Search Documents

By H. Kenworthy, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2 with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite- type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore.

Jan 1, 1949

By H. L. Bridgman

The correct sampling of ores is a subject of far greater importance than is usually conceded to it. Of the little which has been published on this subject, the recent paper by Mr. Glenn, with the accompanying discussion by Dr. Raymond (Trans., xx., 155), is the latest and best, and well worthy the careful perusal of all interested in accurate sampling, whether by hand or by machine. It is doubtless true that thorough hand-sampling gives as good average results as can be obtained; but all hand-sampling is subject to the possible incompetency, carelessness, or dishonesty of the workmen employed. It is, moreover, tedious and expensive, requires large space, and usually entails considerable delay, both in unloading and in sampling. For these and other reasons, machine-sampling is now regarded with more favor than ever before. So-called machine-sampling may be accomplished in two radically different ways: 1. Part of the stream of material is taken for the whole time. 2. The whole stream of material is taken for part of the time. Under the first case the stream, as it issrles from the deliveryspout of the crusher, is cut continuously in any given proportion, such as one-tenth, one-fourth, or one-half, by some fixed apparatus, which, as it contains no moving parts, is strictly speaking not a machine at all, but may be termed an appliance. The principle under which these appliances operate is now pretty generally conceded to be wrong, becanse of the practical impossibility of' cutting such a

Jan 1, 1892

By Joshua I. Tracey, Mackenzie Gordon

THE bauxite deposits in central Arkansas were formed by weather¬ing, in early Eocene time, of fresh or kaolinized nepheline syenite above the water table in a subtropical climate of fairly continuous moisture. Four types are recognized: (1) residual bauxite deposits on kaolinized nepheline syenite, (2) residual deposits on kaolin and bauxite detritus, (3) alluvial deposits of sorted pebbles and pisolites of early Wilcox age, and (4) rubble deposits of later Wilcox age. All were invaded by kaolin and siderite during subsequent burial by Eocene sediments. PART I-FIELD RELATIONS OF THE DEPOSITS The Arkansas bauxite region for years has produced about 95 pct of the domestic supply of bauxite of the United States and it contains today reserves of more than 40 million tons-nine tenths of the known domestic reserves. During World War II, the Arkansas bauxite deposits were explored jointly by the U. S. Geological Survey and the U. S. Bureau of Mines. Some 6000 holes were drilled by rotary rigs under contract to the Federal Govern¬ment, which resulted in the discovery and delimiting of approximately 20 million tons of ore in place. Detailed study of the many sections cored through the bauxite, of data from a much greater number of drill holes made available by all the operating companies, and of the extensive mine faces exposed in the strip pits, has yielded valuable geologic information about the origin of the deposits. It is now possible to piece together a paleotopographic picture of the deposits and the now-buried land surface on which they formed. The bauxite region in the center of Arkansas (Fig 1) contains two producing districts: one in Pulaski County, just south of Little Rock, and the other in Saline County, about 15 miles to the southwest. The deposits in both districts are associated with hills of nepheline syenite, bosses of a large batho¬lith that was intruded into Paleozoic rocks and later buried beneath coastal plain sediments deposited during Cenozoic time. The folded Paleozoic rocks are exposed in the northwest half of the state and are covered in the southeast half by the nearly flat-lying coastal plain sediments. The older rocks were intruded by nepheline syenite, probably in Late Cretaceous time, and sub¬sequently were eroded so as to expose the top of the batholith. In Paleocene time, marine limestone and laminated black silty clay of the Midway group were deposited in an advancing sea, and covered all but the most elevated parts of the batholith. Erosion of the islands of nepheline

Jan 1, 1952

By Henry Rawdon

THE structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i.e., manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the inclosures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in "pure" metals in general (etching pits).

