Search Documents

By Edwin G. Sharp, Frank S. Gaunce, George M. Freeman, Denis J. Kemp, Eric Dulson, Paul Salmon, Ernest R. Hamilton, Carl E. Parden

"THE ECSTALL ZINC PLANT was built for the treatment of the Kidd Creek zinc sulphide concentrates. Construction proceeded throughout 1970-71, with operations beginning in April 1972. The two concentrate types treated differ principally in minor impurity and precious metal contents. Processing flexibility was required to allow efficient recovery of the by-products, especially cadmium, copper and silver. The conversion of the zinc sulphide concentrates to end products follows a sequence of operations that are common to most electrolytic zinc plants and typical of the ""Tainton- Jephson"" flowsheet.1. Roasting in air at an elevated temperature to convert the metal sulphides to soluble metal oxides (calcine) and sulphur dioxide. The sulphur dioxide is converted to sulphuric acid in a contad plant and shipped by train to market.2. Leaching of the calcine in spent electrolyte to effect extraction and recovery of zinc as zinc sulphate solution, leaving an insoluble residue.3. Purification of the clarified zinc sulphate solution by cementation with metallic zinc dust to remove impurities detrimental to the electro-deposition of zinc or detrimental to product purity. The solids from cementation are the starting materials for secondary metal recovery.4. Electrolysis of the purified zinc sulphate solution to reduce the zinc to the metallic state while coincidentally regenerating the sulphuric acid for recycle to the leaching step."

Jan 1, 1974

By Alfred Traverse

The Brandon lignite is a small deposit of very low rank coal near the village of Forestdale in the town of Brandon, Vt. It occurs in association with other sediments, principally sands and silts. This lignitic coal has attracted considerable scientific interest since the middle of the 19th century because of the abundance of fossils in the sediment and the rarity of lignite in New England. A cooperative investigation has been developed by E. S. Barghoorn, W. Spackman, and the author in which different phases of the problem have been worked on in a coordinated research program. This paper presents results of an investigation of the very abundant fossil pollen and spores and some other microfossils of the deposit. The studies on which this manuscript is based were made in large part at Harvard University in partial fulfillment of the requirements for a Ph. D. degree.

Jan 1, 1955

By Basil B. Zavoico

The production of all Russian fields incressed from approsimatctly 74,000,000 bbl. during 1926-27, to approximately 83,000,000 bbl. during 1927-28. Of this amount Baku was responsible for 54,.500,000 bbl., Grozny for 25,800,000 bbl., and Emba for 1,200,000 bbl. Accordingly, the proportional importance of the Grozny oil field has been considerably increased, the present production being twice that of 1913. The most notable factor of production during 1927-28 was the importance of gushers; 40.8 per cent. of the total was thus obtained. In the Baku fields 26 per cent. of the total, and in Grozny 74.2 percent'. of the total were produced by naturally flowing wells. This may be explained by the reduction in authorizations for drilling by the central authorities, and, accordingly, the local trusts increased the production to the planned figures at the expense of the proved prolific reserves. In Baku region, the Surnkany oil field produced 36.1 per cent. of the total Baku production, or an equivalent of 53,800 bbl. per clay, the largest percentage coining from the fifth horizon. Nest year's plans call for continual development of that horizon as well as of the sixteenth horizon in the Bibi-Eibat field, which was opened lately. In the Grozny fields the New Area (Bellik) WAS responsible for 79.4 per cent. of the total production. The authorized plan for 1928-29 production calls for 92,200,000 bid., and a reasonably accurate estimate for 1932--33 production is placed at. 156,000,000 bbl., with Baku contributing 101,800,000 bbl., Grozny 44,100,000 bbl., Emba 6,200,000 bbl., Kuban 2,100,000 bbl., Saghalien Island 1,400,000 bbl., and Russian Turkestan 400,000 bbl. In connection with recent discoverices in the Baku area these figures art. quite conservative. The average production per well per day in the Baku oil fields was 49.2 bbl., in Grozny 175 bbl.; in detail, Surakany oil field averaged 250 bbl., and the New Area in Grozny 514 bbl. per day. New completions in all Baku fields averaged 264 bbl. per day, and in Grozny 970 bbl. pel. day. These figures show a considerable progress in the technical developnlent of all fields, compared even with the prerevolution figures, since all the mprovements are noted in the fields that arc over 30 years old.

Jan 1, 1929

By Junji Shibata

It is important to recover and reuse the metal values contained in various industrial wastes in a viewpoint of environmental preservation. Most of industrial products are made through the processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. In this paper, some examples of the application of solvent extraction to the treatment of wastes are introduced. The treatment of solid wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse water, etching solution and pickling solution are accomplished using solvent extraction technique.

