Search Documents

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Brooke County and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 191 million short tons as of January 1, 1954. Of this total, 190 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By A. M. Hefny, F. P. Siew, P. G. Ranjith

Fracture initiation and propagation, being one of the most intensive subjects in rock mechanics; contribute significantly to the deformation of jointed rock masses. An experimental study on fractured granitic rock was carried out to determine the peak strength of specimen under triaxial loading conditions. The commonly observed failure mode for rock specimens in this study was found to be the shearing of the plane of weakness. The minimum peak strength of fractured rock is observed when the joint orientation is approximately 70° to the horizontal axis. Based on experimental test data, an empirical expression was developed to accommodate the effect of joint orientation and joint trace length in estimating the peak strength of fractured rocks. The predicted values of peak strength using the proposed equation well agree with the experimental results carried out on singly fractured specimens under triaxial loading conditions. The threshold stress values of crack initiation and propagation depend on joint geometrical parameters, their degree of interconnectivity, as well as surrounding stresses on the fracture plane.

Jan 1, 2003

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By R. Lombard

"Water is a very important component in the production process at underground coal mines. Current unfavourable economic conditions have forced the coal mining industry to identify and address every possible bottleneck preventing optimal production. An increase in water-related downtime was identified as one of the bottlenecks at Goedehoop Colliery’s Vlaklaagte Shaft. The purpose of this project was to identify the various causes that contributed to the high downtime (501 hours in 2013, which led to a potential profit loss of R12.9 million) and to suggest possible solutions.After a thorough investigation the main causes of water-related downtime were identified as low water pressure and low water flow caused by pipe leakages and bursts. The main root cause for the low water flow and pressure was identified as being the low pressure resistance (1600kPa) of the thin-walled galvanized steel pipes used in the underground inbye water reticulation system. The pipes were selected according to the previous 1000 kPa pressure requirement for the continuous miner. However, the pressure requirement changed to 1500 kPa, which resulted in the pipes being exposed to much higher pressures than designed for.The water reticulation system was reviewed and current and future underground pipe layout and water requirements were determined for the shaft. The time frame in which the water consumption would be the highest was determined to be between 1 January 2014 and 7 September2014. Machine and sprayer specifications were used to determine theater consumption at the shaft. Three different solutions were considered to solve the water-related downtime problem and to ensure the efficient supply of water to the newly open sections. Permanent underground concrete dams, semi-mobile dams, or new pipe columns with a higher pressure resistance of 3200 kPa were considered. A trade-off study (taking into consideration cost, time to completion and ease of implementation, maintenance requirements, safety, and flexibility) was completed to determine which of these solutions would be most viable.Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Engineering)"

Jan 1, 2015

By Júlia Guimarães Sanches

O curso de Engenharia de Minas sofreu uma expansão, juntamente com todo o ensino superior no país, por volta de 2005. O objetivo do presente estudo é avaliar as características dos cursos do país e realizar uma comparação com cursos de outros países com grande produção mineral. Foi feito um levantamento inicial a partir de informações disponíveis nos sites do MEC, INEP e das universidades. Como complemento, realizou-se um questionário com os coordenadores dos cursos de Engenharia de Minas do Brasil. Foram compilados ainda dados relativos à estrutura curricular e carga horária dos cursos de Engenharia de Minas dos EUA, Canadá, Austrália, Chile e África do Sul. Em relação à comparação das grades curriculares com os cursos de outros países, observou-se que no Brasil o curso possui uma maior cara horária de Tratamento de Minérios em detrimento da lavra. Nos demais países estudados, o foco das disciplinas é a lavra, já que nestes países a área de Tratamento de Minérios é assunto de outras Engenharias.

Oct 30, 2017

By L. Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pinpoint the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable temperature readings and gas analyses could have verified satisfactory activity. Hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: good record keeping is a necessity for collection of representative catalyst samples; reliable operating data is an inevitable starting point for all analysis; and trending of operating data is a must for plant optimization and troubleshooting. In addition, these catalyst management tools will give continuous updated knowledge of the catalyst status in each bed, providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking operating data, temperature optimization and good record keeping.

