Search Documents

By I. A. Mwamba

Plain and alloyed titanium aluminides of composition Ti-47.5 at.% Al were prepared by melting commercial-purity titanium and aluminium with additions of 1 at.% precious metal. The as-cast alloys were subjected to potentiodynamic scans in 5, 15, and 25 wt% HCl aqueous solutions at room temperature and compared for their abilities to spontaneously passivate. Addition of precious metals resulted in a general improvement of corrosion resistance by increasing the open circuit potential to more noble values. Addition of 1 at.% gold or silver to titanium aluminide did not significantly increase the corrosion potential (Ecorr) above that of the plain titanium aluminide alloy, indicating that gold and silver are not sufficient cathodic modifiers to improve the corrosion resistance of titanium aluminide in all the solutions tested. However, platinum, palladium, and iridium additions shifted the corrosion potentials to the position of the passive region of plain TiAl for all solution concentrations. This indicated that TiAl alloyed with these platinum group metals would passivate spontaneously by cathodic modification. TiAl alloyed with palladium performed the best in 5 wt% HCl solution with the most positive corrosion potential. In 15 wt% HCl solution, alloys with platinum exhibited the most positive corrosion potentials, while alloying with iridium or palladium revealed more negative corrosion potentials. Thus, palladium alloying led to the best cathodic modification of titanium aluminide in low-concentration HCl solution, whereas platinum and iridium alloying additions resulted in the best cathodic modification of titanium aluminide in high-concentration HCl solutions.

Jan 1, 2013

By Pervez Patel, Martin G. Frohberg, Demetrios Papamantellos

Model experiments were carried out on the mass transfer of iodine between n-hexane and a 4 2 X 10-3 M aqueous sodium hydroxide solution. The influence of mechanical stirring by means of small gas bubbles (ca. 0.01 ml in volume) on mass transfer was examined in independent experiments. The results were described with the help of the penetration theory and in the case of bubble stirring with the help of a mathematical model based on this theory. S LAG-METAL reactions, especially those in steel-making processes, often occur under conditions where gas is evolved in the form of bubbles that break through the slag-metal interface. It is known that stirring by means of bubbles increases the mass transfer coefficient, but there has been very little quantitative work done in this field. Because of the difficulties that attach to experimental work at high temperatures this study was confined to model experiments at room temperature. EXPERIMENTAL APPARATUS The transport of iodine from an n-hexane layer into a weak sodium hydroxide solution was studied a) with stirring by means of bubbles and b) with mechanical stirring. The apparatus for the experiments with bubbles consisted of the cell, two Dreschel bottles filled with hexane in order to saturate the nitrogen flow, one flow meter, and a nitrogen gas cylinder fitted with a fine-regulating valve. Fig. 1 shows the cell consisting of a glass cylinder 33 cm in height with an overall diameter of 7.5 cm embedded in a copper flange. The flange is connected to a Plexiglas plate and to the gas inlet. The Plexiglas plate has holes of 0.2 mm diam bored into it which are spaced 1 cm from each other. For the experiments with mechanical stirring the bottom of the cell was sealed off by a Plexiglas plate. The upper layer was stirred by means of a glass stir-rer and the bottom layer with the help of a magnetic stirrer in a counter rotatory direction. Both stirrer speeds could be varied continuously. EXPERIMENTAL PROCEDURE Iodine dissolves in n-hexane producing a stable violet color thus enabling the iodine concentration in

Jan 1, 1970

By M. Hochenhofer

Keywords: desulfurization, mathematical model, slag reaction To produce ferroalloys like ferro-nickel for alloying purposes in a quality that meets the requirements of today?s steel industry, refining processes like desulfurization and dephosphorization are indispensable. The performance of desulfurization-treatment by slag reaction depends on various parameters, such as: sulfide capacity and viscosity of the slag, sulfur distribution between metal and slag, activity of sulfur in melt and movement of melt. Within this work, the combined influences of these parameters on the desulfurization of a ferro-nickel alloy were examined. As a basis for this examination, a mathematical model, based on data from plant trials, was created. This model demonstrates the relationship between desulfurization rate and initial values of the above mentioned parameters. With this model the relevant parameters were evaluated and assessed concerning their influence on desulfurization.

