Search Documents

By F. R. Zachar

IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider 'seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1952

By E. C. Burke, W. R. Hibbard

Plastic deformation in magnesium single crystals was studied by tensile tests at room temperature utilizing an improved preparation and testing technique. Consistent critical resolved shear stress values for basal slip were obtained. The advent of pyramidal slip at room temperature was rationalized upon the basis of grip constraints. A bend-twinning hypothesis was advanced as an explanation of mechanical twinning which occurs as a complex stress-relief mechanism. INVESTIGATIONS of the plastic deformation of magnesium have been limited to the determination of the fundamental kinetics which may be summarized as follows: 1—Twinning on the {102).l 2— Slip on the (001) plane in the [loo] direction at room temperature.' 3—Slip on the {101) or {102) plane in the [loo] direction above 225°C." 4—Critical resolved shear stresses for basal slip in tension at room temperature of 83 g per sq mm with a variation from 57 to 127 g per sq mm." Bakarian' studied the compression of thin wafers of magnesium single crystals and classified the components of the deformation mechanisms as follows: 1—The Basal field: (001) at an angle of less than 20" to the compression surface. Fracture along {101} or slip on (001) followed by {101} fracture. 2—The prism field: (001) at an angle greater than 60" to the compression surface. Twinning on the {102) generally occurring during the early stages of loading, basal slip in the areas of original orientation and (001) slip within twins. 3—The central field: (001) at angles greater than 20" but less than 60" to the compression surface. Slip on the (001). 4—The critical resolved shearing stress for {101} slip above 225°C was 400 g per sq mm. Observations of mechanical twins in hexagonal close-packed metals have been summarized by numerous investigatorsb-' emphasizing a lateral or rotational atomic adjustment, in addition to the pure twinning shear, and the importance of reorienting the basal plane to a position more favorable for continued slip, rather than the resulting small dimensional changes. Criterion for the operative twinning planes has not been clearly established. Schmid and Boas hurmised that an energy condition related to the atom movements is the determining factor. MillerQ bserved that twinning stresses in zinc crystals decreased as the amount of prior deformation increased. Preparation of Specimens Magnesium single crystals % in. in diam x 8 in. long were grown from the melt under an argon atmosphere in a gradient furnace similar to that described by Jillson." Magnesium containing 0.018

Jan 1, 1953

By Benjamin F. Merembeck

A mutispectral scanner (MSS) obtains remotely sensed data of the earth's surface in vector form, one vector element for each spectral sensing band of the MSS. Data generated by either airborne or orbiting MSS systems are organized in a lattice of scan lines and elements within scan lines. Each element, called a pixel, is represented by an observational vector and corresponds to a relatively small specific area on the ground. The total observations for a sensed scene frequently are in the millions and are composed of a number of populations, each representing a different land form category. Based on samples from the populations, the mean vectors, or spectral signatures, and the covariance matrices for the categories may be estimated. From these, an among category covariance matrix and a combined within category covariance matrix can be found. The total among category variance is the trace of the among category covariance matrix. Canonical analysis finds a linear transformation matrix such that the first transform variable accounts for the maximum possible part of the total among category variance. Similarly, the second transform variable, orthogonal to the first, accounts for the maximum possible part of the remainder of the total variance, and so on. Such transformation often results in over 95 percent of the total variance accounted for in the first three canonical variables, even though the initial number of spectral bands exceeded twenty. Transformation of bulk data into three canonical variates allows color map products to be developed by assigning each variable to a different basic color. Such color products are believed to be more useful for photo-interpretation than color products resulting from any combinations of three of the initial spectral bands.

Jan 1, 1977

By J. R. Finlay

BEFORE entering into the statistical part of this article, some general comments may be ln order. Each important war seems to introduce a new atmosphere and a new epoch. The Civil War led to the period of great interior development in North America, of the transcontinental railroads, and of large-scale manufactures. The first World War introduced the general use of the automobile, the building of a huge network of highways, the radio, and household engineering. Now I expect World War II also to introduce some new ways of living. Transocean aviation will become a commonplace; we shall probably have much more of an eye to our military and naval establishments and be more conscious of Eastern Hemisphere affairs instead of thinking so exclusively of the Western. Each war has also multiplied government expenditures and taxes; and to this rule the present one will certainly be no exception.

