Search Documents

By Clarence Zener

THE heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an under- standing will involve two distinct types of inquiry: (I) the direction of the trans- formation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed here in steel such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron- alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data being obtained from the simple binary and ternary equilibrium diagrams. FUNDAMENTAL EQUATIONS In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body- centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may be regarded as filling all the lattice positions of a given type. The introduction of the fundamental equations of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1946

By Albert Ledoux

SEVERAL years ago my firm was representing the Mt. Lyell Co. of Australia, which was shipping its blister copper to a refining works in the United States. After the contract had been running for many months, the superintendent of these works discovered that if water was poured upon the surface of the bars much of it would disappear into the interior through blow holes. -Some experiments made by him showed that this could be a considerable amount, so that copper which had been rained on before it was weighed, although the surface appeared dry, nevertheless would contain water. It had frequently occurred in our experience-as samp-lers that the drillings from a lot taken by boring would come out quite wet, and in some cases, indeed, water would drip into the sample pan placed below the bars, due to the fact that the drill had penetrated a cavity or cavities containing water, which presumably got into the cavities at the time the copper was water-cooled after casting, there being, perhaps, no outlet to the surface. So far as I know, until this discovery at the refining works, no. one had thought that rain could penetrate into the interior of blister copper; at least in any quantity sufficient to be considered.

Jan 10, 1922

BRANCH COUNCILS MINING BRANCH R M Foose, Chairman (Industrial Minerals) Carroll A Garner (Coal) J V Beall, Eastern Secretary A B Cunmins (Industrial Minerals) R E O'Brien, Western Secretary E D Gardner (Mining, Geology, and Geophysics) Carroll F Hardy (Coal) Philip J Shenon (Mining, Geology, and Geophysics) R E Byler (Minerals Beneficiation) A C. Callen (Mineral Industry Education) Grover J Bolt (Minerals Beneficiation) R J Lund (Mineral Economics)

Jan 1, 1951

By William P. Shinn

IT seems proper to present in the Transactions of the Institute, from time to time, formal record of the advances made in the arts and sciences to which our organization is devoted-milestones in the highway of progress-from which our successors may measure what they in their turn have gained. The admirable address of the Hon. Abram S. Hewitt, then president elect of the Institute, on "A Century of Mining and Metallurgy in the United States," read at the opening of the meeting held in this hall in June, 1876, forms a point of departure, and the conclusion of the eighth decade of the nineteenth century and the end of the first five years of our country's second century seem to offer a fitting time for again making up our record. The period since 1875 has been marked by a degree of activity in mining and metallurgical industry never before equalled in our history, while the progress made in the science and art has been, if possible, still more noticeable. Whether we consider the mining of iron, ore, and coal, or of the precious metals,-the advances made in smelting the former and in reducing the latter, the extraordinary increase in the production of Bessemer steel, or the science of Thomas and. Gilchrist, which makes the hitherto rejected phosphorus the corner-stone of success,-the past five years are alike memorable for the progress they have shown and to some of the most marked features of this progress I will now oriefly call your attention. It may be of interest in this connection to note the following figures, showing the growth of the population of the United-States during the last three decades :

