Search Documents

By Giannini M

Of the optimization techniques proposed in determining the optimum open pit limits, dynamic programming and graph theory have proved most successful. However, publications on these two methods lack a certain amount of rigour and clarity in exposition. Certain ideas in the methods have been clarified and additional features introduced in order to make them more sensitive to practical applications. A case study in the form of an application of these ideas on data from a producing mine is presented and discussed.

Jan 1, 1986

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By F. E. Joyce

This paper describes the development of a process for producing manganese and iron pellet concentrates from low-grade manganiferous iron ores of the Cuyuna range by a two-stage sulfatization-reduction roast. First, the manganese minerals (7.5 percent manganese) were converted to water-soluble manganese sulfate by roasting in sulfur oxide gases at 700° C, then, the hematitic iron minerals (31 percent iron) in the hot sulfatized are were reduced to magnetite with simulated reformed natural gas in the temperature range of 350° to 425° C. Batch tests were made in a 3-inch-ID by 6-inch-long, gas-heated, stainless steel retort, and continuous countercurrent experiments were performed in a 2-inch-ID by 10-foot-long, electrically heated shaft furnace. Manganese sulfate was removed from the roasted product by leaching with water, and over 90 percent of the manganese was recovered in an oxide product (65 percent manganese) obtained by precipitation, drying, and thelmal decomposition of the sulfate. An iron oxide concentrate (60 percent iron) with an iron recovery of 75 percent was obtained from the water-insoluble residue by magnetic separation.

Jan 1, 1973

By Jr. Gabler

Because of concern over the availability and reliability of an uninterrupted supply of manganese and other materials, the U.S. Congress requested that the U.S. Bureau of Mines (USBM) study the /low of strategic and critical materials in the economy to delineate and quantify the production areas where metal values are lost. As a result, the USBM developed a generic computerized commodity flow model that is readily amenable to updating. The original model developed for cobalt, with slight modifications, was used to track the flow of manganese. This report follows the flow of manganese through its metallurgical and chemical applications and highlights areas where significant losses occur owing to downgrading, export, or disposal. The study indicates that materials containing 695,000 short tons (st) of manganese were consumed domestically in 1990. Scrap recovery specifically for manganese recycling was insignificant. However, considerable manganese was recycled through processing operations as a minor component of ferrous and nonferrous scrap and steel slag. The major loss category is manganese lost in steel processing, 323,156 st or 46 pet of the 1990 apparent consumption. Most of this loss reports to steelmaking slags. Recovery from slags is technically feasible, but is not economically feasible.

Jan 1, 1995

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By Roy A. Grancher

Construction materials indeed face a dilemma...as does the building industry as a whole. A stop & go economy; a severe drop; in housing starts; lingering indecision over just what corrective steps are to be taken or to their degree of commitment; no less basic disagreement in regard to which of the, Nation's problems is really the most pressing -- inflation or recession? Optimism has become a rare quality these days. At moat the cautious view is that this new year will see a long, hard struggle back, with hopes that 1976 at least can truly mark a dual anniversary celebration for the United States and its economic health. Yet the paradox is that once recovery does return, those very construction minerals and materials --which in recent years have experienced the ups and downs of overcapacity, shortage, and now declining demand again-- will once more face the spectre of mass inability to service revived and growing needs for its product. Mounting costs, present marginal expansion investment, and substantial lead times required for new facilities to come into production, could well form a bottleneck to economic upswing. The result again can be another cycle of shortage-induced inflation, and with it continued gyrations within the demand supply relationships of the country's building industries.

Jan 1, 1975

By J. L. Viljoen

t has long been the drive of the industry and all operations to create an environment that is free of injury and illness. We have come a long way; the leaders, executives, managers, supervisors and workers are to be commended for relentlessly driving to create, what I call a ?White Flag Day Every Day?. Yet I am also aware of the huge shift we still need to create in the industry, on the operations and in the workplaces to have them free of injury and illness. Keywords People, values, care, trust, belief.

