Search Documents

By D. H. Desy, L. C. Fincher

The magnesium-rich end of the Mg-Ti phase diagram was investigated. The liquidus, solidus, and solvus boundaries to 1 pct Ti were established. All alloys were prepared by saturating molten magnesium with titanium in a consumable titanium crucible under inert gas maintained at 230 psig. The liquidus of the Mg- Ti system was determined by analysis of dip samples taken from 700° to 1300°C under equilibrium conditions in a pressurized inert atmosphere furnace and by analysis of small ingots rapidly poured and quenched from 1400° to 1500°C. The solubility of titanium in magnesium ranged from 0.018 wt pet Ti at 700°C (0.012 wt pet at 650°C by extrapolation) to 1.035 wt pet Ti at 1500°C. The solidus for compositions ranging from 0.03 to 1.00 wt pet Ti was determined to be 650° ± 1°C by thermal analysis. The titanium solid solubility values ranged from 0.08 wt pet at 350°C to 0.19 wt pet by extrapolation to 650°C. The freezing reaction is peritectic. No intermetallic compounds were found in the system; the phase in equilibrium with molten magnesium saturated with titanium was found to be titanium with magnesium in solid solution. Solid titanium will dissolve at least 1.32 wt pct Mg. PREVIOUS investigations of the Mg-Ti system have shown considerable disagreement on the solubility of titanium in liquid magnesium. Furthermore, the solid solubility of titanium in magnesium has not been well established. Liquidus curves for previous work and for the present investigation are shown in Fig. 1. Aust and Pidgeon1 used a dip-sampling method on molten magnesium held in equilibrium with solid titanium under a protective atmosphere to determine the solubility and found that it ranged from 0.0025 wt pet Ti at 651°C to 0.015 wt pet Ti at 850°C. Eisenreich2 introduced titanium into molten magnesium by means of TiCL4 adsorbed on BaCl2. Ingots were then cast at various temperatures. Making the assumption that only the titanium dissolved in magnesium at the time of casting was soluble in H2SO4, Eisenreich determined the solubility of titanium in molten magnesium to range from 0.003 wt pet at 655°C to 0.115 wt pet at 800°C. Eisenreich also determined the solid solubility of titanium in magnesium to be 0.015 wt pet at room temperature and 0.045 wt pet at 500°C. Since the solid solubility just below the freezing temperature for the bulk of the alloy was much larger than the liquid solubility just above the freezing temperature, Eisenreich concluded that the freezing reaction was peritectic. Obinata et al.3 equilibrated molten magnesium with titanium in hermetically sealed titanium containers which were then furnace-cooled. The titanium content of the magnesium was then determined and found to range from 0.170 wt pet at 700°C to 0.85 wt pet at 1200°C. No intermetallic compound was found in the system. The Armour Research Foundation4 determined two points on the solvus by electrical resistivity methods: 0.00057 wt pet at 200°C and 0.0008 wt pet at 300°C. At higher temperatures, data were meaningless with no trends observable. The authors of this report believed that the lack of significant data at the higher temperatures was due to variations in specimen geometry, although there was no positive evidence to verify this supposition. The present investigation was undertaken to clarify the uncertainty in both the liquidus and solvus of the magnesium-rich end of the Mg-Ti system. EQUIPMENT AND MATERIALS The equipment used in this investigation, with some modifications, was essentially that used by Crosby and Fowler5 in their determination of part of the Mg-Zr phase diagram. The equipment, as modified for this work, is shown in Fig. 2. It consists of a sealed furnace chamber which can be pressurized with inert gas so that melts can be made above the boiling point of magnesium at atmospheric pressure. Melts are made by induction heating in a titanium crucible which, after diffusion of sufficient magnesium into the walls of the crucible to saturate the titanium at the sampling temperature, comprises the solid phase in equilibrium with the molten magnesium. Dip samples may be taken with the sampling tube, or the entire furnace may be tilted so that ingots may be poured into a mold in the side chamber. The principal difference from the earlier apparatus is in the thermocouple, which in the present equipment is enclosed in a protection tube and immersed directly in the melt. The tips of both the thermocouple protection tube and the sampling tube, which dip into the melt, are made of high-purity titanium. The 4 1/2-in.-long titanium tip of the sampling tube is threaded into a steel tube, O in Fig. 2, which extends through the top of the furnace. To determine whether the temperature at the tip of