Jan 1, 1881

By B. Egeberg, H. B. Smith

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By H. B. Smith, B. Egeberg

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By H. O. Hofman

PAGE I. Introductory,.......... 258 11. Condensed Account of Past and Present Plants,. .. 259 111. The Ores. Table I., Average Analyses,..... IV. Metallurgical Treatment—Roasting OF Ores,... The Allen-O'Hara Furnace,....... The Wethey Furnace,........272 The Pearee Turret-Furnaces,....... 273 The MacDougall Furnace,.......275 Original MacDougall,.......276 Herreshoff,......... Evans-Klepetko,........ General Results (Table II.),.......282 V. Smelting Ores in The Blast-Furnace,...,. Table 111. Examples of Montana Blast-Furnace Smelting,. 284 Table IV. Analyses of Coke and Coke-Ash,. .. . VI. Smelting Ores in the ReveRberatory Matting-Furnace,. 289 Table V. Percentage of Components of Charge,. .. 290 Table VI. Analyses of Flue-Dust and Briquettes,. .. Table VII. Examples of Montana Reverberatory-Smelting,. 292 Table VIII. Analyses of Coals,...... Table IX. Analyses of Producer-Coal and Ash,. .. Details of Practice,........297 VII. Converting Coppr-Matte,....... 302 Table X. Analyses of Materials of Converter-Linings,. . 306 Table XI. Montana Converters,......308 Yield of Metal..........308 VIII. Electrolytic Refining of Copper,..... Refining of Cathodes,........ 313 Table XII. Details of Electrolytic Refineries,. .. . Table XIII. Efficiency of Some Rocky Mountain Coals,. . 316 I. Introductory. In 1901,* this country produced 268,782 long tons of fine copper. Of this total, Montana is credited with 102,621 long tons, or 38.2 per cent.

Jan 1, 1904

By Jay A. Carpenter

THIS preliminary report from the Committee to Study Relations Between Students and the Institute is submitted to our member- ship for consideration and discussion before the general subject comes up for action at the Annual Meeting in February. At present, the A. I. M. E. has a dual relationship with mining students, each relationship in no may connected with the other. To the individual student the Institute offers for $2 a year a Student Associateship in the Institute which carries with it a subscription to MINING AND METAL- 'LURGY, a watch fob, and the privilege of becoming a Junior Member after graduation without payment of the -first year's dues, if one's application is accepted. To the student's college society it offers the privilege, upon application, of becoming 'an Affiliated 'Society, which brings with it no specific supervision or aid, and in turn requires no specific conditions as to membership, fees, or rules. This Affiliated Society is distinctly a school organization which Student Associateship in the Institute can he given special status or ignored, is the local .society sees fit.

Jan 1, 1934

Page Laboratory Methods...........................127 Special Analytical Methods.......................127 Improvements in the Accuracy of the Vacuum-fusion Method for the Determination of Oxygen in Steel....................127 Quantitative Spectrochemical Analysis of Mixtures of Gases.......131 Oxygen Samples from Open-hearth Bath...............133 Rapid Analysis of Sample for Alumina.................139 Accurate Carbon Analyses in Low-carbon Steel.............139 Laboratory Technique for Study of Reactions Involving Liquid Metal. . . . 142 Rotating Liquid Crucibles......................143 Stationary Crucibles.........................145 Jones and Laughlin Experimental Furnace...............148 Vacuum Melting..........................149 Measurement of Temperature of Liquid Iron and Steel;..........149 Pouring and Teeming Temperatures..................149 Bath Temperatures.........................151 Plant Methods.............................154 Methods of Studying Slags.......................154 Sampling Slag in the Open Hearth..................155 Viscosity of Open-hearth Slags....................155 Petrographic Examination of Slag...................156 Statistical Methods Applied to Study and Control of Chemical Relations in Bath...............................166 Rapid Method of -Correlation Applicable to Study of Steelmaking Reactions............................166 INTRODUCTION On Thursday morning, Feb. 16, 1939, a round table discussion was held on the subject of Experimental Methods in the Study of Steelmaking. Dr. John Chipman, Professor of Metallurgy at the Massachusetts Institute of Technology, and chairman of the A.I.M.E. Committee on Physical Chemistry of Steelmaking, presided. In opening the meeting, the chairman said: "The purpose of this round table is to discuss methods of study by which more and better information on the fundamentals of steelmaking can be obtained. It was thought that a round table discussion rather than a symposium would furnish the best opportunity for those actually using various methods of study to get together and discuss their common problems. For this reason attention will be focused upon methods of study rather than upon their results. We want new and current and up-to-date discussion.

