Search Documents

By Harry Siewert

"The commissioning of the 4th concentrator (C4) at Freeport Indonesia in early 1998 increased total mill throughput from 130k to 230k tonnes per day. The C4 flowsheet consists of a single 38 ft diameter SAG mill, four 24 ft diameter ball mills followed by four banks of 4,500 ft3 WEMCO flotation cells.The design of the C4 rougher flotation circuit was based on the expectation that the copper and gold recoveries achieved with the 4500 ft3 flotation cells would be equivalent to or better than that achieved with the 3,000 ft3 flotation cells in the 3rd concentrator (C3) rougher circuit. This assumption was due to the fact that the C4 flotation feed size would be less than 15% +212 microns compared to the C3 rougher flotation feed size of less than 23% +212 microns. By mid 1998 it had become apparent that the C4 rougher flotation copper and gold recoveries were below those predicted.In order to determine the cause of the lower recoveries, stage by stage rougher flotation surveys were performed in all four concentrators. The results of the surveys showed that the C4 rougher flotation circuit had a lower recovery of +200 micron material than that achieved in the C 1, C2 and C3 concentrators. Through mineralogical analysis, it was determined that a majority of the copper contained in the +200 micron fractions was liberated and recoverable. This paper describes the steps taken to increase coarse particle recovery, overall plant recovery and the results achieved."

Jan 1, 2001

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By AIME AIME

N EARLY 1300 members and guests crowded the halls of the Engineering Societies Building during the winter meeting of the Institute just closed, and more than 600 attended the banquet. In variety of program, quality of papers, interest in discussion, and brilliance of social features, the meeting maintained the high reputation of the past. Nothing elaborate in the way of excursions was attempted, experience having proved that February weather in New York is much too uncertain to warrant extensive field trips. A sight-seeing journey up the Hudson to the Bear Mountain bridge was, however, made despite the snows of the week before and the week after. The annual business meeting, while attended by a minority of the members in the building, was marked by the display of keen interest in the work and called out several interesting discussions. The excellent reports of the committees that had organized their work and directed it along definite lines, emphasized the need of funds with which to support assistants or Fellows who shall correlate and put to the highest use the facilities of the Institute in research along technical lines. This thought was developed at the banquet by the retiring president, J. V. W. Reynders, and it is expected that the Directors will take early steps to collect a fund for this purpose. The number of the individual sessions was too great and the papers and discussions too numerous to permit mention here of all the features of inter- est. A general review only follows. The papers and detailed discussions will be printed and sent to members as promptly as possible.

Jan 1, 1926

By Thomas Curtin

The Bureau of Mines, in its researches aimed to prevent wastes and to increase efficiency in oil-well practice, has investigated the matter of casing troubles and fishing methods. The results of the investigation are set forth in this paper. After expensive development work, many wells being drilled for oil have been abandoned because of casing troubles. These troubles in many instances have been thought to be insurmountable, whereas they are sometimes susceptible of solution. In fields_ where casing difficulties are of daily occurrence, methods have been evolved for combating them. Were these methods more widely known and applied wherever the same conditions exist, the oil industry at large would be greatly benefited. This report attempts to classify these troubles and suggests solutions that will save the operator discouragement and expense. It is assumed throughout this paper that the reader is so familiar with the ordinary oil-well drilling and fishing methods that detailed explanation is unnecessary. The well-drilling terms that are used herein will be readily understood by those for whom this discussion is intended. However, in order to avoid confusion as to the sense in which some of these terms are applied, definitions &re included.

Jan 1, 1920

By J. Daavittila, P. Jokinen, M. Honkaniemi

In the latter part of the 1980?s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation an application for FeMn production was developed. Now when Tornio FeCr-plant is considering the expansion the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand of better working conditions. The possibilities to respond to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control of the process even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The U.S. National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two-phase implementation of an IoT-based intelligent machine monitoring system.

