications, there are numerous instances where thin-film passive elements must

Jan 1, 1965

ON Oct. 5, 1926, the day before the general ses-sions of the fall meeting of the American Insti-tute of Mining and Metallurgical Engineers at Pittsburgh, a round table conference on the combus-tibility and testing of coke was held at the Bureau of Mines Experiment Station. There were about fifty present, with A. C. Fieldner, chief chemist of the Bureau of Mines, as chairman. The following organi-zations were represented: American Institute of Min-ing and Metallurgical Engineers, American Society for Testing Materials, American Gas Association, Eastern States Blast Furnace and Coke Oven Association, Gas and Fuel Division of, American Chemical Society, and Southern Ohio Pig Iron and Coke Association. In opening the proceedings, Mr. Fieldner explained that the meeting had been called at the suggestion of several members of the Institute and members of other organizations. The subject is of interest to the pro-ducer and the user of coke whether it be in a blast furnace, cupola furnace, house-heating furnace, open grate, gas producer, or in a water-gas generator. There has been much confusion on this subject largely because there is no common definition of combustibility. Does the blast-furnace superintendent, the coke-oven operator, and the fuel engineer have the same under-standing of the term "combustibility"? If a common understanding can be reached, many differences of opinion will disappear. COMBUSTIBILITY OF COKE R. H. Sweetser of Columbus, Ohio, disagreed with the statement of P. H. Royster, T. L. Joseph, and S. P. Kinney in Reports of Investigations, Serial No. 2524, of the Bureau of Mines, in which it was stated that the coke-oven op-erator cannot change coke combustibility by modifying oven practice. Mr. Sweetser held that the coke-oven man can change the combustibility of coke. Blast-furnace men know that coke that will burn easily with low pressure and will. come down in the regular way in the furnace can be pro-duced from a given mixture of coal. His idea of the combustibility of coke is the rate of flow through the com-bustion zone of the blast furnace. If the coke does not pass through in normal manner it is highly incombustible. H. J. Rose of the Koppers Co., Pittsburgh, objected to being pinned down so closely on this phase of the com-bustibility and incombustibility of coke. Coke-oven men are frequently obliged to change oven conditions to make a coke which gives blast-furnace men what they want. The size of the coke and the screening have an important bear-ing on combustibility, and there are many cases on record where by simply changing the different sizes of the coke, everything worked smoothly, and that is a much more combustible coke.

Jan 1, 1927

By J. Murray Riddell, George A. Morrison

This paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.‡ Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Bar-berton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 2-40 ft. Fractured sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra- turn of oil-bearing sandstone one foot thick was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), ? by 4 by 4-in. angle irons; spacing of sets. 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. The Shaft-sinking Operation The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (1) a storage pocket of 300 cu. ft, capacity with truck servicing facilities, and (2) pneu matically operated dump doors, which mere actuated by the hoistman, thus caring

Jan 1, 1946

By Winston W. Spencer

ALTHOUGH by far the largest A consumer of platinum metals in the world, the United States until recently has been in- significant as a producer. Writing in the "Minerals Yearbook" for 1939, H. W. Davis states that 1938 probably marked the beginning of an- other period of transition in the world production of the platinum metals. In that year, he says, their production in the United States jumped to 49,380 oz., or fourth in the rank of world output. In the ten-year period 1925 to 1934 United States output ,averaged only 8300 oz. Practically all of this sudden in- crease in production is attributable to the introduction of mechanized equipment at the placer deposits in the Goodnews Bay district of Alaska. This district adjoins the Bering Sea and Kuskokwim Bay (accented on the first syllable), and is approximately 120 miles south of the mouth of the Kuskokwim River. The nearest village and post office is Platinum, which lies about eleven miles north- east of the Goodnews Bay Mining Company's camp. A good gravel road connects the mine camp and the village.

Jan 1, 1940

GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1938 and reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Mining and Metal¬lurgy (Magazine), Library, Speakers for Local Sections and Student Societies, and Student Relations. To these reports members are referred for further details. Membership.-The end of the year 1938 saw Institute membership at an all-time peak: 12,474, made up of 2898 Student Associates and 9576 members of other classifications. The next highest level had been reached at the end of 1921 when corresponding figures were: total, 10,329; student members, 1450; all other classifications, 8879. The net gain for the year was 1495, of which 751 were Student Associates and 744 in the other categories. Two factors contribute to the growth of membership: (1) the enrolment of new members; and (2) the retention of members already on the roll as reflected in a relatively small number of resignations and suspensions for nonpayment of dues. For the first, much credit goes properly to the general Membership Committee that functioned for a second year under the chairmanship of Clyde E. Williams. With the cooperation of Institute members in general, to whom Mr. Williams expresses appreciation in his report, the Committee has been successful in acquainting eligible nonmembers with the purposes, activities and advantages of the Institute. The result has been the receipt during the year of 1162 applications, exclusive of Student Associates. This compares with 1212 during 1937 and 1266 during 1936. However, in considering this modest decline, account must be taken of the somewhat less prosperous conditions prevailing in the mineral industries and, consequently, among engineers engaged ?in those industries.