Jan 1, 1940

Page Laboratory Methods...........................127 Special Analytical Methods.......................127 Improvements in the Accuracy of the Vacuum-fusion Method for the Determination of Oxygen in Steel....................127 Quantitative Spectrochemical Analysis of Mixtures of Gases.......131 Oxygen Samples from Open-hearth Bath...............133 Rapid Analysis of Sample for Alumina.................139 Accurate Carbon Analyses in Low-carbon Steel.............139 Laboratory Technique for Study of Reactions Involving Liquid Metal. . . . 142 Rotating Liquid Crucibles......................143 Stationary Crucibles.........................145 Jones and Laughlin Experimental Furnace...............148 Vacuum Melting..........................149 Measurement of Temperature of Liquid Iron and Steel;..........149 Pouring and Teeming Temperatures..................149 Bath Temperatures.........................151 Plant Methods.............................154 Methods of Studying Slags.......................154 Sampling Slag in the Open Hearth..................155 Viscosity of Open-hearth Slags....................155 Petrographic Examination of Slag...................156 Statistical Methods Applied to Study and Control of Chemical Relations in Bath...............................166 Rapid Method of -Correlation Applicable to Study of Steelmaking Reactions............................166 INTRODUCTION On Thursday morning, Feb. 16, 1939, a round table discussion was held on the subject of Experimental Methods in the Study of Steelmaking. Dr. John Chipman, Professor of Metallurgy at the Massachusetts Institute of Technology, and chairman of the A.I.M.E. Committee on Physical Chemistry of Steelmaking, presided. In opening the meeting, the chairman said: "The purpose of this round table is to discuss methods of study by which more and better information on the fundamentals of steelmaking can be obtained. It was thought that a round table discussion rather than a symposium would furnish the best opportunity for those actually using various methods of study to get together and discuss their common problems. For this reason attention will be focused upon methods of study rather than upon their results. We want new and current and up-to-date discussion.

Jan 1, 1940

By A. T. Yu

As the first loads of Noamundi iron ore rumbled into the new 54-in. Gyratory Crusher on March 30, 1968, one of India's largest and most modern iron ore processing complexes began operations. The completion of the $13 million mining and processing complex brought to a successful conclusion the second chapter of a phased expansion program initiated in 1958 by India's gigantic Tata Iron and Steel Co. The completed complex will yield annually 2.5 million tons of washed, sized ore and sinter fines destined for Tata's furnaces at Jamshedpur. Hewitt-Robins Div. of Litton Industries was awarded the turnkey project on the basis of world- wide competitive bids. Eighty miles southwest of the city of Jamshedpur, Noamundi lies on an approximate geographic grid of 22º-5' latitude north and 85º-30' longitude east. The mine is approximately 600 ft above sea level.

Jan 11, 1968

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.' The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

By E. W. Dewing

The nature of solid solutions of sodium in non-paphitic carbon at temperatures near 1000°C has been investigated by an electrolytic technique. The activity coefficient is found to vary strongly with the heat-treatment temperature of the carbon, and an analysis of the energy terms involved suggests that this is due to variations in the Fermi level. The diffusion coefficient for sodium is in the range implying that the sodium atoms (or ions) are not bound to specific sites on the carbon, in agreement with lack of evidence for specific compounds in the activity -composition curves. In the light of These results phenomena occurring in aluminum reduction cell linings are dis-cussed. It is concluded that sodium migrates by diffusion through the carbon lallice and not the pores, and that A14C9 is formed within the lining hy The excess of NaF invariably found in used linings is formed by this reaction and by air oxidation: There has recently been much interest in the swelling of carbon which occurs when it is made cathodic in an aluminum electrolysis cell, and there is general agreement that the phenomenon is due to the penetration of sodium atoms, derived from the reaction on the carbon lattice. (NaF and AlF3 are constituents of the fused-salt electrolyte.) The low-temperature lamellar compounds of potassium with graphite are well-known, and one compound between sodium and graphite has been reported.4 There is, however, virtually no information on the basic chemistry of the interaction of sodium with nongraphitic carbon at high temperatures, although Dell3 has made some fundamental studies of rates of penetration. At the time the present work was carried out these were not available. Rapoport and samoilenkol had measured rates of physical expansion in a dilatometer, using the fractional increase in length of a carbon specimen after electrolysis in a cryolite bath for 2 hr as an index of susceptibility to cathodic swelling. Work here with a similar apparatus showed that expansion (of a 1.5-in.-diam cylindrical specimen) ceased in less than 20 hr, and that the final expansion was much more reproducible than the value at some intermediate time. This suggested that an equilibrium was being set up, and that a thermodynamic approach was required. The results obtained are not as accurate as had been hoped, but they are the only ones of their type available and have enabled useful conclusions to be drawn. The experimental work was divided into two parts: an investigation of the activity-concentration diagram for sodium in carbon, and a rough determination of the diffusion rate. For the former, most of the experiments were made with petroleum coke even though this is not a form of carbon used in cell linings. It has the advantages, however, that it is a homogeneous material, that it is low in ash, and that its structure is reasonably well understood. Anthracites and coal cokes gave results of the same type as obtained with petroleum coke, but the reprodu-cibility from specimen to specimen was extremely poor. EXPERIMENTAL 1) The Activity-Composition Diagram for Sodium in Carbon. The petroleum coke was ground, pressed at 40,000 psi into plates 19 by 9 by 2 mm without added binder, and heat-treated. The sodium activities were established by an electrolytic technique. The carbon was made anodic in a cryolite bath with an aluminum cathode, and a controlled potential, E, applied so that the sodium activity at the anode was given by ln Na = 1n asa - EF/RT [21 where as, is the sodium activity generated by Reaction [I]. The relative activity is sufficient for many purposes and is simply given by The value of Na not at present known, but when the thermodynamics of the Na-A1 system have been worked out it can be derived from the equilibrium

