Search Documents

By R. G. Ward, John Henderson. R. G. Hudson, G. Derge

Densities of melts of the iron oxide-silica system in contact with solid iron have been measured by the maximum hubble pressure method in the composition range O to 37 wt pct SiOz and the temperature range 1255 to 1410C. The constitution of the melts is discussed and it is postulated that the structure changes from a dislribution of iron ions in an oxygen ion network at pure "FeO" to a distribution. of iron ions in a network of silicate tetrahedra at the orthosilicate composition. JOHN HENDERSON, Junior Member AIME, was formerly with the Metals Research Loborotory, Carnegie Institute of Technology, Pittsburgh, Pa., on leave from Broken Hill Proprietary Co., Ltd., Research Division, Shortland, Australia. R. G. HUDSON, formerly with Metals Research Laboratory, is now with the John Jay Hopkins Loborotory for Pure and Applied Science, General Atomic Division, General Dynamics Corp., LaJolla, Calif. R. G. WARD, was formerly with the Department of Metal lurgical Engineering, Carnegie lnstitute of Technology, while on leave from the Department of Metallurgy, University of Sheffield, England. G. DERGE, Member AIME, is Jones and Laughlin Professor of Metallurgical Engineering, Carnegie lnstitute of Technology. Manuscript submitted January 19, 1961. ISD The system iron oxide-silica is an important one metallurgically because it forms the basis of several complex slag systems in use for industrial smelting and refining processes. In recent years considerable work has been done on liquids of this system but there are still many points of difference among workers using different experimental techniques and theoretical approaches. Phase equilibria/"3 activity,4-6 electrical conductivity,' current efficiency,' transference number,8 viscosity,9 surface tension,'' and density" measurements have all contributed to an understanding of the problem. Measurement of density is one procedure which is directly indicative of liquid structure since any deviation from ideality must be a result of structural interactions. Liquids of the iron oxide-silica system are of special interest because this is one of the few metal oxide-silica systems on which measurements can be carried out conveniently over the entire composition range from pure oxide to silica saturation. This includes the range of high basicity which has received relatively little attention in other systems. Although one investigation of density in this system has previously been undertaken," the results seem of sufficient importance to warrant the independent redeter-mination reported here.

Jan 1, 1962

By Wilfred P. Sykes

AT intervals in the course of history an event occurs which, though scarcely heeded at the moment, marks in retrospect the beginning of a new era in some one field of human activity. Such a happening is perhaps more readily spotted in the field of technology than in other realms of human endeavor. Here the span of years is relatively short and the records have been kept with some degree of precision. In the current scene of our social and economic drama the art and science of metallurgy is playing a major role. Off stage will be found the metallurgist in one guise or another aiding, he trusts, in the development of processes and products which will contribute to the happiness of his fellow men. The results of his efforts appear in the form of metallic substances known as alloys built up from any two or more of the wide variety of metals which have been extracted from the mineral deposits in the earth's crust. An alloy by virtue of its inherent physical properties may seem ideally suited for human use in a special way but until this material can be produced economically it will fail to attain a place of prominence as an article of commerce. In fact many commercial alloys are being continually replaced by new or modified compositions better suited to meet the increasingly severe demands of industrial service.