Jan 9, 1917

MINING METHODS. JAY A. CARPENTER, Chairman P. B. BUCKY, Vice-Chairman CLYDE E. WEED, Vice-Chairman ROY A. HARDY, Secretary Alluvial Mining CLINTON BERNARD O. B. PERRY NORMAN CLEAVELAND C. M. ROMANOWITZ R. B. EARL! NO J. B. STAPLER BENERE H. GRANT CHARLES THURMAN Open-Cut Mining Iron A. D. CHISHOLM P. G. HARRISON G. E. DIEHL EARL E. RUNNER G. E. LEVEQOE

Jan 1, 1942

By J. T. Norton, N. J. Grant, I. S., Servi

Coarse grained high purity aluminum was tested in creep at temperatures of 400° to 1200°F to develop subgrain structures. Measurements of subgrain size, distribution, and rotation were made from X-ray diffraction patterns. Subgrain size and distribution were checked metallographically and the size was compared with average slip band spacing. The slip family was determined for several specimens. THE interest and research recently evident abroad in the role of subgrain formation and polygon-ization as a contribution to the creep of metals at elevated temperatures is deserving of greater attention in this country. Such metallic subgrains can be defined as macroblocks existing within the grains. The general observation has been that the macro-blocks which belong to the same grain have a maximum difference in orientation of a few degrees. In spite of the considerable amount of work that has been done since Jenkins and Mellorl observed the "division of existing crystals into smaller units when deformation occurs at an annealing temperature," the subject of subgrain formation is only now receiving truly active discussion and investigation. The existence of subgrains has been revealed by metallographic methods, as in the work of Jenkins and Mellor,1 and by X-ray methods, first applied to this problem by Homes.' Hirst3 and Calnan and Burns4 applied the back-reflection Laue technique to the study of coarse grained specimens. Wood et al.5 and Greenough and Smith' examined the ring obtained with a back-reflection camera for the study of fine grained specimens. In addition to the above, the transmission technique was used by Wood.6 A special technique was developed by Guinier and Tennevin8 in order to improve the resolution. Metallographically, the subgrains have been observed directly on the surface of deformed specimens by Wood et al.,3 or have been made evident on repolished surfaces by applying a suitable etching reagent. The latter technique, first suggested by Lacombe and Beaujard,9 was then improved by Wyon and Crussard.10 Subgrains can be formed in single crystals after small amounts of bending followed by heating after this cold work, or during deformation at elevated temperatures. The first phenomenon was analyzed by Cahn11 for the simple case of pure bending followed by annealing. Cahn suggested a mechanism of subgrain formation based on the dislocation theory and called this phenomenon "polygonization." He extended this mechanism to the more complex case of local bending, such as the bending which may occur when a polycrystalline specimen is deformed in tension. Cahn's suggestion was later found quite consistent with the results obtained by Dunn and Daniels." An explanation has been presented recently regarding the formation of subgrains during deformation at elevated temperatures by Chang and Grant.'" In general, there are two schools of thought on the subject. One, according to Wood et al.,5 is that subgrain formation is a mechanism of deformation which is operative under certain conditions in the same way that the slip process is the mechanism of deformation which is operative under other conditions. The boundaries between the subgrains undergo a viscous flow which contributes substantially to the deformation of the material. The second, according to Cahn,13 Wyon and Crussard,10 and Chang and Grant,18 is that subgrain formation is the effect of simultaneous deformation and annealing and is,

Jan 1, 1953

New York Meets first Wednesday after first Tuesday of each month. DAVID H.-BROWNE, Chairman, JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. . ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 11, 1915

By Howard Eavenson

PRIOR to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and was usually used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia-which was then regarded as the standard coking and gas coal of the coun, try, and the best coal available anywhere for these purposes. With the advent of the by-product oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for cokemaking, gas and other metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than the best of the coal from the Pittsburgh seam, or than any northern coal, and in by-product ovens produce coke that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these seams is shipped in great quantities without beneficiation and is lower in ash and sulfur than the best washed product from any seam mined in the north.

Jan 1, 1932

By H. H. Podgurski, Hsun Hu

Large cryslals of high-purily iron (99.996+ pcl) cannot be obtained by the usual strain-ameal technique. Repealed phase transformation by thermal cycling prior to crilical deformation improves the capabilily of cryslal growith but fails to yield satisfactory crystals. Imperfect columnar crystals can be produced by the phase-transition method. The addition of a small amounl (0.005 wl pet) of nilrogen IT was reported'-4 that for metals of very high purity the usual procedures of the strain-anneal technique fail to produce large crystals. This was eliminates practically all the difficulties in crystal growth by the normal strain-anneal procedures. An actual example is presented, showing that most parts of a strip have been converted into a large crystal by this method. The addition of nitrogen, which can be removed from iron with less difficulty, is believed to be more desirable than carbon additions for the same purpose. thought to be due to the strong tendency for recovery in the high-purity metals: hence the critically strained matrix undergoes polygonization instead of recrystallization upon annealing for crystal growth. Talbot1,2 succeeded in overcoming this difficulty by adding 0.03 to 0.04 pct C to high-purity iron before critical deformation. followed by annealing in hydro-

Jan 1, 1965

By C. W. Goodale

I. INTRODUCTION. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and -is this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 8, 1913

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd.: (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the, St. Eugene Concentrator, Moyie, B. C., and (3) the. Tadanac (Customs) Concentrator,Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals -lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a FIG. 1.-THE SULLIVAN CONCENTRATOR, CHAPMAN CAMP, B. C. (NEAR KIMBERLEY, B. C.). low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential-flotation.

