Search Documents

By C. M. Moncrief

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By T. J. Woods

Tars paper deals with the origin, definition and prevention of scabs an semifinished rolled-steel product. Mold coatings, which are considered essential in scab prevention, were found to be effective only in relation to the ingot surface of semikilled and killed steels and not necessary for the rolled product. That is to say, the scabs on ingots caused by having been cast in uncoated molds are eliminated in the soaking and rolling operations, therefore are not present on the rolled product. This fact, which is contrary to the average opinion, was established after extensive and thorough experiments had proved the ordinary conception of the origin of scabs to be incorrect. This subject may be of little or no concern to steel plants producing small ingots for the manufacture of small billets and bars, except as it may be of interest in showing why their surface troubles with scabs do not exist on the product of heats with normal pouring practice. But to the producer of large ingots to be rolled into slabs for large plates used in shipbuilding, it is a very important subject. DEFINITION OF A SCAB The generally accepted opinion is that the individual scabs present on rolled products (as shown by Fig. I) are considered to have been individual splashes on the ingot surface. This opinion was found to be incorrect. Experiments showed that there were no individual scabs on the product that had appeared as individuals on the ingot surface. The single scabs seen are either pieces of a shell that is present near the bottom of all top-cast ingots, or a veneer that may be present on any part of an ingot improperly poured, as when the stream strikes the mold wall. This definition is based on a detailed study of scabs and their characteristics in which the following have been found true: Location.- On the product of heats poured without trouble, scabs, if present, are always on the product that corresponds to the bottom end of the ingot, and usually occur in clusters, This is true whether molds are coated or not. Shape.-There is no regularity as to shape, size or thickness. It is sometimes possible to separate a few pieces and place them together, like pieces of a jigsaw puzzle, indicating that at one time they had been united as one piece. If individual splashes were the origin of scabs, the foregoing would not be true. Instead, the splashes, which occur throughout the pouring of the ingots, would be present uniformly over the entire product and there would be considerable similarity in the shape and thickness of the scabs. EXPERIMENTAL WORK Our experimental work was conducted on 200-ton heats of semikilled plate steel tapped into an oval ladle 15 ft. high. All ingots were top-cast direct into 24 by 54 by 82-in. molds, straight-sided, set on fat stools. Two separate studies were made about one year apart, each study extending

Jan 1, 1943

By AIME AIME

FOR many years it has been the invariable custom of the Institute, in addition to its annual meeting in February, to hold a technical meeting in the fall in some mining or metallurgical center in the West. As the activities of the Institute have increased, and especially since the absorption 'of the American Institute of Metals, there have for a number of years been two fall meetings. Never before in the history of the Institute have there been three meetings in addition to the annual meeting in February; in 1920, however, three important fall meetings are to be held. The general Institute trip will be made this fall to the Lake Superior iron and copper country. Members will leave Buffalo on August 20 by steamer, visit the copper mines in and about Houghton, the iron mines of the Marquette and Iron Ranges of Michigan and the iron mines of the Mesabi Range in Minnesota, and' return to Buffalo by steamer on September 3. Technical sessions will be held at Houghton, Minneapolis and Duluth. For a long period it was customary for the Institute to visit the Lake Superior country about every seven years. This trip, however, will be the first visit since 1904. The unprecedented development in both copper and iron mining in this section during this period will make this trip of unusual importance. In addition, a notable series of papers will be presented.

Jan 1, 1920

By Arthur S. Dwight

THE professional career of Thomas Septimus Austin, who died at El Paso, Tex., August 23, 1906, was contemporaneous with the growth of the silver-lead smelting-industry of the Far West, to which his talents and zeal contributed in no small degree. Born at Stratford, Conn., December 7, 1853, he was the seventh son in a family of thirteen. His parents were well-to-do; and he received a thorough preliminary training at the Hopkins Grammar School, New Haven, Conn., passing thence to the Columbia School of Mines, in New York, where he was graduated in 1876. His first professional work was that of analytical chemist with a Cuban sugar company. In this position he spent a year, and, whatever else of benefit he may have acquired during that year in Cuba, he gained a facility of speech in the Spanish language which was of inestimable value in his subsequent work in Mexico and the southwestern United States. In 1877, he went to the Rocky Mountains, and, under the firm name of Murphy & Austin, opened an assay-office in Leadville, Colo., which was just then coming into public notice as a rich silver-lead camp. The next year, however, he entered the service of the Germania Smelting & Refining Co. at Salt Lake City, Utah, where he remained until 1882, first as assayer and chemist, and later as Assistant Superintendent. The Germanic bears the honorable distinction of being one of the first of the large " custom " lead-smelters erected in the West. Its founders may be called the pioneers of the modern lead-smelting practice, and the Germania served, to a large extent, as a model for the many plants that sprang into existence during the next few years in Utah, southern Idaho, Colorado and other lead-producing districts. The formulation, for the first