Jan 1, 1969

By A. C. Butterworth

M OST operators of open-pit mines in the Lake Superior iron ore district are quite familiar with the use of fuel oil in the heavy-duty Diesel engines commonly used in truck-haulage service but some operators, including my own company, Pickands Mather, have had butane-engine trucks in service for several years, and less is known of their operation. One of the first installations of trucks for iron-ore haulage was in 1939 at a deep open-pit mine on the Cuyuna Range. These superseded standard-gauge steam haulage. Trucks then obtainable were equipped with 150-hp Diesel engines, and the speed of these units on an 8 % grade would have been so slow, considering the depth of the pit, that plans for an all-truck haul out of the pit were rejected. About this time one of the engine manufacturers brought out an auto-

Jan 1, 1948

By G. F. Olsen

ON superficial consideration a technical library might be considered a luxury to the business institution that possesses one. After all, public libraries and research institutions probably contain all the data that would be found in a private technical library, and able consultants are available both within and without a company. In all probability the technical men of a company have in their combined personal libraries sufficient information to answer most inquiries. Nevertheless, possession of such a department is of real economic benefit because of the time it saves its users, because it prevents expensive duplication of technical literature in a company, and lastly, but most important, be- cause it makes readily available a central storehouse of technical facts classified and indexed to meet the demands of the industry or industries concerned.

Jan 1, 1940

By J. Brian Eby

As is generally understood, the word geophysics means literally ?the physics of the Earth? and the science of geophysics is therefore that which treats of the study and measurements of the various physical properties of the Earth. The broad and general study of the elastic, the gravimetric. or the magnetic properties of the Earth as a whole belongs to the general science of geophysics. The detailed application of this science to rocks of shallow depth and in small areas for the purposes of ascertaining data on their character and structural attitude gave rise to the present well-known science of ?applied geophysics.? Since the discovery of enormous new quantities of oil, gas, and sulphur has been by far and wide the principal benefaction of geo-physics in the United States, this paper will refer only to geophysical methods employed in the search for these particular minerals. The application of methods and appliances originally used for geophysical research to the solution of the practical problems of finding new oil-fields, plus the counterflow or new and highly refined techniques and Instruments from the company and consulting geophysical research laboratories and into non-economic geophysical research, has provided another case of that gen-eral cycle of events which is familiar to all scientists. That this closed-circuit flow or scientific current has been tremendously important to the whole science of geophysics is probably well known to all members of this audience, but the gen-eral status of the exploratory geophysical arts as now used In the search for new oil-fields, the scales on which different methods are being used, the magnitude of the costs involved, and the far greater magnitude of the practical results achieved may not necessarily have come so directly to your attention. It is, I understand, for this reason that this paper has been sug-gested, and I shall seek to provide the information requested by using as case-illustrations those changes in the oil-reserve picture for the United States as a whole, and for the Gulf Coast, California, and Illinois Basin regions in particular, which have occurred in the period of the past 17 years, during which time oil-field discoveries have proceeded at a rate which served to build up known and readily-available (or proven) oil supplies to a reasonable figure, and have dispelled the fears of a serious oil shortage during any period for which valid fore-casts can be made. Not that geophysical-prospecting methods have alone been responsible for this transformation, but they have an indispensable and leading part in the picture of exploration and production-to which geophysics, geology, engineering, and general technical progress have jointly made contribution. So far as the United States as a whole is concerned, its total proven, probable, and possible oil reserves (discoverable and recoverable by then-known methods) were estimated at about nine billion barrels in 1920, whereas proven reserves alone are now com-puted at about 16 billion. In 1920 the driller in ?wild-cat? territory was faced with the knowledge that for every new oil-field opened by a successful well, from 20 to 100 unsuccessful wells would have to be drilled and, in some territories, that the chances for a discovery were really less than one in 100 for new drilling, in contrast to which may be cited the record for the past year in parts of Louisiana where the 67 wells drilled opened 16 new oil-fields, that is to say, where the score of hits to misses was increased to approximately one out of four.