Jan 1, 1944

Map

Jan 1, 1958

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By Joseph T. Singwald

INTRODUCTION THE purpose of this chapter is to present the diagnostic features (geologic, mineralogic, chemical, and physical) of the principal types of hypogene ore deposits recognized in current genetic classifications, and to classify the ore deposits of the western United States into those types. The genetic divisions used and the criteria determining them are essentially those followed by Lindgren in his Mineral Deposits. Deviations from Lindgren represent either changed conceptions since 1928 (the date of the third edition of Mineral Deposits) due to advance in knowledge or the inevitable differences of opinion between experts in active fields of investigation. Though nineteen economic geologists have been given free hand in presenting their particular topics, there are no fundamental departures in the chapter from the principles set forth by Lindgren. It would be entirely beyond the capacity of a single chapter to give a comprehensive geologic description of all the ore deposits of the western United States. Descriptions of individual deposits have been restricted to those features that are of most diagnostic genetic value. All of the more important deposits receive that much attention. Deposits of lesser economic importance and those inadequately known geologically are treated more briefly or merely cited under what seems to be their proper genetic assignment. The geographic limits of the descriptive matter are the Black Hills and the United States between the Rocky Mountains and the pacific Coast. Capacity of the chapter has made it necessary to impose these geographic limits.

Jan 1, 1933

By A. B. Kinzel

SILICON, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have devel-oped procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, and the terns "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.1 In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve said further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treat-ment, he does not mention the existence of carbon in the alloy; neverthe-less, lie reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1939

By Stewart R. Wallace

Members of the Society, it is a very great honor for me to be here today and to have the opportunity of telling you about some things that have been accumulating in the back of my mind for some time. Before attempting to do so, I should acknowledge my debt to the many people who are responsible for my presence here this afternoon. To do this properly, however, would consume much of my allotted time and I will therefore mention only two men, both of whom were directly involved in the discovery of the Henderson ore body. The first of these was Robert Henderson, now dead, who at the time the work was going on was vice president of Western Operations of the Climax Molybdenum Co. Truly, he provided the environment that permitted the exploration program to function effectively, and the deposit appropriately bears his name. The second man I meant to mention was resident geologist at Urad at the time of the Henderson discovery. I think I should explain right here that the Urad ore body and the Henderson ore body, although entirely separate, are closely related deposits, and that both are located at Red Mountain in Clear Creek County, Colo.

Jan 6, 1975

By L. C. Brown, J. S. Kirkaldy

Measurements have been made of carbon diffuswn in the five ternary austenites Fe-C-Si, Fe-C-Ni, Fe-C-Co, Fe-C-Mn, and Fe-C-Cr in which the carbon (component 1) diffuses through interstitial sites and the ternary addition (component 2) diffuses substitutionally. Values of the diffusion-coefficient ratio, D12/D11 were determined for each system with finite couples using the transient equilibrium method. The effect of temperature and of concentrations of both the carbon and substitutional component upon D12/D was examined and was found to agree with the theoretical predictions. It is concluded that within an experimental uncertainty of 10 to 15 pct, it is possible to calculate the ratio D12/D11 from purely thermody-namic data. Difficulties of measuring the other off-diagonal coefficient, 4,, are discussed. Any quantitative attack on the fundamentals of the hardenability problem in steel must begin with the multicomponent diffusion formalism and with the accumulation of data pertaining thereto. In a recent paper Kirkaldy and purdy 1 employed the formalism derived from irreversible thermodynamics to treat the problem of diffusion in ternary austenites. In the latter solutions, carbon diffuses through interstitial sites and the substitutional component diffuses through the lattice. Examples were given of diffusion in the systems Fe-Mn-C and Fe-Si-C. In the present paper, we present new results on and discuss their agreement with the thermody-namic theory. Since the theory has been slightly modified from the original presentation of Kirkaldy and Purdy, their results on Fe-Si-C and Fe-Mn-C have been recalculated and are presented here for completeness. The flux of the interstitial component with respect to a fixed lattice framework can be written as a linear expansion in the independent concentration gradients, where X1 and X2 are the independent thermody-namic forces in the lattice fixed frame of reference. These forces can be obtained from the general statement for forces in a volume fixed frame2 if the partial molar volume of carbon atoms is set equal to zero and that of the substitutional component 2 is set equal to unity, viz where the are the chemical potentials and the N's are mole fractions. Introducing into [3] and [4] the function If, as suggested by statistical arguments, the off-diagonal interaction L12 is sufficiently small, [6] reduces to i.e., the coefficient ratio becomes purely thermo-dynamic. The activity of components 1 and 2 in a dilute ternary system (standard state at infinite dilution) may be represented by the expansion3