Jan 1, 1939

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945

By Robert S. Dewey

More wells were drilled in West Texas† during 1944 than in any year since 1941. As compared with 1943, there was an 82.5 per cent increase in the total number of completed wells. The 1646 wells required an estimated 140,715 days to complete for a total of 7,632,249 ft. An average of 85 completion days was required to drill to an average of 4630 ft. This depth is approximately 100 ft. greater than that of the previous year. It is estimated that $100,000,000 was invested in drilled wells. As of Dec. 31, 1944, there were 270 field and 91 wildcat wells being drilled. While an identical number of wells were drilling Dec. 31, 1943, the proportion of wildcats increased in 1944 from 19.7 to 25.2 per cent. During 1944, oil wells were completed in 103 of the 164 fields in West Texas. Of the 1361 oil wells, 385 were in Slaughter, 116 in Fullerton, 63 in North Cowden, 62 in Fuhrman-Mascho, 59 in Wasson, 52 in Westbrook and 47 in North Ward. Approximately 22 per cent of the wildcat drilling was to pre-Permian formations. Despite the increasing proportion of wildcat wells drilled, the wildcat discovery rate has declined since the year 1942. AS compared with 1943, the number of wildcat wells drilled increased from 11.7 to 12.7 per cent and the footage in wildcat exploration increased from 13.3 to 13.8 per cent of the total. The monthly production of crude continued to increase to a peak of 15,336,000 bbl. in October 1944. As compared with a similar peak production in October 1943, there was a 37.3 per cent increase. The yearly production increased from 98,165,-ooo bbl. in 1943 to 159,943,000 bbl. in 1944, an increase of 62.8 per cent. Based upon an assumed average price of $1.00 per barrel and less 1/8 royalty, the gross return to the producer amounts to $140, 000,000. From 1943 to 1944, the average number of producing wells increased 6 per cent while the average daily production per well increased 53.1 per cent. The average daily production per well increased from 17.5 bbl. in 1943 to 26.8 bbl. in 1944. The proportion of flowing wells decreased from 50.5 per cent in January to 49.1 per cent in December 1944. Drilling With the continued shortage of labor and materials, drilling costs have risen sharply. Just how much is difficult to ascertain. Owing to competition for available drilling rigs, contractors are reluctant to assume drilling risks. In consequence, some contracts are let on a cost plus basis, or day work below some specified depth with the operator furnishing part of the consumable materials, such as mud and drilling bits. Contractors are having difficulty in maintaining full and effective drilling crews with insufficient and inexperienced labor. Service companies have inadequate labor and equipment to meet their appointments promptly. Pipe Lines The Gulf Pipe Line Co. increased the capacity of its 10-in. main line by filling in gaps amounting to 75 miles on the loops between Judkins and Weatherford, Texas.

Jan 1, 1945

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By Charles P. Williams

THE successful production of zinc white or oxide on a commercial scale in this country dates from the issue of the patent of Samuel Wetherill, for the preparation of the material (November, 1855), and

Jan 1, 1877

By Charles P. Williams

The successful production of zinc white or oxide on a commercial scale in this country dates from the issue of the patent of Samuel Wetherill, for the preparation of the material (November, 1855), and

