Search Documents

By L. Rodd, C. Walker, T. Koehler

"The energy content of slag represents approximately 80% of the total energy inputs to a laterite nickel electric smelting furnace. Conventional slag handling methods produce only low grade heat and the entire thermal content of the slag is wasted. A heat recovery system proven on BOF slag in the mid 1980's can be adapted to a laterite nickel rotary kiln electric furnace (RKEF) plant. Slag is granulated using a high velocity air jet inside a waste heat boiler to produce slag granules. Granules are cooled during flight via radiation to water-cooled boiler walls and by convection to the granulation air. This system has the potential to recover 80% of the total slag energy in the form of hot air and steam.Integration of the recovered slag energy into the RKEF smelter can be achieved by a number of methods, including the use of preheated air at the ore dryers, kiln or existing power plant. Energy from the slag boiler may be used to reheat boiler feed water from the power plant or to produce superheated steam and generate electricity. The heat recovery system can provide up to 25 - 30% of the total electrical requirement of each RKEF line and a reduction in CO2 emissions of 234,000 tonnes per year.The total cost of slag heat recovery, including CAPEX and OPEX, is $2.5/GJ, which is competitive with using coal when CO2 credits are $18 per tonne. With Clean Development Mechanism (CDM) carbon credits currently selling at €13 ($20 USD) per tonne CO2, there is considerable opportunity for slag producers in regions including South America, Korea, Indonesia and Africa. Increasing fuel costs and more wide-spread legislation for GHG emissions will likely create conditions in which slag heat recovery could generate a favourable return on investment."

Jan 1, 2010

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By Franklin J. Stermole

INTRODUCTION Economic evaluation of an open pit mine is similar to the economic analysis of any major investment project in any industry. It requires (1) taking into account all of the costs and revenues that are estimated to be incurred over the economic life of the project; (2) crediting the project with all the tax savings and tax credits that will be realized over the project life from tax deductions and credits related to various project costs; (3) charging the project with all taxes to be paid on taxable income over the project life; and (4) properly accounting for the time value of money for all project costs, revenues, taxes, tax savings, and tax credits when making the overall project economic evaluation. These considerations must be taken into account for any valid method of economic analysis such as discounted cash flow rate of return (DCFROR) or net present value (NPV) analyses. All economic analyses fall into one of two categories. ( 1 ) comparison of income-producing alternatives, or (2) comparison of service-producing alternatives. The analysis of alternatives in either of these categories can be made by using correctly any of five basic economic evaluation approaches which are. ( 1 ) present value, annual value, (3) future value, (4) rate of return (ROR) , and (5 ) break-even analysis. Of these evaluation techniques, DCFROR and NPV analyses are used most widely for evaluating income-producing alternatives while present worth cost and equivalent annual cost analyses are used most often for the evaluation of service-producing alternatives. In this chapter income- producing alternative analysis is emphasized, so DCF- ROR and NPV are utilized for evaluating the case studies presented.

Jan 1, 1979

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By Herbert A. Everest

Discussion of the paper of HERBERT A. EVEREST presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 165 to 167. NEWELL G. ALFORD, Earlington, Ky. (communication to the Sec-retary*).-Mr. Everest's statement concerning the economies in a small coal mine has interested me very much. The majority of discussions on coal-mine economy omit the small operator and for this reason Mr. Everest's paper should lead to productive thought. I agree that close concentration of working places and constructive supervision of labor are two items of salvation to the small operator. It is also true that small mines often yield as much profit per capital invested as their larger neighbors. Mr. Everest also says that the small operator has so keen a regard for the inroad on his profits that even one extra day hand is an extravagance not tolerated, and this is rightly so. But, does not this earmark of the small operator in many cases offer a clue to his vital weakness? A credit balance is the acid test of success in any enterprise. With the small operator who owns practically all the capital stock this is particularly significant. He never takes his eyes off the market price and at the same time strains every nerve to cut down his payroll. In several cases I have noted that the resultant close supervision of labor was in fact too close. The "stitch in time" was not applied to the repair of this or that, with a decided increase to the cost of the work when it had to be done at the expense of cutting off the run when orders were on the books.