Jan 1, 1964

By Jay N. Fairbanks, Richard G. Robinson

This paper discusses a computer program and related formulas for fire fighting responses by coal mine personnel. The computer will interpret the mine air analysis, print reports, and provide relevant graphs allowing quick and accurate responses to coal mine fires.

Jan 1, 1983

By Frederick K. Allgaier

As part of an ongoing research program, the Bureau of Mines, U.S. Department of the Interior, is monitoring surface subsidence over six longwall panels at three Utah coal mines. These sites are characterized by mining depths of 244 to 610 meters (800 to 2,000 ft .), thick and massive sandstone layers in the overburden strata, multiple seam mining, extraction heights of approximately 1.8 to 3 meters (6 to 10 ft.), and rugged surface topography. Maximum subsidence, angle of draw, timing relative to mining, horizontal strain, and rate of subsidence development are being determined and correlated with mining and geologic variables. Results to date indicate the maximum vertical subsidence over the monitored panels ranges from 0.6 to 0.9 meters (2 to 3 ft.). The major factors controlling the amount of subsidence are the panel dimensions and the status of adjacent panel mining. Only minor surface cracking at the panel ends was evident at any of the sites. In all cases, there was a time lag of several months between the start of mining and subsidence at the surface. As subsequent panels are monitored and additional data become available, better estimates of the effect of various site characteristics on the subsidence will be possible. Ultimately, improved prediction capabilities will allow mine operators in the West to evaluate the potential for subsidence-related damage which could affect the current or future land use above the mine.

Jan 1, 1982

By G. F. Comstock

The subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. That the quality of the metal and the mill practice must have something to do with them. The first point of view was most ably and logically presented by J. E. Howard,' and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior road-bed; while the railroad men, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work done in this laboratory, as well as the work of other investigators, of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. Within the last year or two, however, since the method of etching polished sections for the microscope with a oupric chloride solution has been tried systematically on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 1, 1920

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

By George H. Anderson

A CHAPTER of appealing interest was added to the industrial history of the Southwest early in June, when the War Production Board gave final approval to the erection of a blast furnace, a battery of coke ovens, an ore-beneficiation plant, and other facilities for the production of pig iron in northeastern Texas, just north of the East Texas oil field. For many years the people of Texas and adjoining states have cherished the ambition and desire that eventually an iron and steel industry drawing upon local mineral resources would be established to serve Southwestern markets. The existence in this vicinity of valuable deposits of iron ore, limestone, and coking coal has been known in a general way for many years, and efforts have been made from time to time to use them in the production of iron. The present development promises to bring to realization the dreams of the men who have visualized what the establishment of this basic industry would mean to the region.

