Search Documents

By K. Parameswaran, A. Veek, A. Fernandez, P. Safe

ASARCO LLC (Asarco) Hayden Copper smelter, in Hayden, Arizona, has operated continuously (except for minor labor and economic curtailments) since 1912. The current plant configuration comprises INCO flash smelting, Peirce Smith (P-S) converting and fire refining/anode casting. In order to comply with the U.S. Environmental Protection Agency (EPA) 1-hour National Ambient Air Quality Standards (NAAQS) for sulfur dioxide promulgated in June 2010, the Hayden smelter had to increase overall sulfur fixation from approximately 95 % to 99+ %, requiring a retrofit of the existing converter department and upgrade of associated emissions controls systems. The Converter Retrofit Project (CRP) involved replacing the five existing 13’ diameter Peirce-Smith converters (2 blowing, 2 hot standby) with three new 15’ diameter Peirce- Smith converters (1 blowing, 1 hot standby) to allow for more effective process gas capture using the existing acid plant contact section. Significant upgrades were made to the acid plant wet gas cleaning section and converter primary gas handling system to improve capture performance, reliability, and sludge handling. In addition, a new tertiary gas capture system was installed to further minimize fugitive emissions from the converter aisle. The existing furnace tapping ventilation ESP was replaced with a new baghouse to enable at least 50% SO2 removal using high-surface-area dry lime injection, which was also implemented on the existing converter secondary gas baghouse system. The first two converters and all gas handling system improvements were started up in April 2018, and the third converter was brought online in November 2018. This paper presents the regulatory context; genesis and rationale for CRP; detailed description of the project; challenges during commissioning; system improvements implemented, and design considerations made, and systems performance and process optimization achieved since startup.

Jan 1, 2019

By Jean-Sébastien Lambert, Joseph Kabuya, Richard Simon

Managing a highwall failure risk in an open pit mine by controlling and mitigating the impact of vibrations produced by blasting operations is key to achieving safe and cost-effective operations. The impetus behind this study was the risk of multiple bench failures in an open pit mine that was detected by Slope Stability Radar (SSR) following blasting at the foot of a highwall. The unstable high wall was over 140 meters(459.3 ft)high and 200 meters(656.2 ft)wide. The quantity of associated material was estimated at 3,000,000 metric tons(3,306,934 US tons). The overall slope angle was 44 degrees. In order to continue mining without causing the highwall to fail, this study was initiated as part of a risk management plan to mitigate this major risk by identifying mitigation measures related to blasting operations and assessing the response of the rock mass to each blast. Identifying blasting mitigation measures consisted of optimizing blasting parameters to avoid failure of the highwall. First, a signature hole operation was carried out to obtain seismic records that were georeferenced and associated with known single charges. The method used made it possible to determine the propagation velocity of the P-waves associated with the various lithologies studied and to calculate, from the geomechanical properties of the rock masses, the maximum peak particle velocities to be respected. Subsequently, the targeted area of operation was modelled with the I-Blast software in order to optimize the firing sequences to be used according to the different lithologies present. The model also made it possible to optimally predict the particle velocities associated with each blast and ensure compliance with the previously determined peak particle velocity limits. The assessment of the rock mass’s response using SSR consisted of defining alarm thresholds and an intervention plan for various possible alarms as well as quantifying the damage to the highwall from blasting. Controlling the impact of blast vibrations on the highwall’s stability was successful, as the mitigation measures used during mining did not accelerate the highwall’s movement. No upward trend in the stabilization time of the rock mass was observed by the SSR after each blast. Post-blast geotechnical inspections and analysis of post-blast deformations in the highwall also did not reveal significant damage to the highwall as a direct consequence of the blasting.

