Search Documents

By B. M. Larsen

Jan 1, 1948

By B. M. Larsen

Jan 1, 1948

The ore, as sent to the sulphide mill, is a mixture, in varying proportions, of oxidized ore from above the 450-ft. level and sulphide ore from above and below (to date mainly from above) that level. The oxidized ore consists essentially of quartz, with varying amounts of kaolin and clayey material which passes into the slime and, in excess, creates a serious problem in settling. Pyrite may be present in small amounts. The gold is free and extremely fine.The ore, classed as sulphide, consists of pyritic material in a quartz gangue. The sulphides have been exposed to weathering, leaching by descending solutions and attack by ascending gases and actual burning. The alteration products occur in widely varying proportions and this variation adds to the difficulties in settling and control of grinding and flotation.Copper Minerals.-Chalcopyrite is the principal copperbearing mineral with smaller and varying amounts of covellite, which is sometimes associated with chalcocite, both these minerals being apparently of secondary origin.Examination of tailing by Dr. Stillwell has revealed all stages between clean chalcopyrite, chalcopyrite tinged with covellite, covellite with residual cores of chalcopyrite and clean covellite.The chalcopyrite is free floating, very few particles of clean chalcopyrite being observed in the tailing from granular flotation. The chief tailing loss is probably as chalcopyrite occurring as small inclusions in pyrite...

Jan 1, 1939

By J. A. Woolf, A. P. Towne

"INTRODUCTION A considerable part of the metallurgical work of the Precious Metals Section comprises ore-testing experiments on ores selected as representative of various mining districts on areas. Projects authorized by the Bureau and assigned to the Precious Metals Section generally include only those ores or tailings in which the precious metals are the main valuable constituents; however, there are also included ores that contain strategic or critical metals in addition to the precious metals. The recovery of strategic and critical minerals is the most important phase of the treatment of this latter class of ores. However, if a considerable percentage of the precious-metal content of such ores can be recovered without complicating the flow sheet too much, it may be possible to treat an ore for the recovery of strategic or critical metals that could not otherwise be treated at a profit.Standard testing procedure involving cyanidation, amalgamation, gravity concentration, and flotation, or a combination of these methods, is employed in the greater part of this work. However, as the complexity of the ores furnished for this work has increased, it has been necessary to include special applications of standard procedures in many instances, Standard methods of conducting tests and the purposes of the work as a whole have been discussed in previous reports 4/ of ore-testing studies. In the present report, whenever it has been necessary to apply some special phase of standard treatment, this has boon explained in detail in that particular section of the report."

Aug 1, 1944

By P. A. Witt

"Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located 75 km southwest of Kamloops, British Columbia (Fig. 1).The ore is situated within a porphyry copper deposit and is mined at a rate of 135,000 mt/day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 people and is planned to operate until 2009. The operation is a partnership between Teck Cominco (63.9%), BHP Billiton (33.6%), and others (2.5%). Management is shared by the two principal owners and directed by a management committee."

Jan 1, 2005

Lime-enhanced carbothermic reduction may provide an alternative process for treating low grade chalcopyrite concentrates. To date, most research on lime-enhanced reduction has been on pure, synthetic sulfides. In this study, preliminary experiments were carried out on natural chalcopyrite using a thermal analysis system to assess the rate and extent of reaction at several temperatures and identify the major solid and gaseous reaction products. Calculations were performed to establish the thermodynamic limits of the reactions in the temperature range of interest in order to identify the potential conditions for processing chalcopyrite concentrate. The study found that finely ground chalcopyrite can be reduced carbothermically in the presence of lime at moderate temperatures and in a reasonable time to form metallic copper, with the sulphur reporting virtually entirely to calcium sulfide. At temperatures below about 750?770ºC calcium ferrite is the stable form of iron whereas at higher temperatures metallic iron is stable. Further work is required to demonstrate the reaction on a scale to obtain sufficient sample for evaluation of subsequent processing steps to remove the gangue material and iron products from the copper.

Jan 1, 2009

Commodities statistics and otter information are available through the following t et systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By Terry J. Close

At the request of the Idaho Congressional Delegation, the U.S. Bureau of Mines Western Field Operations Center investigated the mineral resources of the 140,000-acre Red Mountain roadless area, located northeast of Lowman, in central Idaho. The area includes U.S. Forest Service Red Mountain RARE II area (4-063). The highly mineralized road less area is underlain mainly by granitic rocks which are transected by a northeast-trending fault system. Associated with the granitic rocks and fault system are gold and black sand mineral resources. At least 1,395 ounces of gold and 858 ounces of silver have been recovered from six lode and placer mines within the roadless area. A total of 525 tons of columbium-tantalum, 2,049 tons of euxenite, 83.5 tons of columbite, and 54,862 tons of ilmenite concentrates have been produced from a nearby black sand mineral placer. Mine workings and facilities in the roadless area consist of two dismantled mills, 15 open and caved underground excavations totaling about 2,900 ft of workings, seven large pits and quarries, over 166 smaller dozer-and hand-dug prospect pits and trenches, and in excess of 66 drill holes. The mineralized sites in the roadless area are covered by about 690 current (1992) mining claims. About 130 individuals are holding the claims. Also within the roadless area are four patented lode mining claims. Twenty-five of the 54 mineralized sites identified during the study of the roadless area have, or likely have, mineral resources. One has gold and three have black sand mineral resources that are marginal or subeconomic. There also are two hot springs with thermal water resources, some veins that could be sources of decorative quartz, and dimension stone which was quarried in the past and could be again.

