Search Documents

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By AIME AIME

ON the headwaters of the Hudson Riser, in a sparsely populated area of the north woods at Tahawus, N. Y., thirty miles from the nearest railroad, is the Maclntyre property of National Lead Co. Operations involve the mining and processing of titaniferous iron ore to produce ilmenite concentrate, and magnetite concentrate containing vanadium, for use in the production of iron, titanium, and vanadium in the war program. Accordingly, Maclntyre at present is classed as a war plant. More than 3000 long tons of ore is ruined daily by opencut methods and treated in an ore concentrating plant.

Jan 1, 1943

By William P. Shinn

Jan 1, 1881

By O. H. Banes

The electrolytic zinc plant of the American Zinc Company located at Sauget, Illinois started operations in April 1941. The plant had a designed capacity of 45(T) per day. The original flow sheet was quite simple, incorporating the low density process. Through the years the capacity of the plant has been increased to the current design of 214(T) cathodes per day. This paper describes the current operation along with typical metallurgical data.

Jan 1, 1970

By Oliver Bowles, Carl A. Gnam

THE construction industry normally contributes extensively to the general economic welfare of all sections of the country. Billions of dollars are spent for materials and labor, and the success or failure of many business enterprises depends upon the volume of construction. The steel, aluminum, copper, cement, brick and tile, lime, gypsum, stone, sand and gravel, and several of the less prominent mineral industries are vitally concerned. Of great interest, therefore, is the accumulation of needed construction following the relative inactivity of the past five years, the recent moderate revival in building, and the prospect of a broader and more definite upturn. One may judge the magnitude of possible expenditure for construction by what has occurred in the past. The peak years were 1925 to 1928, inclusive, when the annual values of con- tracts awarded amounted to over six billion dollars. In marked contrast was the 1933 total of about 1% billion, the lowest level shown in the Federal Reserve Board Index, which goes back to 1919, and the more favorable 1935 figure of about 1.7 billion. An increase of nearly four billion over the 1935 volume would be necessary to equal the peak year 1928.

Jan 1, 1936

By DIFTIGIHT E. WOODBRIDGE

(Glen Summit Meeting, June, 1911,) DURING April, May, and June, 1910, I was in charge of an examination of the greater part of the Moa iron-ore area in Oriente Province, Cuba, on the north coast, near the east end of the island. My instructions, on arrival at the properties, were to check former estimates of tonnages and grades, and to re-examine the ore comprised in claims covering 44,727 acres. This work included .the running of lines dividing the properties into co-ordinate planes, the boring of many thousand feet of holes spaced at the intersections of these co-ordinates, the taking of samples of the ore penetrated, the analysis of these samples for their various constituent minerals, and the determination of the results as to tonnages, depths, and grades, both for individual properties and for the entire group. Each section of every one of the thousand holes drilled was to be compensated for depth and grade with every other, a series of simple arithmetical calculations of no slight magnitude, the mere mechanical labor of which consumed much time, but finally resulted in giving a complete average of all the essential facts for the entire area of 18,000 hectares. Had it not been for the more than willing, active, and able co-operation of the officers of the Spanish-American Iron Co., from Charles F. Rand, President, and Jennings S. Cox, General Manager, down to the most humble water-carrier, the work would have consumed far more time than it did. Papers prepared by others, and to which my present paper may be considered an addendum, elucidate, more fully than I could hope to do, the origin and geological character of these ores. I will confine myself to the situation, method and expense of exploration, and to probable courses of development and mining, with some attention to the cost of the ore delivered in the United States.

Mar 1, 1911

SME Membership Directory Listings of record March 31, 1072 SOCIETY OF MINING ENGINEERS OF AIME