Jan 1, 1908

By Luiz C. Correa da Silva, Robert F. Mehl

An experimental study of the movement of markers in the systems Cu/a-brass, Cu/Sna-solid solution, Cu/Ala-solid solution, Cu/Ni, Cu/Au, Ag/Au, employing many types of markers and a variety of temperatures. Marker movement is confirmed and undoubtedly associated with the manner in which atoms move during diffusion. EVERAL years ago Smigelskas and Kirkendall' •S reported measurements on the interdiffusion of copper and a-brass and on the movement of inert markers placed at the original join. These markers were observed to move toward the a-brass side of the join, and from this it was inferred that zinc diffuses in a-brass more rapidly than copper. Similar results were reported a little earlier for the diffusion of solvents into high polymer solids.' This has attracted much attention, particularly from those interested in the mechanism and the theory of diffusion: Seitz3 has employed it in supporting the vacancy theory of diffusion; from the data Darken4 has calculated separate diffusion coefficients for copper and zinc, developing a "phenomenological" theory of diffusion; and Bardeen5 has employed it in constructing a general theory, including therein the work of Seitz and Darken, as has Le Claire. These matters have recently been reconsidered in a sympo~ium.7 Some reason has existed for questioning the work of Smigelskas and Kirkendall.' Their technique consisted in electroplating copper on a-brass, upon the surface of which Mo-wires had been secured, and then diffusing, measuring the extent of diffusion along the normal to the join, and measuring the marker displacement in the same direction by a comparator determination of the distance between Mo-wires on opposite sides of the electroplated brass sample. It has been suspected that the copper plate might have been porous, and that the original interface might have been an imperfect join, both contributing to the transfer of the volatile zinc by vapor transfer;' it has also been questioned whether the marker movement might not in a measure be a property of the marker itself; etc. These legitimate questions require experimental answers; the present paper offers such answers. Moreover, Smigelskas and Kirkendall studied the effect only in the Cu-Zn system and at one temperature; the attention which the work of Smigelskas and Kirkendall has commanded recommends similar

Jan 1, 1952

By Simon D. Strauss

The world appetite for minerals in the, third quarter of this century grew at a higher rate than had been anticipated. To illustrate, consider the experience of four, commodities. Excluding the Communist bloc, sometimes referred to as the centrally planned economies, demand for aluminum increased at a compound rate of 8.6% between 1950 and 1975,; copper rose by 4.4%; iron ore by 5.5%; and tin, the laggard in the group, by 2%. Except for tin, the figures are substantially greater than growth rates anticipated in 1950 in the Paley Commission report and other studies. The growth rate was not evenly distributed in geographical areas. Professor Wilfred Malenbaum of the University of Pennsylvania did an interesting study breaking these figures down as among three principal sources of demand -- the United States, other industrialized nations (which he referred to as the "rich lands"), and the developing world (which he referred to as the "poor lands").

Jan 1, 1982

LEHIGH UNIVERSITY On April 25, the Mining and Geological Society of Lehigh University held a meeting and elected. the following officers for the college year 1918-1919: C. S. SCHUBERT, President, C. G. GILMAN, Vice-president, H. TSAI, Secretary, E. D. HOLLINSHEAD, Treasurer, C. N. TOMLINSON, A. A. KORVES, Curators. After a short business meeting the Society was favored by three interesting and instructive talks. Mr. C. A. Bonine spoke on the "U. S. Geological Survey" and showed a number of beautiful lantern slides; Mr. R. Rosenbaum read a paper on "Geodes;" and Prof. B. L. Miller presented a brief discussion on "War Minerals." H. TSAI, Secretary.

Jan 7, 1918

By Edmond S. Miksch

The morphology and growth rate of ice grown in supercooled water are markedly affected by convection of the water. A dendritic ice sheet with water flowing past the dendrite tip exhibits deflection of the dendrite spine toward the upstream direction, accelerated growth of secondary spines on the upstream side, and suppression 01" secondaries on the downstream side. Flow causes a thin disk to become corrugated, the corrugations being parallel to the flow. Flow causes an increase in the growth rate of the ice. IF a small seed of ice is placed in slightly supercooled water, it grows initially as a disk with the axis of the disk parallel to the c axis of the ice crystal.' It appears that growth in the c direction is inhibited, while growth occurs with equal facility in all directions in the basal plane. It appears that growth rate as a function of interface temperature is very nearly equal for all directions similarly oriented relative to the c axis. Subsequent to the discoid growth, branching occurs and dendrites develop. The primary dendrite spines grow parallel to the six equivalent a axes of the crystal. Secondary, and in some cases, tertiary spines also grow in these directions. The highly anisotropic: dendritic growth indicates that there must be some finite difference of growth rate for different directions in the basal plane. These differences must be quite small, however, since if they were large, the discoid mode would not occur. Hence, it was expected that the dendrite growth direction could be deflected from the crystallographic direction by perturbation of the thermal field at the dendrite tip. Experiments were done in which perturbation of the thermal field was accomplished by causing the supercooled water to flow past the dendrite tip. The flow direction was perpendicular to the c axis of the crystal, and was perpendicular to the primary spine of the unperturbed crystal. Supercooled water was supplied by a 15 cm cubical copper box, which was refrigerated and insulated so it could cool water to temperatures down to —2oC, and maintain the temperature constant to O.l°C for the duration of a run. A lucite channel of rectangular cross-section, 12 by 24 mm, was mounted horizontally in the box, with one end open so water could flow into it, and the other end leading out through the wall of the box to a length of tubing leading: to an orifice plate 123 cm below. cnunMn s MIKSCH, MemberAiMe, formerly Research Associate, Research Associate, Fig. l(b)—Vertical section of apparatus A horizontal cross-section is shown in Fig. l(a), and a vertical section is shown in Fig. l(b). Means for observing the ice are shown in Fig. l(a). Collimated light passes through the ice sheet and forms an image on the ground glass screen. A lucite box containing dry air was employed to prevent condensation. Ice of the desired orientation was provided by the seed holder shown in Fig. l(b). This device was made of lucite, and had a reservoir in which ice could be frozen by placing it in a freezer. This reservoir com-unicated with the outside only through a narrow gap between two sheets of lucite. The seed holder (after ice had been washed off its exterior) was immersed in the tank of supercooled water, the narrow gap terminating in a slot in the top of the flow channel. Ice growing through a thin water layer in the gap between the two sheets of lucite was oriented so its c axis was perpendicular to the sheets. This orientation is an application of a growth phenomenon2 which causes ice growing along a smooth solid surface in supercooled water to orient itself so its c axis is normal to the surface. After the ice grew into the channel, further orientation was necessary, since the direction of the a axis

