Search Documents

By Charles Sóstenes Assunção

A mathematical model of heat transfer and solidification for a continuous casting of round billets was developed. The water flux density of the secondary cooling zone was experimentally measured, using an apparatus in industrial scale with two types of nozzles, flat jet and full cone jet. The profiles of water distribution were applied on the mathematical model. The results showed that the water distribution is not uniform in both longitudinal and angular directions owing to the unevenness of the spray and to the curvature effect of the round billet. This non-uniformity causes important variation of the heat transfer coefficients and superficial temperature of the billet, especially in the first cooling zones, where the temperature is higher. The mathematical model was used to simulate a change of nozzle type in the first cooling zone. The results showed that the heat flux and superficial temperature variations were reduced with a full cone jet nozzle in comparison with the flat jet nozzles.

Aug 16, 2017

By Adriano Alex de Almeida

Dois aços de grão não orientado com 2,45 e 3,3 %Si com 7 amostras para cada liga, foram estudados para compreensão do efeito do teor de silício nas perdas histeréticas. As amostras foram recozidas com diferentes temperaturas de recozimento final, resultando em diferentes tamanhos de grão. As perdas histeréticas e B50 foram medidos. Os resultados de B50 mostraram que não houve variação de textura entre as ligas com diferentes %Si. Por fim, os resultados não mostraram variações da energia dissipada pela perda histerética com adição de %Si.

Aug 7, 2018

By Elton Douglas Heriger Pereira

Refratários de alta alumina apresentam boa refratariedade, elevada resistência mecânica em altas temperaturas, boa resistência à variação bruscas de temperatura sem se romper sendo utilizados em revestimento de panelas e válvulas siderúrgicas devido sua propriedade anfótero e ter aplicações sobre à ação de escórias básicas. Neste trabalho procurou-se avaliar o efeito de adições de 1,5; 3,0 e 4,5%p. de Nb2O5 em refratário de alta alumina, estes obtidos a partir de uma mistura de diversos tipos de alumina, 5,0 %p. ZrO2 nanométrica (TZ-8Y) e agregado de mulita, sinterizados em temperaturas de 1400 e 1600 °C. Como nestes refratários a ZrO2 não surte o efeito de microtrincamento, a formação de fase vítrea a partir de Nb2O5 e a incorporação de agregados ao refratário foram fundamentais nas propriedades obtidas. Foram avaliadas propriedades tecnológicas como densidade e porosidade aparente pelo método de Arquimedes, formação de fases por difração de raios-X e análise microestrutural por microscopia eletrônica de varredura e resistência ao choque térmico.

Oct 30, 2017

By Xiaowei Du, Xitao Wang, Xuekun Shang

The deformation behaviors under both tensile and compressive forces and microstructure evolutions of cast SA508-4N steel were investigated at elevated temperatures. True stress-strain data were obtained from hot deformation experiments performed on a Gleeble-3500 thermal-simulator under different temperatures (750-1200C) and strain rates (0.001-10 s-1). The reduction of area decreases as a function of temperature from 750C to 900C and then increases. At 1200C, the reduction of area reaches more than 99% with the strain rates of 0.5 s-1 and 1.0 s-1. The dynamic recrystallization under compressive stress occurs at 800C under low strain rate and a complete dynamic recrystallization can be observed when the temperature reaches above 1100C. A “two-stage” flow stress constitutive model concerned with dynamic recovery and dynamic recrystallization was established based on the true stress-strain data. This model shows good agreement with experiment results. Moreover, we developed a dynamic recrystallized grain size model to describe the average grain size after complete dynamic recrystallization.

Oct 1, 2019

By Kermit Reins

The most recent modernization phase of the wire rod mill at Sterling Steel involved installation of a pre-finishing mill, using a Morgan Vee Mini-Block, a new water box and shear with utility systems and automation. The new mill configuration adds more stands to the mill for better drafting and is designed to improve finished product quality by providing a more uniform entry temperature, better control of the feed section into the No-Twist® mill as well as enhanced surface quality. The new shear improves cut length accuracy as well as decreases the amount of trimming to reduce yield loss. This paper explains the changes made in the mill and the features of the new equipment and automation.