Jan 5, 1916

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The separation of fine mineral particles, especially using environmentally friendly approaches, is one of the main problems in the processing of low-grade ores and the re-processing of mining tailings. This work assesses the potential of biosurfactants as collectors in the flotation of ultrafine (smaller than 20 μm) particles of hematite and malachite. As biosurfactants, we test acetylated acidic (ac-ASL) and lactonic sophorolipids (ac-LSL). In addition, n-dodecyl-β-D-maltoside (DDM) is used as a model non-ionic alkyl disaccharide surfactant, and sodium oleate (NaOl) is used as a reference. The biosurfactants are characterized using surface tension and foam analysis. The interaction of the minerals with the surfactants is characterized using zeta potential, solubility, and single-mineral flotation. The collecting properties of the surfactants are compared for the ultrafine (− 20 μm) and coarser (38–90 μm) particle size in the two-mineral flotation of hematite and malachite against quartz. The ultrafine particle size improves the grade in the oleate flotation of hematite, as well as the grades in the DDM flotation of hematite and malachite, which is explained by the weak interactions of the metal oxides with fatty acids and DDM. At the same time, the flotation with ac-LSL and ac-ASL is highly tolerant to the ultrafine particle size. These results indicate that biosurfactants are an interesting alternative to conventional petroleum-based surfactants in the flotation of Fe and Cu oxides. Moreover, a proper selection of surfactants can help combat the problem of fines.

Feb 23, 2023

RECENTLY, we were asked to name the greatest contribution to progress in mining technology during the past 25 years. Immediately, the introduction of the pneumatic hammer for making blastholes came to mind because it can be credited with speeding the excavation of rock and the elimination of hand drilling. Possibly this answer was so spontaneous because we were working on this "drilling issue" Of MINING ENGINEERING. Present drilling tools have devel¬oped so rapidly, that a great deal of engineering is. required in the selection of bits, steel, and machines for the drilling conditions at each mine. Formerly a modicum of engineering was utilized in selection of equipment for it was purchased from manufacturer preference. With the development of alloy drill steels, tungsten-carbide bits, throwaway bits, and the jackleg drill, mining companies began doing more experimental work before making selections. It is unfortunately true, that each operator must begin at the beginning by doing his own test work before choosing his drilling method, and tools. Some of this work has been done very well-under controlled conditions and obtaining proper data on the variables. Such data should be accumulated from the various mines, tabulated, and published. Such a volume would be of tremendous help to the small operator in selecting equipment and would permit the research departments of the larger companies to formulate some measure of rock drillability and to undertake more specialized research on the different phases of drilling.

Jan 1, 1952

By Thomas T., Read

E DUCATION for the mineral industry was at first a single comprehensive curriculum, but it was early recognized that the main basis of mining is physics, while that of metallurgy is chemistry. The first school to offer curricula leading to degrees in mineral industry education in the United States (1853) had separate ones in mining and metallurgy. The Columbia School of Mines (the first really successful one) had only a single curriculum when it opened in 1864, but within a few years had so reorganized its work that it offered curricula in mining, metallurgy, geology, chemistry, and civil engineering. Interest in the metallurgy or geology curricula was slight at first, and for the next 30 years the great majority of Columbia students took the mining curriculum, probably partly because it contained nearly as much geology as the geology curriculum, practically all the metallurgy, and most of the chemistry, and partly because of the degree awarded for it. Other schools kept their mining curricula equally broad, and as late as 1900-1910 men were graduating as mining engineers who were practically as well prepared to make geology or metallurgy their life work, as they were for mining. Gradually, however, the subject matter of mining geology and metallurgy became so enriched through research and development that separate curricula in them became worth while; their progressive development is the subject of another chapter. Mining curricula also began to be somewhat diversified, and schools in areas where coal mining was of outstanding importance began to offer options in coal mining, the earlier curricula having been chiefly aimed at metal mining. The petroleum industry began its meteoric rise about the same time as mineral instruction in this country, but little more of applied science attended its birth than had attended such ancient practical arts as copper and iron