Jan 1, 1970

By A. Muan

Liquidus data are presented for mixtures in the ternary system FeO-Fe2O3-SiO2 in equilibrium with a gas phase with O2 pressures ranging from 10-10.9 to 1 atm. Data obtained are combined with previously published data to construct lines of equal 02 pressures and lines of equal CO2/H2 mixing ratios along the liquidus surface. Courses of crystallization of selected mixtures under conditions of constant total composition, constant O2 pressures, and constant CO2/H2 mixing ratios are discussed. PHASE equilibrium studies of silicate systems where iron is one component are complicated by the fact that iron readily occurs in three different states of oxidation: Fe3+, Fe2+, and Fe0. Success or failure in work with iron silicate systems is to a large extent dependent on control of the oxidation state of iron and all investigations therefore must be carried out under carefully controlled atmospheric conditions. Silicate systems containing only strongly electropositive metals (like Na+, Ca2+, Mg", etc.) can, for simplicity, be treated as condensed systems, that is, the gas phase can be neglected and the phase relationships discussed in terms of the phase rule written in the well known simplified form P + F = C + 1. In the case of iron silicate systems, however, the composition of the condensed phases varies with the gas composition, and a complete picture of phase relationships can be obtained only by varying the gas composition over a wide range. In order to understand the phase relationships in the more complicated multicomponent silicate systems with iron oxide as one of the constituents, a knowledge of the ternary system FeO-Fe2O3-SiO2 is essential, since it constitutes a bounding portion of all such systems. It was with this in mind that the present study was undertaken. Previous Work A considerable amount of work has been done on various aspects of the chemistry and metallurgy of systems containing silica and iron oxides. The two bounding binary systems FeO-Fe2O3 and FeO-SiO2" The first attempt to obtain information on phase relationships of iron oxide-SiO, mixtures at different 0, pressures was made by Greig.' Darken" determined the melting points of iron oxide on solid silica under various atmospheric conditions. Darken did not determine experimentally the composition of the melts at liquidus temperatures but discussed very ably the principles involved in applying the phase rule to the system. In a recent study Schuhmann, Powell, and Michal8 determined experimentally the liquidus surface of a portion of the ternary system and combined the new information with data in the literature to construct a phase diagram. Their method was briefly as follows: Homogeneous mixtures with various contents of SiO2, FeO, and Fe2O3 were made up by melting together stock mixtures in various proportions. Samples of the homogeneous mixtures, the compositions of which were determined by chemical analysis, were then heated in platinum crucibles in an inert atmosphere until equilibrium among the condensed phases was achieved. The samples were quenched to room temperature and the phases present determined by microscopic examination. Assuming that no change in composition takes place during the equilibration run in inert atmosphere, the liquidus surface can be determined, but no information is obtained regarding the partial pressures of 0, of the gas phase in equilibrium with the condensed phases. The author's method, to be described in the next section, permitted the location of points at the liquidus surface as well as a calculation of the corresponding partial pressures of O2. Experimental Method General Procedure: The standard quenching technique was adapted for a study under controlled variable atmospheric conditions. Premelted mixtures of silica and iron oxides in platinum envelopes were held at constant temperature under chosen atmospheric conditions until equilibrium was reached among solid, liquid, and gas phases. The sample was then quenched to room temperature, the phases present identified, and, for the most significant runs, the composition was determined by chemical analysis. The corresponding partial pressure of 0, was calculated from known equilibrium constants of the gas reactions occuring in the furnace atmosphere. Materials: Starting materials were oxides of commercially highest available purity; cp silicic acid was dehydrated by heating to 1350°C for 6 hr and cp Fe2O3 was dried at 400° C for the same length of time. Samples of 10 g were made up by mixing

