Search Documents

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

By Q. Liu, S. Liu, Y. Cui

To reduce the frequency of mining incidents and improve safety and production efficiency, it is important to develop technology for the autonomous positioning and navigation of mining equipment, without the assistance of satellite navigation signals. In this study we review the current technological environment for positioning and navigation underground and present several integrated navigation strategies. Existing underground positioning and navigation technology is described, and the performances of different methods based on this technology analysed and compared. The combination types and positioning effects of underground positioning and navigation strategies are discussed. Recent research directions for filtering methods and positioning estimation algorithms for underground positioning and navigation are reviewed. Finally, we summarize the future direction of underground positioning and navigation technology and related algorithms.

Jun 1, 2021

By Raymond W. Henn, Kent A. Pease, Glen J. Rorison

The paper focuses on construction of a 2.55-km (8,365-ft) long, 2.4-m (8-ft)diameter storm drain tunnel in Evansville, Indiana. The tunnel was driven through saturated soft ground varying from clay to fine sand. The paper presents: an overview of design and design rational including specific EPB machine requirements; the contractor’s proposed and accepted alternative construction methods and TBM design; and construction issues and performance. Some of the key points discussed are the use of the TBM in different operational modes for alternative ground conditions, the effectiveness of dewatering systems, production rates, and issues such as surface settlements and gas.

Jan 1, 2001

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By Gabriel K. Nzulu, Lars Hultman, Per Eklund, Martin Magnuson, Abu Yaya, Prosper M. Nude, Hans Högberg

Pyrite is the most common among the group of sulfide minerals in the Earth and abundant in most geological settings. This gangue mineral in association with garnet, hematite, magnetite, and other sulfide minerals acts as an indicator mineral in the Kubi concession of the Asante Gold corporation in Ghana. X-ray diffraction (XRD), air annealing in a furnace, energydispersive x-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS) were applied to investigate the crystal structure, identify individual elements, permanence, transformation, and chemical/electronic properties of such pyrite. The study aims to identify individual elements and to gain an understanding of the surface reaction mechanisms, as well as the properties of precipitated pyrite particles observed during the hydrothermal formation of the ore deposit. XRD shows that pristine and annealed samples contain some hematite and quartz besides pyrite. Results from air annealing indicate that the relationship between pyrite and hematite-magnetite is controlled by temperature. EDX reveals that the sample has O and C as contaminants, while XPS in addition reveals Ba, Au, P, Al, and N. These elements are attributed to pyrite that bonds metallically or covalently to neighboring ligands/impurity minerals such as oxides, chalcogenide sulfides, as well as the gangue alteration minerals of magnetite and hematite in the pyrite sample. These findings suggest that during the hydrothermal flow regime, pyrite, pathfinder elements, and impurity minerals/metals were in contact with quartz minerals before undergoing hematite transformation, which thus becomes an indicator mineral in the Kubi gold concession.

Feb 27, 2024

By D. R. Jolley

"The selection of equipment for open-pit mining is an important decision which results in a considerable capital expenditure by the operator. The decision is complicated by the wide product range on the market. Certainly, equipment performance is an important criterion to consider in making the decision. Equally important, however, is the operating inter-relationship among the equipment. A poor balance increases production costs and waiting time as queues form at the bottlenecks. This inter-relationship is dependent on equipment performance, but it is also affected by management decisions (i.e. scheduling techniques).The purpose of this paper is to show how the computer is used to decide which equipment and operating decisions achieve the required production objectives at least cost. Actual mining of the pit is simulated over a period of time using different equipment and scheduling decisions. Production, waiting time and costs are evaluated for each alternative until the operator is satisfied that he has achieved the best result."