Jan 1, 1940

By Hiland G. Batcheller

HISTORY shows that the nation which makes the most steel is the most likely to win wars. Today the course of war shows that the nations which get there first with the most steel of the right kind will be the ones to win. Not only the most steel, mind you, but the right kind. Adequate production, which was enough for victory before the days of totally mechanized warfare of 1943, must now be accompanied by still better quality as well as more effective distribution. Further, both production and distribution must be flexible enough to permit rapid shifts from one weapon to another for use in varying elements in varying geographical areas. Thus the problem of making enough steel of the right kind at the right time in the face of changing requirements dictated by experience has been and will remain highly complex. This does riot permit us to ease our restrictions on nonessential use. War is a complex business, like the job of making steel for war. Each time we solve one problem, another pops its head up. Yet we are making some progress.

Jan 1, 1943

By Hans Lundberg

IN last year's report on the progress of geophysics, the airborne magnetometer was the featured new development. At that time only a relatively small number of surveys had been made. During 1947, the airborne magnetometer was used in making many surveys and is again one of the high lights of the year in geophysics. This report is mainly concerned with geophysics as applied to the search for minerals exclusive of petroleum. In 194,5 and 1946, the use of the magnetic method reached a peak, partly because of an active period of prospecting brought on by an active mining market, particularly in Canada.

Jan 1, 1948

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of' Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C'. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement'" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.' To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

By John N. Dew, William L. Martin, `

This paper describes the results of a laboratory investigation conducted to obtain data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. Air and fuel requirements, rates of advance, com-bustion temperatures, and coke and fluid distributions are presented. The mechanism of oil recovery by in stiu combustion is discussed. Five crude oils ranging in gravity from 10.9 to 34.2"' API were prodrrced from a semiadiabatic, uncon-.solidnted sand pack by in situ combustion. Experimental conditions were varied over a wide range in order to determine the inter-relation-.ships of process variables. The mini-mum air flux requirement for self-sustained combustion was found to he less than 10 scf/hr-ft'l. The rate of advance of a self-sustained combustion zone was found to be nearly proportional to the air flux at the combustion front. The effects of presrure and injected air flux were studied in a series of experiments using a 21.2" API crude. A minimum air require-ment was observed at an air .flux of 20 scf/hr-ft'. The oil saturation con-sumed as fuel averaged 5.5 per cent of pore volume. The effect of air pressure was, found to be .small for experiments having high combustion eficiencies. This study should promote a better understanding of the problems and mechanisms involved in labora-tory investigations and field applications of the in situ combustion pro-cess. The data presented will be use- ful in the interpretation of results of field tests. When tempered with volu-metric sweep efficiencies, the data can be used in making preliminary economic appraisals of the process as applied to reservoirs containing high porosity unconsolidated media. INTRODUCTION The purpose of this work was to obtain laboratory data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. In situ combustion basically consists of (1) injecting air into a reservoir through selected input wells to create an air sweep through the reservoir, (2) igniting the crude at the injection well, and (3) propagating the combustion front through the reservoir by continued air injection. By this means, oil is swept toward producing wells in the area. The fuel for combustion is supplied by heavy residual material (coke) which has been deposited on the sand grains during distillation and cracking of the crude oil ahead of the combustion front. Recovery of petroleum by a combustion or heat wave process is not a new idea. F. A. Howard was granted a patent in 1923 on a process in which air and a combustible gas were pumped into an injection well and ignited.' Russian engineers reported on field experiments with a crude oil gasification process in 1935'. Other known early field tests include those conducted near Bar-tlesville and Ardmore, Okla., in 1942." More recently completed field tests include an inverted seven-spot by Sinclair Oil Co. in the Delaware-Childers field, Nowata County, Okla.'; a three-well and an inverted five-spot test by Magnolia Petroleum Co. in Jefferson County, Okla."."; and a test by California Research Corp. in the Irvine-Furnace field in Kentucky. The Worthington Corp. has completed a test in cooperation with the Forest Oil Corp. in Clark County, 111.l Several field tests are now in progress. Sinclair has acquired a 600-acre lease in the Humboldt-Chanute field, Allen County, Kans., and is under way with a large-scale operation. Three field tests are under way in California. The General Petroleum Corp. is conducting an inverted five-spot pattern test in the South Bel-ridge field in Kern County under a cooperative agreement with 11 other companies, including Continental Oil Co. California Research Corp. is conducting a four-well pattern test in Midway-Sunset field near Maricopa, and Richfield Oil Corp. is under way with a test in the Ojai field in Ventura County. Although the published information is valuable concerning results of field tests, little laboratory data other than that reported by Kuhn and Koch5 are available to aid in appraising the tests from a technical or economic standpoint. Engineering data needed to evaluate the process include the amount of air required per barrel of oil recovered, minimum injection rates which will support combustion, rates of advance, air required per unit volume of reservoir cleaned, amount of oil recovered, and amount of oil consumed as fuel. The present laboratory investigation was undertaken to provide these data for that portion of the reservoir swept by the combustion zone. The first phase of this investigation was exploratory in nature and was conducted at injection pressures less than 100 psig. Data were ob-