Jan 1, 1956

By T. S. Lovering

The Moffat tunnel passes through the continental divide about 50 miles west of Denver, Colo., on the Denver & Salt Lake R. R.: It is 16 ft. wide, 24 ft. high, and 32,383 ft. long, a distance of a little more than 6 miles. The advantages accruing from its construction may be briefly summarized as follows: The tunnel eliminates 27 miles of grade averaging more than 3.5 per cent. and actually running well over 4 per cent. in many places, and changes the steepest grade from 4.5 to 2 per cent. It reduced the peak of the railroad from 11,660 to 9249 ft. which enables one engine to pull four times as much freight as it could before the tunnel was built. If the Denver & Salt Lake R. R. completes its line, this road will shorten the distance between Denver and Salt Lake City by 200 miles and will have no steeper grades than the lines now connecting the two cities. The proposal to drive the tunnel through the divide dates back about 25 years and D. H. Moffat, who was the leading spirit in the organization of the Denver & Salt Lake R. R. spent much of his time and energy in efforts to raise money for the tunnel that bears his name. He was unsuccessful and died before the work was started. In 1920 an effort was made to obtain state legislation favoring a bond issue to finance three important railroad tunnels in Colorado but the measure was defeated, largely through the efforts of the citizens of the region near Pueblo. A few years later devastating floods caused the Pueblo voters to seek relief from the state and at this time they withdrew their objection to the tunnel bond issue. As a result, a $6,720,000 bond was issued to finance the Moffat tunnel. Construction bids were so high that the work was finally allotted on a scheme analogous to a cost-plus basis. The contract was awarded to Hitchcock and Tinckler, who are paid a fee of $140,000 for driving the tunnel. All bills are paid by the Moffat Tunnel Commission. The contract was let Sept. 19, 1923, and Hitchcock and Tinckler agreed to complete the work by July 19, 1927. In the event of finishing before this date they were to be given a bonus of $1000 a day and

Jan 1, 1928

The John Fritz Medal is awarded from time to time for notable scientific or industrial achievement by a board composed of representatives from the four engineering Societies. The members of the Board of Award for 1917 are: A. S. C. E. A. S. M. E. George F. Swain Ambrose Swasey, Charles Warren hunt, John, A. Brashear, Charles D. Marx, Frederick R. Hutton, Clemens Herschel. John R. Freeman. A. I. M. E. A. I. E. E. Gybbon Spilsbury, C. 0. Mailloux, Charles F. Rand , Paul M. Lincoln, Christopher R. Corning, John J. Carty, Benjamin B. Thayer. Harold W. Buck. The John Fritz Medal was awarded in January, 1917, to Dr. Henry Marion Howe, for his "investigations in metallurgy, especially in the metallography of Iron and Steel." The presentation ceremonies were held in the Auditorium of the United Engineering Societies' Building, New York, on Thursday evening, May 10. Mr. Ambrose Swasey, Chairman of the John Fritz Medal Board of Award, presided, and addresses were delivered by Dr. Rossiter W. Raymond, Secretary Emeritus of the American Institute of Mining Engineers, and Dr. Ira N. Hollis, President of the American Society of Mechanical Engineers. Professor Albert Sauveur, Chairman of the Board at the time the award was made, presented the medal, and the ceremonies concluded with the response of Dr. Howe.

Jan 7, 1917

By T. D. Tiemann

The chemical and mineralogical composition of Caribbean bauxite ores are described. Extraction of alumina by several processes from both Haiti and Jamaica bauxites is discussed and data presented. IMMENSE deposits of bauxite occur in the Caribbean islands of Hispaniola and Jamaica in the high plateau lands and have been excellently described by 0. C. Schmedeman.' The bauxite occurs as deposits in catchments or etched depressions in Tertiary limestone believed to have been deposited in the Eocene and Oligocene periods.' In appearance both the Haiti and Jamaica bauxites resemble a relatively high iron clay and have indeed been mistaken for such.' They are very soft and friable and disperse readily on vigorous agitation in water. The color range in general is light brown to red. Chemically, the outstanding characteristic of the bauxites is the low silica and high ferric oxide content. The extremely low silica makes them particularly valuable for the production of alumina in the Bayer plant since silica is responsible for the loss of both alumina and soda chemically combined as XNa,OYSiO2,ZAl2O2. The ferric oxide, only traces of ferrous iron are present, offers no interference in the production of high grade alumina. Typical oxide analyses of three types of ore are given in Table I2 and a list of the elements occurring in spectrographic quantities in Table 11." The size of the individual particles in the ore makes successful petrographic examination extremely difficult. The ores contain some relatively coarse grains of heavy minerals such as ilmenite, magnetite, and rutile, but other than occasional crystals of a few microns, the greater portion of the minerals are submicroscopic in size and approach colloidal dimensions. The mineralogic composition of the ores has been investigated by X-ray and differential thermal analysis.' These investigations indicate that the predominant mineral phases present are gibbsite (A1203.3H2O), boehmite (Al2O3.H2O), hematite (Fe2O3), and goethite (Fe2O3-H2O). There is no evidence of the occurrence of diaspore (Al2O3.H2O) in either the Haiti or Jamaica ores, but some type of "amorphous" alumina may be present in some of the bauxites of Jamaica." The temperature stability regions in the alumina-water system have been investigated and are given in recent literature. In the temperature range where the hydrated forms are stable, as determined by hydrothermal bomb methods," ibbsite is the stable phase to 155°C (311°F), boehmite from 155°C (311°F) to 280°C (536oF), and diaspore from 280°C (536°F) to 450°C (842°F). Although quite similar in many characteristics, the Haiti and Jamaica ore show a divergence in mineralogic composition that is reflected in the extractability of the alumina described in later paragraphs. Two principal differences occur in mineralogic composition. The iron-bearing mineral in the Haiti ores is predominantly hematite, while in the Jamaica ores goethite is predominant.4 Directly related to the extraction of alumina are the two minerals, gibbsite and boehmite. Boehmite is relatively high in the Haiti ores and in some of the less soluble Jamaica ores, while gibbsite predominates in the ores in Jamaica amenable to the American Bayer process of extraction. Pedersen and Related Processes In general, all processes for the extraction of alumina involving sintering or fusion of bauxite ores with limestone, soda ash, or a combination of limestone and soda ash followed by leaching, are based on the formation of alumina compounds that. yield alumina soluble in the subsequent leach. The principal idealized reactions in respect to alumina and silica for the three types of processes are as follows: Soda Ash Sinter: A12O3 + Na2CO3 = Na2O-Al2O, + CO2 SiO2 + Na2CO3 = Na2O . SiO2 + CO2 A12O2 + SiO2 + Na2CO3 = Na2O.Al2O8. SiO2 + CO2 Leach (with excess water): H2O + Na2O-A12O3 = 2 NaOH + A12O3 (insolution) H2O + Na2O-SiO2 = 2 NaOH + SiO2 (in solution) Soda Ash— Limestone Sinter: Na2CO2 + A12O3 = Na2O.A1203 + CO2 2CaCO3 + SiO2 = 2CaO . SiO2 + 2CO2 Leach (with excess water): Na2O' A1208 + H2O = 2NaOH + A13O3 (in solution) These latter reactions are the basis of the sinter process currently used for the recovery of soda and