By E. J. Whittenberger

OVER the past two decades, the Cr-Ni stainless steels, popularly termed 18-8 steels, have been used in ever increasing amounts in the aircraft, automotive, chemical, transportation, and building industries.' The contribution of nickel to these steels is associated with its strong austenite forming tendencies which assure good hot and cold forming characteristics, and with its beneficial influence upon corrosion resistance, especially in oxidizing acids. The adjustment of the chromium and nickel contents has been used advantageously in controlling the rollability and the response of the mechanical properties of these steels to cold reduction. With the advent of the jet age and the government stockpiling of nickel, considerable emphasis has been placed upon the development of satisfactory low nickel or nickel-free substitute austenitic stainless steels, especially for nonmilitary applications.2 Fer-ritic 17 pct Cr (AISI Type 430) stainless steel has been effectively substituted for the austenitic grades in applications with mildly corrosive exposure. However, the limited formability and ferromagnetic behavior of this grade do not permit its satisfactory use for many applications. To achieve better formability in a nenmagnetic steel and conserve nickel, a number of low nickel substitute austenitic grades of stainless steel have been developed in recent years. In most of these steels, manganese and nitrogen have been substituted for a portion of the nickel content, for example, 17 pct Cr-4 pct Ni-6 pct Mn (AISI Type 201), 18 pct Cr-5 pct Ni-8 pct Mn (AISI Type 202), and 16 pct Cr-1 pct Ni-17 pct Mn, all of which contain approximately 0.15 pct N.1 The precipitation of ferrite when large ingots of these Cr-Ni-Mn-N steels are heated to temperatures high enough for conversion to slabs on conventional universal slabbing mills has seriously affected the hot workability of these steels. This has been especially true in the case of the 16 pct Cr-1 pct Ni-17 pct Mn (sometimes referred to as 15 pct Cr-1 pct Ni-15 pct Mn) composition." Because it is possible that little, if any, nickel will be available for nonmilitary stainless steel applications in the event of a national emergency, a need has existed for a nickel-free austenitic stainless steel containing hot and cold forming characteristics similar to 18-8 steels and corrosion resistance at least comparable to the 17 pct Cr ferritic steel. The aforementioned deleterious effect of ferrite upon the hot working characteristics of the 16 pct Cr-1 pct Ni-17 pct Mn, steel indicates the importance of establishing the austenite-austenite plus ferrite phase boundaries as the first step in the development of nickel-free or low nickel substitute steels. This paper presents the data collected in an elevated temperature constitutional study of the Cr-Ni-Mn-N system at the South Works of the United States Steel Corp. Experimental Procedure The 300 compositions used in the investigation were melted in a 26 Ib induction furnace and cast in 3 14 in. diam by 18 in tall hot-tcpped ingot mo1ds.

Jan 1, 1958

By P. P. Gregory

Natural petroleum gas occurring in the oil-bearing reservoirs is found to exist either as free gas associated with the oil and/or in solution in the oil. In some virgin fields practically no free gas is encountered under the reservoir conditions of pressure and temperature, although in other fields a considerable section of the "pay" horizon is occupied by free gas. In other words, a given oil field may or may not have a gas cap before the exploitation takes place. However, when the reservoir pressure is reduced to a point below the critical saturation pressure by withdrawals of fluids from the producing formation, the gas dissolved in the oil inevitably begins to come out of solution and becomes free gas. Under the controlled methods of production and drilling, a portion of this gas is produced with the oil to the surface and a portion of it remains within the reservoir to accumulate at higher structural levels toward which it migrates by virtue of its low specific gravity. The rate of growth of a gas cap in a given structure depends primarily upon the rate of decline in the reservoir pressure. If the rate of pressure decline is rapid, the gas cap likewise will grow rapidly. On the other hand, shrinkage in the gas-cap area was noted in some fields in which reservoir pressures wereincreasing. Determination of Gas-oil Contact and Thickness of Gas Cap The gas-oil contact can be conveniently located in the process of drilling a well and by electrical logging. However, very little can be found in the petroleum literature concerning methods of predetermining gas-oil contacts in producing reservoirs. Therefore, the writer feels justified in describing briefly a simple, workable, and inexpensive method of determining gas-oil contacts and outlining the limits of gas-cap areas in a field where such knowledge may be essential for efficient production and development operations. The method involves the determination of the following data: (I) Structural data, such as the depth or elevation of the top' of "pay" horizon; (2) reservoir pressures; (3) tubing and casing pressures at the well head; (4) static oil-pressure gradient; (5) static gas-pressure gradient. These data can be secured with a minimum of expense, inasmuch as the

Jan 1, 1938

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By AIME AIME

EVEN though most of the program of the joint meeting at Easton, Pa., on Oct. 30 to Nov. 1. was devoted to the interests of combustion engineers rather than to coal-mining engineers, nevertheless the A.I.M.E. Coal Division was well represented, with 83, or close to one third of those in attendance giving this as their affiliation. The fuels division of the American Society of Mechanical Engineers had 108 representatives, and an equal number reported no society affiliation. Added to the men's total registration was that of some twenty ladies so the total attendance was in the neighborhood of 325, exceeding that of the last two joint meetings, at Birmingham and Columbus, and equaling the 1938 crowd at Chicago.