Jan 7, 1972

By David J. Mack, Dennis R. O’Boyle

The mechanical properties of three polycrystalline intermediale Phases that have the y bvass structure were measured in compression between 400° and 900°K. At the lower testing temperatures— termed Region I— no plaslic deformalion occurred prior to brittle fracture. A1 higher temperatuves— lermed Region III—the three phases deformted plaslically for all strain rules from 1.5 to 36.0 x 10-4 sec-1. The homologous temperature for the inilialion of plaslic flow increased in the same order as tile atomic size difference between atoms in each plmse (0.50Tmp for y AgZn, 0.62Tmp for y CuZn, and 0.76 Tmp for y CuCd). The increased flow resistance oj. y CuCd above 0.50Tmp is explaitzed in terms of the more random arrangement of copper and cadmiwn atoms on the laltice sites of&apos; the y bvass slrilctlire. Plaslic deformation of the three intevmiediate phases in the smooth plaslic flow region appears to be controlled by oacancy-induced dislocation climb. RESULTS are reported in this paper on the mechanical properties of three binary intermediate phases having the complex cubic y brass structure (D82, 143m) containing fifty-two atoms in the unit cell. The structure of the prototype y brass phase, y CuZn, was first analyzed by Bradley and Thewlis&apos; based on the X-ray work of Westgren and Phragmen.2 The y brass structure can be visualized as an arrangement of twenty-seven body centered cubes (3 by 3 by 3) into a unit cell containing fifty-four atoms. From this cell the center atom and the four corner atoms are removed and the remaining fifty-two atoms are slightly displaced, resulting in the y brass structure. Approximately thirty-five binary intermediate phases that have an electron to atom ratio of 21:13 have been reported to form the y brass structure. The three y brass intermediate phases selected for this study are formed from elements in groups IB and IIB of the first and second long period. Each compound exists over a composition range that includes the stoi-chiometric composition A5BB (Cu5Zn8, Ag5Zn8, Cu5Cd8). y CuZn (a0 = 9.944A) has solubility limits extending from 57 to 67 at. pct Zn at 500°C apd melts peritecti-cally at 834°C; y AgZn (a0 = 9.326A) has a solubility range from 58 to 63 at. pct Za and melts peritectically at 661°C. y CuCd (a, = 9.596A) melts congruently at 563°C and has a maximum range of solubility extending from 58 to 64 at. pct Cd. In order to minimize coring and microporosity during solidification, the composi- tion of the compounds that form peritectically (y CuZn and y AgZn) was chosen so that the temperature difference between the liquidus and the solidus is only a few degrees centigrade. In selecting y brass compounds for this study, phases were avoided that contained a transition element or that had an electron to atom ratio greater than 1.70. Hume-Rothery et a1.3 has observed that, when the electron to atom ratio of y brass intermediate phases exceeds 1.70, atoms begin to drop out of the unit cell to maintain a constant electron to unit cell ratio. EXPERIMENTAL PROCEDURE Each of the three intermediate phases was prepared from elements having a purity >99.999 pct. Only trace quantities of impurities (<0.0001 pct) were detected by spectrographic analysis of the four elements. A master alloy of each compound weighing approximately 130 g was prepared by melting the elements in evacuated sealed quartz tubes heated in an electric furnace. Specimens having the desired diameter for the mechanical property measurements were obtained by remelting the master alloy in a Vycor tube under argon and drawing specimens from the melt into 4-mm-diam quartz tubes. To obtain a smooth surface on specimens drawn from the melt, the inside of the quartz tube was coated with a thin layer of graphite formed by thermally decompositing acetone. All specimens were imbedded in sealing wax and cut to the proper length with a diamond-impregnated cut-off wheel. The individual specimens (4 mm diam by 8 mm long) were then sealed in evacuated Pyrex tubes and homogenized at 500°C for 72 hr. Chemical composition, variations over the length of the rod (10 cm long) were generally less than 0.2 pct and the analyzed composition differed from the desired composition by less than 0.5 pct.4 Metallographic evaluation of the specimens after homogenization showed no evidence of a second phase in any of the compounds. The average grain size of the specimens after homogenization was 1 to 2 mm. All mechanical property measurements were carried out in an argon atmosphere using a compression apparatus described previously.5 Prior to applying the load to the specimen, the test apparatus was evacuated, back-filled with argon, and heated to the test temperature for 20 min to establish thermal equilibrium. EXPERIMENTAL RESULTS Mechanical properties measured as a function of temperature and strain rate for each of the three y brass phases were similar. From room temperature to the ductile-to-brittle transition temperature, only elastic deformation was observed prior to fracture.

Jan 1, 1968

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue&apos; back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.&apos; Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962

By M. Albertson

UNITED STATES petroleum pro-dU6tion during 1937 materially exceeded? that of any previous year. Firm control of the production rate was maintained under State and Federal laws and aided by the&apos; Interstate Compact. During the first ten months," crude oil prices were stable, except for a slight increase early in the year. Toward the end of the year, uncertainty of price structure be-came evident and a sharp reduction in allowable production was under way. Exploration for new pools and development of .pools already discovered continued active throughout the year. Production control agencies in Texas, and to a less extent in New Mexico and Louisiana, appear to have had increasing difficulty in holding crude oil output to allowable limits. The situation elsewhere is less well known but probably the same condition exists in other important producing States whether control is by State commissions or by unofficial bodies.