By Robert F. Mehl

THE mechanical behavior of metals and alloys is presumably conditioned by two factors; namely, the crystalline symmetry and the interatomic forces. Considerable attention has been given to the first of these factors through the recent advances in X-ray technique. It is the purpose of the present paper to call attention to the importance of the second of these factors, to point out promising methods of investigation, and to present some pertinent data. Plastic deformation takes place by slip along atomic planes.1 This slip may be inhibited in a number of ways: by the interatomic forces of cohesion which bind the atoms rigidly in a lattice structure, which in pure metals is usually of high symmetry; by lattice distortion caused by solid solution formation or by mechanical strain; by the intercrystalline boundaries where slip is restrained, probably by the non-registration of the atom planes in adjacent crystallites;2 and by the presence of small hard particles which serve to "key" the slip along the atom planes.3 In pure metals, and perhaps also in solid solutions, the atom planes of easiest slip are those exhibiting the greatest density of atomic population and the greatest interplanar distance4 and apparently can now be predicted from the analysis of the lattices. Concerning the interatomic forces, which resist this slip by holding the atoms firmly together, little is known. Most textbooks on physical metallurgy, following the work of Bottone,5 correlate the hardness of the pure metals with the atomic volume,

Jan 1, 1928

THE opening session of the Institute was held at the rooms of the American Society of Civil Engineers, No. 4 East 23d Street, Vice-President R. W. Raymond in the chair. After a short introductory address by the chairman, the following names were presented by the Council for election as members and associates of the Institute. They were unanimously elected : MEMBERS. Abbott, James W., - Lake City, Col. Abbott, J. J., Jr., - Lake City, Col. Bartlett, J. C., - Cambridge, Mass. Billings, G. H., - Boston, Mass. Blake, Frank C., - Lafayette College, Easton, Pa. Dewey, Fred. P., - Lafayette College, Easton, Pa. Douglass, Samuel T., - Ann Arbor, Mich. Emmons, S. F., - New York City. Engle, George U., - Philadelphia. Harrington, Dr. Bernard J., - Montreal, Canada. Hayden, Wm. B., - Columbus, O. Hill, Leslie C., - Capelton, Quebec, Canada. Land, W. J., - Atlanta, Ga. May, Wm. A., - Scranton, Pa. Mills, James E., - St. Louis, Mo. Moore, Charles W., - Montezuma, Ind. Page, William Byrd, - Lexington, Ky. Putnam, Douglas, Jr., - Ashland, Ky. Richards, Henry, - Dover, N. J. Roberts, Percival, Jr., - Philadelphia. Sackett, S. G., - Brooklyn, N. Y. Schley, Wm. S., - Atlanta, Ga. Setz, Gustav, - Mine La Motte, Mo. Talbutt, John H., - Lexington, Ky. Torrey, Herbert G., - U. S. Assay Office, New York City. Wernlitz, Fred. W., - Cartersville, Bartow Co., Ga. Wiestling, Geo. B., - Mont Alto, Franklin Co., Pa.