Jan 1, 1941

By David, Levinger

THESE observations of the metal-working industries of Europe are based on a three months' tour of eight countries of Europe, in which 75 industrial establishments were visited in England, France, Germany, Belgium, Holland, Italy, Austria and Switzerland during the summer of 1927. Since the Western Electric Co. is a large consumer of copper and brass, these industries were of particular interest and differences in practices were of keen interest to us.

Jan 1, 1928

By Robert Livermore

It has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining CO. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining CO. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently fay from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, by means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities of ore, and made development in certain

Jan 1, 1915

By Robert Livermore

IT has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored, or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the .underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining Co. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining Co. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently far from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, y means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities -of-ore, -and- made development- in certain

Jan 7, 1914

By H. H. Alexander

IN the early part of the last century textile fabric was used for the filtration of products of combustion and lampblack was obtained by passing smoke through a series of canvas bags. Natural draft was, used to draw and force the smoke through the bags. About 1850 bag filtration was used for collecting zinc oxide. Around 1876 it was introduced for collecting the fume from lead-ore hearth smelting in. Missouri. Shortly afterward it was used, first at Portland, Me., and later at Canon City, Colo., for the collection and production of zinc-lead pigment in treating mixed zinc-lead sulphides. In 1890 the Globe Smelting & Refining Co., at Denver, Colo., installed a bag house containing 1,458 bags for the recovery of fume from silver-lead blast furnaces. This installation was too small to handle all of the gases and was increased to approximately 2,300 bags. . In 1900 the number of bags was again increased, making a total of approximately 2,800: The usual difficulties incident to new installations were encountered, but they were gradually overcome and the bag house became accepted as standard practice for this class of smelting. As all of the bag houses built since have followed the general lines of the Globe installation, a short description may be of interest. The general construction of the Globe bag house is shown in Figs. 1, 2, and 3. The building is 149 ft. 8 in. long by 67 ft. 4 in. wide and 40 ft. 2 in. high from the basement floor to the eaves of the roof, having brick walls 26 in. thick from the foundation up to the thimble floor, from there an 18-in. wall for 16 ft. and a 13-in. wall from this point to the top, a distance of 14 ft. 2 in. Additional stiffening is given to the walls above the basement by pilasters located every 16 ft. The end-wall construction is similar to that of the side walls with the exception of the spacing of the pilasters, which is somewhat greater. The roof is made of corrugated iron laid on 1-in. boards and supported by a timber frame work spaced 16 ft. apart resting on the basement partition walls. On top is a louver running the

Jan 8, 1914

By R. E. Wade

The Butte, Anaconda & Pacific electrification is of peculiar interest, in an incidental way, to the entire mining fraternity, and especially the engineering branch, not only in this great Northwest country but throughout the entire Western mining country, which is rich in minerals and water power. It is probably fair to say that the prime object of mining and smelting engineering is to reduce the cost of production, and in the case in hand the relative location of mines and smelter brings the cost of transportation of ore to the front. While some might assign this item to the railway people, it is inseparably a part and parcel of the general scheme of the production of metal from the ore. In considering the electrification of the B., A. & P. railway the mining and smelting engineer, above all, wants to know what saving will be effected by the change in motive power. Unfortunately the new power has been in use during a very limited period and on the Smelter Hill section of the road only, and no reliable data, from actual service conditions, can be obtained until the entire electrified section has been in service for a reasonable length of time. Any remarks on this subject at the present time, therefore, must of necessity be general in nature and more or less descriptive. The railway, electrical and mining worlds and the country in general are indebted to the B., A. & P. railway for the pioneer work it is now doing, as it undoubtedly marks the beginning of the electrification, within the comparatively near future, of all transcontinental roads between the Missouri river and the Pacific coast. Together with this goes the development of an untold wealth in water power and all natural resources within the same territory. For the first time in the history of electric railway work, in this country, direct current at a potential of 2,400 volts is being used. With this potential there is a great saving in transmission of energy to the locomotives and there are only two substations, one at either end and 26 miles apart, for supplying the power for the movement of trains of heavy tonnage over the main line and for switching movements at terminal and intermediate yards, and comparatively little feeder copper is required.