Jan 1, 1941

By D. D. Hogarth

"Edward Haycock, Engineer and Public Contractor Edward Haycock was born in Shrewsbury, England, June 14, 1813. His father was John Haycock, a timber merchant and soap manufacturer, residing at Swan Hill Court, Shrewsbury, and his mother Esther was the daughter of William Hilton of Hempstead, Hertfordshire. Edward's paternal grandfather, John Hiram Haycock, was the first of a line of architects that ""changed the face of Shrewsbury"" and ""provided some of the best examples of typical Victorian architecture in Shropshire""(1). Nothing is known of Edward's early life or education, although it appears that he made no attempt to follow this artistic trend. In 1833, Edward immigrated to Canada. The following year, he married Mary Butler, daughter of Johnson Butler, a Lieutenant-Colonel in the Lincoln Militia during the War of 1812. Mrs. Haycock, as co-heiress of Johnson Butler's estate, was assigned 600 choice acres of farmland in Brooke Township near present-day Sarnia. This alone would have guaranteed a tidy income, but the Haycocks soon disposed of this land, the last lots being sold in May 1840. Instead, Haycock turned his hand to engineering and, for a number of years, was employed by the Great Western Railway first in Woodstock and later in Hamilton. He then moved to Port Hope, tried farming, worked in the engineering office of the Port Hope, Lindsay and Beaverton Railway Company, and later constructed a portion of this railway(2). During his stay in Port Hope, Haycock met his future partners Ralph Jones, a contractor, and Thomas Curtis Clarke, chief engineer with the P.H.L. and B. Railway Company. The alliance was styled Jones, Haycock and Company and their most successful venture was the construction of the Government Buildings in Ottawa. This work was the crowning achievement of Haycock's career and, no doubt, his proudest moment was at 11:30 a.m., April 2, 1860, when his daughter Mary Emily, then a little girl of 4, with a special silver trowel ceremoniously laid the first stone. Of special interest in this project were the quarrying operations, which introduced Haycock to the art and difficulties of mining as well as to the potential returns of mines. Sandstone, for facing, was drawn from four quarries, 10 to 12 miles from the Departmental Buildings. Haycock seems to have been in charge of these operations, which in the early stages involved an average labour force of 86 men and 43 teams. However, by 1861, quarrying had declined in importance and the contractors were able to concentrate whole-heartedly on the construction site."

Jan 1, 1999

By Ari Jokilaakso, Junjie Shi, Zhuo Chen, Pekka Taskinen, Xiang Gao

The amount of copper flash smelting slag has increased during the recent years along with an increasing slag-to-metal ratio. During slag tapping, some copper sulfide is mechanically entrained. As a result, it is necessary to recover copper matte from the slag by suitable methods. At present, the most common way is slow, controlled cooling in a transfer ladle. However, research on the detailed effects of slow cooling and the function of slag modification is rare. This paper described experiments that were performed at different cooling rates (0.5, 1.5, 3, and 7 °C/min), with and without additive. A detailed characterization of the copper-rich phase and its particle size was subsequentlymade using SEM-EDSmicrographs and image analysis software.With a decrease in cooling rate, the particle size of the copper-rich matte phase became larger. The addition of gypsum and carbon as a slag modifier affected the size of the copper-rich phase slightly, and its chemical composition was modified compared with the experiments without additive.