Jan 1, 1877

The opening session of the Institute was held at the rooms of the American Society of Civil Engineers, No. 4 East 23d Street, VicePresident R. W. Raymond in the chair. After a short introductory address by the chairman, the following names were presented by the Council for election as members and associates of the Institute. They were unanimously elected : MEMBERS. Abbott, James W.,.....Lake City, Col. Abbott, J. J., Jr.,...... Lake City, Col. Bartlett, J. C.,.....Cambridge, Mass. Billings, G. H.,.....Boston, Mass. Blake, Frank C.,.....Lafayette College, Easton, Pa. Dewey, Fred. P.,.....Lafayette College, Easton, Pa. Douglass, Samuel T.,. .. . Ann Arbor, Mich. Emmons, 9. F.,.....New York City. Engle, George U.,.....Philadelphia. Harrington, Dr. Bernard J.,. .. Montreal, Canada. Hayden, Wm. B.,.....Columbus, O. Hill, Leslie C.,.....Capelton, Quebec, Canada. Land, W. J.,......Atlanta, Ga. May, Wm. A.,.....Scranton, Pa. Mills, James E.,.....St. Louis, Mo. Moore, Charles W.,.... Montezuma, Ind. Page, William Byrd,.... Lexington, Ky. Putnam, Douglas, Jr.,.... Ashland, Ky. Richards, Henry,.....Dover, N. J. Boberts, Percival, Jr.,. .. . Philadelphia. Sackett, S. G.,......Brooklyn, N. Y. Schley, Wm. S.,.....Atlanta, Ga. Setz, Gustav,......Mine La Motte, Mo. Talhutt, John H.,.....Lexington, Ky. Torrey, Herbert G.,.... U. S. Assay Office, New York City. Wernlitz, Fred. W.,..., Cartersville, Bartow Co., Ga. Wiestling, Geo. B.,.....Mont Alto, Franklin Go., Pa.

By G. L. F. Powell

g samples of Cu-20 wt pct Ag alloy have been mdercooled to a maximum of 197°C by melting under a slag of commercial soda-lime glass in a vitreous silica crucible. No grain refinement of the primary copper was observed in samples undercooled to the maximum of 197°C. When the samples contained a small amount of oxygen, the copper dendrites were partially recrystallized at undercoolings greater than 97°C. In previous papers'-3 reporting the grain structure of undercooled silver and copper, it was observed that grain refinement was dependent on both undercooling and oxygen content. Grain refinement occurred in undercooled silver when the degree of undercooling exceeded the range 153" to 175"C, while in Ag-0 alloys (0.12 wt pct) fine equiaxed grains were exhibited when undercooling was greater than 50°C. Similarly, copper samples undercooled as much as 208°C displayed fan-shaped growth from a single nucleation site, while the grain structure of Cu-O alloys (0.08 wt pct) was fine and equiaxed at undercoolings larger than 150°C. Thus the presence of oxygen greatly reduced the undercooling at which grain refinement occurred. It was also observed that the change in grain size resulted from recrystallization and was not due to an enhanced nucleation rate in the liquid-solid transformation. It is possible that the influence of oxygen on recrystallization is due primarily to its presence as a solute element. walker4,' reported that, although a grain size change did not occur in pure nickel until the undercooling exceeded 150°C, small grains were observed in samples of Ni-Cu alloy solidified at small and large degrees of undercooling. Jackson et al.6 suggested that the fine grained structure of the Ni-Cu alloy resulted from the melting off of dendrite arms during recalescence. This remelting process may occur in alloys as a result of segregation during freezing which causes a variation in liquidus temperature from point to point within a dendrite. It was therefore decided to undercool copper with a metallic alloying element to ascertain whether the presence of a metallic solute would have a similar effect to oxygen in inducing grain refinement. A Cu-Ag alloy was chosen, since both metals had been shown to behave similarly on undercooling. The alloy Cu-20 wt pct Ag was selected since the eutectic constituent outlines the initial growth form of the primary copper, so that the as-frozen grain structure is not obscured if subsequent recrystallization occurs. This paper describes the results of undercooling experiments carried out with Cu-20 pct Ag samples undercooled to a maximum of 197°C and the effect of oxygen content on the grain structure of the undercooled samples. EXPERIMENTAL Melting was carried out in a small cylindrical resistance furnace using "fine" silver granulate and oxygen-free high conductivity copper. The procedure adopted was to melt the required quantity of silver in air in a clean vitreous silica crucible for approximately 15 min, freeze, and add granulated commercial soda-lime glass to form a complete surface slag cover, after which the sample was melted and frozen several times to reduce the oxygen content. The glass slag cover was approximately 3 in. thick. Pieces of copper (=50 g) were added to the crucible until the required quantity to make 350-g samples of alloy had been charged. Each piece was added quickly to the crucible which was held at a temperature slightly above the melting point of silver. The piece was quickly pushed beneath the glass to minimize oxidation and any oxide coating usually decomposed before the piece had settled down into the silver. After the full quantity of copper had been added, the melt was stirred with a silica rod to hasten homogenization and a Pt/Pt 13 pct Rh thermocouple enclosed in a vitreous silica sheath inserted for temperature measurement. Heating and cooling curves were recorded on a potentiometric chart recorder fitted with a zero suppression unit. The milli-voltage range of the recorder was adjusted so that temperatures could be read to 1°C. Heating and cooling curves were taken every hour until three consecutive readings gave the same solidus-liquidus range, consistent with the solidus-liquidus range for this alloy composition by reference to Hansen and Anderko.7 Metallographic examination of samples frozen at this stage, failed to show any variation in composition from bottom to top of the ingot. Consequently, it was considered that the melt was homogeneous at this stage and undercooling experiments were then car-