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining Co.'s Granite Mountain shaft. How this insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the lire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest pro¬ducer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

In choosing such a threadbare subject for a paper I fear that I may in some measure be taxing your patience, yet as upon the accuracy with which the work is done depends the result of conclusions drawn as to whether a property will be profitable to work or otherwise. The subject cannot be too well threshed out, and I trust that upon certain points that have come within my own experience I may be able to give 'hints that will prevent others from making mistakes. First as to alluvial. Gold is often found from the grass roots down, often ill particular horizontal bands in the wash, but more generally concentrated either on a true or false bottom. When sampling dry ground for proposed hydraulicing I have obtained accurate results only by taking the whole of the dirt from measured shafts, stacking it as it was lifted on a tarpaulin, and putting the whole quantity through a carefully constructed box. In wet ground careful borings will in most cases give fairly correct results, but where it is possible to sink shafts, that should be done, as a guide is then also obtained as to the nature of the wash, whether it is bouldery, cemented, or free. Sampling in a face is a more difficult work in many respects than in new ground, as so many elements enter into action to spoil accurate sampling. Of course the great thing to avoid is sampling in any place where either natural or artificial concentration has taken place, and very much has to be left to circumstance and the sampler's own judgment. In passing I may mention that I have on several occasions seen diggers deceive themselves in wet ground where they were sinking and coping as best they might with water. They would take a dish of dirt from the bottom of their hole, pan it off, and take the result as a fair yield, and on the strength of it perhaps spend a lot of time and money in tail races and whereas in their sample there had been a process of concentration carried on, the movement and working in the water had caused the gold to work down, and anything like accurate estimations by the method pursued were out of the question.

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Chen, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates are widely used in smelting operations worldwide and typically consist of chalcopyrite ( CuFeS2) as the primary mineral, with chalcocite ( Cu2S) and bornite ( Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates often contain hazardous impurities, such as the fluorine ion, which can result in various complications during the smelting process. These issues include equipment corrosion, gas treatment requirements, environmental hazards, and strained community relations. Furthermore, high fluorine content in copper concentrates can lead to penalties and limitations during sales. To address these challenges, this comprehensive review assesses current techniques for removing fluorine from copper concentrate. Drawing upon recent research and the findings in the field, the review analyzes the advantages and disadvantages of existing fluorine removal methods and identifies critical issues requiring attention in the future. This review provides valuable insights into the current state of fluorine removal from copper concentrates and serves as a practical guide for researchers and industry professionals in this field.

Aug 2, 2023

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By BUREAU OF MINES

This report is submitted in accordance with the provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1953 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5043, Part I - 011 From Coal. R. I. 5044, Part II 011 From 011 Shale. - Identical in each report, the introduction summarizes research progress made in 1953 under the entire Synthetic Liquid Fuels program. A free copy of each of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Apr 1, 1954

By Joseph A. DeCarlo

The rapid growth of the organic chemical industry in the United States and abroad has focused attention on the future raw-material sources for this important industry. Chemical products are essential to modern civilization; and millions of tons of organic chemicals are used annually, ranging from basic raw materials to finished chemical products such as drugs, cosmetics, and soaps. Hundreds of chemical products are made directly or indirectly from coal, but in this report "coal chemicals" will be limited to crude tar, crud light oil, and ammonia recovered in the high-temperature carbonization of bituminous coal and the important principal products obtained by processing these materials. Specifically these include benzene} toluene, xylene, naphthalene, creosote oil, tar acid oil, pitch, and ammonium sulfate. Therefore the term "coal chemicals", wherever used in this report, includes only these products and does not include the secondary or intermediate products such as styrene, synthetic phenol, aniline, phthalic anhydride, or finished products made from these, such as synthetic rubber, plastics, and dyes. The United States leads the world in production and consumption of coal chemicals. In the past five years nearly one-fourth of the total output of coal-tar crudes in the world was produced in the United States. Consumption of some of the more important products derived from these crudes such as benzene, toluene, xylene, and naphthalene, however, ranged from about one-third to one-half of the world total because of imports and production of benzene, toluene, and xylene from petroleum. The synthetic organic chemical industry of the United States was established during World War I on chemical raw materials obtained by the high-temperature carbonization of bituminous coal but this source of supply currently furnishes less than 40 percent. More than 60 percent of the chemical raw materials used to produce organic and inorganic chemical is supplied by the petroleum industry and production of petrochemicals is rising rapidly.