Jul 31, 2020

By A. A. Smith, J. S. Smart

NUMEROUS investigations of the effects of the various impurities common to commercial coppers have been published, and the data have found wide use in industry. Naturally, emphasis has been placed on the oxygen-bearing coppers of the tough-pitch variety, but need is now evident for data covering the oxygen-free condition as well. Furthermore, relatively few of the important reactions between oxygen and the various impurities are well understood, and often the data at hand are not applicable to the low concentrations encountered in commercial coppers. This paper presents the changes in conductivity and softening temperature derived from individual additions of the group VIII triad, iron, cobalt and nickel, to high-purity copper, and constitutes a portion of the copper-research program being conducted at the Central Research Laboratory of the American Smelting and Refining Co. The method of preparation of high-purity copper and its alloys in either the oxygen-free or oxygen-bearing form has been described previously.1 The purity of this material, and the methods developed to produce it, provide the means for direct investigation of the very low concentration range in which the various impurities generally exist in commercial coppers. The usual necessity for extrapolation to this range using the results obtained from higher concentrations, and the interfering effects of extraneous impurities, are thus simultaneously circumvented. Since previously published data have adequately presented the effects of higher concentrations of iron, cobalt and nickel, the present investigation has been confined to the composition range 0 to 0.05 per cent. All alloys were initially prepared in the form of oxygen-free continuous cast rod, the weighed alloying additions in suitable form being charged with the pure copper to the continuous casting crucible. The best of the available high-purity alloying materials were used, and spectrographic analyses confirmed the absence of interfering elements from the alloys formed. Each series was compounded in the direction of increasing concentration, starting with pure copper in a new crucible and finishing with the 0.05 per cent alloy. Composition was closely controlled by adding the alloying element in the form of a carefully compounded and analyzed master alloy rendered uniform by continuous casting. The accuracy of this method of synthesis was proved by chemical analysis of the more concentrated alloys, and, accordingly, there is every reason to credit the stated composition of the very dilute alloys in the range where chemical analysis becomes highly uncertain. Oxygen-free samples for measurements of conductivity and softening temperature were obtained by drawing the continuous cast rod to wire of 0.081-in. diameter, employing a number of intermediate anneals to refine the grain structure. The

Jan 1, 1942

By B. Hines

Grinding efficiency in a vertical stirred mill is affected by a wide range of process and mill configuration variables. Of these, the media fill, size, and intrinsic density have a significant effect on power draw and grinding performance. Media-related factors that influence grinding performance include, e.g.,a higher media filling providing additional particle breakage sites, or a lower bead density decreasing the running torque at a given media filling. It has been estimated that the grinding media can cause up to a 30% change in the specific energy required to grind. FLSmidth has generally recommended that the intrinsic density (specific gravity) of the grinding media be more than triple the slurry density. This density difference helps to ensure that sufficient stress intensity is generated in the mill to provide particle breakage. It also reduces the chance of media ?float? if there is a spike in either slurry density or slurry flow rate. The VXPmills have historically operated at slurry density values between 1.2 and 1.5 kg/L, which translates to nominal bead intrinsic density range between 3.6 and 4.5 kg/L. The current trend towards regrinding bulk flotation concentrates to even finer sizes, to improve recoveries of fine grained minerals, has provided motivation to consider closed-circuit operation of stirred media mills. The slurry density in this application is typically higher than in open-circuit operation due to the higher percent solids in cyclone underflows. An additional effect is that closed-circuit operation increases the potential for media float due to higher flow rates as slurry is recycled to the mill. The normal progression in extending the operating range of existing equipment is to carry out laboratory testing before pilot-scale and plant-scale trials. The results presented in this paper examine the media density to slurry density ratio and its effect on grinding performance.

