Search Documents

By Clyde Baker

Drilled shafts for many situations offer an economical alternative to driven piles. The Federal Highway Administration (FHWA) has spent considerable time and money in research and developing design and construction guidelines for drilled shafts. However, the full potential of the technology may not be realized because of the uncertainty of the effects of construction on the actual service behavior and the lack of either reliable quality control tests to check for or evaluate defects, or inexpensive load test procedures. Static load testing is very expensive and it is not feasible to load test each shaft on a project. Therefore, other means are necessary to confirm or evaluate the integrity of the completed drilled shaft or to determine the capacity of the completed shaft.

Jan 1, 1989

By Tom Gonzales

At San Manuel, AZ, Magma Metals Co. operates an Outokumpu flash furnace, four Peirce-Smith converters and two anode casting wheels that are supported by six anode vessels. Process gasses from the flash furnace and converters are treated in a two-train/ double-contact sulfuric acid plant. The plant captures 98% of the sulfur. A new flash furnace was commissioned in July 1988. It has since processed more than 2.7 Mt (3 million st) of sulfide concentrate without a major rebuild. The company has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. Process flow description At Magma's San Manuel plant, concentrates and other copper-bearing material are blended and conveyed from two separate areas of the plant to three 420 t (465 st) capacity wet charge bins located above the rotary dryer. Flash furnace silica flux is conveyed to a 227-t (250-st) capacity fine flux bin located adjacent to the wet charge bins. The concentrate and flux are blended in controlled amounts and fed into a 168-t/ h (185-stph) gas-fired rotary dryer. The wet charge enters the dryer at 8% moisture and is dried to 0.2% moisture. The dried charge is pneumatically conveyed to a 580-t/h (640-stph) dry charge bin located above the flash furnace. Flash furnace charge is drawn from the bin by two drag conveyors at a concentrate feed rate of 145 t/h (160 stph). The charge is mixed with enriched combustion air and injected into the furnace reaction shaft. In the reaction shaft, the charge is oxidized to form matte, slag and a rich SO, off-gas.

Jan 1, 1992

By A. Paviani

The subject of this session is "Equipment Installa­tion, Recent Developments". This is a subject which is not usually addressed at conferences of Foundation Engineering. It is rare to find sessions dealing with the technological side of deep foundations, a subject which only recently seems to have aroused sufficient interest at national and international conferences. It is therefore natural for the subject of "Equipment", or the tools used to implement the various "technologies", to be over­looked or mentioned only occasionally during the discussion of other issues. At conferences, most of the attention is attached to research and to the theoretical interpretation of the performance and behaviour of deep foundations, as well as to establishing the most suitable calculation algorithms and approaches for the study, design and control of foundation structures. It is almost as if the subject of equipment is felt to be less important or, perhaps, that it is considered to belong more strictly to mechanical engineering than to civil engineering.

Jan 1, 1994

By Parker A. J, Grimsey E. J

Studies have been carried out on the dead roasting of a copper-iron and a copper-nickel-iron sulfide concentrate, followed by segregation roasting with coal and leaching with either curpric sulfate in aqueous acetonitrile or cupric chloride in brine solution to preferentially solubilize copper. The effect of dead roasting and segregation roasting conditions on the overall leaching of copper and the separation of copper from iron and iron and nickel is reported. An excellent separation of copper from iron and a good separation of copper from iron and nickel can be obtained provided sulfur is removed to 0.5 per cent or less during the dead roast and provided the coal addition and temperature of the segregation roast are near the minima required for the segregation of copper.

