Search Documents

Agglomeration for Copper Heap Leaching Agglomeration of ore is a method which can be used to eliminate the migration of fine grained particles throughout a leach heap. Without agglomeration, fine ore particles are able to migration within the heap, clogging flow channels and producing large areas where access of the solution is poor. In order to gain the benefits of agglomeration and improve agglomerate strength even further in copper heap leaching, an economical, acid-resistant binder is needed. However, most binders have been used without any systematic reasoning. A set of novel testing methods were developed, including a soak test, percolation flooded columns, and larger long-term leach columns. The soak test compares the degree of breakdown when agglomerates are subjected to an acidic environment. While the percolation flooded columns and larger long-term leach columns evaluate the flow of leach solution throughout the ore bed. Systematic studies have been completed on a wide range of binders using these novel testing procedures. It was found that for a low grade chalcocite ore, which was rich in silica, from a southwest US mine, polyacrylamides reduced the fines migration the best in the novel soak test. The non-ionic binder, in particular, was found to reduce fines migration as much as 93 per cent. Several of the binders tested were shown to increase the hydraulic conductivities of the agglomerated ore up to 2.5 mm/sec, compared to a hydraulic conductivity of only 0.25 mm/sec when no binder was used. These binders also prevented 'slumping' of the ore, which indicates a decrease in breakdown of the agglomerates. The use of a binder also showed no interference with leaching reactions in long-term leaching experiments.

Sep 13, 2010

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Wang Hong Qu

This paper observes the shape of throw explosion crater its ejecta locus of internal medium and the process of distance along with slope's angle developing. It was discovered that initial velocity is inversely proportional to slope's angle. The velocity of surface distribution at the lower half crater of explosion is larger than at upper one. It carries the relevant calculated formula and physical process of explosion crater forming under the inclined boundary conditions, and some important law. It proved that the gravity influence is very distinct for the blast action in the little resistance line.

Jan 1, 1991

By C M. Hall

We report 40Ar/39Ar ages for adularia and illite from veins and wall rocks at the Waihi and Favona deposits, in the Waihi district. One sample of vein adularia from the Favona deposit yielded a plateau age of 6.04 ¦ 0.06 (la) Ma, and two samples of vein adularia from the Waihi deposit yielded plateau ages of 6.17 ¦ 0.03 and 6.17 ¦ 0.09 Ma. Two samples of wall rock adularia from the Waihi deposit yielded plateau ages of 6.07 ¦ 0.06 and 6.08 ¦ 0.03 Ma. Adularia ages overlap at the 2s level, and we do not consider them to be significantly different. Two samples of illite from wall rocks at Favona have total gas ages of 5.66 ¦ 0.04 and 5.65 ¦ 0.04 Ma, and retention ages of 6.57 ¦ 0.04 and 6.61 ¦ 0.04 Ma, whereas one sample of vein illite yielded a total gas age of 5.29 ¦ 0.17 Ma, and a retention age of 6.26 ¦ 0.19 Ma. The total gas ages of illite are minimum ages that are equivalent to conventional K/Ar analyses, whereas retention ages of illite are maximum ages. Although interpretation of the illite data is complicated, the adularia results strongly suggest that the Waihi and Favona deposits formed contemporaneously in the same fossil geothermal system at 6.0 to 6.1 Ma.

Jan 1, 2003

By B Xiao, J Yang, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Tuwu-Yandong Cu deposit, located in the East Tianshan mountains in the eastern section of the Central Asian Orogenic Belt, is the largest and economically most important porphyry Cu deposit in Xinjiang, China. It contains ~3 Mt of copper at an average grade of 0.46 per cent Cu and 0.2 g/t Au, with significant amounts of Mo and Ag. The deposit is mainly hosted in the Carboniferous Qi’eshan Group and plagiogranite porphyry, and is controlled by faults that are east–west-, north-west- and north-east-trending. Ore minerals in the Tuwu-Yandong deposit are dominated by pyrite, chalcopyrite and molybdenite, with minor bornite, chalcocite, magnetite, sphalerite and galena. Gangue minerals are mainly composed of quartz, sericite, chlorite, epidote, anhydrite, gypsum, muscovite, biotite, phosphorite, sphene, dolomite, actinolite, barite, albite and calcite. Based on the megascopic and microscopic textural relationships and mineral assemblages, five stages of hydrothermal alteration and hypogene mineralisation are recognized in the Tuwu-Yandong Cu deposit: the potassic stage, propylitic stage, phyllic stage, late veins stage and supergene stage. Most of the copper was deposited during the phyllic stage, along with less molybdenite.CITATION:Xiao, B, Chen, H, Wang, Y and Yang, J, 2015. Geology, mineralisation and alteration of the Tuwu-Yandong porphyry Cu deposit, north-west China, in Proceedings PACRIM 2015 Congress, pp 641–644 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

By Christian Wawrzyniak

An analysis method for modeling compensation grouting based on the finite element method is presented. By this method the design parameters of compensation grouting, grouting pressure and grouting volume, can be evaluated. Also the subsidence of a building due to tunnel driving as well as the lifting of the building by compensation grouting can be simulated. The stress changes in the tunnel lining and in the foundation of the building are computed as well. The application of the analysis method is demonstrated on two examples for compensation grouting in combination with construction of tunnels.