Jan 1, 2011

By Klaus Rieker

North of Antwerp central train station, two single-track tunnels for the high-speed train line between Brussels and Amsterdam were constructed. At the same time, the central train station was modified to a through station. Both 1.23 km tunnels are situated in the Antwerp sands and were constructed using a slurry shield machine. Due to the inner city location, the tunnels run over their entire length underneath structures, in some cases with only minimal clearance. The paper deals with these challenging situations. In addition, the tunnel boring machine, the tunnel lining and measures to limit settlements will be introduced.

Jan 1, 2007

By Sam Bang Jr, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine’has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to sot? material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessaryas vertical presplit drilling produced wall failures.

Jan 1, 1998

"WELCOME/BIENVENUE TO THE COM 2014 IN BEAUTIFUL VANCOUVER!On behalf of the organizing committee, I would like to extend my thanks to you for participating in this year’s Conference of Metallurgists. Recent times have been extremely difficult for the resource sector, but it is crucial for our industry to maintain personal connections through good and bad times. These interactions include technical exchanges, and this is at the heart of MetSoc’s service to its members. The theme of this 53rd Conference of Metallurgists is Prosperity Through Process Advancements. There are thirteen symposia at this year’s conference mainly focused on processing from extractive fields, to materials and the environment. Supporting these topics are the plenary, poster session, and trade show plus opportunities for socializing at functions like the opening reception and the awards banquet.Many people have contributed to this conference, from the authors and presenters to the organizers and the generous sponsors. They are all gratefully acknowledged for their quality work over the last two years. A particular thank you to our student volunteers whom we hope will take advantage of their time at COM to network and to learn about this exciting industry.Again, thank you for being a part of this exciting conference of metallurgists. I hope it will be a memorable experience and that you are able to take advantage of all the conference and Vancouver have to offer."

Jan 1, 2014

By Both R. A, Daily B

The Patawarta Diapir, located in the northern Flinders Ranges (South Australia), has intruded into late Proterozoic Wilpena Group sedimentary rocks. The diapir contains disrupted blocks of a wide variety of rock types, most of which can be correlated with the Lower Callanna Beds of Willouran age, in a matrix of predominantly carbonate and siltstone breccia. Mafic rocks in the diapir appear to predate intrusion of the diapir. As with many other diapirs in the Flinders Ranges, copper mineralization is present in the diapir and occurs as narrow veins consisting essentially of carbonate with chalcopyrite and pyrite that formed after diapiric intrusion.Fluid inclusion studies demonstrate that the mineralizing fluid was a Na-Ca-K-Cl brine; probably derived by expulsion of interstitial water following emplacement of the diapir, with dissolution of evaporites within the Callanna Beds sediments and enrichment in copper by reaction with these sediments and associated basic igneous rocks. Mineral assemblages combined with fluid inclusion and geochemical data indicate a possible environment of vein formation of T ÿ 165°C, pH ÿ 4.3 ± 0.9 and log fO2 ÿ -47.3 ± 0.5. Sulphur isotope analyses indicate d34Sfluid ÿ 10 per mil, suggesting evaporites in the Proterozoic sediments as the major source of the sulphur but with some additional sulphur from an igneous source, possibly leached from the malic rocks of the diapir.

Jan 1, 1986

Recovery of Fine Gold Particles from Philippine Gold Deposits by Enhanced Gravity Concentration and Flotation The objective of the study is to determine the applicability of enhanced gravity concentration (EGC) and flotation for gold recovery. While gravity concentration methods have long been applied to gold ores, especially to free-milling types that requires minimal beneficiation, flotation for gold recovery has not yet taken hold as a major operation in the Philippine setting. In this study, the application of EGC and flotation for gold is applied and compared to the existing methods for gold recovery. Two samples, with assays of 7.315 and 5.333 g Au/MT (samples 1 and 2, respectively) are used for this study. These samples are subjected to mineralogical studies and is found to have a gold-particle size ranging 10 to 200 microns. To verify the separation size, the mesh-of-grind (MOG) is used as the primary parameter for experimentation. Initially, the samples are stage-crushed, ground, and subjected to EGC using a Falcon SB40 Concentrator. Based on the results, the two samples showed that recovery increases with a finer MOG. The ratio of concentration (K) decreases with a finer MOG. This shows that there should be sufficient liberation of the gold values for EGC to be effective. The effect of the enhancement is to pronounce the difference in specific gravity of the minerals, promoting better separation. This is validated by the high recovery values of 86.97 per cent and 98.73 per cent exhibited respectively for samples 1 and 2 (at 54 microns). For the flotation runs, sample 2 with an average particle size of 80 per cent passing 74 microns is examined using thiocarbamate-based collectors for roughing and subsequently exhibited a recovery of 96.32 per cent. At this point, the concentration ratio (K) is noted as an important efficiency indicator for flotation process since it yielded a very low-mass and high-metal content concentrate.