Jan 1, 1983

By V. K. Alves, P. Lacoste-Bouchet

"In order to improve ball milling efficiency in pellet plants, Companhia Vale de Rio Doce (CVRD), experiments new technologies in Santa Luzia (M.G. – Brazil) research center facility. Pilot grinding tests have been conducted with small grinding media, size distributed from 5 to 12 mm (millpebs). Tests have been conducted on an ore from CVRD’s Usina 5 Nibrasco, in Vitória, Brazil. A sample of the regrind circuit feed was obtained and used in comparative grinding tests with two types of grinding charges: 100% balls and a blend of 70% balls and 30% millpebs by weight. According to the balls charge, the grinding media mixture has showed the following benefits: reduction of the power draw, increase of the mill capacity, reduction of the circulating load and a slight increase of the ore blaine. Following the results obtained, CVRD is going to further explore the regrinding potential of millpebs.INTRODUCTIONCompanhnia Vale de Rio Doce (CVRD) is the largest mining company in Brazil. CVRD is involved in iron, base metals, gold and bauxite industries. Moreover, CVRD operates several pelletizing plants in Brazil and in other countries.CVRD’s Center for Mineral Development (CDM) is equipped with a comminution laboratory where studies are carried out that are aimed at the optimization of existing plants at several mining sites as well as the technical and economical feasibility of new projects. The laboratory is equipped with a complete pilot plant with several mills and classifiers, enabling continuous grinding tests in grinding circuits of almost any capacity and characteristics.In January 2004, CVRD undertook to conduct pilot tests at CDM for evaluating the effect of small grinding media on ball milling efficiency. Generally speaking, it is not unusual for operators to add oversize grinding media in a conventional regrind mill. This fact originates mainly from prohibitive prices of grinding media below 25 mm due to a production capacity decrease of grinding media producers. The size of the grinding media is an important variable affecting ball milling efficiency. Use of oversize balls decreases the number of contact surface between which particles can be caught and broken."

Jan 1, 2005

By John Convey

This short paper deals with the subject of research and its relation to productivity. All who have stopped to even think about industrial re-search and its impact on the nation-al economy take for granted that research and development are pre-requisite to increased productivity. It is another matter, however, to identify and properly evaluate the many factors entering into the relationship between the two. Some studies are currently underway in the United States on the subject, but, so far, nothing much in the way of conclusive data has come to light. In Canada, we have not yet even produced any statistical figures on national productivity, although work is now being done on this subject and information will soon be available. The usefulness of being able to measure the benefits of investment in re-search and development in terms of industrial growth or productivity need not be laboured for the benefit of those interested in research management.

Jan 1, 1964

By Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hard rock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

May 1, 2007

By C. Feng, C. Elbaum

Knoop hardness measurements were carried out on large grains of iodide titanium containing different amounts of oxygen. For each oxygen content the hardness is recorded ainingas a function of the crystal orientation and of the angle 4 between the indenter diagonal and the projection of the C (hexad) axis in the surface. The results can be expressed by the following relation; hardness = n-k cos 2ø, where n and k are constants for a given oxygen content and crystal surface orientation. A NISOTROPY of hardness is a well-known phe-nomenon and has been reported for many metals.1-3 At the present time, however, such information is not available in the literature for titanium. Consequently, a systematic study of the simultaneous effects of oxygen content and crystallographic orientation on the hardness of titanium was undertaken in this laboratory. Evaluations of oxygen content in titanium are frequently carried out through hardness tests. Although such procedures may be justified in small grain specimens, the results of the present investigation indicate that the anisotropy of hardness should be taken into account in the case of coarsegrained specimens as well as in the case of pronounced preferred orientation. Materials and Experimental Procedures Iodide titanium, 99.99 pet pure and containing of the order of 0.002 wt pet O, was used throughout this investigation. The metal was arc melted in an argon atmosphere and cold rolled into strips 1/16 in. thick. These strips were subsequently recrystal-lized and strain annealed in vacuum (10" mm Hg or better) at 850°C in order to produce crystals varying in diameter from 10 to 25 mm. Oxygen was introduced into selected large crystals by heating at 700°C in an atmosphere of pure oxygen under an observed pressure of approximately 50 mm Hg. Each sample was subsequently annealed in vacuum at 850°C for 100 hr, in order to homogenize the oxygen content throughout the specimen. It was found that longer annealing was not necessary, for no change of surface hardness in a given direction was detected after prolonged annealing. The oxygen content was determined by the difference in weight of the specimens before and after the oxidation-annealing cycle. The accuracy of oxygen determination is within ±0.1 mg in samples weighing 0.5 to 1 g. A vacuum fusion analysis of oxygen was performed on several samples and gave results in good agreement with the ones obtained by the weight change. It should be emphasized that expected weight losses through evaporation of the metal in vacuum at 850°C' are many orders of magnitude lower than the precision of these measurements. Following the annealing treatment, both oxidized and unoxidized crystals were carefully polished. All detectable traces of surface cold working were removed by repeated polishing and etching. Laue back reflection X-ray patterns were taken for each crystal for the purpose of determining the orientation and ascertaining the absence of substructures detectable by this method. Hardness measurements, using a 1 kg load, were subsequently carried out on a Tukon hardness tester equipped with a Knoop indenter. The Knoop indenter was used throughout this work because indentations obtained by means of a Vickers indenter are considerably distorted due to the anisotropy of the elastic constants in titanium. Such distortions are much less pronounced in the case of Knoop indentations, although for some orientations a cer-