By Peter Swanson

A seismic monitoring network has been installed in western Colorado (USA) in the vicinity of three underground coal mines to (i) distinguish and characterize seismic activity as either mining related or naturally occurring, (ii) implement a real-time event monitoring and notification tool, and (iii) collect data for use in research studies aimed at quantifying impacts from mining-related and natural seismicity. These potential impacts include dynamic rock mass failures such as coal bumps as well as strong shaking in the vicinity of critical structures such as impoundment dams, reservoirs, mine seals, mine openings, and steep slopes. Examples of two damaging seismic events are presented and the mining and geologic factors attending these dynamic failures are described.

Jan 1, 2008

By Allan Sylvester, Paul E. Gabryszak, Diane R. Hirsch, David P. Field

With construction of the first phase of the Automated People Mover (APM) Tunnels nearing completion, this paper will address how knowledge from recent Tunnel Boring Machine (TBM) and New Austrian Tunneling Method (NATM) tunnel construction at the airport was used to refine the methodology for the next phase of tunnels currently in design. The benefits include an enhanced understanding of the ground conditions; allowing optimization of excavation sequences and support requirements; a more effective instrumentation and monitoring program; and improved construction details and related contract provisions.

Jan 1, 2007

By Jacques Nantel

Mechanization has been at the core of productivity improvements since the industrial revolution. During the past 20 years, mining has derived spectacular progress from mechanization. In the future, however, mechanization alone will not be enough. In the next few decades, automation will bring about new generations of highly productive and safe machines, with low operating costs. Increased use of new and better technology is generally accepted as the prime factor capable of closing the productivity gap. The productivity gap is the difference between inflation and metal prices. The three S-curves in Fig. I represent the evolution of technology in general, and mining in particular. TI represents incremental changes. the dominant sort of technology changes in the mining industry: - Better drills, electric hydraulic drills vs. pneumatic drills, the drilling rate is twice as fast. - Better steel and bits, to accommodate the higher performance drills. - Improved chemical explosives. - Bigger trucks in open pits.

Jan 1, 1993

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL's Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, B. D. Ganesh Shetty, M. RAJU

The production of high strength iron ore sinter for blast furnace iron making unit was developed by optimizing the granulometry of less than − 0.150 mm fines in sinter base mix which consists of iron ore fines (− 10 mm size with 0.150 mm: 41%), beneficiation plant jig concentrate, i.e., washed ore (− 3 + 0.150 mm size with − 0.150 mm 3 to 9%), beneficiation plant concentrate (− 0.150 mm size 97%), limestone, dolomite, coke breeze, lime, sinter return fines, direct reduced iron (DRI plant) fines, and micropellets produced from steel plant waste. The sintering process consists of preparation of base mix, mixing, and production of nodules using mixing and nodulizing drum by maintaining the optimum moisture, transferring of nodules to the sintering machine, and firing of sinter by applying optimum suction pressure. To optimize the < 0.150 mm fines in sinter base mix, the − 10-mm size iron ore fines was replaced with washed ore. The size analysis, granulation index (G index), and optimization of moisture w.r.t. sinter bed permeability were carried out by varying the washed ore addition from 0 to 55% in sinter base mix to vary the − 0.150 mm fine size. With decrease in washed ore addition from 55 to 0% in sinter base mix the finer fraction, i.e., − 0.150 mm in sinter base mix increased from 9.4 to 26.7%. Granulation (G) index increased from 1.46 to 3.10, sinter bed permeability increased from 33 to 53 Japanese Permeability Unit (JPU), and balling index increased from 1.4 to 3.0. With increase in − 0.150 mm fines in the sinter base mix from 9.4 to 26.7%, the sinter tumbler index (T.I) increased and sinter reduction degradation index (RDI) decreased. Increase in sinter strength and decrease in sinter RDI was due to increase in formation of Silico ferrite of calcium and aluminium (SFCA) phase and decrease in pore phase. The SFCA is the main bonding phase in iron ore sinter, and it provides strength to sinter. Sinter base mix with − 0.150 mm fines 18.9% (washed ore addition 25%) achieved desired sinter properties with moisture 8.0%, G index 2.44, balling index 2.3, and sinter bed permeability > 45JPU. Decreased the sinter properties with washed ore addition in sinter base mix beyond 25% due to decrease in − 0.150 mm fines in sinter base mix. Further, to improve the sinter properties with washed ore 30 to 45%, 3 to 10% beneficiation plant concentrate, i.e., − 0.150 mm fines was added to maintain the 18.9% of − 0.150 mm fines in sinter base mix. From the laboratory sintering studies, it was found that minimum 18.9% (range from 18.9 to 26.7%) − 0.150 mm fines should be maintained in the sinter base mix to achieve desired sinter properties.