Jan 1, 1993

By M. Onifade, B. Genc, P. O. Akinseye, M. Fourie, K. O. Said

Coal is mined by both surface and underground methods and its extraction is normally characterized by numerous hazards that can lead to catastrophic accidents, which result in devastating effects such as injuries or fatalities, damage to mining assets, and destruction of mineral resources. These hazards exist due to the ability of coal to support combustion and its association with toxic, flammable, and explosive gases. Underground coal mining entails higher safety risks than opencast coal mining, chiefly because of issues relating to mine ventilation and mine collapse. Furthermore, coal mine collapses mostly occur due to crumbling of mining supports, especially in room and pillar mining systems. To avoid such adverse occurrences, safety management systems need to be in place. This study reviews the various technological safety systems and principles that are used for safe-rescue and self-escape of miners in underground coal fires, particularly in South Africa, using data obtained from Mines Rescue Services in Carltonville, South Africa. The outcome of the review shows that practising safety culture has been given priority across many South African underground coal mines through setting up safety management systems and encouraging workers to stay committed to safety principles.

May 2, 2022

By Chuck Edwards

"Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. Over that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin close out the paper.INTRODUCTIONThe roughly oval Athabasca Basin in northern Saskatchewan occupies nearly one third of the surface area of the Saskatchewan Shield. Its sandstone-like deposits lie unconformably on the older basement. The basin hosts many high-grade unconformity-type uranium deposits(Saskatchewan Energy and Resources, 2010) for which the Athabasca Basin is world famous. Uranium production in the Athabasca Basin has come from four mills. In the order of startup these are Rabbit Lake, Cluff Lake, Key Lake and McClean Lake. General data (AREVA, 2010; Cameco, 2010; Denison 2010) for each mill are shown in Table 1."

Jan 1, 2011

By John D. Foulkes

An investigation is made into whether commercially available equipment can be used to engineer effective emergency warning systems for underground coal mines. Discussions with members of the Bureau and the Mining Enforcement and Safety Administration established that the preferred system should operate over the existing Pager Phone twisted pair, and broadcast an audio alarm. Applicable equipments such as voice band tone signaling equipment, alarm sounding equipment, mine telephones and complete alarm systems from over thirty manufacturers are listed. Factors affecting the range over which an alarm could be detected in representative mine situations were studied. These included (a) the subjective masking effects of typical background noise found in mines, such as that due to continuous miners (b) the attenuation of sound in mines (using both a theoretical and experimental results) and (c) the attention-getting qualities of different sound for miners. Audio alarm systems meeting the requirements can be installed and representative systems are described.

Jan 1, 1977

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By A Hollweg, K H. Esbensen, M Lischka

Two new splitter designs for intercepting moving streams of matter are presented, the variable cross-stream splitter (vCSS) and the rotary stream splitter (RSS), which are intended for implementation in a fully automated modus. The vCSS facilitates obtaining up to three subsamples with different splitting ratios from automated laboratory flow paths, while the RSS divides the intercepted sample into 16 equal analytical aliquots. The splitters can process a wide range of dry, granular and free-flowing materials (<5 mm). The required weight for each subsample can be set without mechanical adjustments in the case of the vCSS. Typical applications are subsampling/splitting for X-ray fluorescence pelletisation (or fused beads) or splitting for average shift composite sampling or grain size analysis. The vCSS combines the advantages of riffle splitting (three user-defined subsample masses) with miniature bed blending and can accept up to 15 kg in total incoming sample mass. In practice, the automated vCSS can deal with unlimited ingoing mass fluxes, while the RSS is designed to operate at a user-defined fixed subsampling rate (1/16th in the tested version). Both splitters have the potential to be optimised and evaluated according to an application/user-defined total sampling error (TSE) + total analytical error (TAE) threshold. Both splitters were tested under adverse conditions and with compositions involving three components with properties representing typical mass fluxes and components concentrations in industrial and technological systems: phosphate concentrate 89.00 per cent (<500 µm), slag ten per cent (>2 mm) and glass spheres one per cent (750–1000 µm). The slag particles vary widely in particle shape, aspect ratio and surface roughness, while the glass spheres are extremely prone to bouncing and segregation (spillage). This test system is extremely difficult to split and thus constitutes a realistic worst-case scenario. While the vCSS does not comply strictly with Theory of Sampling demands for correctness, both splitters may well be able to deliver fit-for-purpose representative results if/when tested properly. Average relative mass deviations ranged from 1.89 per cent for phosphate concentrate (relative standard deviations of 20-fold repeated splitting) to 4.72 per cent for glass spheres and 13.04 per cent for slag. For the RSS, the average replication experiment splitting variation was 2.89 per cent for phosphate concentrate, 4.82 per cent for glass spheres and 11.1 per cent for slag. Both new automated online splitters would therefore appear to be able to be tuned to fit-for-purpose representivity (defined here as maximum relative reproducibility <5 per cent) for many non-extreme materials; however, it is always imperative to test every new type/class of material empirically. There is a wide commercial potential for important materials and commodities sectors, including food, feed, drugs (pharmaceutical), secondary raw materials, recyclates, agricultural products and seeds.CITATION:Lischka, M, Hollweg, A and Esbensen, K H, 2017. New online/atline splitter designs for laboratory automation – feasibility results, in Proceedings Eighth World Conference on Sampling and Blending , pp 159–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