Jan 1, 1952

By George Mah, Charles Wert

Internal-friction peaks caused by diffusion of oxygen and nitrogen have been observed in ytterbium. They are thought to be caused by the redistribution, under stress, of strain dipoles around an interstitial oxygen or nitrogen and a neighboring substitutional impurity. With the use of a simple geometrical model, diffusion coefficients for oxygen and nitrogen between special interstitial sites have been calculated. a) APPLICATION OF INTERNAL FRICTION TO MEASUREMENT OF DIFFUSION RATES IN DISSOLVED INTERSTITIAL ATOMS In bcc metals, the interstitial atoms occupy the centers of cube faces (0, 1/2, 1/2), or their equivalents, the center of the cube edges (0, 0, 1/2). An interstitial atom in this position causes an aniso-tropic distortion in the lattice. When stress is applied, mechanical relaxation can take place by the movements of the interstitial atoms. This relaxation has been used to obtain information concerning the movements of the interstitial atoms in the bcc metals. Data for these alloys have been compiled by Stanley and Wert. Other researchers have extended the investigation of interstitial diffusion to the close-packed metals. Gupta and weinig2 found an oxygen peak in a titanium, the height of which is linearly dependent on the oxygen concentration. They assumed, therefore, that they were dealing with movement of atomic ally dispersed oxygen in titanium. KG and wang3 determined that the diffusion coefficients of carbon in fcc steels and in nickel obtained by internal-friction methods were consistent with those obtained by macrodiffusion methods at much higher temperatures. Bisogni found oxygen and nitrogen peaks in hafnium by use of which he deduced the diffusion coefficient of these gases in hafnium. He observed further that the half-widths of these peaks corresponded almost exactly with those of a single-relaxation process; he assumed it to be caused by movement of atomically dispersed oxygen and nitrogen. From these studies, the deduction can be drawn that, in general, diffusion data can also be obtained for the interstitial diffusion in close-packed metals (or more precisely, in slightly impure close-packed metals). One group of such metals for which little data exist for the diffusion of dissolved oxygen and nitrogen is the rare earths. They have great affinity for gases, which enter solution interstitially. In this investigation results were obtained for the Yb-O and Yb-N interstitial solid solutions with traces of substitutional impurities; these solid solutions are of fcc structure. b) MECHANISM OF THE RELAXATION IN FCC CRYSTALS In the fcc structure, an interstitial gas atom is usually situated in the octahedral position (1/2, 1/2,

Jan 1, 1964

By R. V. Lundquist

R. T. Hukki (Finland Institute of Technology, Helsinki, Finland)—Two schools of thought are developing concerning the order of the rate of flotation. The paper by Morris is intended to show experimental evidence in favor of the first order rate. Arbiter, on the other hand, has presented an earlier paper" to demonstrate the validity of the second order rate equation. Unfortunately his method of plotting is open to criticism, as pointed out by Morris." A more sensitive method of plotting has been described by the writer,= whereby the data presented by Arbiter demonstrate the superiority of the second order plot. The general rate equation may be written in the following forms for the integrated first and second order equations: (A) t =------In—-------- (first order) [4] 1 1 (B) — = — kc, + KC°²— (second order) [5] t R As a first approximation the value of C, may be taken as a unity, 100 pct or 1. Whether or not this is the case in all tests performed by Morris is impossible to judge, owing to the fact that the flotation times are extremely short, e.g. 150 sec in tests A. It would, indeed, be very interesting to know what the total recovery R would be after 1 hr of flotation, for example, instead of after 150 sec. Certainly there are circumstances when C, approaches unity within a very small