Jan 1, 1963

By Herbert Hoover

BOTH the directors of industry and your leaders have made great progress toward a new and common . ground in economic conceptions, which, I am confident, has had a profound effect upon our economic progress during the last few years. That is the conception that industry must be constantly renovated by scientific research and invention; that labor welcomes those labor-saving devices; that labor gives its full and unrestricted effort to reduce costs by the use of these machines and methods; that the savings from these reduced costs shall be shared among labor, employer and the consumer.

Jan 1, 1930

By Ray W. Carpenter, Ralph Hultgren, Raymond L. Orr

Heats of formation of Au-Zn alloys of compositions Au3Zn and AuZn were rneasured at several temperatures by liquid tin solution calorimetry. The data for Au3Zn show that much smaller heat and entropy effects are associated with the a2- a1 transformation than for the a1 - a transformation. This result is consistent with reported X-ray diffraction studies which indicate that the a1 and (a2 phases have ordered structures which only slightly differ, whereas the a phase is disordered. The heat of formation of AuZn(ß') does not change significantly between 322o and 8000 K, confirming that the ß' alloy remains highly ordered to high temperatures. Not many measurements have been made of the energies of order-disorder transformations in alloy phases. In many cases these energies may be conveniently determined by measuring heats of formation as a function of temperature. Many alloy phases approximately obey Kopp's law of additivity of heat capacities; as a consequence their heats of formation do not change with temperature. In ordered alloys, however, a decrease in degree of order with increasing temperature will contribute an endothermic component to the heat of formation. Thus, for ordered phases where other anomalous contributions to heat capacity in the alloy or its pure components are absent, a measured change in the heat of formation may be attributed to the energy of disordering. A portion of the Au-Zn phase diagram1" is shown in Fig. 1. The composition AuZn(ß') has a well-ordered superlattice structure of the CsCl type at room temperature. The alloy is considered to remain ordered to its melting point,1 although, from X-ray diffraction data and electromotive force measurements of zinc activities, Terpilowski3 concluded that considerable disordering began at -673°K. The Au3Zn composition is a disordered fee solid solution (a) at high temperatures. Between 693o and 543oK, the ailoy orders to form the a1 phase, having a structure based on the L12(AuCu3) type, but with a regular distribution of ordering faults in the c direction, making it tetragonal. Below 543oK, the alloy orders further by means of slight atomic shifts, without diffusion, yielding a complex long-period orthorhom-bic superlattice structure, a2.4-7 Heats of formation of Au3Zn(a2) and AuZn(ß') were measured at 363°K by Biltz et al.8 by aqueous solution calorimetry. Heat capacities of several alloys between 14.9 and 38.4 at. pet Zn in the range from 373" to 723°K were measured by Iwasaki ef al.6 Stoichiometric Au3Zn, however, was not included in the alloys measured, the nearest composition being 26.1 at, pet Zn. Also, the heating rate used for the measurements, 2 deg per min, may not have permitted equilibrium to be reached in the neighborhood of the transformations. Heat contents of solid and liquid AuZn were measured between 488o and 1138°K by Kubaschewski.9 It was decided to determine the ordering energies of Au3Zn and to check on the possible disordering of AuZn by measuring the heats of formation of these alloys at several temperatures. The present paper reports measurements by liquid tin solution calorimetry of the heats of formation of the three phases of Au3Zn at temperatures within their regions of stability, and of AuZn at a low (322°K) and a high (800°K) temperature. EXPERIMENTAL Alloy Preparation and X-Ray Examination. Ten-gram ingots of Au3Zn and AuZn were prepared by melting weighed amounts of gold (99.95 pct Au) and zinc (99.99 pet Zn) together in sealed evacuated Vycor tubes at 1060°K, followed by rapid quenching. The resulting ingots were homogenized at 900°K for 10 days. The Au3Zn alloy lost no weight in preparation, the loss from the AuZn alloy was enough to introduce an uncertainty of only 0.1 at. pet in its composition. Filings for X-ray examination were taken from various parts of each ingot and strain-annealed at 723°K for 20 min in vacuo. The Au3Zn filings were quenched rapidly to retain the disordered phase. Diffraction patterns were determined with an X-ray dif-fractometer using copper Ka radiation.