Feb 23, 2014

By E. R. Bobicki

"Low-grade ultramafic nickel ores, while representing a large potential nickel resource, are difficult to process due to their serpentine content. Microwave treatment is proposed as a technique to improve the beneficiation of ultramafic nickel ores by converting the constituent serpentine to olivine. The present paper reviews the microwave heating response of ultramafic nickel ores and resultant changes in mineralogy, as well as effects on grinding and slurry rheology. Beyond nickel extraction, microwave treatment improves the mineral carbon storage capacity of ultramafic ore tailings, providing a potential source of additional revenue via the sale of carbon credits. The combined positive effects, considered in the context of the whole operation, suggest an economically viable process is possible.INTRODUCTIONAs high-grade deposits become depleted, the processing of low-grade ores has become increasingly important. One such resource is low-grade ultramafic nickel ores. While representing a large source of nickel, these ores are difficult to process due to their serpentine content. Serpentine is a phyllosilicate mineral consisting of 1:1 stacked sheets of silica tetrahedra and magnesium hydroxide octahedra. There are three primary polymorphs: lizardite (platy), antigorite (corrugated) and chrysotile (coiled, fibrous). The anisotropic nature and non-spherical morphology of serpentine particles leads to complex rheology. Suspensions of serpentine minerals, especially those of chrysotile, exhibit high viscosity and yield stress, which can have a negative effect on comminution, flotation and dewatering operations. In flotation, serpentine is known to slime-coat pentlandite, a valuable nickel mineral, and form bubble-fibre aggregates that report to the froth, reducing nickel concentrate grade and recovery. Methods used to counteract the effects of serpentine in processing include desliming, the addition of chemical dispersants, salts or acid, and dilution (Bobicki et al., 2014a). Microwave pre-treatment has been proposed as an alternative way to eliminate the deleterious effects of serpentine in ultramafic nickel ore processing by converting the serpentine to olivine via dehydroxylation, which occurs at 600-700oC (Reaction 1). Olivine is isotropic, consisting of isolated silica tetrahedra linked by octahedrally coordinated magnesium ions, and has the same surface potential as pentlandite at the pH of flotation (~pH 9). Furthermore, since olivine is more reactive to CO2 than serpentine, microwave pre-treatment creates an opportunity to store more CO2 in tailings, an attractive option for mining operations looking to increase their bottom line where carbon pricing exists."

Jan 1, 2018

By R. Larry Grayson

In the October 1998 issue of the Holmes Safety Association Bulletin, NIOSH authors Mark Stephenson and Carol Merry wrote the article Hearing loss among miners and measures to protect hearing, which focused on the extensiveness of hearing loss among miners and the use of hearing protection to prevent hearing loss. While the primary importance of engineering controls in preventing hearing loss was discussed, since miners do not generally have control over their work en­vironment or assignments, the article focused on the importance of consis­tent use of hearing protection. In this article, all aspects of a compre­hensive approach to the prevention of hearing loss in miners will be covered. The discussions will do the following: ? describe application of the hierarchy of controls in preventing hear­ing loss in miners, ? give an example for each type of control measure and its impact, ? explain the major provisions, be­yond the hierarchy of controls, of the recent NIOSH document en-titled Criteria for a Recommended Standard: Occupa­tional Noise Exposure, Revised Criteria 1998 relative to a hearing loss prevention program, and ? summarize important points on control of noise exposure for every miner to remember, equipment in most facets of operations. Miners are well aware of noisy areas in or around equipment, icluding extraction machinery such as draglines, power shovels, longwall shearers, and continuous mining machines; powered haulage equipment such as load-haul-dumps, shuttle cars, large trucks, and continuous haulage units; roof bolting machines; jackleg drills and stopers; auxiliary equipment such as compressors, fans, and pumps; size reduction equipment, etc. They are not well aware of the insidious nature of pro­gressive hearing loss, which is per­manent, but they are generally aware of what levels of noise are hazardous and what measures can be taken to reduce their personal noise exposure. Behaviorally, however, there are many reasons why miners choose not to use hearing protection faithfully.

Jan 1, 1998

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989

By O. Bazhko, F. D. L. Uahengo, Y. R. S. Hara

Although the conventional acid-reductive leaching method effectively extracts copper (Cu) and cobalt (Co) from Cu–Co oxide ores, efforts to enhance hydrometallurgical performance are ongoing. This study evaluates the influence of sulphuric acid (H2SO4) and sodium metabisulphite (Na2S2O5) on metal extraction from Zebesha Cu–Co oxide ore using ferrous sulphate heptahydrate (FeSO4·7H2O) and ferric sulphate (Fe2(SO4)3) as lixiviants. Ore samples (<150 μm) were leached at ambient temperature for two hours, and metal concentrations were determined via X-ray fluorescence analysis. In the FeSO4·7H2O system, Co, Mn, and Ni recoveries increased w=ith Na2S2O5 concentration, reaching a maximum of approximately 80% Co at 150 kg/t, while Cu recovery remained below 5%. Conversely, with Fe2(SO4)3, Cu recovery peaked at 88% at 50 kg/t Na2S2O5, then declined to 79% at 150 kg/t. The addition of H2SO4 improved metal recoveries in both systems. Notably, 60 kg/t H2SO4 yielded 92% Cu extraction in Fe2(SO4)3, while Co, Ni, and Mn remained below 40%. However, in FeSO4·7H2O, Co recovery improved from 40% to 84%. These findings suggest Na2S2O5 is more effective for cobalt extraction with FeSO4·7H2O, whereas H2SO4 enhances copper extraction in Fe2(SO4)3.