Jan 1, 1939

By J. L. Bruce, G. W. Nicolson

ThE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydro-thern~ally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CeMent and Concrete Linings During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, howcver, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 11\2 pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with 12 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concretc and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1949

Elected Died 1882 *ABBOTT, ARTHUR V 1906 1903 * ADAMS, CHARLES C. 1905 1884 *ADDY, MATTHEW 1896 1894 *ALLFN R B 1896 1874 *AMIOT, H 1892 1886 *AMSLER, CARL 1894 1895 *ÅNGSTROM, CARL 1901 1895 *ARMSTRONG, JOHN F 1898 1882 *ARNOLDS, HUGO 1886 1875 *ASHBURNER, CHARLES A 1889 1872 *ASIIBURNER, WILLIAM 1887 1883 *ATKINS, C M , JR 1885 1897 *AYERS, WILLIAM 1898 1885 *BABCOCK, GEO H 1893 1884 *BAILEY, EDWARD 1889 1880 *BAILEY, JACKSON 1887 1900 *BALLOU, FRANKLIN 1903 1886 *BARNES, F W 1892

Jan 1, 1910

By Kim Beattie

IN spite of the fact that in 1944 Canada experienced a decline in production of all her leading base metals-nickel, zinc, lead, and copper; despite uncured headaches in the coal-mining industry; and cheerfully ignoring a still further drop in gold, the most valuable product of her mines, which had the lowest output of any year since 1931, the Canadian miner retains the traditional optimism of miners everywhere as he looks forward to the postwar period. Some factors should keep the Canadian mining industry from being too optimistic of the coming era of peace, but the fraternity generally holds that its confident attitude towards the future is based on sound reasons. The decline in production in the Canadian mining industry last year can be almost wholly attributed to the serious shortage of labor and the difficulty in obtaining transport and supplies in remote areas. Some falling off occurred in the demand for certain strategic metals, but the diversion of gold miners, especially, without replacements being obtainable, to direct war work or allied pursuits, was certainly the principal cause of the reduced output in 1944. But that is a situation which will right itself at the close of the conflict.