Jan 1, 1954

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature microhardness of as-grown and annealed MoaC single crystals was measured on the (0001), {2110), and1012) planes using Knoop and Vickevs indenters at loads ranging front 25 to 1000 g. The orientatimz dependence of hardness with respect to crystal axes was also studied. The average random hardness of as-grown crystals was determined to be 1520 kg per sq nm. Annealing to 2000°C decreased. the average hardness by 150 units. An increase in hardness after annealing at 2200 ;C was noted. Optical and electron microscopy revealed slip and twin traces on all planes studied, as produced by mi-cvohavdness indentations. Basal (0001)(2i10) slip was determined to be the primary slip system and was substantiated by electron transmission microscopy. A secondary {1010)(2110) slip was produced by mi-crohardness indentations. The lattev also produced twinning- of the {10i2)[0001] type, as proven by electron diffraction. Electrical resistivity and elastic-modulus anisotropy were found and correlated with hardness anisotropy and Mo2C crystal structure. Elastic-modulus values were obtained by microhard-uess and ullrasonic methods. Bonding mechanism of Mo2C is discussed. ROOM-TEMPERATURE microhardness indentations are useful for studying hardness anisotropy, slip, and twinning in brittle materials. Slip has previously been produced in this manner in and WS~~.~ Recently, the authors5 reported slip of the {10i0)(11~0) type produced by high pressure and microhardness indentations on hexagonal TiBz (c/a = 1.066) single and polycrystals. This slip system was also reported by French and ~homas' and Taka-hashi and ~reise~ for hexagonal WC (c/a = 0.976) crystals. These results suggest that prismatic rather than basal slip is favored in hexagonal nonmetallic materials having a c/a ratio considerably less than the ideal (1.633). Buerger precession and cylindrical X-ray rotation patterns were previously' taken on cleaved sections of the Mo2C single crystals studied in this work. Th~y were found to be hexagonal MoaC with a. = 3.0233A, co = 4.7344A, and C/O = 1.5660. The latter ratio is close to that of the beryllium metal (c/a = 1.57), which slips primarily on the (0001) plane: but also slips on the (1010) planes.'0 ~irconium" (c/u = 1.59) and titanium12 (c/o = 1.59) deform mainly by slip on nonbasal planes which contain a close-packed direction. This is due to the fact that for these two metals the initial resolved shear stress for slip on the (10i0) prismatic planes is lower than that on the (0001) plane. The prominence of basal rather than prismatic slip in metals of high c/o ratios is shown by cadmium (c/a = 1.89), zinc (c/a = 1.86), and magnesium (c/a = 1.62) which deform mainly by basal slip. However, in case of the latter, by stressing magnesium crystals in tension or compression parallel to the basal plane, slip on (10i0) planes can also be produced.13 Several hardness values for polycrystalline Mo2C are reported in the literature: Biickle ' and Samsonov'~ give a value of 1800 and 1479 kg per sq mm, respectively, at a 100-g load; and Kieffer and Benesovsk~'~ report a value of 1950 kg per sq mm at a 50-g load. ~ott'~ reports a Vickers hardness value of 2000 kg per sq mm, with the load unspecified. A Rockwell A hardness value of RA = 88 has also been reported.'' In the present work, for comparison with single-crystal Mo2C hardness values, a Khnloo value of 1600 It 150 kg per sq mm was found on 99.6 pct pure and 99 pct dense hot-pressed Mo2C. This work was undertaken partly to explain the considerable differences in hardness values reported for polycrystalline Mo2C. EXPERIMENTAL The Mo2C single crystals investigated were prepared by a Verneuil-type process using an electric arc by the Linde Co. of the Union Carbide Corp.lg The largest specimens grown were boules 7 mm in diam by 40 mm in length. The crystals had an average density of 9.04 g per cu cm, with a Mo + C content of 99.8 wt pct. The major impurities were: 100 ppm each Na, Zr, and Ca; 85 ppm 0, 55 ppm Fe, and 10 ppm each Cr and Ta. The crystals were found to be carbon-poor, the average carbon content being 5.73 wt pct (stoichiometric value is 5.89 pct). The molybdenum content was found to be 94.08 pct, which is nearly stoichiometric. Electron-microprobe traverses of selected specimens were done with a Phillips-AMR microanalyzer. Thin-film and carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to optical and electron-optical studies, specimens were mounted in Lucite and polished on a vibratory polisher using diamond-paste grades ranging from 9-1 p and Linde A powder for up to 48 hr. Dilute nitric acid was used for thin-section polishing and chemical etching for 1-15 min. Electrical-resistivity measurements at room temperature were taken with a Rubicon bridge, using gold contacts. For hardness measurements, a Tukon Microhardness Tester Type FB with Knoop and Vickers indenters was used. Measurements were taken at loads ranging from 25 to 1000 g; however, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Indentations of cracking classes 1 and 2 only were considered for hardness determinations.20)21 (There are six cracking classes, ranging from "class 1" for a perfect inden-