Jan 1, 1959

The development of information concerning mesothelioma in South Africa started with the 1959 finding of Dr. J. Christopher Wagner of cases of mesothelioma in persons living in the vicinity or working in crocidolite mines in Cape Province. After more than 40 years, the data from South Africa now provide important insights into the differences in mesothelioma risk associated with different asbestos fiber-types. Three case series reports and one analytical report were reviewed in this session. In total, information on 504 proven cases was presented. There were 28% of cases arising from occupational exposure in mining, 35% from non-mining occupations, 23% from environmental exposures; 14% where no exposure was established and 9% where the exposure was unknown. Among the 129 cases for which occupational exposure and asbestos fiber-type were established, 115 cases were associated with occupational exposure to Cape crocidolite; 1 case associated with occupational exposure to Transvaal crocidolite and 9 cases with occupational exposure to amosite (grunerite asbestos) and 4 cases with occupational exposure to mixed fiber-types. There were no cases associated with chrysotile asbestos. There were 33 cases of environmental mesothelioma linked to Cape crocidolite exposure and 2 to exposure to amosite and crocidolite but none to Transvaal amosite alone or to chrysotile. The evidence shows that amosite is capable of causing mesothelioma but that the major risk in South Africa is associated with Cape crocidolite.

Jan 1, 2008

By Claude Bazin

"The On-Stream Analyzer has proven and is still proving to be an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the provided assays using a real-time material balance program to calculate the distribution of solids within the streams of a circuit. Mass balance results can be used for process control, process analysis and detection of sensors malfunction. Examples from 3 Canadian and one American concentrators are presented to illustrate the potential of the method.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants is increasing. On-Stream Analyzers provide X-rays pulse counts that are converted into assays using multilinear regression programs. The estimated assays are passed to the flotation operators, via an operator console, or to control loops of various degrees of complexity (McKee, 1991) implemented in a Distributed Control System (DCS). Operators and/or controllers take control actions based on these assays to ensure an adequate operation of the plant. Although this application pays off very rapidly for the purchase of the OSA, one should ask: Could we get more from the OSA?Some plants reported the use of OSA measurements to process optimization (McKee, 1991). The optimization strategy is based upon economic indices calculated from metal recovery using the 2 product formulae (Wills, 1992, page 124). The 2 product formulae is however sensitive to measurement errors in the assays and can lead to considerable scatter in the calculated indices (Hodouin et al., 1993). Least squares algorithms provide an interesting alternative to filter out measurement errors (Spring, 1992). This paper presents a recursive least squares algorithm that estimates in a real time fashion the mass flow rates in a flotation plant using OSA and mass flow measurements. The algorithm is robust and its recursive structure is not demanding in terms of computation time and memory. The method was tested with data from four concentrators. Results of the material balance algorithm prove to be useful to detect sensors malfunction and may potentially be used for the control and optimization of flotation plants.The paper is divided into two sections. The first section gives a description of the proposed method. The mathematics of the method are kept to a minimum, since the detail is presented elsewhere (Bazin and Franklin, 1994). The second section shows the application of the method to different flotation plants."