Jan 1, 1960

By Thomas C. Shapiro

This is the final article in a three-part series on microcomputers and application software in the mineral industry. The first article covered microcomputer terms and concepts. The second discussed exploration and mining software. This article will examine plant, administrative, and geotechnical software. Every effort has been made to be current in the latest software developments. Rapid change, however, is a fact of life in the computer world and any omission is inadvertent. Introduction Geotechnical disciplines have received considerable attention in software programming. Calculations are repetitive and the formulas needed to solve them are not extremely complicated. These programs are ideally suited to the microcomputer and the microcomputer is ideally suited to the consulting geologist or engineer, due to its low cost and reliability. In fact, the advent of the Apple (a registered trademark of Apple Computer Inc.) and, more recently, the IBM personal computer has caused an explosion of inexpensive software programs available to the microcomputing public. Another area that has benefited from computerization, although not in the same way, has been mineral beneficiation. Here, process control for start-up or phase-down operations has been used in newer plants for some time. Programs to perform various calculations are becoming more common as micros increase in number. Tappi Journal has a section with solutions to handheld-calculator and microcomputer problems. Process Modeling Most process modeling is still done only on mainframes. One such program is called ASPEN PLUS (a registered trademark of Aspen Technology), and a one-week course is recommended so the user can best use the program. This program is available through timesharing from University Computing Co. Programs to find an optimal solution using Linear Programming (LP) have been around for some time. Also, plant process simulation has been possible using simulation programs. Both simulation and LP are expensive to program and run. Although there are LP programs available for some micros, the user must be fairly knowledgeable about how to set up the problem. This is because each problem must be set up as a unique program that typically requires custom programming. There are some programs that can handle blending of mine crudes and examine economic parameters over the life of the mine. Plant Applications Areas relating to mine and plant applications with programs available for micros are maintenance, production reporting, inventory, accounting, and personnel scheduling. Maintenance Maintenance typically requires that certain jobs be performed in a particular sequence and parts be ordered with enough lead time for maintenance to take place on time. There is, therefore, a critical sequence of tasks that must be performed or the scheduled maintenance will not take place. Two answers needed for maintenance project scheduling are: what is the lead time needed

Jan 4, 1984

The Ocean Drilling Program (ODP) is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (legs) which each last approximately two months. These legs are designed by geoscientists from the nineteen countries that subscribe to ODP.Australia and Canada presently share ODP membership under the banner of the AUSCAN Consortium. The benefits of Australia's involvement in ODP include internationalisation of Australian geoscience, advanced graduate training, and unique scientific investigations of the ocean floors in the Australasian region. In addition, visits to Australian ports by the ODP drill ship, the JOIDES Resolution, contribute up to $2 million per visit to the local economy. Amongst the many other aspects of ten years of scientific drilling, OOP has significantly contributed to our understanding of hydrothermal processes on the seafloor. To date, three hydrothermal sites have been drilled to date by the OOP, Snakepit (MAR), Middle Valley (Juan de Fuca Ridge) and TAG (MAR). Two more hydrothermal sites are scheduled for 1996.

Jan 1, 1995

By R. S. Dean

T HE theory of hardening by heat treatment was, as usual, the most actively discussed phase of metal working theory and in spite of the fact that it is now ten years since the dispersion theory was proposed by Messrs. Merica, Waltenberg, and Scott, it still retains a dominating influence. It is being increasingly recognized. however, that in its simplest form, that is, the purely mechanical effect of very fine crystallites distributed through a groundmass, it is distinctly in- adequate. To explain the observed facts we are obliged to assume some well-defined intermediate stage between supercooled solid solution and conglomerate, however fine be the particles of the latter. This intermediate has been inferred by Gaylor and Preston to be "the rejection of the atoms of the dissolved metal from the lattice of the solid solution accompanied by the possible formation of molecules."' Perhaps this may well be designated as the formation of supersaturated solid solution. Some very definite evidence of such an inter- mediate stage has been found in the hardening of steel where it appears that the very hard martensite may be considered as a supersaturated solution of carbon in a iron. The X-ray spectrometry of drastically quenched steel shows a tetragonal lattice whose parameter changes by tempering at 100" until it coincides with the cubic lattice of iron.? The same gradual change of the tetragonal to the cubic lattice has been observed by Sekito when esamining layers on increasing depth below the surface of a quenched carbon steel.