Jan 1, 2005

By John Ralston, Jonas Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By G J. I dos Santos

The risk assessment of mining projects is directly related to the possible failure in estimating, and as estimates are made from sampling results, this activity should be done in a judicious and planned manner, to avoid surprises at the start of project operation. Pierre Gy’s (1995) sampling theory addresses the issue of sample representativeness and indicates that only the certainty that the sampling procedure was performed with quality may result in samples being recognised as representative. To validate the representativeness of samples from sampling boreholes selected for studies of mineral processing, the team of geology resource assessment of VALE has proposed a methodology based on the use of statistical analysis tools, which in addition to considering the spatial distribution of these samples in deposit, considers whether they are representative of the populations studied, allowing the geologist to make a quick analysis of sample representativeness.

Jul 11, 2011

By Yongfu Yu, Xiaotie Wang, Fuguang Zhang, Liping Che

"Rare Earth water dregs is the drained waste dregs, which contains over 0.2 percent thorium dioxide and about 6-10 percent di-Rare Earth trioxide, which is beyond the standard of draining off that China governments set, so that the Rare Earth water leach dregs must be sacked and laid down in storehouse, which costs lots of money. It is a pity that the RE and thorium compounds very useful elements in industry are discarded. A lot of work must be carried out so that this resource was fully developed.In this paper, four separation techniques of recovery Rare Earth minerals and enrichment thorium element and reduction thorium content of drained dreg for the different test samples of Rare Earth water leach dregs which is radioactive waste dregs got from diverse locus are studied, respectively, and the separation characteristic and the separation process are described, using several combination processes of classification and gravity and flotation separation which were prepared according to the characteristic of test samples and technology. The test results show that the combination processes are the more remarkable separation techniques and the flotation reagents used in test can be applied to utilizing synthetically radioactive waste dregs. Through the combined technique process, three parts of products were obtained, namely, Rare Earth concentrate collected, the thorium product enriched and a large amount of the waste dregs product that can be directly drained and the total quantity is 50%-60%. In order to determine optimum technical condition, the effect factors of separation process were investigated in the test."

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Mineral froth flotation is one of the most widely used processes to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. The hydrophobic particles attach to the air bubbles and rise up to the froth phase on top of the slurry. The valuable mineral is collected when the froth overflows the cell wall. The separation performance of the process can be linked to the amount of solids and valuable material loaded on the bubble shells. In addition, it is well known that in most mineral systems, the presence of solids can enhance the stability of the froths. How the solids get to be distributed and what proportion is actually attached and stabilising the bubbles is not well known.This study aims to establish the relationship between operational variables, solids loading on bubbles and flotation performance. For this purpose, a series of industrial experiments to sample the solids in the bubble films under different operational conditions were carried out in two copper concentrators under steady state conditions. Samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. The amount of solids and liquid per unit area in the bubble lamellae can subsequently be estimated gravimetrically and by image analysis. The grade of the attached particles was also measured by adequate sampling. This gives an indication of the maximum grade that could be achieved from the process under the operating conditions."

Jan 1, 2003

ON mineral lease 38 of the Sulphide Corporation Limited, Broken Hill, a shaft was sunk in the early days Ior prospecting purposes and at the present time it is accessible as far as the 1000-ft. level where a connexion exists with the main workings of the Corporation's Central Mine, mineral lease 9. About the year 1895· a crosscut was driven east from this shaft at the 1330-ft. level cutting the Central Ore-body in mineral lease 9 and the shaft is supposed to extend a further depth of 25 ft; but no records of any of this work are in existence, the whole of the evidence being based on hearsay and memory:Fig. 1 shows the position of the Extended shaft in relation to the main workings. The shaft filled with water to the 1000-ft. level where it overflowed through the crosscut to the main shaft and was pumped to the surface, but when the South drive on the 1300-ft. level was pushed to the southern boundary, it was deemed advisable for safety, to tap the water at this level and so relieve the...