Jan 1, 2009

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982

By R. Grandori, L. Pellegrini

The construction of the La Joya hydropower plant (Costa Rica) was awarded by the Spanish power company, Union Fenosa, to the Italian Joint Venture formed by the companies SELI SpA and Ghella SpA. The project, located in a mountainous region of central Costa Rica, includes a 7.9-km-long head race tunnel having an excavation diameter of 6.18 m. A double-shielded TBM was selected to perform the tunnel excavation, which involved mainly volcanic rocks in variable but generally very weak conditions. The tunnel crossed long and continuous sections in completely weathered rock masses with no residual cohesion and with high water inflows. The paper describes and analyzes: The special methods adopted to overcome these sections with the TBM includ-ing face stabilization by chemical grout and foams as well small by-pass tunnels in the crown combined with TBM advance/support The grouting design and the grouting method that was implemented to meet the waterproof design specifications and restore the original groundwater level in the mountain The additional geological investigations performed to improve the knowledge of the rock mass in front of the TBM and the outcomes of these investigations The performance of the TBM in different ground conditions and on average along the entire tunnel Finally, the author’s comment about the possibility of implementing and improving the technologies experimented with in this project in future similar applications.

Jan 1, 2007

By K. J. Griffin, G. W. Rosval

"In our increasingly competitive market, attempts to improve productivity by increasing axle loads have placed more severe demands on rails. CP Rail thus requires stronger, tougher, and more wear-resistant rails from steel manufacturers. The choice of any rail steel is always a compromise between technical and economic factors. The technical assessment of a candidate rail consists of laboratory and field testing. Laboratory evaluation of rail steels cannot adequately model many service conditions and must, therefore, be supplemented by long-term field testing. The field testing conducted on CP Rail is the subject of this paper.Long-term, in-track, assessment of candidate rail steels begins with the selection and re-laying of a test curve representative of the intended service with both the candidate rail and a control rail steel (i.e. the present intermediate or premium rail standard). The wear performance of the candidate rail is evaluated, in relation to that of the control rail, using data obtained with a rail profilometer developed by the Research and Development Department of CP Rail. Qualitative observations are also periodically made to evaluate the relative susceptibilities of the two rail types to surface defect formation. Testing continues until stable metal loss patterns are achieved. Relative life predictions are then made and detailed monitoring of the test site is discontinued.CP Rail's in-track assessment program for premium rails has resulted in the establishment of a new CP Rail premium rail standard - low-alloy, head-hardened, rails have replaced high alloy rails. The wear/fatigue lives of these new premium rails exceed those of our previous standard by more than 50%, and they also exhibit excellent weldability. CP Rail will continue to evaluate new premium and intermediate strength rail products."

Jan 1, 1988

Validation and Simulation of Optimised Compressive Crushing Ores and aggregates are used in countless applications all around in the society. The frequent and escalating usage of these natural resources requires efforts aimed at not only making do with what is available, but also undertaking actions to improve the production yield and the processes involved. This strive to improve the performance and efficiency of existing crushers and crushing processes has brought about research concerning optimisation of crushing plants as well as theoretical optimisation of crushing. Previous work shows that different applications and different materials require different compressive crushing in order to accomplish a theoretically optimal size distribution. These optimisation results, obtained by genetic evolutionary algorithms and evaluated with so called fitness functions, convey the theoretically optimal number of compressions and their corresponding compression ratios. Presented in this paper are thus some laboratory crushing tests, which are conducted in order to validate a set of previously optimised crushing sequences. More specifically, interparticle crushing sequences are carried out in a Piston-die testing equipment, where samples are sieved between each compression. The subsequent analysis of these results shows good correlation with model predictions, which combined with a comparative study between presented optimisation results and measured data from a real crusher indicate a significant potential for improvement. However, before redesigning crushers according to what is theoretically optimal, the resulting impact as well as the effects on the outcome of a crushing plant must be examined. Crushing plant simulations using the software PlantDesigner« are consequently performed. Models of existing crushers are altered, resulting in changed particle size distributions from some of the crushers in a crushing plant. Thence, it is concluded that significant gains can be made in terms of capacity, process yield and energy consumption.

Sep 13, 2010

By J. B. Boisvert, P. Oshust

A significant source of uncertainty in the diamond resource contained in kimberlite pipes is the volume of the pipes. Often the material within a pipe will be mined as ore, leaving the actual geometry of the pipe as a significant source of uncertainty. It is desirable to use stochastic techniques, rather than deterministic methods, to model pipe geometry because stochastic techniques generate multiple realizations that are reproducible and can be used to assess uncertainty in pipe geometry. The proposed methodology uses sequential Gaussian simulation of pierce point locations interpreted from drillholes through a kimberlite pipe. Kimberlite pipes are approximately cylindrical in shape; therefore, the data are transformed to cylindrical coordinates to facilitate the simulation of pipe geometry. Rather than using xyz coordinates to define the pierce points, z, ??and pipe radius are used. The radius variable can be simulated in z-??space to generate multiple realizations of pipe volume. Uncertainty in the volume of the pipe can then be evaluated. This methodology is demonstrated with a kimberlite pipe at BHP Billiton’s Ekati diamond mine.