Jan 1, 1927

By G. R. Hodgson, M. P. Lebourg

The introduction in the field of a new type well completion called for the setting of tubing open-ended in the well before perforating the casing. This paper describes a new perforating tool of the shaped charge expendable type, small enough to pass through tubing and powerful enough to perforate the casing. The perforations are produced at an angle and are large enough for optimum production. Performance of this tool in targets and under various well conditions is described. Very often no lifting equipment will be available at the well. In some cases, pressure will exist in the well at the time of the perforating operation (workover wells or multiple trip perforation) ; therefore, new equipment and new technique for the perforating operation were devised. This paper describes this equipment and technique, particularly casing collar recording, sheave support, and cable pull-down device. this last item being necessary for wells under pressure. Results obtained with this tool in the field are given. INTRODUCTION One of the key requirements for the introduction in the field of a new method of permanent well completion was the development of a new perforating method involving the use of a perforating gun small enough to go through tubing and with enough penetrating power to perforate the casing satisfactorily. The equipment described in this paper was basically designed to go through open-ended two-in. tubing and to perforate 5 1/2 in. casing. The equipment is illustrated in accompanying figures. NEW COMPLETION METHOD With the new permanent type well completion, the production string of casing is run and cemented through the potential producing zone. Open-ended tubing is -then run into the well and used to replace the drilling fluid with oil or water. The amount of the oil or water "cushion" can be varied according to the expected bottom hole pressure. Thus, if desired, the hydrostatic head can be greater, equal to, or less than the expected pressure within the zone to be perforated. Mud having been displaced, the tubing is -then positioned so that the end is above the zone to be perforated. The Christmas tree and flow lines are installed and tested. The drilling rig can now be removed from the well since it is not necessary for the perforating operation, thus resulting in a saving in rig tme. The perforating equipment is then moved to the well and the gun lowered through the tubing. After the gun passes out of the open end of the tubing, the depth measurements are correlated with casing collars and the gun placed opposite the zone to be perforated. Upon firing, the gun body is shattered and falls to the bottom of the well. Since the lubricator has been closed before firing, it is possible to withdraw the casing collar locator and head and then open the well immediately to the tanks. DESCRIPTION OF GUN An investigation of two basic types of Perforators, namely a bullet perforator and a shaped charge gun, was undertaken towards the development of a gun to meet the aforementioned requirements. Preliminary tests on various bullet perforator designs within the diameter limitations did not give results encouraging enough to warrant further study. Somewhat better results were obtained by using conventional shaped charges; but, as in the case of the bullet types, the necessarily small overall diameter proved to be a severe limitation and resulted in insufficient penetration. A shaped charge employing a new design was developed which gave excellent penetration. These shaped charges were designed to produce a large hole directed upward at a 45" angle. In order to obtain the maximum space possible for these charges, it was decided to use an expendable carrier made of drillable material, usually aluminum, which would shatter at the time of firing, leaving only harmless fragments at the bottom of the hole. The fixed spacing is five shots per ft. wit11

Jan 1, 1952

By Francis F. Lucas

A microscope objective of given numerical aperture, when used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability—the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise when the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500 uu and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.60 N. A. are now an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Kohler and Dr. M. Von Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 uu which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 1, 1926