Jan 1, 1945

By T. Sterry Hunt

Jan 1, 1884

By Subhas G. Malghan

Feldspathic deposits occur widely throughout the United States, but North Carolina, California, Connecticut, and South Carolina accounted for over 80% of the total domestic feldspar output for the year 1973.1 Pegmatites and granites constitute the major feldspar reserves of the United States, 2 and in addition, feldspar is produced as a byproduct by firms whose major products are spodumene and mica. 3 Feldspar flotation is practiced in the United States, Mexico, Finland, Norway, West Germany, Japan, and the USSR. According to the US Bureau of Mines estimates, the production of feldspar in the United States and rest of the world were 704,000 and 2,514,000 t, respectively. Feldspar is principally used as a flux in making glass, pottery, porcelain, enamel, tile, and other ceramic products. In recent years, the domestic feldspar industry is faced with a number of problems. As a result of increased cost of energy and the introduction in 1972 of new legislative programs relating to air, water, and noise pollution, land-use restrictions, and mined-land rehabilitation, the production costs have increased. Apart from the increased cost of operation, an operational problem exists with the feldspar producers in North Carolina, especially those in the Spruce Pine area. This problem is concerned with the use of hydrofluoric acid in the feldspar flotation. Feldspar producers in Spruce Pine, NC, have been discharging process waste water into the North Toe River. The mill waste water contains active fluoride ions. Fluoride in excessive concentrations is undesirable in waters used for drinking. It is stated that water containing 0.9-1.0 ppm fluoride will seldom cause mottled enamel on children's teeth; and for adults, concentrations less than 3-4 are not likely to cause endemic cumulative fluorosis and skeletal effect. Although the literature on this subject is rather confusing and inconclusive, the inference that concentrations over 4 ppm may affect bone structure is clear. According to the recent Federal Register,4 maximum fluoride level of 1.4 ppm at 79°-98°F is considered to be adequate and safe for the protection of health of the consumers. The EPA and state environmental agencies have accelerated their drive to reduce water pollution on a faster schedule. By 1977, the EPA specifications for maximum contaminant level of fluoride ions in the discharge waters of feldspar milling operatins is expected to be reduced to 2.0 ppm. The other problems of using hydrofluoric acid are the following: toxicity, hazards of handling and storage, and high cost as compared to other inorganic acids (almost 16 times the cost of sulfuric acid). In order to reduce fluoride levels in mill discharge waters, mining companies have taken the following steps: I) Recirculating a part of their mill water. Even though recirculation of mill water seems to be a novel method of reducing fluoride contamination of the discharge water, there are certain operational and handling problems. 2) Conducting research on the treatment of fluorides in mill waste water. The technology of treatment of fluoride ions has received considerable interest in the recent years. A recent research report5 estimates that the cost of fluoride ion removal to meet the present specifications in the feldspar industry is approximately $0.25/t of ore processed, and about $0.50/t of feldspar produced. At the request of the feldspar producing industries in North Carolina, the North Carolina State University (NCSU) Minerals Research Laboratory has taken up a research program directed towards overcoming the fluoride ion pollution problem. After a close study of the operational, technical, and economic aspects of feldspar flotation, it was decided to attempt to replace the conventional hydrofluoric acid process. Conventional Feldspar Flotatin Using Hydrofluoric Acid Since the inception of the feldspar flotation process using hydrofluoric acid by O'Meara2,6 the process has achieved a great commercial success. In the conventional flotation separation of feldspar-quartz, hydrofluoric acid is used to suppress quartz and activate feldspar, and a long chain amine salt (acetate or chloride) is used as a collector. The bulk of amine collectors used in current feldspar operations are applied as the water-soluble acetates of the free-base amines. These products are pastes or waxy solids which are available in a range of acetic acid neutralization levels generally 50 to 100% neutralized. In spite of the problems mentioned in connection with the use of hydrofluoric acid, this process is extremely stable with respect to changes in the process variables. With the exception of a few operations, alaskite and pegmatite are the major sources of feldspar.7 In the flotation treatment of a pegmatite that contains iron-bearing minerals (heavy minerals), mica, feldspar, and silica, a logical order of removal presents itself considering the following:8 1) Mica is readily floated by an amine collector in a pulp pH 3.5. Some iron-bearing minerals will usually respond to amine collector in acid circuit with the mica concentrate. 2) Since iron minerals tend to occur invariably in the feldspar concentrate, it is desirable to remove most of these prior to feldspar flotation. A fatty acid or a petroleum sulfonate collector used in this flotation step in acid circuit will float iron-bearing minerals. 3) Using hydrofluoric acid to maintain pH of 2.5, an amine collector employed in a final step will float feldspar away from silica, usually leaving the latter in the tailing as a high-grade silica concentrate. The problems connected with the flotation separation of feldspar-quartz arise due to the similarities in their chemical structure. Therefore, any reagent system that is likely to succeed in feldspar-quartz separation should have adsorption affinity towards one of the minerals and depression effect towards the other mineral.

Jan 1, 1979

President-Mrs John R C Mann, 90 Edgemont Road, Scarsdale, N Y First Vice-President-Mrs C P Pollock, 27 Dante Street, Larchmont, N Y. Second Vice-President-Mrs Mendum B Littlefield, 40 Lincoln Street, Larchmont, N Y Third Vice-President-Mrs J B Cunningham, 236 East 2nd St , Tucson, Ariz Fourth Vice-President-Mrs Theodore Loftus, 410 Cowles St, Fairbanks, Alaska Fifth Vice-President-Mrs George L Craig, 109 Calumet Avenue, Calu¬met, Mich Recording Secretary-Mrs Arnold H Miller, 601 West 115th St, New York 25, N Y Assistant Recording Secretary-Mrs R J Mechin, 66 East 79th St, New York 21, N Y Corresponding Secretary-Mrs John A Poulin, 4 East 70th St , New York 21, N Y Treasurer-Mrs Robert W Rowen, 29 West 39th Street, Room 914, New York 18, N Y Assistant Treasurer-Mrs Samuel H Dolbear, 1000 Park Avenue, New York 28, N Y Assistant Treasurer-Mrs Roger H Sherman, 8 Roman Avenue, Forest Hills Gardens 75, N Y.

Jan 1, 1957

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915