Jan 1, 1938

By N. N. Breyer

A specially built "hard" tensile machine with characteristics permitting the precise detertnination of the drop of the load at the yield point has been used to study the magnitude of the yield-point phenotnenon in prestrained martensitic 4340 steel. A new phenonzenon, the appearance of a secondary yield point, has been observed by holding the specimen at constant strain in the plastic region. Furthermore, it has been found that a series of yield-point drops could be introduced by successive constant strain holds in the plastic region. The isothermal kinetics of the development of the secondary yielding point lave been studied at four temperatures: 24° 0° -18°, and -79°C. From the results of the kinetic investigation, equations for the In a previous investigation1 it was shown that, contrary to generally held opinion, steels of medium carbon content, such as 4340, 4140, and 86B30, in the as-quenched martensitic condition, can be cold-drawn through a die with reductions in area of up to 10 pct without cracking. Tensile specimens of 4340 machined from bars quenched and prestrained in this manner exhibited tensile strengths of about 400,000 psi coupled with 30 pct reductions in area. In addition, it was found that each sample of such steels exhibited a yield point in the quenched, cold-drawn condition. Since these studies were conducted on a commercial hydraulic testing machine of a type which is not well-suited to detailed study of yield-point behavior, it was decided to study this phenomenon more thoroughly on a rigid straining machine. In this new investigation, use of such a "hard" machine not only allowed study of the magnitude of the yield-point drop but also revealed a new phenomenon—secondary yielding of the martensite introduced by stopping crosshead motion after plastic deformation of the sample had begun. The present paper is a report of these findings. MATERIALS AND PROCESSING The material used was a commercial 4340 steel of the composition shown below: 0.41 0.80 0.013 0.019 0.31 0.85 1.76 0.28 1 0.42 0.77 0.015 0.024 0.30 0.84 1.69 0.28 0.08 2 1 = Ladle analysis. 2 = Laboratory analysis. Bars of this steel were processed in the following way: 1) machined to predetermined diameters; 2) austenitized at 870°C for 1 1/2 hr; 3) oil-quenched; 4) cooled to -115°C for 1/2 hr; onset and increase in magnitude of the secondary yielding in this temperature region have been found to fit the relationship ?Ys = Atn where ?Ys is the magnitude of the secondary yield Point in psi, t is the time in seconds, and A and n are parameter characteris-tics of the material. Although the occurrence of the primary and secondary yield points could be rationalized qualitatively on the basis of stress-induced ordering of carbon atoms in the stress fields of dislocations, as postulated in an earlier paper, the kinetics of the secondary-yield-point development were interpreted to indicate that the ordering involves more than just single jumps of carbon atoms from high-energy to neighboring low-energy sites. 5) pickled and lime-coated; 6) drawn through a carbide die. The predetermined diameters were chosen so that drawing through the same die gave the various reductions desired. Tensile specimens of 0.252 in. diam with a 1 1/4 in. gage length were then prepared from the drawn bars and tested. In order to study the stress-strain behavior at the yield point in detail, a rigid tensile machine with a high spring constant was constructed. Columns of large cross section (relative to the specimen cross section) constituted the machine frame. A dc motor was used to drive a screw via a gear reducing train and a "crane" thrust bearing. In this relatively simple device small deformations could be observed un-blurred by the slow response and lower spring constant inherent in hydraulic machines.&apos; A strain-gage dynamometer permitted load changes as small as 8 lb to be read. RESULTS Tensile test samples machined from bars in the as-quenched condition with no subsequent drawing and samples from bars with 3.8 pct reduction after quenching gave stress-strain curves typified by those shown in Figs. I and 2. The time lapse between predrawing and tensile testing varied but usually ranged between 3 to 6 days at room temperature. The strain rate during testing was 0.003 in. per in. per min. The as-quenched curve is seen to have a broad serrated maximum whereas the stress on the specimen prestrained 3.8 pct rose linearly to point A, Fig. 2, fell abruptly to B, and then gradually to C. The abrupt drop to B was accompanied by evidence of incipient necking. The drop of the stress at the yield point in the prestrained samples (A to B in Fig. 2) changed with the percent prestrain, as illustrated on Fig. 3. Although the tensile strength increased continuously with the amount of previous cold drawing, the magnitude of the yield point drop first increased—up to about 6 pct prior reduction—and then decreased. Specimens from bars predrawn more than 8 pct broke in a brittle fashion in the elastic portion of the stress-strain curve.