Oct 24, 2025

By A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia?s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By David D. Spencer

As in many other areas of the Mexican economy, the legal rules applicable to mining in Mexico have been changing fast. Mexico&apos;s mining sector is opening up to levels of international participation that were unforeseeable just a few years ago. Over the last several years, Mexico has made dramatic changes in its trade and investment policies. Many of these changes have their roots in the administrations of Miguel de la Madrid and perhaps even Jose Lopez Portillo. However, the current administration of President Carlos Salinas must be given credit for articulating, advancing, promulgating and implementing these changes. Just a few short years ago, few people believed Mexico would repeal so many of its restrictions on foreign investment and lower its average tariff level from something around 100% to less than 10%, where it is today. NAFTA and mining The North American Free Trade Agreement (NAFTA) is the most comprehensive international expression of Mexico&apos;s new policies. Except perhaps for the agreements establishing the European Union, NAFTA is the most detailed trade agreement ever written, consisting of about 2000 pages. The provisions of NAFTA with the greatest relevance to the mining industry include the chapters on investment and government procurement. Many mining companies may also find the temporary work provisions relevant. Finally, no discussion of NAFTA and the mining industry would be complete without some mention of the North American Agreement on Environmental Cooperation, the so-called Environmental Side Agreement.

Jan 1, 1994

By Robin Schott

The blast furnace process is the most important process to produce pig iron. The necessary process energy is mainly covered by coke. But the production of coke is connected with CO2-emissions and high costs. A significant measure to reduce the coke rate and with it the CO2-emissions plus costs is pulverized coal injection (PCI) through the tuyeres into the blast furnace. A further increase to substitute coke by coal can be achieved by using the Oxycoal+ technology. This article compares and shows the cost effectiveness and the decrease of CO2-emissions with the help of simplified energy balances for the only coke operation of the blast furnace, the operation using pulverized coal injection and the operation using the Oxycoal+ technology.

Aug 17, 2017

By Robert Warner

The growing importance of screening makes an accurate measure of the quality of a sizing operation desirable. Screen efficiency is considered equal to the percentage of true undersize in the feed obtained as undersize from the screen. This method is unreliable, as it gives the same credit for removing minus 200-mesh material as for removing material just able to pass the aperature of the screen. A more accurate measure of screen efficiency is to consider only the work done on the "difficult" grains, that is, those grains of which the intermediate diameters closely approach the screen aperture.. The application of this method is given, together with the derivation of formulas and an example of their use. Is AN accurate measurement of the efficiency of a screen under a given set of operating conditions valuable? If so, what is the efficiency; of, a screen and how can it be measured? Sizing, especially of the finer sizes of material, has increased in importance in the development of flow sheets as a result of the perfecting of the rapid vibrating screens. More consideration should be given screens in the preparation of ball-mill feed, where they permit the admission of a dryer feed than, the classifier. Where possible, the introduction of a screen ahead of the primary ball-mill, and the diverting of ore below, say, 4 mm. to a secondary mill, might result in a greater overall economy because of the thicker feed and the better, adjustment of crushing media and mill operation to the reduction demanded. With the present trend back toward a combination of gravity methods and flotation, rather than flotation alone, the accurate, economical sizing possible with the new screens makes fine jigging a method to be considered. W. 0. Borcherdt1 and John Bland2 discuss the screening problem and also the value of close sizing in the concentration of some of the rare-metal ores. If a screen is to be used, it should be selected in competition with others; other things being equal, that screen which makes the cleanest oversize should be preferred. The quality of the screening and the tons

Jan 1, 1924