Jan 1, 1995

By F. R. Camisani-Calzolari

Surface defects on continuously cast slabs require treatment by grinding. This extra phase in the process causes lower throughput of final product and extra energy costs. The elimination of slab treatment after casting implies that slabs can be direct rolled or hot charged, resulting in higher throughput and lower energy costs. To increase the number of slabs that can be direct rolled or hot charged, defects have to be predicted before a slab has completed the casting process. Transversal and longitudinal cracking, casting powder entrapment and other inclusions, bleeders, deep and uneven oscillation marks, stop marks and depressions are the defects thatare considered for prediction. A structure with two models is proposed. The first model describes the effect of mould level, water inlet temperature and casting speed (MV?manipulated variables) on 38 thermocouple temperatures (IV?intermediate variable). Casting speed is a manipulated variable while mould level and water inlet temperature are treated as measured disturbances. This model is known as the MV to IV model, and is used to control the occurrence of defects. The second model describes the effect of the thermocouple temperatures on the defects at different positions and locations on the slabs (OV?output variables). This model is known as the IV to OV model and is the predictor of defects. The models are determined using time-series methods in the form of auto regression with exogenous input using data of approximately 500 slabs cast over a period of 6 months. The models are validated using plant data from 44 slabs gathered three years later, with good results. As an example, published results give a sensitivity and specificity of 61.5 per cent and 75 per cent respectively for longitudinal cracks on validation data, while the presented method gives 63.6 per cent and 93.5 percent, respectively. The IV to OV model is used in an inversion to determine the optimal thermocouple temperatures for each slab width. Keywords: Continuous casting, model, defect, prediction, direct rolling, hot charging, goodness-of-fit, correlation, time-series, soft sensor, ARX.

Jan 1, 2003

By D N. B Skinner

Changes in the configuration of late Cenozoic volcanic arcs related to Pacific-Australian plate convergence in northern New Zealand may have localised large-scale epithermal gold-silver mineralisation to a particular part of the volcanic arc system, the Coromandel Volcanic Zone (CVZ). The history of arc-type volcanism in northern New Zealand began with the development of the continental margin Northland Volcanic Arc from early-mid Miocene (26-15 Ma). From 18-15 Ma the Northland Volcanic Arc extended south into the northern and western part of the CVZ where it is dominantly composed of andesite with lesser dacite and very minor rhyodacite. In the south, centre and east of the CVZ, younger andesite-dacite volcanism overlapped in space and time (14-5 Ma) with voluminous rhyolitic volcanism associated with rift-hosted calderas and minor basaltic eruptions. This change to bimodal rhyolitic-basaltic volcanism and extensional tectonics was a result of southwest (SW)-directed propagation of the Colville-Lau oceanic island+ arc into the north-northwest (NNW) trending Northland Volcanic Arc and its underlying continental crust. The extensional tectonic regime created in the collision zone between the two arcs is also the site of the 14-6 Ma Coromandel epithermal gold-silver province, which contains some 50 separate deposits and has a production (1862-1996) of about 300 t Au and 1150 t Ag. Extensional tectonics facilitated the emplacement of silicic magma at shallow crustal level and led to reactivation of deep basement faults. The resulting enhanced heat flow and fault-focused fluid flow localised large hydrothermal systems and associated extensive low-sulphidation epithermal gold-silver deposits in the southern part of the province, as at Waihi, Golden Cross and Karangahake.