Jan 1, 1970

By J. A. Cooper

The objectives of this research were to define the chemical composition and physical characteristics of the aerosols associated with attached radon daughters in operating uranium mines, and to investigate the relationship between these aerosol parameters and operating conditions. Major Results and Conclusions The organic, inorganic and radiological characteristics of test chamber and active U-mine aerosols have been measured as a function of particle size. These measurements represent the first detailed analyses of the organic and inorganic components in U-mine aerosols and the first determinations of the details of the individual and total radon daughter distributions in operating U-mines. The following is a list of the major results and conclusions:

Jan 1, 2012

By Julie Culverhouse, Dennis Grimm, Kieran Harding, Jean-Francois Boulanger

"Agrium’s Canadian Phosphate Business (CPB) is comprised of Kapuskasing Phosphate Operations (KPO) in Northern Ontario, Canada’s only operating phosphate mine, and Redwater Phosphate Operations (RPO) in Alberta, which manufactures the fertilizer from KPO’s concentrate.Production from KPO’s South Pit commenced in 2009 and introduced contaminant problems: high aluminium from crandallite and kaolinite clays. These issues caused a drastic decrease in P2O5 recovery and throughput in both plants. KPO attempted to reduce Al clays by means of aggressive desliming. Meanwhile RPO experienced high amounts of dissolved metals in their feed that are detrimental to fertilizer production.This paper covers the mineralogy of the problem, its impact on contaminant separation at KPO, on RPO’s process and on Agrium’s Canadian Phosphate Business as a whole.Potential solutions to the problem are discussed and analysed, including a process change to deslime high aluminium streams more aggressively and high grade ore flotation, which is atypical at KPO. The latter is a demonstration of the value of communication between the concentrator and the client, as KPO accepted a recovery loss and increased production costs in order to increase overall CPB profits. General lessons learned are discussed, followed by a section on ore blending.INTRODUCTIONAlthough the existence of the Kapuskasing phosphate deposit has been known since the 1970s, it’s only since 1999 that Agrium has been operating the Kapuskasing Phosphate Operations (KPO). The mine consists of three major pits (Center, North and South) from which a mining contractor hauls the apatite ore to the Agrium concentrator. The beneficiation plant processes the ore, separating contaminants such as Fe, Mg and Al which are detrimental to its client, Agrium’s Redwater Phosphate Operations (RPO). The KPO concentrate is finally thickened, filtered and dried before being shipped by rail to RPO.At the Redwater plant, the KPO concentrate is added to a sulfuric acid solution in an attack tank, to create a phosphoric acid solution and gypsum:"

Jan 1, 2011

Appropriate roof control is the most important requirement in underground coal mining and, in the case of longwall panels or second mining in room and pillar extractions, this can be simply expressed in terms of good and predictable roof caveability. Studies of roof caveability have been undertaken in many coalfields around the world. Most of their conclusions. however, are directly related to the mining and geological conditions experienced in these areas and as a result, may not be applicable to the conditions encountered in the Appalachian coalfield. Furthermore, some of these studies appear to be theoretical and conceptual, ignoring many important parameters of the geological environment, whereas others rely heavily on geological information but lack a rigorous foundations upon which quantitative design guidelines can be built. The objective of this study is to analyze caving and mass deformation characteristics above longwall panels in Appalachia and includes: - Analysis of the effects of the geological and geomechanical characteristics of the strata on the caving height and the bulking of the caved-material. - Testing of the applicability of the various theoretical and empirical models of roof caving. Formulation of a numerical around- deformation model for ion-elastic material behavior.

Jan 1, 1986

By D. G. Tisdale

A pilot plant was installed and operated at the Xstrata Nickel Sudbury Smelter 10 demonstrate the CANSOLV SO2 Scrubbing System. A 350 m3/h slipstream (through a 10cm pipe) was drawn from two different industrial gas streams to test the performance and robustness of the scrubbing system. The system achieved high sulphur capture, typically above 99%, and proved tolerant 10 varying gas strength and dust content in the feed gas.