Jan 1, 2008

By Ned Baker

Details are given of a fuel-induction system for a hydrogen, fueled engine. The induction system was designed to preclude backfire otherwise common in hydrogen fueled engines. System features and test data are presented and discussed in the context of the requirements peculiar to use in an underground mine environment. The fuel induction-system when tested in conjunction with a modified Caterpillar 3304 engine provided backfire free engine operation and satisfactory engine performance.

Jan 1, 1982

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By J. B. Clark

In multiphase ternary diffusion studies, plots of the variation bf the composition on the isotherm constitutes one of the most effective methods of presenting experimental results, especially if such plots are made in a manner which relates the composition path on the isotherm with the diffusion layer structure in the couple. Unfortunately, if different conventions for plotting are used serious misinterpretations occur readily, causing apparent disagreement between investigators who actually share the same viewpoint. A common convention for mapping these diffusion paths is needed at this time because with the increasing use of the electron-probe X-ray microanalyzer, a much greater number of ternary diffusion studies can be expected in the near future. In an effort to prevent unnecessary confusion in the future litera- ture, a convention for these plots is proposed, as outlined below. A hypothetical example of the use of these conventions is given in Fig. 1 where the path of composition through the diffusion structure of the 100 pct A/50 pct B, 50 pct C couple is plotted on the appropriate isotherm of the ABC system. The lower case letters relate the region in the diffusion layer structure to the appropriate composition on the ternary isotherm. 1) The diffusion path is plotted on the isothermal section corresponding to the diffusion temperature of the couple. 2) The terminal compositions of the plotted diffusion path are the initial compositions of the couple halves—provided infinite boundary conditions are maintained. If, in either couple half, infinite conditions are not maintained, then the path terminates at the composition of the exterior surface of the couple. If, at this surface, the composition varies with time or if the plotted path is time dependent, then the diffusion time should be noted beside the plotted path. 3) A solid line crossing a single phase field (e.g., line a-b in Fig. 1) denotes an existing layer of that phase in the diffused couple. 4) A dashed line crossing a two-phase field parallel to the tie lines (e.g., line g-h) represents an interface between the two phases with interfacial compositions designated by the ends of the tie-line. The line represents no spatial extent. 5) A solid line crossing a two-phase field so as to cut tie lines (e.g., line b-c or line j-k) represents a locally equilibrated columnar two-phase layer. The solid line should cut those tie lines which correspond to the lateral interfacial equilibria along the columnar

Jan 1, 1963

By Lowell Stroud

This report is the third in a series presenting equilibrium vapor-liquid data for helium-bearing natural gases. The first two reports contained phase data for the gases processed for helium at the Bureau of Mines Amarillo and Exell, Tex., helium plants. The present report offers similar information for a lower-helium-content (0.75 mole-percent) natural gas to be processed in the Department of the Interior's long-range helium-conservation program. A windowed-cell apparatus was used to obtain 218 samples of equilibrium vapor and liquid phases at 73 experimental conditions ranging in temperature from -100° F to -275° F and in pressure from 100 to 500 psi. From the phase data, the condensation characteristics, helium solubility, and equilibrium-vaporization-coefficient data for helium, nitrogen, and methane were evaluated. The effect of using a. preliminary hydrocarbon trap upon the subsequent vapor-liquid compositions is reported. A brief comment regarding the composition effect of passing the gas through a gasoline-removal unit is also included.

Jan 1, 1963

By Alain Bouchard, Germain Labonté, Jim Barrett

"Mill feed materials that are not run-of-mine ore are often a challenge for mineral processors and tend to accumulate in stockpiles, where they remain unprocessed for many years and become “slow moving inventories”. During a complete re-evaluation of the Clarabelle Mill operation (38,000 ton/day capacity) in 2000, it was concluded that there was an opportunity to assemble a 5,000 ton/day custom circuit to treat such stockpiles in the equipment that remained available during regularly scheduled maintenance shut-downs.This project was part of the larger Mill Redesign Project and involved testing the intended flowsheet under a number of operating scenarios for the first material to be treated: spent refractory bricks. The laboratory focus was on how to maximize returns using the available equipment and reagents.The circuit was successfully commissioned in the fall of 2000. As the brick stockpile was depleted, other potential feeds were evaluated at the laboratory, as well as in the new custom circuit itself. Processing of the spent refractory brick has yielded a significant contribution to the profitability of INCO. Significant opportunities lie ahead for generating more value from other slow moving inventories.INTRODUCTIONIntegrated mining operations tend to have slow moving inventories along the path from the mines to the finished products. Spent refractory bricks from furnaces and converters and furnace bottoms are materials that often end up in long-tern stockpiles. Such stockpiles are a challenge, although they represent small tonnages on an annual basis, because they are unique materials, which cannot be readily brought into the process at a rate anywhere near that at which they are produced, due to the high contents of deleterious components such as chromite or magnesia. Accumulation over years will eventually yield a metal inventory worthy of consideration given the right opportunity, such as availability of spare equipment or peak metal prices."