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

Despite the large areas of sedimentary basins in Western Australia, the coal resources are very meagre., This is a serious problem for the State, which-at present-lacks any other alternate source of fuel-for power production.. Located coal deposits are all poor in quality and mostly brown coals of little importance. The best..coal suitable for extraction is at Collie, where a black=sub- bituminous non-coking coal is mined. Most other coals recorded are low grade or lignite, with high ash'and moisture content and a low calorific value. Coal was first discovered in Western Australia in the bed of the Irwin River, 50-miles south-east of Geraldton, by the Gregory brothers, explorers, in the year 18+6,. but although investigated, it has never been developed. The most noteworthy discovery of coal was in the Collie River, 26 miles east of Bunbury, by Arthur Perrin in 1883. Production commenced in 1898 and ever since, Collie has continued to be the State's sole producing coalfield.

Jan 1, 1964

By McHenry Mosier

SUMMARY MERCURY is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies.

Jan 1, 1944

By William E. Ford, Edward Salisbury Dana

1. Normal Class (25) Barite Type 2. Hemimorphic Class (26) Calamine Type 3. Sphenoidal Class (27) Epsomite Type Mathematical Relations of the Orthorhombic System Crystallographic Axes. - The orthmhombic system includes all the forms which are referred to three axes at right angles to each other, all of different lengths. 296 Any one of the three axes may be taken as the vertical axis, c. Of the two horizontal axes the longer is always taken as the b or macro-axis * and when orientated is parallel to the observer. The a or brachy-axis is the shorter of the two horizontal axes and is perpendicular to the observer. The length of the b axis is taken as unity and the lengths of the other axes are expressed in terms of it. The axial ratio for barite, for instance, is a : b : c = 0'815 : 10 : 131. Fig. 296 shows the crystallographic axes for barite.

Jan 1, 1922

By Forrest T. Moyer

The safety record of the mineral and mineral-fuel mining and processing industries in 1966 was improved slightly for the second consecutive year as indicated by reduced injury-frequency and injury-severity rates. The overall operating activity was higher in 1966, as measured by the increased number of men working and the total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 17.38 per million man-hours in 1966. This overall rate comprised frequencies of 0.28 for fatal and 17.10 for nonfatal work injuries, compared with respective rates of 0.28 and 17.26 in 1965. Fatalities totaled 543; 5 more than in 1965. The total of 33.091 nonfatal injuries was 291 higher than in 1965. However, the larger number of disabilities was offset by the increased worktime in 1966. so that the fatality frequency was unchanged and the nonfatal frequency rate decreased from 1965.

Jan 1, 1967

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006

By R. J. Balfour, T. L. Papucciyan

"INTRODUCTIONCapital Cost considerations are basic to feasibility in the achievement of success for Mineral Processing Projects as much as or more than in many other industries. Capital cost is an important factor ae it 1R the unit of measurement for process engineering economic decisions. As a result of ever increasing complexity, alternatives of process and remoteness of site, there is an ever increasing emphasis on accurate estimating and the attendant cost control systems in the international market of today for the Mineral Industry where initial plant costs are becoming a more important factor than operating costs. An undervaluation means trouble ahead. An over-cautious assessment may bring an unnecessary abandonment of a project. Consequently, the ultimate cost must be predicted early and accurately and must be controlled to this parameter during the design and construction phases. Cost Est!~ mating is one of a variety of project management tools used to assist in planning and achieving the optimum balance between Quality, Cost and Time, the eternal triangle of evaluation, namely obtaining a project of acceptable quality at minimum cost and on time. In order to attain these established objectives, proper planning, organizing, coordinating, monitoring, adjusting and controlling the design, procurement and construction elements of the project are essential.This project management approach based upon the principle of a Task Force under single management, comprising a complete service organization, requires a substantial number of qualified individuals specialized in their own field and capable of working together as a team to perform their various functions effectively. The Task Force is supported by their chiefs of discipline and performs in accordance with established procedures and standards under the leadership of a Project Manager.General Engineering Company Limited with the backing of the full resources of Surveyer, Nenniger & Chenevert and its total staff of approximately 1,0009 offers the complete project management service to the Mineral Processing Industry of North America and the rest of the world. As mine sites become more remote and difficult of access, the need for an experienced team of specialists who work under the Task Force principle, with well established standards and procedures becomes even more important. Our long history of successful pro1ecta in this field has been our training ground for the fulfillment of this need."

Jan 1, 1972

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

By Susan P. Taite, Alain R. Charest, Peter D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in the southwestern Chihuahua state of Mexico (Fig. 1). A Francisco Gold geologist discovered the prospect in1995. El Sauzal was encountered as a result of an extensive grassroots exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas silver camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiaryage. The mineralization appears tobe structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system, including kaolinite, illite, alunite, dickite and pyrophyllite.

Jan 1, 2005