Aug 17, 2017

By Claude Bodeving

The present steel economy drastically increases the financial strain on blast furnace operators. As a consequence, the importance of reliable cast floor operations is increasing drastically, which has a direct influence on the required clay mass and tapping equipment performances. When using modern high performance clay masses, pneumatic taphole drilling machines quickly reach their performance limits, which has made fully hydraulic drill hammers a standard in modern cast house operation. Besides the well-established hydraulic TMT hammers with high impact energy, an alternative version with lower impact energy, but high impact frequency was developed by TMT in the past, in order to achieve improved taphole protection. TMT’s recent research has shown that the drilling requirements inflicted by the taphole condition change over the taphole length, which has triggered the development of a new hammer, capable of switching between a high impact frequency mode and a high impact energy mode.

Aug 17, 2017

By Afonso Cardoso da Silva, Romeu Thomaz Viana Jr, Emanuelle Garcia Reis, José Herbert Dolabela da Silveira

The Gerdau Ouro Branco Mill, three years after the implementation of its new plate mill, has started to develop high complexity products. The plate mill’s learning curve has been increasingly challenging since products are being developed to their highest grades. This work aims to present the first results of the development of steels of the strength class of 510 MPa produced by TMCP (Thermomechanical Controlled Processing) followed by accelerated cooling. These results show the potential and advantage of the accelerated cooling process regarding to obtain products of high mechanical strength and high toughness, associated with a low equivalent carbon.

Oct 1, 2019

By Priscilla Pessin Coppo

The prevention of dental enamel wear has particular relevance for preventive and restorative purposes in dentistry. The wear damage can increase due to salivary disorders and/or parafunction (bruxism); antagonists incisal surfaces become flat and coincident. This study aims to investigate the wear behavior and the related mechanisms in sliding pairs of conformal incisal enamel, with similar values of hardness and fracture toughness, with different applied normal loads and lubricated conditions. Bovine incisors, under pin on flat configuration, were tested in two lubrication condition (dry or with natural saliva) and two applied normal loads (8 and 16 N). The worn surfaces were investigated by 3D profilometry and SEM. The analysis of worn surfaces indicated mechanisms of brittle fracture, but with different severities. Under a normal load of 16 N and dry condition, wear is controlled by a brittle process: microcracking with flake-like wear particles, which results in high friction coefficient (> 0.85), wear rate and wear volume. On the other hand, under a normal load of 8 N and natural saliva, wear took place in the interprismatic region, with consequent exposure of prisms and fracture in localized regions. In this case, the friction coefficient was 16% lower and the wear volume was one order of magnitude lower. Under 8 N and natural saliva, the wear was greater than in the dry condition, probably due to tribochemical reactions.

Jul 31, 2018

By Renan Bueno Wojciechowski, Yukio Shigaki

The quality of flat rolling process depends highly on multiple factors such as applied forces, materials involved for both strip and rolls, roll geometry and its positioning. To calculate the strip shape, a mathematical/numerical model can be applied, showing the final product and how the equipment behaves when changing some parameters. This is usually a time-consuming task for both user and computer, especially when it involves thin and hard strips. By coupling a quick rolling load calculation method as Bland-Ford and Finite Element Method (FEM) for roll stack deformation, it is possible to create an accurate and user-friendly rolling simulator. This paper presents the improvements done in the 3D FEM/multi-slab method and its actual capabilities by simulating two cases of a 6-High rolling mill. Different analysis in this equipment can be easily done in about 10 minutes by using the developed an electronic spreadsheet program interface and the folder generated with relevant results and logs. An operation manual and a commercial FE program plugins were made to aid construction of a completely new model. The code was created in a modularized way to assist the application of this simulator for other operational conditions.

Oct 1, 2019

By Maurizio Massimo

Danieli developed the “3Q” suite of process control technologies to address three critical principles: delivering the highest product Quality, in the required Quantity, with Quickness of response required for today’s casting machines. Ever increasing market demands for productivity and slab quality necessitate the latest advances/improvements in equipment design, process technology, and control software for all types of slab casters, and Danieli boasts a unique experience that extends from ultra high-speed thin slab casters to extra high-thickness conventional slab casters. The “3Q” system is monitored and controlled by a unique, intelligent HMI incorporating. Touch screen technology and Operator Assistant tablets. Operator Assistant is a tablet based system that guides the operator through the plant process, so that in the event of a process change or an alarm the operator is automatically presented with the choice of possible solutions / actions. The comprehensive range of technological packages cover all aspects of caster design and automation control, from feeding of liquid steel into the tundish to the final slab leaving the caster.