Oct 16, 2021

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

The dynamic response of holdup in a continuous ball mill has a direct influence on the rate function of grinding kinetics and is useful for predicting the variation in the size distribution of the finished product with time.A model was proposed involving three interacting, completely mixed chambers and this was used to derive analytically the transfer function of the system, from which the unit impulse response and the unit step response of the holdup with feed rate were obtained.The theory was confirmed by comparing it with previously published experimental data for the residence time distribution of particles passing through a ball mill.

Jan 1, 1975

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo&apos; where svo&apos; is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By Darren Thorton, David Sprott, Ian Brunton

Blasting causes movement of the rock and can be detrimental to the accurate delineation of the ore and waste regions within the resulting muck pile. The consequences can be ore loss and dilution. However, ore loss and dilution can be minimized and significant increases in profit can be realized if the movement can be accurately measured. Various methods have been used to measure muck pile movement including poly-pipe, chain and sandbags but these have been either inaccurate or impractical. The Julius Kruttschnitt Mineral Research Centre, JKMRC, has developed an electronic blast movement monitor that provides accurate three-dimensional movement vectors following a production blast. From this information, the ore block boundaries in the blasted bench can be adjusted to compensate for the measured movement and then ore recovery can be optimised. Following initial development of the prototype technology, the JKMRC further developed and demonstrated the system in actual production blasts at an open pit gold mine operated by Placer Dome Inc.

Jan 1, 2005

By J. Sammarco

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to determine if light-emitting diode (LED) cap lamps can improve safety by reducing glare. Glare can impede a miner?s ability to see hazards and to safely perform their work. Another objective is to determine if a person?s age is a factor. This is important because the workforce is aging ? the average miner is now about 43 years old. Three cap lamps were used to evaluate glare: an incandescent cap lamp, a commercially available LED cap lamp and a NIOSH prototype LED cap lamp. Thirty NIOSH personnel from the Pittsburgh Research Laboratory (PRL) served as test subjects. Three age groups were established with ten subjects in each group. Testing was conducted in the Mine Illumination Laboratory (MIL) of NIOSH PRL. The results indicate no statistically significant difference in discomfort glare among the incandescent and LED cap lamps. However, an analysis of variance for disability glare indicates that the LED cap lamps were superior for the older subjects. Disability glare scores for the oldest subject group improved 53.8% when using the NIOSH prototype LED cap lamp compared to the incandescent cap lamp and 36.5% compared to the commercial LED cap lamp. It ap­pears that, given the conditions of this study, LED cap lamps will not increase discomfort glare and can enable significant improvements in disability glare for older workers. It is also evident that not all LEDs are created equal. The disability glare improved the best for older workers when they used the NIOSH prototype LED cap lamp, which has a different spectral power distribution (SPD) (more short wavelength energy) than the commercial LED cap lamp. Therefore, for disability glare, the results suggest that the SPD is an important factor to consider in cap lamp design.