Jan 1, 1997

By Neil T. Russo, Peter M. Kandaris, Jogi S. Gadok

"Assessment of subsurface data for foundation design in support of long high voltage electric transmission lines is best accomplished using a probabilistic strategy since only a small portion of structure locations are typically sampled. Probabilistic approaches provide a tool to evaluate site uncertainty in a systematic and rational manner. This paper provides a case history of a risk-based design approach for a recently completed 191-mile long 69/161/345kV steel monopole transmission line traversing Central Iowa. The project owner made available limited subsurface information at project initiation, requiring the design team to obtain additional data within a constrained budget for 1067 large diameter, laterally-loaded deep drilled shaft reinforced concrete piers. The team commissioned a geologic desktop study to reduce uncertainty in subsurface evaluations and aid in selecting additional sample sites. In total, investigation programs tested approximately 15 percent of structure sites. The paper details the probabilistic approach used to estimate foundation geotechnical design parameters, with information from the various studies categorizing strata both laterally and with depth. Low-bound parameters were estimated via a statistical approach at a predetermined reliability level. Significant savings resulted from this approach when compared to conservative deterministic processes. Project QA/QC logged subsurface soil conditions during foundation excavation, then compared as-found conditions to the conditions assumed for design. The team redesigned foundations if either a non-conservative variance in soil conditions was observed or if bedrock elevation differed significantly from design assumptions. As a result, only 22 out of 1067 foundations required modification during construction (2% variance from initial design) with negligible impact on the construction budget and schedule.INTRODUCTIONFoundation design for long high voltage transmission lines presents a unique challenge in that the assessment of subsurface conditions typically requires substantial data that may or may not be obtainable. Investigations are usually performed well in advance of construction, often with limited access to structure sites and typically in remote areas. Probability and risk-based investigation and design strategies offer an opportunity to systematically estimate subsurface profiles and geotechnical design properties with limited data. Risk can be further reduced with dedicated field inspection of foundation construction along with good field and design team communication during construction. This paper presents a case history of probabilistic methods used for the investigation and design of electric transmission line foundations."

Jan 1, 2017

With the dawning of a new century came the beginning of a new era in the coal industry. Instead of the traditional practice of only buying and selling produced coal in the United States, a coal futures market was established. The New York Mercantile Exchange began trading coal futures in July 2001. But, even in this new era, many of the old is-sues that have beset the coal industry still remain, as was evident in2001. Coal production increased to are cord level during 2001, according to preliminary data from the US Energy Information Administration(EIA). Production in 2001 rose by4% to 1.01 Gt (1.12 billion st), compared with 2000 (Table 1). This barely surpassed the previous record level of 1 Gt (1.11 billion st)set in 1998. Coal consumption remained unchanged. The additional production was used to replenish the depleted stockpiles that had resulted after two years of declining coal production and increasing coal consumption.

Jan 1, 2002

By Marius R. Campbell

VARIOUS classes of coals are recognized in this country at the present time. These classes depend largely upon physical characteristics rather than upon chemical composition, and consequently they cannot be accurately defined. The divisions into anthracite, semi-anthracite and semi-bituminous are fairly satisfactory; but the term bituminous embraces so large a variety of coal that it is of little value, and the term lignite is so loosely applied that it has little or no place in a scientific classification. At present there is no way of accurately defining the vari¬ous classes of coal, because no adequate scheme of classification, which applies to lignites as well as bituminous coal and anthracite bas been proposed. The object of this paper is to present such a scheme, which is based upon data obtained dur¬ing the past year by Prof. N. W. Lord,1 in charge of the chemical laboratory of the United States Geological Survey coal-testing plant at the Louisiana Purchase Exposition, St. Louis. All the classifications of coals proposed prior to 1877 were based either on physical characteristics or on proximate analyses, including all of the impurities. These schemes were illogical and highly unsatisfactory, for the physical properties of a coal give little indication of its true composition; and impurities, such as ash and sulphur, are largely the results of acci-

Sep 1, 1905

By Gordon] [Reavis

Halliburton Services and Brown & Root have developed a unique foundation system that blends oilfield and construction technologies to construct deep foundations which offer significant advantages across a variety of soil profiles. This highly efficient system is being developed to meet the construction industry's needs into the 21st Century. Based on a concept initially introduced to Halliburton Services by V.L. Schellhorn in 1987, Halliburton combined their existing cement slurry mixing and pumping technology with oilfield drilling practices and a new tool design to field test the viability of the concept. Results looked encouraging, and Halliburton asked it's sister company, Brown & Root to evaluate and further develop the process. With Brown & Root's knowledge of the construction industry, the original concept has developed into a viable and efficient foundation construction system.