Aug 17, 2017

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Emanuele Osto

In late 2013, the installation of the world's first application of a break-through technology for rail hardening was started at Baogang Iron & Steel (Group) Co. Ltd. in Inner Mongolia, China, one of world's leading rail producers. The "Injector Dualphase Rail Hardening" (idRHa+) system was developed by Primetals Technologies and Centro Sviluppo Materiali S.p.A. (RINA-CSM) a Technical Center headquartered in Rome, Italy. Baogang was a key partner, providing its large expertise of premiumrail producer, including its experience with existing offline technologies. With a design based on thermal, mechanical and metallurgical models, idRHa+ can apply customized cooling protocols, so to obtain the desired microstructure and hardness distribution across the rail head, with a high degree of accurateness and operation flexibility. idRHa+ can be installed in inline or offline configurations. During 2014, the system was successfully commissioned at rail mill #2 in the city of Baotou, Inner Mongolia, and entered the regular commercial production. This paper gives an overview of the key concepts behind idRHa+'s design, the progression of its commissioning and testing till the ramp-up to consistent industrial operation. Derived from idRHa+ research and experience, other water-cooling technologies are available for different applications such as: quenching & tempering of medium-large sections, control of distorsion of merchant bars, quenching of stainless grades for improving the resistance to corrosion.

Aug 16, 2017

By Maria Auxiliadora Mendes Aguiar

O sistema de flotação de minério de ferro consagrado no Brasil desde 1977 é a flotação catiônica reversa, na qual deprimem-se os minerais-minério de ferro e flota-se a ganga silicática. Em termos de reagentes, o amido é utilizado como depressor de minerais de ferro e a amina como coletor de quartzo e espumante. Teoricamente, espera-se que o aumento da dosagem de amina eleve a flotabilidade do quartzo. Entretanto, a realidade industrial tem mostrado um comportamento contrário. Este fato tem sido explicado pela formação de clatratos - termo utilizado para denominar o composto molecular formado pela adesão das moléculas de amina no interior das moléculas de amido, que resulta na depressão do quartzo. Em laboratório, a avaliação da flotabilidade de minerais puros pode ser feita através de ensaios de microflotação em tubo de Hallimond modificado. O objetivo do presente trabalho é verificar a flotabilidade do quartzo utilizando-se diferentes dosagens de amina e amido. Para isso, ensaios de microflotação em tubo de Hallimond modificado foram realizados em faixa de pH entre 6 e 12. Identificou-se a dosagem de reagentes que favoreceu a formação dos clatratos.

Aug 1, 2018

By Johan Richaud

Achieving high surface quality steel in the continuous casting process requires optimal mould level control. The design of the casting channel from the tundish to the mould is crucial to prevent formation of undesired instabilities or biased flows that can cause level fluctuation. With the aid of CFD and with physical water models, the geometry of the stopper nose and the nozzle seat have been studied and optimized to improve the overall mould flow stability. A special stopper nose; Ripple Stopper (RST), has been developed that reduces the formation of large and unwanted eddies in the liquid steel that destabilize the port exiting jets. Instead, the RST produces a fast release of turbulence in the form of a large number of small eddies. The large sudden fluctuations in the mould level are reduced, which in turn reduces the occurrence of surface defects. An additional benefit is derived from the local pressure around the stopper nose region being greater which reduces the refractory erosion. For a tundish gate type flow regulation, a new design encompasses an offset in the Tundish Well Nozzle (TWN) that realigns the flow and reduces the bias flow that is common to tundish gate regulation. The steel recirculation regions below the throttling gate are decreased reducing the risk of oxide depositions. The RST and the Offset bore casting channel have been applied successfully leading to a superior flow control performance between the tundish and the mould.

Jul 30, 2018

By Flávio Beneduce Neto

As trincas a quente ou de solidificação em peças micro-fundidas em superligas a base de níquel podem ser um item importante no índice de perdas em componentes específicos. O aparecimento desse defeito está ligado fundamentalmente à quantidade de líquido interdentrítico nos últimos estágios da solidificação e, principalmente, ligado à composição química desse líquido. Há duas ligas amplamente utilizadas na produção de rotores para turbo-compressores ou turbinas para a geração de energia: o Inconel 713C e o Inconel 713LC. A diferença entre estas duas ligas é essencialmente o teor de carbono. Curiosamente, a liga LC tem uma maior tendência ao aparecimento de trincas de solidificação. O presente trabalho procura identificar as diferenças de comportamento na solidificação dessas duas ligas através da termodinâmica computacional e ligar essas diferenças no aparecimento das trincas. Os resultados indicaram que os teores de Zr e Nb do líquido remanescente da solidificação são muito superiores na liga LC causados pelo atraso na precipitação dos carbonetos tipo MC nessa região que deve ser a fase que aumenta a resistência mecânica da área. O correto balanceamento da composição química da liga em relação aos elementos citados permitiu que o índice de perdas por trincas de solidificação caísse para níveis próximos a zero.