Jan 1, 1970

By John Griffen

OF the western European countries, only England has made any extensive use of equipment developed initially by the coal preparation industry of the United States. About 20 years ago, the Chance sand flotation process for cleaning coal was introduced in England, and it has had a fairly wide adoption, particularly in the South Wales coal fields. In recent years, particularly since 1946, a considerable number of Denver flotation cells have been installed throughout the English coal fields for the cleaning of slurry. Until the advent of the Denver cells, the flotation of coal slurries in Western Europe had been done largely with the Mineral Separations cell or its modifications. Kleinbentik of Dutch State Mines had developed a cylindrical cell used in Holland and occasionally in Belgium and France. In England, the establishment of the National Coal Board to control the planning and operation of all coal production has retarded somewhat modernization of properties. A considerable period of study was required before definite long-range plans could be formulated. It was soon recognized that stopgap measures were needed in many cases to bridge the period until final plans could be developed and consummated. One of the stopgap problems in coal preparation was providing plants of small and medium capacity that could be used for a few years at one site and yet could be moved economically to another site so as to reduce depreciation charges per year and per ton. Such plants are being installed but the most satisfactory answer probably has not yet been found. One such installation uses a Norton Baum jig to wash 6 in. to 0. The equipment is in a steel structure rather than in a reinforced concrete frame with brick curtain walls, which is the normal structure for permanent plants. Since England has between 700 and 800 preparation plants for an output of 200 million tons per year, one of the long-range objectives is a consolidation of mine output which will require fewer coal

Jan 1, 1952

By F. H. Spedding

From thermal, metallographic, X-ray, dilatometric, and electrical resistance data a Phase diagram is proposed for the La-C system. TWO compounds are formed, body-centered-cubic Laz C, having a large range of solid solubility, and body -centered-tetrago-nal Lac2 . The former melts incongruently at 1415°C, and at 25OC it has an electrical resistivity about two and one-half times that of bure lanthanum. The latter melts congruently at 2356°C and at room temperature has an electrical resistivity about equal to that of bure lanthanum. The addition of carbon to La lowers the melting Point of La about 115' C, raises the higher (B-Y) transfomzation about 10" C and appears to have no effect on the lower ( a-0) transformation. The addition of carbon appears to lower the oxygen content in the metal and improve the machinability; however, the tendency to oxidize is increased. Two eutectics are formed in the system. The first occurs at 2.2 pct C and melts at 806" C, while the second occurs between Lac2 and C with a melting point of2271"C. PETTERSSON,~ in 1895, was the first to prepare lanthanum dicarbide by heating the oxide with carbon in an electric furnace. He showed that this yellow, crystalline but brittle carbide had a formula corresponding to LaCz and that it reacted with water with the evolution of hydrogen and hydrocarbons and the formation of the hydrated oxide. Von Stackelberg's investigation of the crystal structure of the MCz carbides showed that the lanthanum dicarbide is of the tetragonal calcium dicarbide-type structure. He found the lattice parameters were a = 3.92 and c = 6.56.* Bredig,' using X-ray methods, showed that the room-temperature form of lanthanum dicarbide is stable up to 1750 °C and that above this temperature it transformsoto a face-centered-cubic structure, a = 6.0 ± O.lA, probably of the pyrite, FeSzstruc- typ? The reported discovery of two new cerium carbides, suggested that a corresponding face-centered-cubic lanthanum monocarbide and a body-centered-cubic lanthanum sesquicarbide might exist. This paper describes work on the lanthanum-carbon system which is part of a study of the rare earth metals and their alloys now in progress in this laboratory. EXPERIMENTAL PROCEDURE Source of Materials—The lanthanum metal was prepared at the Ames Laboratory by metal1o;hermic reduction of the fluoride with calcium metal. The results of spectrographic and chemical analysis indicated the presence of 0.01 pct Y, Al, Cu, Fe, and Si; 0.02 pct Ca and Mg; 230 ppm C; and 115 ppm N. The carbon used was of two types: 1) "National Special Graphite Spectroscopic Electrodes," and