Jan 1, 2009

By J. Girard-Dwyer, T. Camm

Direct costs such as medical, legal, administrative, and worker’s compensation costs, property damage, lost earnings, and lost benefits are typically used to compute the economic impacts of occupational injuries. However, there are also a number of less obvious, indirect costs that substantially contribute to the overall loss costs. In fact, for every $1 of direct costs an estimated $3 to $5 of indirect costs are also incurred. This paper presents a systems approach that incorporates engineering, economics, psychology, and sociology in order to evaluate the total value of investments in safety. By studying the interrelated system comprised of the injured worker, their family and coworkers, as well as the organizational structure that was the setting for the incident, a methodology can be developed that will more accurately capture the true costs of mine injuries.

By W. F. Netzeband

This paper, which describes mining methods and practices at the Rialto zinc-lead mine American Zinc, Lead & Smelting Co., in northeastern Oklahoma, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States, The Rialto mine is in the SE1/4 SW1/4 sec. 20 and the NW1/4 sec. 29, T. 29 N., R. 23 E., Ottawa County, Okla. (fig. 1). The 200-acre property is southwest of and adjacent to the town of Picher in the central part of the Picher field of the Tri-State zinc-lead mining district (fig. 2). Other mines of the company adjoin the Rialto on the east and south. Zinc-lead ores have been mined almost continuously from the Rialto tract since 1916. The property was acquired by American Zinc, Lead & Smelting Co. late in 1951, and the mine was operated thereafter by the Nellie B Division of that company until the end of 1955, when it was subleased to the Residue Mining Co.

Jan 1, 1958

"The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are:1. Line Drilling2. Cushion Blasting3. Smooth Wall Blasting4. Buffer Blasting5. Presplitting or Preshearing6. Air Deck Presplitting"

Jan 1, 1994

By Steve Colbum

LTl’s MapStar LPS (laser positioning system) utilize both tripod mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environment characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, interactive software program, which can be run on any standard PC. Win Prof, the Windows-based analytical software package is used to reduce the data for generating bench face profiles, surfaces, volumes, estimating true burdens and mining ratio calculations. In addition, the software has many other built-in routines to calculate powder factors, toe shear, to map structural contacts and to predict the flyrock potential based on the Burden to Energy ratios. An extensive, built-in library of explosive’s data facilitates these calculations. It will also conform automatically to user-specified minimum and/or maximum burden in relation to the explosive energy, hole diameter and bench geometry - for both vertical and inclined holes. Numerical data can be represented in 2D or 3D to emphasize the hole-burden-face relationships.In this workshop, the MapStar LPS instruments and Win Prof analytical software will be thoroughly demonstrated. Demonstrations include equipment configuration, typical field setups and several effective survey procedures, including processing of some sample data.

Jan 1, 2000

By Badiozamani Khosrow

Introduction The mining industry has been using computers since the late 1950s. Despite this early start, the use of mine planning software is not a common practice in many operations. But the trend might be changing because of the availability of relatively inexpensive personal computers (PC). The introduction of these machines has generated unprecedented interest by mine managers to computerize their planning operations. However, some managers have become disappointed with the PC&apos;s lack of adequate software and the inability to handle the massive amounts of information required for modeling. This paper is an attempt to shed some light on the future of computers in the mining industry. It will examine: • historical progress in the computer industry, • future advances in the computer industry, • historical usage of computers in mining, and • future alternatives available to mining. Historical Progress The computer industry has come a long way since the first full-fledged electronic digital computer Electronic Numerical Integrator And Calculator (ENIAC) was built in 1946. This machine weighed more than 27 t (30 st). It contained 19,000 vacuum tubes, occupied 139 m2 (1500 sq ft), and could perform 5000 additions per second. By contrast, today&apos;s fastest, commercially available computer is the CRAY-X. It weighs less than 5 t (6 st), has no vacuum tubes, occupies less than 9 m2 (100 sq ft), and performs over 100 million operations per second. This is an incredible advancement in less than 40 years. One person commented on the rate of advancement in the computer industry. He suggested that if the auto industry had advanced at the same rate as the electronics industry, we could buy a Rolls Royce for $2.75 and it would run

Jan 9, 1984