Jan 1, 1942

By GERALD A. WARING

ALASKA'S coal consumption is now about 130,000 tons annually. About one-quarter of this amount is used in the southeastern part of the territory and in settlements on the western coast and comes from Seattle and from British Columbia mines. About 60,000 tons is sub-bituminous coal from the Healy River mine in central Alaska, and is used mainly at Fairbanks, sixty miles to the north, for heating and the development of electric energy, for the city and the gold-dredging operations of the Fairbanks Exploration Co. The remaining 40,000 or 50,000 tons is bituminous coal from Matanuska Valley, in the south-central part of the territory. These coal deposits extend intermittently for about forty miles along the valley, which trends eastward from the upper end of Cook Inlet.

Jan 1, 1934

By Peter N. Calder, G. H. Blackwell

The development of an open pit slope monitoring system, from equipment selection and justification to complete computer data storage and analysts, Is described. Methods of overcoming the Limitations of the electronic transit/distance measuring device and survey system selected are discussed. Results of the monitoring program showed that blasting was a major cause of Instability, and, after much experimentation, suitable blast patterns for mine production and pit wall integrity were designed. The experiences gained with double benching 'and wall cleanup procedures are discussed . The monitoring program also indicated that water was a contributor to instability, and methods of dealing with water In a rock with a low storage coefficient and transmissibility are described. Because of the danger of falling rock, photogrammetric methods are used for joint mapping and analysis, this work being contracted out. Joint strengths are measured on-site using a portable shear tester. Finally, a discussion of a complex failure is given.

Jan 1, 1983

By Raymond D. Sloan

Retaining third place in crude-oil production among the nation's oil-producing states, Oklahoma's output in 1942 totaled 137,792,000 bbl., a decline of 9.4 per cent from the previous year's total of 152,117,000 bbl. Production declined from an average of 403,000 bbl. daily in January 1942 to an average of 355,000 bbl. during December, a reduction of 48,000 bbl. daily (11.9 per cent) during the year. At the end of 1942 it would appear inevitable that the downward trend in production will continue in 1953 unless halted in the immediate future by greater than normal discoveries and development. To Jan. I, 1943, Oklahoma has produced 5,067,013,000 bbl. oil crude oil. Development and Exploration Development dropped abruptly in 1942, reflecting the lack of any sizable discoveries and the effect of the provisions of Federal Well Spacing Order M-68, which became effective in December 1941. In all, 1210 wells were drilled in 1942. This represents a decrease of 42.7 per cent from the 1941 total of 2110. Of the total wells completed, 553 (45.7 per cent) were oil wells with an average initial production of 443 bbl.; 102 (8.4 per cent) were gas wells with an average initial of 3,359,000 cu. ft.; and 555 (45.9 per cent) were dry. Although the number of completions declined sharply, the total of 320 wildcats completed (26.4 per cent of all wells) repre-sents a decrease of only 2.7 per cent from the previous year's figure of 329. Of the wildcats drilled, 44 (13.8 per cent) were oil wells, 13 (4.0 per cent) were gas wells, and 263 (82.2 per cent) were recorded as failures. Reconditioning of wells throughout the state resulted in a total recompletion of 355 wells. Of these, 234 were oil wells with a combined initial production of 96,808 bbl., 32 were gas wells with a total initial of 381,488,000 cu. ft., and 89 were abandoned. None of the 26 pools found in 1942 has developed into a major discovery. The Pauls Valley pool, Garvin County, is the most outstanding. Since its discovery in April, 14 wells with an average initial of 1898 bbl. have produced 803,000 bbl. of 42' gravity oil from the Bromide zone. Development in this pool is believed to be almost completed. Other of the more important discoveries are the East Watchorn pool, Pawnee County; Guthrie Townsite and West Navina, Logan County; Brooksville and Macomb, Pottawatomie County, and the Liberty and Northeast Lucien discoveries in Noble county. The East Watchorn pool, at the close of the year, had 14 completed oil wells with an average initial of 989 bbl. from the Wilcox sand at 3930 it.; Guthrie Townsite, one well with an initial of 840 bbl. from dolomite at 5600 It.; West Navina, six wells with an average initial of 284 bbl. in the Lay ton sand at 5050 ft., Brooksville, eight wells in the Hunton at 4800 ft. with an average initial 01 355 bbl.; Macomb, one well with an initial of 160 bbl. in the IIunton at 4700 ft.; the Liberty pool, one well with an initial of 1268 bbl. in the second Wilcox at 4500 ft., and two wells in the Tonkawa sand at 2500 ft., with an average initial of 230 bbl. In the Northeast Lucien pool, four wells were completed in the Wilcox at 5380 ft. for an average initial of 1164 bbl., and one well was completed in the Viola lime at 5255 ft. for an initial of 55 barrels.