Jan 1, 1960

By RICHARD MAIZE

IN this critical period of our history, the coal industry of the nation, faced with many obstacles, performed its work safely during the first ten months of 1943. Thousands of the younger mine workers were inducted into the armed forces of our country and in many instances their jobs have been filled by others without much if any experience and training. This situation alone would seem to be sufficient to interfere with the safe and orderly operation of the industry but the Government's demand for a substantial increase in coal tonnage over that produced in normal times introduced a hazard which always accompanies speed, regardless of the skill of the worker.

Jan 1, 1944

Institute of Metals Division PAUL D MERICA, Chairman ZAY JEFFRIES, Vice-chairman W M CORSE. Secretary General Committee ROBERT J ANDERSON H C JENNISON L W SPRING WILLIAM K FRANK DAVID LEVINGER R L SUHL J R FREEMAN, JR. PAUL McKINNEY R F WOOD STANISLAUS SKOWRONSKI

Jan 1, 1923

By H. J. Wasson

WITH the close of 1932 and the third year of the depression, the activity of oil production presents, amidst the general wreckage and chaos of industrial society, a somewhat unique picture of rationalized economic effort. East Texas still dominates the contemporary horizon, but it has become, at least for the time being, a definitely known factor. With its 9500 wells it is approximately 90 per cent drilled up. So long as production control obtains, it is merely one important factor of the national oil reserve. Each succeeding month of stabilized production tends to lull the industry's fears and the menace, both actual and psychological, of this giant field becomes ever more remote.

Jan 1, 1933

By RUSSELL C. FLEMING

GILSONITE is a brilliant black, tarry-like bitumen, classed technically with glance pitch and graharnite as an asphaltite. As found it is brittle, breaking much like ice, and has a conchoidal fracture. Purest forms are used in the manufacture of paints, varnishes, electrical irisulatiorl, and inks for rotogravure; molded articles such as switch handles, telephone mouthpieces, and but- tons are made from the intermediate grades, and the poorer grades are used for the saturation of felt. According to the U. S. Bureau of Mines figures, production grew from about 4000 tons mined in 1904 to 55,000 tons in 1929. This asphaltic substance is found only in the Uintah basin in northeastern Utah, in veins over a wide area. Veins in the vicinity of Fort nuchesne were first discovered about 18G2, on what was then the Uintah Indian reservation, and the vein matter was originally called Uintaite because of that fact, In the early days, S. H. Gilson. of Salt Lake City, was so persistent and zealous in his efforts to develop the deposits and find a market that the name gilsonite was given to the material. Later, the wider and more renowned wins near Wayson and Dragon, in extreme eastern Utah, became the main supply.

Jan 1, 1932

By A. C. Milner

In a gold standard world which possesses insufficient metal to meet the every-day needs of all, confidence becomes the vital factor, the very foundation upon which the machinery for the expansion of gold into currency, and credit, rests. The gold supply, affected by many influences, moves constantly from one point to another, but not always to that point where it is most needed. In the period 1928-1930, the combined gold holdings of the United States and France increased $1,370,936,-000, and this with new gold adding only $600,000,000 to the monetary gold stock.Theref ore, the gold stocks of other countries must have been depleted during the period by $770,936,000. This uncontrolled shifting throws the delicately adjusted instrumentalities of both credit and commerce out of equilibrium. If a given nation's gold stock shifts so as to bring it substantially below the legal reserve ratio set up against it for currency issues, the effect can easily extend to the currency issues and banking credit volume of one or more nations which may have based their gold exchange standards upon the gold stock of such nation. Thus the substitution of paper based on gold in place of the actual gold is an inflation of the currency, which carries through into an uncontrolled pyramiding upon the entire machinery of credit based on gold. In 1929 Europe, South America, Africa and Asia had overissued currency based on gold. America, Oceanica and Japan, which have not overissued their gold currencies, would in normal times require their entire present gold stocks and, as Continental Asia is largely upon a silver credit basis, from a domestic standpoint, it would appear that the gold problem is not so much one of maldistribution, as it is one of inadequate supply. It would appear that some method of increasing greatly the velocity of gold, within the safe reserve point, should be devised, or that silver, of which estimates indicate that 7,000,000,000 oz. are available for