By S. C. Jones, J. A. Davis

This paper describes displacement mechanisms of micel-lur solution slugs, displuced by a thickened water "mobility buffer", in a glass micromodel and in consolidated Berea sandstone cores. Colored motion pictures, taken through a microscope, recorded interactions on a pore-to-pore bash in the micromodel. Production and differential pressure data from consolidated cores previously waterflooded to residua1 oil saturation revealed displacement mechani.sm.s macroscopically. Oil is displaced miscibly, while interstitia1 water is displaced immiscibly by the injected micellar. solution slug. Part of this water is dispersed and carried near the lead ing edge of the .slug, and some may remain as a residual saturation. Thickened water displaces any residual water. It also emulsifies with the. slug material, thereby displacing it. The displacement sequence forms banks of oil and water with relatively constant fractional flows, saturations, and mobilities. The mobility of oil and water flowing ahead of the .slug defines .slug viscosity required for stable displacement. Equations are presented that describe. several aspecis of the displacement flow behavior: oil breakthrough, oil cut during production of the stabilized bank, breakthrough of banked water and the resulting decreased fractional flow of oil, fluid mobilities, etc. Breakthroughs, calculated from the equations, are compared with experimental data. Slugs of micellar sollution, ranging from 1 to 5 percent PV, produced unusually high oil recoveries (up to 100 percent) in previously waterflooded consolidated cores. Investigation of the effect of mobility buffer size on oil recovery indicated that recovery is reduced in 3-in. X 4-ft cores for mobility buffer sizes .smaller than 50 percent of the pore volume. Introduction A new oil recovery process,* conceived in 1962, utilizes a slug of micellar solution' that has sufficient viscosity to avoid an unfavorable mobility ratio with respect to the oil and water it displaces. These micellar solutions are composed of hydrocarbons, water, and surfactants, and may contain electrolytes and co-surfactants. The micellar solution is displaced by a "mobility buffer". The mobility buffer is a bank of reduced-mobility fluid, preferably an aqueous polymer solution. The entire system is displaced by unthickened water. This paper describes some of the microscopic and macroscopic displacement mechanisms observed during laboratory development of the fluids for a potential field test. Microscopic phenomena were observed photographically in a specially constructed glass flow model and macroscopic data were taken from constant rate, tertiary displacements conducted in Berea sandstone cores. Qualitative Description of Micellar Solution Flooding This section qualitatively describes displacement mechanisms that occur when a slug of micellar solution is injected into a previously waterflooded core. The slug completely removes oil from the portion of core it contacts, and banks oil in the process. The oil saturation in this bank and the flowing WOR reach definite, fixed values that are determined by water and oil mobilities and slug characteristics. This zone of constant WOR and oil saturation will be called "stabilized oil bank" in the following discussion. When this stabilized bank reaches the outlet end of the core, the oil cut jumps from zero to a constant value equal to the fractional flow of oil. Saline water has little or no solubility in the slug. Because of this. the slug displaces in-place brine immiscibly. During slug injection, most of the brine is displaced ahead of the slug, some is carried along in the leading portion of the slug, and part of the brine may become immobile. The immobile, residual brine is later miscibly displaced by thickened water. Displacement of all the oil and only part of the water during slug injection results in a higher fractional flow of oil ahead of the slug than occurs when all the water is displaced after injection of thickened water is begun. The slug spontaneously emulsifies fresh (low-salt content) water. By emulsification, the slug can become infinitely diluted, and hence totally displaced, by thickened water. Fluid saturations in the core are shown schematically in Fig. 1. Parts A and B show conditions before and after the start of the thickened-water injection, respectively. Since thickened water displaces any residual brine by-

Jan 1, 1969

By R. E. Ogilvie, N. L. Peterson

DURING the past few years there has been considerable effort devoted to the understanding of radiation effects on materials. The concept of the Frenkel defect and other lattice defects suggests that radiation may alter the rate of many metallurgical phenomena, especially those which are diffusion controlled. In 1953 R. R. Coltman and T. H. ~lewitt' found an appreciable effect on the ordering rate of Cu,Au due to fast neutron bombardment. Since then several rather comprehensive theories have been proposed on radiation enhanced diffusion in solids.2"4 If the energy of the radiation is above the threshold energy for the removal of atoms from their lattice sites, Frenkel defects will be produced. These defects can be produced uniformly throughout a relatively thick specimen by high-energy X-rays permitting bulk property studies without the limitation of sample dimensions. In this work high-purity arsenic containing 30 ppm of impurities was allowed to diffuse from the gase- ous phase at 700°C into single crystals of p-type germanium containing 0.1 ppm of indium. As the arsenic diffuses into the P-type germanium, an n-type layer will form in the diffusion zone. At the p-n junction the concentration ratio of the arsenic to the indium is constant. Experimental Procedures—The germanium specimens, 10 mm by 10 mm by 5 mm, were polished and etched to a mirror finish. The specimens were then sealed off in a vycor glass capsule at 3 x 10"5 mm Hg pressure with a sufficient amount of arsenic powder to produce a one-half atm pressure of arsenic at 700°C. Specimens were annealed at 700°C without radiation. The diffusion coefficient determined from these samples agrees within 8 pct of previous work done by Fuller.' Three specimens were given diffusion anneals at 700°C in a small tube furnace centered beneath the target of a 2-mev Van de Graaff generator. The specimens when in the furnace were 10 cm directly below the target of the generator. These specimens were irradiated continuously during the diffusion run with the Van de Graaff operating at 2 mev with a tube current of 225 to 250 pamp. The intensity of the x-radiation at the surface of the specimen inside the furnace was approximately 4.5 x l05 roentgens per hr. The temperature was controlled within m2°C by a chromel-alumel thermocouple throughout this work with no observed temperature change due to the radiation. By careful lapping, the samples were polished at an angle of 5 deg to the diffusion zone, giving a XI0 increase in the visible diffusion zone. The location