Jan 1, 1968

By J. W. Downey, A. E. Dwight, M. H. Mueller, H. Knott, R. A. Conner

Sixty new ternary equiatomic compounds are reported with a hexagonal crystal structure that is isostructural with or very similar to Fe2P, D3h-P62m. HoNiAl is a typical example, with a, = 6.9893 ± 0.0003Å, C, = 3.8204 ± 0.003Å, and c/a = 0.54 7. Three holmium atoms occupy (g): x,0,1/2 three aluminum atoms occupy (f): x,0,0; one nickel atom occupies (b): 0,0,1/2; and two nickel atoms occupy (c): 4, + , 0. The nonequivalent 1(b) and 2(c) sites give rise to two sets of unequal interatornic distances (i.e., Ho-Ni and Al-NL in the case above), which account for the prevalence of Fe2P-type tertmry compounds and the scarcity of binary examples. Unit-cell constants are presented for the sixty compounds and density measurements on the compounds HoNiAl and UFeGa confirm that three formula weights are present per unit cell. Neutron and X-ray powder diffraction intensity measurements were made on CeNiAl and HoNiAl, respectively. The atomic posiLiotml parameters in CeNiAl were determined from neutron data to be x = 0.580 5 0.001 for cerium and 0.219 5 0.001 for aluminum. An investigation of the quasibinary section between the binary compounds CeNi2 and CeA12 revealed a new ternary compound CeNiAl. The compound has a hexagonal structure and is isostructural with the prototype compound Fe2P. Additional examples discovered or confirmed in this investigation provide a total of sixty ternary compounds that are isostructural with or closely related to Fe2P. Previous investigators1'2 reported the unit-cell constants for the hexagonal compounds UFeA1, UCoAl, UIrA1, ZrNiAl, ZrNiGa, HfNiAl, and HfNiGa and the present investigation has confirmed that the compounds are isostructural with Fe2P. Independently, Steeb and petzow3 reported the same structure type for UCoAl, UIrA1, and UNiA1. However, the present results suggest a different atomic site occupancy for the component atoms in the three compounds. A detailed investigation of the relative positions of the three kinds of atoms in the compounds CeNiAl and HoNiAl will be discussed. EXPERIMENTAL PROCEDURE The equiatomic alloys were prepared from elements of 99.9+ pct purity by arc melting under a helium-argon atmosphere. After homogenization at temperatures from 700" to 900' C, a metallographic examination was performed by conventional methods, and density measurements were carried out by the immersion method in CCl4. A powder sample was prepared for diffraction studies by crushing a portion of the annealed button. X-ray diffraction patterns were obtained with a Debye-Scherrer camera, in which the annealed powder was glued to a quartz filament, and indexed with the aid of a Bunn chart. Unit-cell constants were calculated from the computer program of Mueller, Heaton, and Miller4 and d spacings were obtained by the program of Mueller, Meyer, and Simonsen.5 The intensity values were calculated from the relation I, ~ (m)(L.P.)F2 by a computer program written by Busing, Martin, and Levy.6 The absorption and temperature correction factors were neglected. An X-ray study of HoNiAl was carried out to take advantage of: large differences in atomic scattering factors for holmium and aluminum, X-ray patters free of background darkening, negligible oxidation at room