Jan 1, 1996

By J. R. Alldredge

This Bureau of Mines report presents a computer code that has been developed for describing and testing the statistical distribution of general continuous data sets. The statistical distributions used include the normal, lognormal, exponential, chi square, gamma, and uniform. Histograms for observed and expected values are plotted for each distribution. An example using geologic data obtained from a study of the geometric properties of natural fractures in oil shale rock illustrates the use of the computer program, GDIST.

Jan 1, 1977

By P. K. Chatterjee, G. D. Just

Sublevel open stoping is a low-cost method that has been successfully employed in many large underground mining operations. Where ore body characteristics are suitable, extensive mechanization and the use of large-scale stoping techniques can considerably reduce operating costs. However, careful long-term planning of mine layouts and large capital commitments in development are required prior to production. Implementing precise mine design procedures and carefully controlling operations can result in considerable benefits. This article describes methods to achieve these objectives based largely on mining operations at Mount Isa, where sublevel open stoping has been used since 1932. Ore won by this method accounted for a very large percentage of the total tonnage produced at Mount Isa. Major costs associated with sublevel open stoping can be classified as drilling, explosives and charging, and LHD costs. In this article, analyses of these costs are made with particular reference to stope design. Parameters such as burden, drill hole diameter, explosive density, specific charge, etc., are considered in establishing the interrelationship of unit operating costs, as well as total costs of sublevel open stoping.

Jan 10, 1981

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By Jerry C. Tien

In 2009 China mined 2.695 billion metric tones (Gt) of raw coal. It is estimated that only 3-5% or roughly 135 million metric tones (Mt) of these were mined from 300 some surface operations. Except for a dozen or so large modern operations, most of China's surface coal operations are small by western standards, with annual production ranging from a few thousand tones to 300,000 metric tones (mt). Depending on the size of operations, equipment used range from small trucks and shovels to large bucket wheel excavators and draglines in sizable pits. This article provides a brief overview of China's surface mineable coal reserves, mining methods commonly used and increasing environmental concerns; introductions of several large surface operations are also provided.

Jan 1, 2012

By M. Botz

Alacer Gold Corporation is constructing the Çöpler Gold Mine in eastern Turkey. Mining commenced in the fourth quarter of 2009 and gold production started in the fourth quarter of 2010. The mine is a 15,500 t/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production, but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life, approximately 40 Mt of ore will be placed on the leach pad, which will contain about 35,000 t of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the life of the mine. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By Tim O’Neil

More than 5,300 mining professionals from around the world attended the SME Annual Meeting and Exhibit, March 1-3 in Denver, CO. Seventy three technical sessions highlighted innovative technologies and applications for the development of mineral resources. And the exhibit featured 421 companies worldwide and 632 exhibit booths. The 1999 SME Annual Meeting had 10% international attendance. Professionals from outside the United States were guests at the first SME International Reception.

Jan 1, 1999

By Tad Crowie, Victor Delgado, Nick Katsikaros, Tim Hughes

"A number of silver producers have identified a need for a system to recover silver and gold from base metal flotation concentrates on site rather than sending the concentrate to third party smelters to improve mine economics. Historically intensive cyanidation has only been used for coarse gold gravity concentrates in batch machines but Gekko have applied the InLine Leach Reactor (ILR) to these difficult to leach concentrates.The ILR’s unique ability to operate at various solid to solution ratios, high mass capacity, the ability to handle fines, the use of peroxide to aid silver leach kinetics and simple operation has resulted in significant economic benefits to Hochschild PLC’s Selene and Arcata operations. This paper describes the commissioning phase of the ILR5000BA intensive cyanidation reactors on concentrates from the Selene mine at the Ares Concentrator.INTRODUCTIONIntensive leaching of high grade concentrates in gold ore treatment is now commonplace and is considered an essential feature of most gold circuits (Lane, Fountain and LeBrooy, 2008). The devices commonly used for intensive leaching (InLine Leach Reactor, Acacia Reactor, etc) are specifically designed for the typical coarse nature of the concentrate.In some of these intensive leach applications, significant amounts of silver are co-recovered with the gold. In fact, the intensive leaching conditions of 1 to 2% NaCN in solution and high dissolved oxygen levels, overcome the issue with silver’s slow dissolution rate in traditional CIL/CIP circuits and avoids the formation of insoluble silver sulphide minerals on the surface of the gold (Marsden, 2006).There are a significant number of mine operators producing silver in the form of mixed base metal sulphides flotation concentrates. Typically the mine operators are paid for the silver after processing of the concentrate by the base metal smelter whom recovers the silver during the refining process."