Jan 1, 1967

By George S. Ansell, John B. Hudson, Stephen A. Koffler

The permeability of hydrogen through the a phase of palladium has been measured by a low pressure permeation technique under conditions such that bulk diffusion was the rate-controlling process. The observed permeability is described by the equation: J = 1.80 x 1O-3 P½exp(-3745)/RT) cc(stp)/sec/cm2/en over a range of hydrogen pressure, P, from 2.9 x 10-5 m Hg to 5.0 x 10-3 cm Hg, and over a temperature range, T, from 300" to 709°K. The fact that the permeability shows a square root dependence on pressure and a reciprocal dependence on thickness was taken as evidence that bulk diffusion, rather than surface reactions, was the rate-controlling process. The permeability data were used in conjunction with the solubility data of Salmon et al., to determine the diffusivity of hydrogen through palludium as: D = 4.94 x 10-3 exp(-5745/RT) cm2/sec There was no influence of sub structural defects observed over the temperature range employed. From the permeability data obtained, coupled with grain size measurements, it was concluded that the ratio of grain boundary diffusivity to bulk diffusivity was less than 105 over the range of temperature investigated. THE diffusive mass transport of hydrogen in the a phase of palladium has been studied previously by numerous investigators.' In spite of the large amount of attention this system has received, there is not good agreement between the results obtained in different investigations.' This is due in part to the fact that the mass transport was surface-limited during some of these studies, rather than being diffusion-controlled3-5 The reason for the disagreement in other cases is not clear. These studies made use of such techniques as rate of absorption from solutions6 and gases,' electrochemical potential,8 time lag,' and permeation10,11 to determine the mass transport behavior. Of these, the gas permeability technique is the only method which allows an easy test to determine if diffusion is the rate-controlling mechanism, thus eliminating the uncertainty regarding the limiting transport processes inherent in the other techniques. The two most recent permeability studies are those of Toda10 and Davis." Toda determined the permeability of hydrogen in the a phase of palladium over the temperature range from 170" to 290°C, and over the pressure range from 36 to 630 mm Hg utilizing a steady-state gas-permeability technique. Toda's result was: J = 1.41 x 10-3 P½ exp(-3220/RT) where J = specific permeability in cc(stp)/sec/cm2/cm, P½ = square root of the inlet pressure in (cm Hg)½, R = Universal gas constant, and T = temperature in deg Kelvin. Davis11 also employed a steady-state gas-permeability technique over the temperature range from 200" to 700°C and over the pressure range from 0.02 to 760 mm Hg. His result for the permeability of hydrogen in the a phase of palladium was: J = 3.15 x 10-3 P½ exp(-A440/RT) In the range of overlapping temperature for these two investigations, the values of the specific permeability calculated from the above two equations differ by a factor of about 1.8. In the present investigation, the permeation of hydrogen in the a phase of palladium was determined over a wide temperature range, 27" to 436oC, and over the pressure range from 2.9 x 10-5 to 5.0 x 10-3 cm Hg. This temperature range overlaps that of the previous investigations of Toda and Davis, but also covers the lower temperature range which has never before been investigated. The lower pressure range used here avoided the interaction between the dissolved hydrogen atoms observed at higher hydrogen concentrations.' MATERIALS The as-received palladium specimens were cold rolled from a casting and were supplied as 5.08 cm discs of 0.508 and 0.762 mm thickness. According to J. Bishop and Company specifications, the composition of the discs was 99.95 pct Pd, the balance being Cu, Ag, Au, and Ir. In order to obtain samples of varying grain size, the as-received discs were then heat treated. Sample 1 was treated for eight minutes in a nitrogen atmosphere at 810°C and then air-cooled. Sample D was heated first to 550°C in helium. The helium atmosphere was then immediately replaced by hydrogen and the temperature was slowly raised to 1220°C and held for 22 hr. The sample was then cooled to 550°C where the hydrogen was replaced by helium and the disc was further furnace-cooled to room temperature. Sample H was given the same heat treatment, only with hydrogen substituted for helium below 550°C. The reason that hydrogen was not used throughout the entire annealing cycle for samples D and H was to prevent the distortion encountered by low-temperature cycling in hydrogen observed by Darling." After these heat treatments were completed, the

Jan 1, 1970

By L. Adler

Some estimate of the geologic pressures existine at the site of a proposed underground opening is essential for its economic design and construction. Regardless of the size of such an opening, drill hole, or mine stope, these primitive stresses need evaluation; at present a number of techniques are available for this purpose. However, a new method of analysind stresses is proposed in this paper. Some estimate of the geologic pressures existing at the site of a proposed underground opening is essential for its economic design and construction. Regardless of the size of such an opening, drill hole or mine stope, these primitive stresses need evaluation. At present a number of techniques are available for this purpose, and another one is to be proposed. These may be grouped into three general methods: 1) precedent, 2) instrumentation, and 3) theoretical analysis. The first two are covered in the literature where their advantages, as well as limitations, are discussed.'9' Generally a theoretical approach combines structural geology with engineering mechanics. The former deals with the geodynamic causes of residual stresses (stresses not related to overburden weight) and presents interesting, but controversial, views.'" A general and useful conclusion, however, can be drawn - vertical residual stresses are much less prevalent than horizontal. However, if for some reason, the values and effects of horizontal pressures were better known to engineers the following analysis