Jan 1, 1931

By N. A. Gokcen, John Chipman

SILICON is the most commonly used deoxidizer and an important alloying element in steelmak-ing; hence a detailed study of this element in liquid iron containing oxygen is of considerable interest. The equilibrium between silicon and oxygen in liquid iron has been studied by a number of investigators but generally with inconclusive or incomplete results. The variation of the activity coefficients of silicon and oxygen with composition is entirely unknown. Published investigations deal with the reaction of dissolved oxygen with silicon in liquid iron and the results are expressed in terms of a deoxidation product. For consistency and convenience in comparison of the published information, the deoxidation product as referred to the following reaction is expressed in terms of the percentage by weight of silicon and oxygen in the melt in equilibrium with solid silica: SiO (s) = Si + 2 O; K'l = [% Si] [% 012 [I] Theoretical attempts to calculate the deoxidation constant for silicon in liquid iron from the free energies of various reactions yielded results which were invariably lower than the experimental values. Thus, the deoxidation "constants" calculated by McCance,1,2 Feild,3 Schenck, and Chipman were of the order of 10, which is below the experimental values by a factor of more than 10. Experiments of Herty and coworkers" in the laboratory and steel plant resulted in an average deoxidation constant of 0.82x10 ' at about 1600°C. The technique employed in their investigation was crude and the reported temperature was quite uncertain. The concentration of silicon was obtained by subtracting silicon in the inclusions from the total. Since at least some of the inclusions resulting from chilling must represent a fraction of the silicon in solution at high temperatures, such a subtraction is not justifiable. Results of Schenck4 for K'1 from acid open-hearth plant data yielded a value of 2.8x10-5, which was later revised as 1.24x10 at 1600°C. Similarly Schenck and Bruggemann7 obtained 1.76x10-5 at 1600OC. The discrepancies and errors involved in the acid open-hearth plant data as compared with the results of more reliable laboratory techniques were attributed by these authors to the lack of equilibrium and the impurities in liquid metal and slag, and are sufficiently discussed elsewhere." Korber and Oelsen" investigated the relation between dissolved oxygen and silicon in liquid iron covered with silica-saturated slags containing varying concentrations of MnO and FeO. The deoxidation products obtained by their method scatter considerably, and their chosen average values of 1.34x10, 3.6x10-5, and 10.6x10-5 1550°, 1600°, and 1650°C, respectively, represent the best experimental results which were available until quite recently. Darken's10 plant data from a steel bath agree approximately with their data at 1575° to 1625°C. Zapffe and Sims" investigated the reaction of H2O and H2 with liquid iron containing less than 1 pct Si and obtained deoxidation products varying by a factor of more than 20. Inadequate gas-metal contact and lack of stirring in the metal bath should require a longer period of time than the 1 to 5.5 hr which they allowed for the attainment of equilibrium. Furthermore, their oxygen analyses were incomplete and irregular and confined to a few unsatisfactory preliminary samples. Their results did indeed indicate that the activity coefficient of oxygen is decreased by the presence of silicon, although they made no such simple statement. They chose to attempt to account for their anomalous data by the unlikely hypothesis that SiO is dissolved in the melt. Hilty and Crafts" investigated the reaction of liquid iron with acid slags under an atmosphere of argon, making careful determinations of silicon and oxygen contents at several temperatures. Despite erroneous interpretation of the data at very low silicon concentrations, their data represent the most dependable information on this equilibrium that has been published. In the range 0.1 to 1.0 pct Si, their data yield the following values for the deoxidation product: 1.6x10-5, 3.0x10- ', and 5.3x10 at 1550°, 1600°, and 1650°C, respectively. The purpose of the work described herein was to study the equilibrium represented by eq 1 as well as the following reactions, all in the presence of solid silica: SiO2 (s) + 2H2 (g) = Si + 2H2O (g);

Jan 1, 1953