Jan 1, 1943

By Raymond D. Sloan

Retaining third place in crude-oil production among the nation's oil-producing states, Oklahoma's output in 1942 totaled 137,792,000 bbl., a decline of 9.4 per cent from the previous year's total of 152,117,000 bbl. Production declined from an average of 403,000 bbl. daily in January 1942 to an average of 355,000 bbl. during December, a reduction of 48,000 bbl. daily (11.9 per cent) during the year. At the end of 1942 it would appear inevitable that the downward trend in production will continue in 1953 unless halted in the immediate future by greater than normal discoveries and development. To Jan. I, 1943, Oklahoma has produced 5,067,013,000 bbl. oil crude oil. Development and Exploration Development dropped abruptly in 1942, reflecting the lack of any sizable discoveries and the effect of the provisions of Federal Well Spacing Order M-68, which became effective in December 1941. In all, 1210 wells were drilled in 1942. This represents a decrease of 42.7 per cent from the 1941 total of 2110. Of the total wells completed, 553 (45.7 per cent) were oil wells with an average initial production of 443 bbl.; 102 (8.4 per cent) were gas wells with an average initial of 3,359,000 cu. ft.; and 555 (45.9 per cent) were dry. Although the number of completions declined sharply, the total of 320 wildcats completed (26.4 per cent of all wells) repre-sents a decrease of only 2.7 per cent from the previous year's figure of 329. Of the wildcats drilled, 44 (13.8 per cent) were oil wells, 13 (4.0 per cent) were gas wells, and 263 (82.2 per cent) were recorded as failures. Reconditioning of wells throughout the state resulted in a total recompletion of 355 wells. Of these, 234 were oil wells with a combined initial production of 96,808 bbl., 32 were gas wells with a total initial of 381,488,000 cu. ft., and 89 were abandoned. None of the 26 pools found in 1942 has developed into a major discovery. The Pauls Valley pool, Garvin County, is the most outstanding. Since its discovery in April, 14 wells with an average initial of 1898 bbl. have produced 803,000 bbl. of 42' gravity oil from the Bromide zone. Development in this pool is believed to be almost completed. Other of the more important discoveries are the East Watchorn pool, Pawnee County; Guthrie Townsite and West Navina, Logan County; Brooksville and Macomb, Pottawatomie County, and the Liberty and Northeast Lucien discoveries in Noble county. The East Watchorn pool, at the close of the year, had 14 completed oil wells with an average initial of 989 bbl. from the Wilcox sand at 3930 it.; Guthrie Townsite, one well with an initial of 840 bbl. from dolomite at 5600 It.; West Navina, six wells with an average initial of 284 bbl. in the Lay ton sand at 5050 ft., Brooksville, eight wells in the Hunton at 4800 ft. with an average initial 01 355 bbl.; Macomb, one well with an initial of 160 bbl. in the IIunton at 4700 ft.; the Liberty pool, one well with an initial of 1268 bbl. in the second Wilcox at 4500 ft., and two wells in the Tonkawa sand at 2500 ft., with an average initial of 230 bbl. In the Northeast Lucien pool, four wells were completed in the Wilcox at 5380 ft. for an average initial of 1164 bbl., and one well was completed in the Viola lime at 5255 ft. for an initial of 55 barrels.

Jan 1, 1943