Jan 1, 1962

Page Bronze Bearing Metals. By G. H. Clamer............... 162 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. Waring .. 166 The Tin-plate Industry. By D. M. BUck. Discussed by G. H. ClameR, J. W. RICHARDS............................ 168 The Aluminum Bronze Industry. By W. M. Corse............ 171 Bronzes, Bearing Metals, and Solders. By G. K. BURgess and R. W. Woodward. Discussed by G. H. Clamer, R. T. Roberts......... 175 Babbitts and Solder. By G. W. Thompson................ 184 The Cadmium Supply of the United States. By C. E. Siebenthal. Discussed by M. L. Lissberger, C. W. Hill, F. F. ColcoRd.......... 185 Solder, Its Use and Abuse. By M. L. LissbergeR............ 192 Bronze Bearing Metals G. H. ClameR,* Philadelphia, Pa.—Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early days, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 1, 1919

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

Solid-solubility limits at 1500°, l000q and 500°C for carbon, nitrogen, and oxygen in high-purity tantalum were determined by X-ray lattice-parameter methods. For carbon, the solubility was found to be 0.17 at. pct at 1500°C, and less than 0.07 at. pct at 1000°C. A nitrogen solubility of 3.70 at. pct at 1500° C decreases linearly with temperature to 2.75 at. pct at 1000°C, and 1.8 at. pct at 500°C. In the case of oxygen, the solubility was found to be 3.65 at. pct at 1500°C, 2.95 at. pct at 1000°C, and 2.5 at. pct at 500°C. The phases Ta2C, the low-temperature modification of Ta205, and Ta,N of unknown composition but which has a superlattice structure based upon the original bcc tantalum lattice have been identified as the initial precipitates in the respective systems. Metallographic methods were employed to verify the X-ray analyses. The etching behavior of Ta is discussed in terms of lattice i?rzperfections and precipitate phases. The excellent fabricability, high melting point, and nuclear properties of tantalum are responsible for interest in this refractory metal. Data on the solid solubility of the interstitial elements (oxygen, nitrogen, and carbon) in tantalum and on the precipitate phases are somewhat limited. The significant contributions are discussed below. Because the purity of electron-beam melted tantalum (only recently available) is considerably higher than that used in previous studies, the present investigation was initiated. Gebhardt et all-3 have investigated the tantalum-oxygen and tantalum-nitrogen systems with particular reference to the changes in physical properties and to the rates of reaction between these gases and the metal. The solubility of oxygen in tantalum was reported2 to be 3.7 at. pet at 1500°, 2.3 at. pet at 100O°C, and 1.4 at. pct at 750°C. Schonberg4 reported that several oxide phases (Ta40, Ta,O, TaO and Ta,05) exist while X-ray studies by Gebhardtl showed only two oxides, Ta,05 and an unidentified phase which was associated with a platelet-type precipitate. La-gergren and Magneli,' however, questioned the existence of compounds other than the two allotropic modifications of Ta,05 for the tantalum-oxygen system. In the case of nitrogen, the solubility was estab- lished by Gebhardt3 to be of the order of 7 at. pct at 1800°c. The solubility was reported to decrease rapidly with temperature, and, although no limits were established, a precipitate phase was observed by Gebhardt except when the high-nitrogen specimens were cooled very rapidly from the reaction temperature of 1800c. He reported the initial precipitate phase to be a tetragonal distortion of the bcc tantalum lattice while Schonberg6 reported the phase lowest in nitrogen Jo be a cubic super-lattice with a cell size of 10.11 A. Two other nitride phases, Ta,N and TaN, were reported; these appear to be isomor-phous with the carbides of tantalum. The tantalum-carbon system was investigated by Ellinger7 and by Lesser and Braurer. Two compounds, Ta,C and TaC, were reported to exist, each with a range of composition. The solubility of carbon in tantalum was found to be practically nil at all temperatures. Thus, of the interstitial elements which are present in small amounts in high-purity tantalum, carbon might be expected to form precipitates. The present investigation was initiated to obtain additional data on the solid-solubility limits of these interstitials at 1500°, 1000°, and 500' with particular emphasis on the distribution and the identification of the precipitate phases. EXPERIMENTAL WORK AND RESULTS In the present investigations of the solid solubility and of the precipitate phases in the systems tantalum-nitrogen, -oxygen, and -carbon, high-purity tantalum was reacted with high-purity gases, homogenized at 1800°c, and annealed at and quenched from 1500°, 1000,

Jan 1, 1962

By G. H. Clamer

Page Bronze Bearing Metals. By G. H. Clamer............... 162 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. Waring .. 166 The Tin-plate Industry. By D. M. BUck. Discussed by G. H. ClameR, J. W. RICHARDS............................ 168 The Aluminum Bronze Industry. By W. M. Corse............ 171 Bronzes, Bearing Metals, and Solders. By G. K. BURgess and R. W. Woodward. Discussed by G. H. Clamer, R. T. Roberts......... 175 Babbitts and Solder. By G. W. Thompson................ 184 The Cadmium Supply of the United States. By C. E. Siebenthal. Discussed by M. L. Lissberger, C. W. Hill, F. F. ColcoRd.......... 185 Solder, Its Use and Abuse. By M. L. LissbergeR............ 192 Bronze Bearing Metals G. H. ClameR,* Philadelphia, Pa.—Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early days, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 1, 1919