Jan 1, 2009

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

By M. W. Airth

ON THE 6TH JULY in the year 1953 an announcement was made to the public that touched off one of the greatest staking rushes in the history of mining in Canada and resulted, in tl1e space of a few short years, in the development of the greatest reserves of uranium-bearing ore in the world. It was ?On this date that the famous "Blind River back-door staking bee" was completed with the acquisition of some 2,000 claims by the Preston East Do me-Technical Mine Consultant teams under the direction of Mr. Franc Joubin and Mr. Robert C. Hart. That story has been told from coast to Coast and is too well known now to re-quire elaboration. Suffice to say that, in the short elapsed time of less tl1an five years from that momentous summer of 1953, three of the Algoma mines are in full production, three more are rapidly nearing full production, five more 1are approaching the production stage, a new hard-surfaced highway, 108, has been built to serve the area, and a brand new, completely planned city, Elliot Lake, is being built to provide the amenities of living to the 22,000 people already in the area.

Jan 1, 1958

By A Vickerfält, J Huss, J Martinsson

The European Union has listed vanadium (V) as one of the critical raw materials for the transition to a future green society, as stated in the Critical Raw Material Act, written by Grohol and Veeh (2023). In the steelmaking industry based on V-containing iron ore, V is a possible by-product from the slag. A requirement for slags to be suitable for V extraction is a V content preferably above 8 wt per cent as V2O3 and a phosphorus (P) content below 0.1 wt per cent as P2O5. Hence, it is important to keep V in the slag phase while the P is moved to the metal phase during the steelmaking process.

Aug 21, 2024

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units."

Jan 1, 2012

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By W. Rostoker, R. P. Elliott

TWO intermediate phases enter into equilibrium with the primary solid solutions of titanium.' The TiMn2 phase was identified by Wallbaum2 as of the C14 type isomorphous with MgZn2. Contrary to Maykuth, et al.,¹ the phase occuring at about the 50-50 atomic proportion has been shown to derive from a peritectoid reaction.:' A 30 day anneal at 900°C of an alloy containing 52 wt pct Mn developed sufficient of the new phase to give a clear and predominant diffraction pattern. The powder pattern was taken in a 14 cm diameter powder camera using filtered Cu Ka radiation. In all, 75 lines were recognized and measured. Interplanar spacing and observed intensities for the first 26 of these are given in Table I.

Jan 1, 1954

By Walter E. Heinrichs

The following is a condensed version of an open letter addressed to Bil Gilbert of Sports Illustrated: Your article, "When a Law Fights a Law, Sports Illustrated. April 26, 1971, betrays considerable unfamiliarity with the subjects of ecology, social science, mining law and history. In a magazine as widely circulated as Sports Illustrated, an article of such a slanted nature misleads the general public.

Jan 1, 1971

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division Established as a Society February 26, 1957 OFFICERS AND COMMITTEES J W Woomer, President A B Cummins, President-elect S D Michaelson, Past President C E Lawall, Eastern Regional Vice-President D W Scott, Central Regional Vice-President 3 D Forrester, Western Regional Vice-President R B Ladoo, Treasurer John Cameron Fox, Secretary

Jan 1, 1959

By J. Temporal

An introduction to the conference material in this issue is given together with the issue contents list, closing remarks by its chairman Dr. J. Temporal, the list of contributors and their companies, and the information that the 26th Sir Julius Wernher memorial lecture had had to be presented by the lecturer's wife, M. Biggart, in his absence due to site problems on the Storebaelt project

Jun 16, 1905

By Tom Treleaven, Andrew Williams

The town of Greenwich, CT, an exclusive suburb of New York City awarded several contracts for the installation of sanitary sewer in the North Mianus section of town. The Valley Road section was the most challenging from a rock excavation standpoint. The cut was up to 14 ft (4.25m), with adjacent utilities [20 in. (500mm) water, 6 in. (150mm) water and 8 in. (200mm) gas] located to within 5 ft. (1.5m) of the proposed sewer trench. Rock types varied but were ultra metamorphic in nature, ranging from quartzites, granite gneiss and various types of migmatities.

Jan 1, 2004