Jan 1, 1930

By K. L. Paciorek

The primary objective of this final phase of Contract No. H0133004 was to provide a description of all experimental assemblies and procedures used throughout this project in such a detail as to permit duplication of the tests in any other laboratory. A further objective was to summarize and evaluate all results generated throughout the duration of this program and to tabulate all the materials and data in such a manner as to allow this report to be used as a reference index for specific compositions or groups of compositions regarding potential hazards arising from their use .in underground coal mining operations. The report also contains an updated survey of the literature on thermal oxidative degradation of compositions investigated under this contract.

Jan 1, 1978

By G. Miller

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixers. Recent experience with both large and small plants has shown that this is not the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers. Both of these lead to either reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Further, changes to the method of specification and selection of both primary and secondary mixers have been made to eliminate the onset of partial separation during operation. Observation of settler operation has shown that it is also a dynamic process, even under ‘steady state’ conditions. Four different transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze, and erratic and high entrainment levels in the discharges. A first approximation analysis has shown that there are significant pressure differentials within settlers and these change along the length and with phase separation rates. A technique to control the effects of these transients has been developed which allows plant performance to be improved beyond ‘standard’ expectations. The design and selection of the settler internals is described.

Jan 1, 2001

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, Mari Lundström, Eero Kolehmainen

With decreasing ore grades, the tailings of mining operations are becoming of increasing interest as metal-containing secondary raw materials. The objective of the current work was to investigate chloride leaching of gold, copper, cobalt, nickel, and zinc present in the flotation tailings. In the current study, the effect of cupric ion as an oxidant (0–50 g/L) and NaCl (150–250 g/L) on metals extraction was investigated. The other parameters, such as pH (1.8), temperature (95 °C), solid/liquid ratio (25%), oxygen feed rate (1200 mL/min), leaching time (24 h), and stirring rate (950 rpm), were kept constant. Gold dissolution rate was shown to increase with increase in cupric ion concentrations up to 50 g/L. Also, increase in NaCl concentration up to 250 g/L increased gold extraction. Majority of the copper present in the flotation tailings could be dissolved with all the all solutions investigated. The other base metals, cobalt, nickel, and zinc extractions were also shown to increase with increase in the cupric ion and sodium chloride concentration. However, even in the absence of cupric ion addition (t = 72 h, 250 g/L NaCl), the final extraction of Cu, Ni, Zn, Co, and Fe increased up to 98, 93, 83, 76, and 80%, respectively. This shows the power of inherently originating oxidants present in the tailings. Furthermore, the solid analysis of the leach residue indicated that leaching the flotation tailings in pure NaCl may result in partial gold dissolution. The results demonstrate that significant amount of metals present in the tailings could be extracted even with only NaCl as added chemical in the presence of oxygen feed, oxidizing agents originating directly from the raw material. This can provide an advantageous cyanide-free method for extraction of metals from very low-grade tailings with low chemical consumption.

By M. Bilal Khan

Thermal stress relief by means of a typical heat treatment cycle (660oC for one hr) is compared with the one achieved through vibratory stress relief at resonant and multiple resonant frequencies for the D-406 HSLA material. Our analysis of the data is based on the microhardness profiles measured for the entire length of scales, namely, base metal, heat affected zone (HAZ) and the weld bead itself. The profiles obtained using the two techniques mimic each other, for an equivalent 70% stress relief level. The data are further qualified by impact testing wherein the zone of interest is projected in the retention groove to provide impact by the pendulum striker in the Charpy mode. Higher equivalent energy absorption in the treated specimens confirms the efficacy of the vibratory method. The present work rectifies earlier anomaly where heat treatment has been reported at 310oC for the same material.

Jan 1, 2009

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country's steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999