Jan 1, 1914

By L. S. Panyity

The inception of this paper may be traced directly to the various discussions of another paper by the writer1 wherein certain indefinite beliefs and opinions were emphasized as to the relative importance of total sand porosity and the actual size of the openings between the grains. Since publication of that paper it has been possible to study various methods of sand analyses and results that have been obtained under different conditions and actual operations in the field. The purpose of this paper is to indicate the value of screen analysis, especially in areas where repressuring by means of water-flood, air or gas is being used in the partly depleted fields. Sand samples have been analyzed for porosity, saturation and grain size. They are mainly from the Bradford water-flood area, where a great reliance has been put upon such analyses, and where many data are available, A few sand studies are included from fields other than the water-flood area, in order to indicate the possibilities of screen analysis in any field. Examples of various conditions are given in Figs. 1 to 7, which show the porosity, saturation and grain-size analyses of submitted cores or drill cuttings. The generally accepted methods of delineating such sand studies on cross-section paper, known as "core charts" has been employed; with the exception that a method of representing grain size has been evolved which is believed to be the best adapted for this purpose. It differs from the block diagrams generally used, in the employment of a linear section. Percentage of grain-size is represented by the subdivision of a given distance, where the total length represents the whole sample of rock chunk, while the subdivisions indicate the percentages of grains of the different sizes that will pass through the various sieves, through which the samples of crushed sand are sorted to determine the size and amount of the components that make up the aggregate. Thus, on Fig. 1, under the heading of Grain Size, the first samples are composed of grains of the following sizes: 16 per cent. through 120-mesh sieve; 33 per cent. through 150-mesh; 25 per cent. through 180-mesh; 26 per cent, through 200 mesh; a total of 100 per cent. A minus sign is placed before

Jan 1, 1931

J. J. MCLELLAN, Webb City, Mo.-The Media mill, at the time it was built, was the largest mill that had been designed in the Joplin district. It was put up in a hurry, to take advantage of the high prices for zinc ore in 1915, by the owners of an adjacent plant, which had been very profitable. They owned a compound Corliss engine, and to take advantage of a single-unit drive it was necessary to build the mill in the form chosen, which involved making the hopper feed directly through the breakers and rolls, the undersize from the screen passing at once to the jigs, the oversize going through the rolls and returning to the original trommels. The mill was built in fairly good proportion; crushing was done by jaw breakers, Webb City pattern,' and three sets of 42-in. (106.7-cm.) Cornish rolls for reducing the oversize. The jigs were larger than the usual practice. The roughers were two six-cell jigs, with 42 by 48-in. cells. The cleaner jig was the largest ever constructed in the district up to that time, having seven 36 by 48-in. cells, for treating the rougher jigs. There was also a chat rougher. "Smittem," as used in our district, is the partly concentrated product from the rougher, which is finished on the cleaner jigs. "Chats" are the middlings proper, that is, they are the grains of chert with included particles of sulphide; the very low-grade smittem is sometimes included among the chats. When drawing chats from a jig, we also draw about ten times greater quantity of barren chert in order to insure complete recovery of mineral. This mixture of middlings and tailings is taken to a set of 30-in. rolls, the crushed product then going to a chat rougher, a comparatively small jig, with 26 by 36-in. cells. The principal departure of the Media mill from the usual practice was to build a hopper sufficiently high to give gravity feed to the jigs, without using elevators. The sludge plant, for table treatment of sand and slime, also contained several innovations in the manner of distributing the feed. The tables were arranged in two rows and the feed ran around the outside in a launder having two or three cone classifiers

Jan 1, 1918