Sep 13, 2010

By S. Sunkavalli

Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction, and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation. Key words: Arsenic sulfides, oxidation, shrinking core, waste rock, oxygen transport

Feb 27, 2013

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014

By F. Habashi

The changes that took place in China between 1984 and 2004 are remarkable. Visits were made to universities, research institutes, metallurgical industry, and many cultural centers within five trips during this twenty years period. The impressions of these visits are outlined.

Jan 1, 2007

By Steve Polegato, J. Coady Marsh, Gary Landry

The Donkin-Morien Mine in Cape Breton, Nova Scotia, has successfully completed the excavation of a 7.6m (25-ft) diameter access decline over a distance of 3.5km out under the Atlantic Ocean. The tunnel, completed in December 1984, was driven through a sedimentary sequence of sandstone, siltstone, mudstone and various gassy coal seams prior to intersecting the Harbour Coal Seam where development work will commence. The tunnel was driven by a Canadian prototype tunnel boring machine (TBM) manufactured by Lovat Tunnel Equipment, Inc., Toronto, Ontario. The 7.6m (25-ft) diameter full-face shielded TBM operated at various grades from 0-20%. This paper outlines the TBM design, excavation, support and backup system utilized in the drivage. Problems encountered and drivage rates will be addressed.

Jan 1, 1985

By John A. Herbst, Alexander Potapov, Xiangjun Qiu

"High Fidelity Simulation is a name applied to the use of first principles modeling tools including Discrete Element Modeling (DEM), Computational Fluid Dynamics (CFD) and Discrete Grain Breakage (DGB) to mathematically describe and study processing systems. Over the past few years, significant advances have been made in High Fidelity Simulation applications, particularly as many mineral processors have been drawn to the study and use of DEM of grinding mills for optimization purposes. This presentation provides an introduction to High Fidelity Simulation, with an emphasis on DEM. It will include insights into current applications of these tools including the optimal design (wear and throughput) of mill lining systems and media selection, the analysis and design (flow and efficiency) of the back-end of grate discharge mills. Advantages of full mill simulations versus individual sub-process simulations will be demonstrated for a SAG mill with different discharge system designs.INTRODUCTIONHigh Fidelity Simulation is providing mineral processors with the opportunity to analyze the behavior of mineral processing equipment from a fundamental or microscale point of view. In the past complex phenomena such as tumbling mill grinding had to be analyzed using black box tools such as residence time distributions for transport and classification functions for passage of particles through grates; while breakage had to be analyzed using PBM models who derived their form from theory but required direct measurement of kinetics. Today with the help of DEM, CFD and DGB these can be analyzed at a very fundamental level.The key element of DEM simulation is the application of Newton’s laws of motion to individual objects or discrete elements. Using this simulation method one can describe the position, velocity (both translational and rotational) of all objects and the transfer of momentum to other objects (Mishra and Rajamani, 1992; Cleary, 1998; Nordell et al, 2001)."

Jan 1, 2003

By P D. Katsabanis

This chapter describes the principles for the derivation of the equations for a detonation wave. The importance of the equation of state for the detonation products is demonstrated and commonly used equations of state are discussed. Furthermore a brief introduction to the TIGER code is presented.

Jan 1, 1991

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2005

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002