Jan 1, 2002

By D J. Robinson, L L. Kuhar

"Regardless of orebody value, at some stage, the pit will reach a depth where the reward for mining wider and/or deeper is not justified by the anticipated returns. ‘Last-blast’ strategies may help to some degree in recovering additional quantities of the resource but when a pit remains, there is often significant value left in the ground. In addition, in many cases, one or many good reasons may dictate why going underground and pursuing the orebody below the pit is also not justifiable. Whereas the company can hopefully move on to other more prospective parts of the orebody, the remaining options for the pit are usually very limited. Typically the pit is either held for potentially more favourable future pit expansion opportunities or it could be used for an alternative purpose, such as tailings or waste storage. This paper will present an alternative option that involves the direct extraction of values using in situ recovery (ISR) methods to recover additional value metals from the walls and/or floor of the pit. ISR involves circulating a fluid through the remaining orebody, solubilising the target metal and subsequently returning the solution to the surface for metal recovery. ISR is not the panacea to all but it has been employed selectively in the minerals industry for some time and the production of metals, such as uranium, rely heavily on this approach. ISR is not yet considered by many operators as an approach to compete with open pit or underground mining, largely because of the perceived limitations of this approach and the perceptions of risk. Rapid recent development of tools and enabling technologies relevant to ISR have made us reconsider the most economic approach to extracting many other metals from known mineral systems, even those currently listed as subeconomic. We suggest that ISR has the potential to make mine operators rethink the end of the pit life and adopt an innovative ISR approach to work toward a more complete recovery of value metals from existing pits.Citation:Kuhar, L L and Robinson, D J, 2016. In-pit In Situ Recovery - a New Approach That May Allow for Increased Value Extraction before Pit Closure, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 275–283 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Holla L, Tyminski A

Stowing has been successfully used in many countries as a means of controlling surface subsidence, minimi ing incidences of spontaneous combustion, maintaining gate road stability and maximising coal recovery.Australian experience in stowing is limited but in the future increased extraction of thicker and/or multiple seams by longwall operations and resolution of conflict of alternative land u'ses may necessitate the use of stowing in coal mining. At present there is little incentive for mining companies to introduce and operate a stowing system because costs have to be borne by the individual companies and benefits spill over to society and the State. Cost sharing by the industry and State incentives may overcome the problem of cost disincentive.

Jan 1, 1987

By O. J. C. Runnalls

"Canada became the world's largest uranium producer in 1984. That leadership position is likely to be maintained for many years into the future because of a firm production base, many undeveloped known deposits with commercial promise, and a large geologicalpotential for new discoveries.There are some uncertainties on the horizon, principally because of restrictive actions in process within the U.S.A., which are aimed at preserving a deteriorating domestic uranium industry. Should such actions result in import restrictions, for example, there would be a negative effect on foreign producers at least in the short term. Canada may avoid such difficulties under a tentative U.S.-Canada free-trade agreement where restrictions on the import of Canadian uranium into the United States would be eliminated. Over the longer term, demand for Canada's uranium resources will grow because of the foreseen growth in the world's installed nuclear power capacity. IntroductionSince the phenomenon of nuclear fission was discovered in 1938, the utilization of uranium has grown substantially. Initially, the principal use for uranium was in the production of nuclear weapons. However, once civilian nuclear power reactors began to be built in the 1950s, an increasing fraction of uranium output was directed to the production of fuel elements for use in electricity generating stations.The cumulative uranium production by those countries in the World Outside Centrally-Planned-Economies Areas, WOCA, during the period 1938 to 1985 exceeded 800 000 tonnes of uranium. Some 60% of that was mined in the United States and Canada, as indicated in Figure 1. In 1986, nearly 80% of WOCA output came from five countries, Canada, United States, South Africa, Australia, and Namibia, as indicated in Table 1 and illustrated in Figure 2.During the past decade the world annual consumption of nuclear energy has more than tripled (Fig. 3). As of December 31, 1986, the world total of nuclear power reactors had reached 394 with a total net capacity of 270 GWe. The thermal output from nuclear power plants in 1985 exceeded 60% of the energy contained in all of the oil produced that year in the Middle East. Thus, nuclear power has already become an important component in the world energy supply picture."

Jan 1, 1988