In 2002 the authors updated the MFire model developed by the US Bureau of Mines. MineFire, developed by Mine Ventilation Services, Inc. (MVS), uses the MFire model to perform mine fire simulations on typical mine ventilation networks. The MineFire program is capable of producing visual schematics and other analysis tools for input and output of the MFire model. The MFire model, however, was limited to 500 branches and 10 fans. This paper discusses the newly modified MFire model that is now capable of modeling over 5000 branches and over 400 fans among other expansions and improvements. Given the long history and proven track record of MFire, the expansion did not modify the core calculation methods or results. This paper focuses on a general discussion of the MFire program and issues encountered in expansion of the algorithm. An example large network with simulation results is discussed.

Jan 1, 2011

By Sutham Niyomwas

Silicon-Silicon Carbide (Si-SiC) composites were synthesized by self-propagating high temperature synthesis (SHS) from a powder mixture of SiO2-C-Mg. The reaction was carried out in a SHS reactor under static argon gas at a pressure of 0.5 MPa. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of silica sources and carbon mole ratio in precursor mixture on the Si-SiC conversion were investigated using X-ray diffraction and scanning electron microscope technique. The as-synthesized products of Si-SiC-MgO powders were leached with 0.1M HCl acid solution to obtain the Si-SiC composite powders.

Jan 1, 2009

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation has been investigated as a process to convert gaseous CO2 into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results have been achieved using heat pretreated serpentine feed material and high partial pressure of CO2 (PCO2). Specific conditions include: 155°C; P002=185 atm; 15% solids. Under these conditions, 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy has been utilized to investigate the appropriate feed characteristics, identify the process products, and interpret the mineral dissolution and carbonate precipitation reaction paths.

Jan 1, 2001

By VIVEK KASHYAP, PATRICK TAYLOR

The presence of iron in sphalerite induces the formation of zinc ferrite (ZF) during roasting. Zinc refinery residues (ZRR) and electric arc furnace dust (EAFD) contain a significant amount of zinc ferrite and are difficult to treat. According to the literature, up to 71% ZF has been found to be present in ZRR. The dissolution of zinc ferrite is inefficient even in aqua regia. The Waelz process is an existing process to recover zinc from electric arc furnace dust by reduction using carbon monoxide followed by the volatilization of zinc. In this study, zinc was selectively extracted from zinc ferrite by partial reduction of zinc ferrite at relatively low temperature followed by leaching in dilute sulfuric acid (20 g/L). Pure zinc ferrite samples were partially reduced to zinc oxide and magnetite by using H2 gas as a reductant. The presence of magnetite and zinc oxide was confirmed by X-ray diffraction (XRD) technique. A maximum of 95%zinc extraction was achieved after leaching with sulfuric acid on the reacted samples. The paper also discusses the effect of time, temperature, and concentration of H2 in the reducing gas on the extraction of zinc and iron from ZF.

Sep 16, 2020

By Gabsoo Kim, Rulin Yang, Dave Kay

Blast vibration data, such as PPV are usually scattered. In many cases, plots of PPV versus the charge weight scaled distance are so scattered that useful trends from different blast designs cannot be identified. The scattering of the data may be attributed to the inaccuracy of the PPV measurement, the definition of the scaled distance from a multiple-hole production blast, and the measurement of distances and charge weights. The error from vibration measurements is one of the major contributors to the scattering of the plots. If accurate monitoring is conducted, improved design options may be identified. This paper documents two case examples that compare different vibration sensor couplings. The first case shows mounting accelerometers at spots that protrude from the ground, compared with the sensors that were mounted on a flat ground surface. The second case compares data from loose-sand buried geophone with that from sensors coupled to the ground using concrete blocks.

Jan 1, 2014

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009