temperature, and negligible weight loss in the preparation of this alloy. The neutron diffraction studies were made on a powder sample of CeNiAl contained in a -in. diam V tube and a pattern was obtained with neutrons of wavelength The neutron scattering factors employed (x 10-12 cm). In contrast to the scattering amplitude for X-rays, cesium does not have the largest cross section, however, there is a sufficient difference in the neutron scattering amplitudes to distinguish between the atomic species. The neutron transmission was high, 86 pct; therefore, absorption corrections were not necessary for the cylindrical sample. Most reflections could not be observed individually, because of the relatively large unit cell (a = 6.9756 and c = 4.0206Å) and relatively short neutron wavelength; therefore, the intensity of grouped reflections was considered. The Kennicott modification7 of the Busing-Martin-Levy program6 was employed to determine the identity of the atoms at the various lattice sites and the positional parameters. RESULTS A structure for the prototype compound Fe2P was first reported by Hendricks and Kosting;8 however, the structure was in error. The correct structure, as reported by Rundqvist and Jellinek,9 is as follows. The unit-cell constants and volumes per formula weight (V/M) are given in Table I for the sixty compounds examined in this investigation and classified as Fe2P-type compounds. The structure type was determined initially from a comparison of the unit-cell constants of HoNiAl with other known examples of this structure type1' and from the density of HoNiAl, given in Table 11. The density indicated that three formula weights comprised a unit cell, as in the prototype compound Fe2P. The assignment of the three species to lattice sites was made initially on the basis of atomic size. The large holmium atoms were assigned to the 3(g) sites that have a relatively large interatomic distance to nearest neighbor positions, the small nickel

Jan 1, 1969

By R. E. Lund

Josephtown Smelter employs the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. The process uses resistance-type electric furnaces. Flow of current through the sintered ore and coke charge develops the energy required for smelting at the reaction sites. To produce zinc metal, the furnace off-Gases bubble through a large "U"-tube filled with molten zinc which condenses the zinc to liquid; the metal is then mechanically cast into slabs. To produce zinc oxide, the furnace vapors burn in air and the resultant powders are collected. The smelter comprises three distinct circuits. One circuit produces American Process zinc oxide and high grade metal; another circuit produces tailor-made alloys of controlled lead and cadmium content; the third circuit produces prime western zinc metal and feedstock which is refined into special High grade metal and French Process zinc oxide. The roasting circuit utilizes multiple-hearth furnaces for deleading the zinc concentrates; fluid bed and suspension roasters are employed for desulfurization. Sintering produces a hard, porous furnace feed. The flexible smelting process is adaptable to consuming various kinds of secondary material. Extensive residue treatment accomplishes high overall zinc recovery. Smelter by-products include sulfuric acid, cadmium, and mercury.