Aug 8, 2018

By Alim Ullah

The paper discusses the necessity of upgrading low-iron containing ores, giving as an example, NML-Tata Steel Project in the Quebec-Labrador region of Canada. As cooling of pellets is generally a bottle-neck in most pelletizing plants, examples are given of the methods used to improve cooling in the existing plants and a simple, low-cost alternative, tested on a pot-grate system, is presented. The procedure described is applicable to sinter plants also. The trends in iron and steel production worldwide are then given, as well as the reasons for the increase in steel production by the Electric Arc Furnace (EAF) route. The stoichiometric and thermodynamic requirements for producing iron, irrespective of the process, are explained. The different ironmaking processes, especially the Direct Reduction (DR) ones are briefly discussed, outlining recent improvements made to some of them. The pros and cons of producing cooled DRI and Hot-Briquetted Iron (HBI) are given with predictions made for their future growth. An alternative to cold-briquetting of DRI fines is also discussed. Highlights of an ironmaking processes which is at the laboratory/pilot plant stage are given.

Aug 1, 2018

By Alessandra Spaghetti

Rolling small-diameter hot wire rods at high speeds with conventional laying head pipes can wear the pipe out frequently and affect quality and consistency in the final product. Laying head upgrades using Sandvik SAF2507LHP™ (UNS S32750) tubes make possible to achieve optimal metallurgical properties, smooth coil formation and easier coil handling. Operators can also avoid unwelcome shutdowns due to frequent worn pipe changes and turndowns. Sandvik have been developing different customers and understand their process needs. The suitable selection materials that are able to withstand high levels of wear better than low alloy and carbon steel grades that are commonly used in industry is very important to improve the quality and increase productivity. UNS S32750 tubes were demonstrably superior to low alloy and carbon steels when used in Laying Head Pipe system regarding tubes lifetime, reducing replacement, production interruptions and increasing reliability.

Aug 17, 2017

By Bernardo Siqueira

This paper presents a unique stirred milling technology, Outotec HIGmill™, a modern, flexible and energy efficient grinding solution for fine and ultra fine grinding being tested in an industrial scale level. The test was performed at an iron ore pellet producing plant in Sweden (for confidentiality reasons, it will be referred to only as “the client”) where a pilot HIGmill™ unit (HIG25) was installed parallel to a conventional regrind circuit to compare its performance to the existing ball mill. By using a continuous test run procedure and evaluating the parameters of F80, P80, mill shaft rotation speed and power drawn it was determined its grinding capabilities, operational flexibility and energy efficiency. Outotec HIGmill™ outperformed the existing ball mill in the plant proving its capabilities to grinding finer, with steeper particle size distribution (PSD) and much higher energy efficiency. The tests performed showed that, with further refining of its operation, it is capable of consistently deliver the required PSD with up to 30% higher grinding efficiency.

Aug 16, 2017

By Carlos Vinícius Domingos de Carvalho

As perdas geradas nos processos de uma Aciaria contribuem de forma significativa para a perda metálica do processo. Eventualmente, mesmo com uma operação correta, do ponto de vista de características do produto, pode ocorrer comprometimento do ponto de vista econômico, e uma forma de redução direta dos custos e aumento de performance é a redução das perdas geradas no processo. Desta forma, tornou-se importante realizar um estudo para reduzir as perdas metálicas na Aciaria. Foi utilizado a metodologia Seis Sigma, sendo estratificadas as perdas por processo na Aciaria, onde as maiores perdas na rota dos processos de Lingotamentos Contínuos foram: perda no Distribuidor (24,7%), corte de sequência (17,5 %), retorno de corrida por baixa temperatura do aço na panela (16,3 %); perda por obstrução da válvula da panela (8,8 %). A perda metálica foi reduzida em 50,8%. Além da redução expressiva das perdas, houve uma grande contribuição em relação à compreensão dos modos de falhas para apropriação correta das perdas, tornando as informações mais seguras e facilitando o tratamento de possíveis falhas no processo.

Oct 30, 2017