Jan 1, 1993

By S. H. Ward

Since the advent of the first airborne electromagnetic system, it has been evident that such systems were inherently limited to shallow depths of exploration of the orderof 100 to 200 feet. Hence in 1948 the author and his associates commenced a study of the feasibility of applying natural audio frequency magnetic fields to investigation of the electrical properties of the subsurface in order to provide a system capable of overcoming this limitation. This research culminated, in the summer of 1958, in the development of a new airborne prospecting device — AFMAG. This device has detected surface massive sulphide bodies while flown at heights as great as 3000 feet. Hence, by inference, it is deduced that it could find similar sulphide bodies if they were buried 2500 feet below surface and the aircraft flown at 500 feet. Thus a considerable improvement over conventional airborne electro-magnetic systems is obtainable with AFMAG. Airborne exploration in mountainous terrain involving deep valley fill now becomes possible. Examples are presented of the results of actual airborne AFMAG test surveys over known deposits of massive sulphide mineralization. Interpretation of the data is discussed with particular reference to the knowledge of size, dip, depth, depth extent, and conductivity of causative bodies as deduced from the flight records. The possibility of mapping major geologic structures, for both mining and oil exploration purposes, is discussed with the aid of examples of airborne AFMAG data. INTRODUCTION Electrical prospecting with natural audio frequency electromagnetic waves as a source has, within the last three years, become a practical reality. Both airborne and ground survey instruments under the trademark "AFMAG" (for audio frequency magnetics) have been used successfully in the search for conductive mineral deposits. It is the object of this paper to discuss the principles of airborne AFMAG and to illustrate its application by means of examples obtained over known geological situations. WHY AFMAG? In view of the large number of good airborne electromagnetic systems available for purchase or contract surveying, one may well ask, "Why another new system?". Primarily the answer lies in the fact that AFMAG does not suffer from the very limited depth of exploration available with, and inherent in, any conventional airborne electromagnetic system. AFMAG is not conventional insofar as an artificial transmitter is not required. Only a receiving and detecting device is employed. The electromagnetic fields measured are those from millions of electrical discharges in the atmosphere (e.g;..- lightning strokes). Their random distribution in time and space make these fields difficult to employ and it is only with recent advances in the electronics of geophysical instrumentation that this has become possible. A second reason for AFMAG and one of its

Jan 1, 1961

Jan 1, 1963

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

The author summarizes and extends the relevant results of papers previously published by various authors and presents these results in chart form. The charts are used to demonstrate the theory on a hypothetical mine.INTRODUCTIONRecently a series of articles have dealt with leakage in a mine ventilation system and the problem of its reduction.Theories were developed by Peascod and Keane (1955) for the combined effect of flow in the airways and leakage through the porous barrier between the intake and return of an ideal mine. Later Keane and Peascoa. (1956) extended these ideas to the use of an underground booster fan in increasing the face ventilation and showed how to determine the water gauge and location of the most efficient underground fan.These articles were based on the assumption that Atkin:son's formula:P = R Q2 (1)gave the relation between the pressure drop P lb'/sq. ft., the quantity, Q kilocusecs, flowing in the mine airways and the total resistance, R Atkinsons, to air flow offered by the mine roadway. An Atkinson is defined as a resistance such that 1 kilocusec of air flows due to a pressure drop of 1Ib.jsq. ft. However for conditions prevailing in most mines a more :appropriate relation is that postulated by Reynolds and others (Lamb, 1953) :P=R Qn (2)where n has some value slightly less than 2. It should be noted that Atkinsons may not be used as units when n is not equal to 2.

Jan 1, 1958