Jan 1, 1919

By M. Sturzenegger

This paper documents a field survey using long-range terrestrial digital photogrammetry at the Palabora open-pit mine, South Africa, for multi-scale characterization of rock mass discontinuities. Stereomodels covering the entire mine were generated based on photographs taken from a distance of 1600m across the pit, using a series of f=20-400mm lenses. Details on the methodology used and its accuracy are discussed. Preliminary results on discontinuity orientation, persistence and intensity are presented, highlighting the effect of observation scale. The potential uses of long-range terrestrial digital photogrammetry in open-pit mine and large natural rock slope environments is emphasized. The use of an f=400mm lens from distances larger than 1.5km may represent an important step forward in the geotechnical characterization of inaccessible remote rock faces.

May 1, 2009

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

By L Dixon, J Carter, K Auyong

Fourier transform infrared (FTIR) spectroscopy and other near infrared (NIR) tools have been used in the bauxite industry for many years. Infrared spectroscopy exploits the differences in chemical composition and lattice structure to produce a characteristic response. Spectral devices, such as those from ASD Inc and the HyLoggerTM, provide qualitative mineralogical data targeted towards hydrated minerals detected in the near and short wave infrared region. The FTIR spectrum extends into the mid and thermal infrared range and can therefore respond to the presence of silicates and oxides, in addition to hydrates and carbonates.The key to successful utilisation of infrared spectra, however, is the interpretation methodology. In this study, FTIR spectra were calibrated against quantitative X-ray diffraction data for the determination of the mineralogy of iron ore. A full pattern profiling machine learning technique was utilised for the calibration, and the assessment of the regressions determined from an independent validation set. The abundance of key minerals – hematite, goethite, kaolinite and quartz – were determined and the results correlated against X-ray fluorescence assays and loss on ignition data. The results of the study indicate that spectral techniques using a full-pattern profiling machine learning approach and artificial neural networks can be used successfully to obtain objective and quantitative mineralogical data to support field observations and analytical results for iron ore resource modelling. A comparison of this technique to the cost, quality and timeliness of other quantitative mineralogy tools is also made.CITATION:Carter, J, Auyong, K and Dixon, L, 2017. Determination of iron ore mineralogy using Fourier transform infrared spectroscopy and machine learning, in Proceedings Iron Ore 2017, pp 519–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

By Nutter R. S.

A methodology has been developed for qualitative safety hazard evaluation and quantitative reliability analysis of mine monitoring and control systems. Detailed application of these techniques were made to two commercial monitor/control systems and to a West Virginia University distributed microprocessor-based system. A controlled environmental test was conducted on a set of one of the commercial system's outstations. A software reliability evaluation methodology was also developed and applied.

Jan 1, 1982

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By J. Kretschmann, N. Nguyen

"The Vietnamese economic growth of more than 5% per year leads this country to an enormous demand for raw materials. In the duration of ongoing expansion, the big challenge in the coming decades will be to make this process as sustainable as possible when it comes to economic, environmental and social objectives. Risk management especially in occupational safety and health (OSH) in enterprises is one of the most important tools to achieve this aim. But until now, this has not been taken into priority by Vietnamese coal mining enterprises. Main reasons for this situation can be found in deficient legislative conditions and in non-synchronized risk management systems. In contrast, Germany has implemented an adequate legal system and the German mining industry has gained lots of experiences in risk management, especially in occupational safety and health. This paper seeks to point out specific challenges how to improve occupational safety and health in Vietnam by transferring and applying German methods and standards."

Jan 1, 2011