Jan 1, 1960

Aamot, Olav Crone, (M'29) Chem. Engr., Elektro¬kemisk, Raadhusgt, 23; Oslo, Norway. Abadilla. Quirico A., (M'33) Min. Engr., Dir., Bureau of Mines, Manila, P. I. Abbott, Agatin T., ( J'40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Tennessee Coal Iron & R. R. Co.. 159'3 Brown Marx Bldg.. Birmingham, Ala. Abel, Raymond L., (M'28) Chem. Engr., Chief of Inspection Div., Pittsburgh Chem. Warfare Pro¬curement Dist., American Batik Bldg., Pitts¬burgh. Pa. Abel, Walter D., (M'32) Min. Engr.. Div. of Cor¬porations, State of Calif.. 403 California State Bldg., Los Angeles, Calif. Abele. Louis T., (M'31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M'311 Research Met., Mount Mor¬gan Ltd., Mount Morgan, Queensland, Australia. Abenius, Hakan V., (M'37) c/o Falu Gruva, Falun, Sweden. Abernathy. G. E., (M '33S) Geol., Kansas State Geol. Survey. Pittsburg, Kan. Abernathy, Jack. H.. (M'40) Chief Engr., Sunray Oil Co.. Philtower B1dg., Tulsa. Okla. Ahorn, Robert H., (M'19) Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. Abraham, A. W., (M'30) Petr. Engr., Richfield Oil Corp., 555 S. Flower St., Los Angeles. Calif. Abramowitz, William L., (J'40) Chem., National Oil Products Co., Harrison, N. J. Abrams, Charles Jackson, (M'36) Gen'l Supt., Climax Molybdenum Co.; Climax, Colo. Abstein, Henry T., (M'27) Yellow Pine, Idaho. Ackerman, D. E., (M'35) McKinsey & Co., 2 Wall St., New York, N. Y. Ackerman. E. Dumont, (A'3S) Petr. Geol.. Dist. Geol., Quiriquire' Dist., Standard Oil Co. of Venezuela, Caripito, Venezuela.

Jan 1, 1941

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920

By Herbert Kynor

BY THE term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal & Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal & Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910a is as follows: PENNA. COAL Co. D. L. & W., SCRANTON TEMPLE HUDSON YEAR AND HILL- TONS COAL Co., COAL CO., COAL CO., TOTAL. SIDE COAL TONS TONS TONS TONS AND IRON, TONS 1920 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919 950,786 no record 306,616 81,575 319,356 1,658,333c 1918 917,778 744,966 24,880 44,756 288,781 2,021,161 1917 757,940 838,800 5,050 57,279 164,180 1,823,249 1916 286,780 860,663 13,960 114,173 101,475 1,377,051 1915 428,819 592,169 8,253 1,029,241 1914 219,188 153,896 373,084 1913 171,505 171,505 1912 124,267 124,267 1911 40,319 40,319 1910 1,184 1,184 a. A slightly greater production than shown was obtained as the tonnage from individual operations is not shown. b. Decrease due to strike conditions in 1920. c. Does not include tonnage of D., L., & W. d. D., L., & W. decrease in 1920 due to having less mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 9, 1921

By C. H. Mathewson

MicrOscopic metallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent rnicrostructural rnosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientatjions and it is always possible to derive one from the other by some form of- rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943