Jan 1, 1967

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleysl and Gathmann,2 who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1951

I HIT the ceiling when I opened my November MINING ENGINEERING and after waiting a week to cool off I&apos; still find it necessary to express my resentment of the gross libel embodied in the editorial introduction to Norman Stines&apos; legitimate criticism of my paper on "Russia&apos;s Mineral Potential" (p. 949). The underlying thesis of my article, and a point that I tried to make even more clearly in my oral presentation at the St. Louis meeting last February, is that we should not over estimate the present and near-future mineral production of the USSR. The words that I resent in your boxed introduction are: "Opinions range from those presented by Paul Tyler ... to those of Norman C. Stines . . ." This is not merely an understatement that can be defended by admitting that the range goes much farther to the left, beyond me. It represents the appraisal that 90 pct of your members will carry away, namely that I am not only an incompetent observer-which may be true-but always that my bias is to applaud the efficiency of the beasts in the Kremlin-which is not true. Notwithstanding my efforts to clarify the record I now find myself branded as being at the opposite pole from &apos;Mr. Stines among the red-eyed worshipers of Communism or at least among the timid souls that shake in their boots in the belief that the Soviet system has created an invincible as well as an evil menace to the decent peoples of the world. My ideas are somewhere in the middle ground between Mr. Stines&apos; complaisance or contempt and the exaggerated fears of several other observers whose views have received wide acceptance. PAUL M. TYLER MINERAL TECHNOLOGIST & ECONOMIST 5005 EDGEMOOR LANE, BETHESDA, MD. The introductory paragraph to Mr. Stines&apos; criticism of Mr. Tyler&apos;s article (Russia&apos;s Mineral Potential, June issue MINING ENGINEERING, page 494) is erroneous as pointed out in author Tyler&apos;s letter above. In his article he objectively presented an estimate of the mineral position of the Soviet based on the statistics available to him which sources are credited in the first paragraph of his article. We happen to know that, Mr. Tyler was reluctant to prepare the article for the Mineral Economics Division sessions at the 1951 Annual Meeting and did so only because of his loyalty to AIME. It was thought that this article would be a basis for discussion of this important subject at the Annual Meeting. We apologize to Mr. Tyler for any embarrassment our introduction, may have caused him. Editor

Jan 1, 1952

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By J. P. Doan, G. Ansel

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By G. Ansel, J. P. Doan

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By Harlowe Hardinge, R. C. Ferguson

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year&apos;s time.

Jan 1, 1950

By Lyon F. Terry

SPEED-UP of production of crude oil and its products, accompanied by rising prices and the organization of the industry on a war basis, featured the economic aspects of petroleum in 1941. Early in the year American tankers were urgently requested by the British to replace losses and offset slower transit under convoy. Some forty American owned tankers were first assigned to Britain and an additional forty-odd ships were transferred during the summer. This threatened to reduce our transportation facilities from Gulf ports to the Eastern seaboard below requirements, especially should sinkings have increased and the British needed more ships. Co-ordinator Ickes began preparations for restricting gasoline consumption in the Eastern district and plans were formulated for the construction of an emergency trunk pipe line from Texas to New York and Philadelphia refining centers, and for a gigantic tanker-building program. Sales of new oil-heating units in the East practically ceased. The companies were urged to transport as much oil as possible by tank car and by October 140,000 barrels of oil per day were reaching the East Coast district by rail, sufficient to meet 8 per cent of total requirements. But British sinkings from July through October decreased 63 per cent compared with the four months ended June 30, Britain began the return of tankers, the construction plans were dropped, and the threatened shortage was thus averted.

Jan 1, 1942

By A. STEPHENSON

EXPERIMENTAL work conducted at the Petroleum Engineering Laboratory of the University of California by L. C. Uren, J. Domercq, Jr., and J. Mejia has shown that small diameter wells offer tremendous resistance to the flow of fluids in their immediate vicinity. This resistance is due in part to the constriction of the area through which the fluids must pass as they approach the wall of the well, but is also accentuated by the increased volume which results from gas expansion. The latter in turn is a function of the deduction in pressure, the fundamental cause of fluid movement. If the diameter of the bore is enlarged several diameters, the capacity of the well, or the volume of fluid passing per unit drop in pressure per unit of time, is greatly increased without necessitating such high fluid velocities. The fundamental features which should be taken into consideration in the design of casing joints were stressed by J. B. Graham and E. E. Smith. These involved such points as correct thread design, high efficiency, and small diameter, together with the insurance that leakage will absolutely be prevented. The practical features of such design were ably discussed by engineers from leading steel manufacturers.

Jan 1, 1935