Jan 1, 2010

By Nathan C. Rockwood

WHILE mining engineers have been searching in far corners of the country and of the world for hidden wealth there has grown up around us in nearly every city great wealth-producing mines calling for the investment of hundreds of millions of dollars and yielding products now sold for over half a billion dollars yearly-largely unknown and almost wholly neglected by mining engineers. But this neglect is explainable and excusable. They are industries of very recent origin-practically the growth of the last 25 years. They are in a very large measure the result of tremendous developments in engineering construction and the rapidly expanding use of portland cement concrete for structures of every description. Concrete as a material of construction is going through an evolution very much as did cast iron and other metals used in engineering; and this phase of the industry should appeal to the imagination of metallurgical engineers. At first iron was iron-a material of uncertain properties, owing both to small differences in chemical composition and in methods of manufacture. By successive steps iron was studied and knowledge of its properties developed-the striking effects of very small percentages of other minerals and of various heat-treatments.

Jan 1, 1924

By Stavros A. Argyropoulos

Exothermic mass transfer takes place in various areas involving metallic systems, ranging from liquid metal processing operations to the growth of thin films in microelectronics. The formation of intermetallic compounds plays an important role in the exothermic mass transfer of metallic systems. Two types of exothermicity are identified , namely , Microexothermicity and Macroexothermicity. The former is encountered when small amounts of metals are mixed, while the latter is exhibited when a solid metal in a lump form is added into liquid metal. In this paper two types of exothermic mass transfer in metallic systems will be presented and reviewed. Mathematical modelling work for these types of exothermic mass transfer will be analyzed.

Jan 1, 1993

By J. -C. Sztuke, M. Cao

ABSTRACT The correlations between froth recovery of coal and air recovery were investigated using a hybrid mechanical flotation column. The particle slurry was fed onto the surface of air-water two phase froths to carry out the tests. Froth recovery was taken as the recovery of particles into the froth product, whereas air recovery was determined by the froth height method. The relationships between froth recovery and air recovery were nearly linear, with greater slopes for more hydrophobic particles. Inside the froth phase, the particles were stratified, with hydrophobic particles concentrated in the upper region and hydrophilic particles in the lower region.

Jan 1, 2013

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By John Birkinbine

(Wilkes-Barre Meeting, June, 1911). MODERN advances in practically all lines of industrial development have occurred in such rapid succession, and have been accepted so readily as accomplished facts, that a retrospect surprises us, by showing how comparatively few of the acknowledged factors of improved conditions may be considered as old. While these advances have not been confined to any country, they have been more pronounced in some than in others, and nowhere more so than in the United States, the population of which, having multiplied nearly three-fold between 1870 and 1910, demanded a proportionately greater increase in materials, supplies, and manufactured products. It therefore appears desirable to discuss mainly conditions in the United States, as concrete evidence of industrial progress throughout the world. Looking backward for but three generations, we may trace the introduction and development of canal- and steamboat-navigation; railroad-transportation; artificial illumination beyond that furnished by candles and lard-oil; quick communication by mail, and subsequently by telegraph or telephone; the manufacture of iron, beyond forms of small dimensions; the production and utilization of steel in large quantities; the economic use of mineral fuel, oil and gas, etc. The practical coincidence of the fortieth anniversary and the 100th technical meeting of the American Institute of Mining Engineers, offers temptation to recall and compare the conditions of mining and metallurgy in or about the years 1871 and 1911. A complete resume would cover phenomenal changes in mining-methods and equipment by which the output of individual exploitation has grown from scores to hundreds and even thousands of units in equal time-intervals. Extension of operations in depth and area, demanding machinery of great power

Aug 1, 1911

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

By P. A. Cox

The purpose of the initial research performed under this contract was to determine the margins of safety in explosion-proof (XP) enclosures, which were designed and certified according to the current schedule (Schedule 2G). Results from this work provide baseline data on the current schedule, from which a new schedule can be formulated to give equal or greater levels of safety. Results and discoveries in the initial work led to an expansion of the contract to cover, additionally, weld quality in enclosure fabrication, reliability of enclosures with windows and lenses, and performance tests for enclosure qualification. Finite element calculations and hydrostatic tests revealed wide variations in the margins of safety in the enclosures studied; however, only one enclosure had a safety factor which was less than one. Results from a weld quality survey led to the recommendation of AWS Welding Standard D14.4 for the fabrication of XP enclosures. Based on other work, accelerated aging tests were recommended for qualifying plastics and adhesives that are used in some enclosures, and a Structural Performance Test was developed to test enclosure strength for a minimum static pressure of 150 psig.

Jan 1, 1982