Jan 1, 1970

By J. D. Ridge

The geologic setting and mineral relationships of seven European massive sulfide deposits that more or less conform to the bedding of the largely noncal-careous sedimentary rocks and/or bedded volcanics in which they are found are considered here. These orebodies consist largely of massive beds or lenses of sulfides usually surrounded by halos of disseminated sulfides and distorted by tectonic activity. The formations containing these deposits have been metamorphosed in varying degrees at times subsequent to their lithification. The ore-forming process is thought to be essentially volcanic, with the ore constituents being brought to the shallow-water site of deposition through tectonic fissures from magma chambers at depth as gases or relatively concentrated hydrother-mal solutions. Certain European ore deposits of base metal sulfide have previously been considered to be of hydro-thermal or magmatic origin, but today a number of European mining geologists consider them to be syngenetically produced. In an effort to provide American geologists with some idea of the reasons behind this change in thought, the geological settings of seven of these deposits have been studied. These are: Ldkken, Meggen, Rammelsberg, Ergani-Maden, Outokumpu, Boliden and Roros. These deposits lie in bedded rocks that have undergone metamorphism from causes not universally agreed upon; most of the formations were originally shales, and may have been intercalated with limey and occasionally quartzitic beds, volcanic tuff, agglomerate, extrusive lavas and usually basic intrusives. Deposits of the conformable type, however, are not confined to these rock types but may be in calcareous and associated igneous rocks or almost entirely in volcanics. These deposits may be closely associated in space with igneous rocks that, again, are usually basic types. Although the ages of the enclosing rocks range from mid-Precambrian (Boliden and Outokumpu) to Eocene (Ergani-Maden), the bulk of them are Paleozoic, with two (Meggen, and eammelsberg) being upper middle Devonian and two (LØkken and RØros) being Cambro-Ordovician. Geographically, two are in West Germany, four in Scandanavia and one in Turkey. Of the seven deposits, six are mined for copper, with three of these also producing zinc, and two lead; one is mined for zinc and minor lead. In the discussions of the seven conformable deposits that follow, I have attempted to present as uniform a treatment as their varying characters will permit. For each deposit, I have considered the stratigraphy of the area, its major structural characteristics, the form of the orebodies, their mineral content, and the origin of the ore. In the last of these subdivisions, I have presented only the viewpoint of those who believe the ores to have been formed by syngenetic processes, processes that went on at the same time as those which produced the beds that enclose the ores but that are not, in the deposits in question, thought to have been sedimentary in the strict sense of the term. The materials of which these orebodies are composed, it is suggested, did actually collect by falling through sea water to the floor of that portion of the sea in which they accumulated. The ore constituents, however, are believed by a considerable number of European geologists to have been added to the sea water from intratelluric sources, probably igneous magma chambers, as exhalations — hydrothermal solutions or volcanic gases. The effect of the encounter with sea water on these ejected gases or water-rich vapors was to precipitate their potentially solid constituents with great rapidity; they were deposited so quickly, in fact, that the amounj of normally accumulated mechanical or chemical sediment deposited over the same period of time was essentially negligible. The ores formed in this manner, however, are generally interbedded with normal sediments or with lava flows, or with any combination of these two types of rock-forming materials. Such departures as these deposits may have from their original mineral content and attitude are thought to be directly related to the degree of dynamic or static metamorphism that they may have undergone after their accumulation. I have not attempted here to present alternate hypotheses to that of so-called exhalative sedimentation although, of course, such exist and, in my

Jan 1, 1963

By SAM YOUR

PROCESSING, technology and application of non- ferrous metals-copper, lead, zinc, aluminum, nickel, precious metals, foundry metallurgy, less common metals, secondary metals-are the special field of the Institute of Metals Division. New developments in this field during 1930 are more or less briefly out- lined in this review prepared by the papers and publications committee of the Institute of Metals Division as follows:

Jan 1, 1931

By Chas. B. Dudley

A Discussion of the papers of Mr. James Gayley, on "The Application of the Dry-Air Blast to the Manufacture of Iron," and of Mr. J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," by Messrs. Charles B. Dudley, R. W. Raymond, J. E. Johnson, Jr., William F. Mattes, James Gayley, David Baker, John Birkinbine and F. E. Bachman. (Washington Meeting, May, 1905.) CHAS. B. DUDLEY, Altoona, Pa.:-Pam not a blast-furnace man, and this always puts me it a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, " I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of water-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 18S5, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are for the moment interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satis¬factory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much simpler way, simply saturate the air at a constant temperature, and thus get uniform working and

Sep 1, 1905