Search Documents

The development and introduction of a preventive maintenance scheme in the coke ovens department, coal preparation section, of The Broken Hill Proprietary Co. Ltd., Newcastle steelworks, is described together with its operation and the results achieved during the first 12 months.'fhe scheme consists essentially of an engineering analysis of the plant to establish maintenance schedules, and to record the details on reference cards.Items are reviewed progressively and a weekly work schedule is prepared, from which work orders are passed on to the maintenance foremen. These foremen in turn originate action orders and issue inspection sheets as required. Results are then reported back to the maintenance planner and used to revise norms, practices, and cycles.INTRODUCTIONWhat is maintenance? Some people consider maintenance to be the work involved in putting things together again after they have fallen apart. The author regards it as the mechanical care and repair of plant machinery and equipment to keep it operating in sound mechanical condition, without undue interference with production processes.Maintenance may be organized or haphazard, and, too often, what has been fondly imagined to be nicely controlled and organized maintenance proves, under pressure, to be more correctly described as haphazard. Haphazard maintenance deals with breakdowns as they occur, and frequently finds itself confronted with more breakdowns than can be handled. Even organized maintenance, if not based on sound planning, can, at times, be found in a chaotic state, because of unexpected and unanticipated breakdown.Properly planned and scheduled maintenance permits an orderly and controlled approach to the problem of maintain...

Jan 1, 1961

By Vance G. Leak

A technique for recovering copper and steel from metallic scrap has been developed by the Bureau of Mines based on preferential melting in molten salt baths at 1,150° to 1,250° C, The molten salt, preferably barium chloride or calcium chloride, both minimizes oxidation of the metals and promotes heat transfer. Cleanest separations (0.01 percent copper remaining in iron) have been achieved by pretreatment (dipping or spraying) with sodium sulphate or sodium silicate, which alters and coats the surface of the iron to inhibit the alloying or brazing with copper. An economic evaluation of the process was carried out on six combinations of sweating media and inhibiting reagents. On the basis of the postulated model, a cost of about $0.20 per pound of copper recovered has been determined for the sweating treatment operation.

Jan 1, 1973

By Theo. A. M. Salet

The historic centre of one of the most beautiful cities in Northern Europe -Amsterdam - is being excavated to accommodate the new North/South metro line. This new line is due for completion in 2012, and will link the Buikslotermeerplein district north of the harbour, underneath the Central Station and the old city with its gables and picturesque canals, to the commercial centre in Amsterdam Zuid/WTC. Three underground stations are being construction in the old city at Rokin, Vijzelgracht and Ceintuurbaan. The logistics of working in the middle of an historic city are demanding -maintaining tram, vehicular traffic and pedestrian access along narrow streets, providing suitable protection for the public alongside the working areas, arranging adequate delivery routes, as well as monitoring the old and mostly historical buildings for potential settlement. Safety of both the public and adjacent properties is paramount. Diaphragm walling - 1.2m & 1.5m thick and up to 48m deep - was chosen as the support system for the three deep metro stations. Challenging engineering as well as state-of-the-art equipment to construct the diaphragm walls was needed in order to meet the tight working specifications, in the narrowest locations imaginable. Extreme conditions call for innovative solutions.

Jan 1, 2006

The corrosion of aluminosilicate refractories by soda from three different sources has been studied by microscopic methods. Sodium sulphate from oil ash, sodium chloride used in glazing structural clay products, and sodium borate from borax-impregnated wood ash have fundamentally the same effect on the refractories. The soda is the chief medium of reaction and fluxing, the sulphur, chlorine, and boron being volatized as sulphuric, hydrochloric, and boric acids.INTRODUCTIONBecause of their strong fluxing action, alkalis are one of the main causes of corrosion and slagging of refractories.The action of potash and soda on refractories follows somewhat similar lines, although it is common for one alkali to be greatly in excess of the other. The course of the reaction in a number of cases of alkali attack has been studied by microscopic and chemical methods. For example, the action of potash on blast furnace refractories was studied by Kraner (1942) and Rigby and Richardson (1947), who described the occurrence of various potassium aluminium silicates. Its action on cement kiln refractories was described by Brisbane, Segnit, and Weymouth (1957). The action of soda on glass tank refractories has been studied by many people, for example Bisby (1956) and Resch (1954). Clews, Hugill, and Green (1940) made a microscopic examination of the attack by soda on silica bricks from a gas retort.Some recent cases of corrosion of aluminosilicate refractories which were brought to the attention of the Division of Building Research, C.S.I.R.O., illustrate phenomena which occur under conditions different from those...

Jan 1, 1964

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran, J. Zoric

A methodology for building pragmatic physics-based models is here adapted to predict the erosion of ladle linings in the steel industry, in order to support operators when deciding whether the lining can be used safely for another heat. A defective lining may allow 140 t of molten steel to spill, with disastrous consequences for workers and plant. The adopted work flow for the development, challenges faced, and some model results are presented. One key learning outcome is that model development should allow time for maturing the process understanding, as well as for many iterations by ‘questions-responses and actions’ at various stages in the model development. Good interaction between the development team and industry case owner is an important success factor. Combining or extending the model with the use of machine learning and cognition-related methods, such as knowledge graphs and self-adaptive algorithms, is discussed.

Apr 16, 2024

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used for making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By P. Zhang

The use of phosphate depressants in the cationic flotation of silica from francolite in the Florida phosphate industry is rarely practiced. The occasional use of gelatinized starch derivatives and pH adjustments to assure a slightly alkaline flotation feed slurry pH have been used in some processing plants to improve selectivity. This paper presents a preliminary laboratory comparison of several potential phosphate depressants for use with the flotation of siliceous phosphates. It was found that starch is ideal for floating fine (-35 mesh) silica from phosphate, while sodium tripolyphosphate may be the best for coarser (+35 mesh) feeds.

Jan 1, 2009

By Feng Liu

"With seven new applications for plans of work for exploration in the international Seabed Area approved by the Council during its twentieth session of the International Seabed Authority, 26 total approvals have been made by the Council up to date. Among them, three contracts were made with COMRA. On 8 August 2014, China Minmetals Corporation submitted another application to the Authority for approval of a plan of work for exploration for polymetallic nodules in the Area, which is also sponsored by the Government of the People’s Republic of China.China is one of the main contributors to the international seabed regime. The Presentation will describe China’s activities in the Area, such as exploration, technology development, environmental protection and policy making.JIAOLONG is a submersible with capacity of 7000 meters. JIAOLONG’s sea trials were carefully made in 4 years, from 2009 through 2012 and it successfully dove to a depth of 7062m in June 2012 at Mariana trench. A so called "Test Application Phase" started thereafter, and is planned to last for 3-4 years. Two cruises and 4 legs have already been made since then. A wide-range of findings were obtained during dives in South China Sea, and in COMRA’s Exploration Contract Areas for polymetallic nodules and cobalt-rich ferromanganese crusts. This presentation will reveal the colorful findings."

Sep 1, 2014

Several factors contributing to the loss of fibre during treatment are a function of the paragenesis of the veins. The occurrence, of magnetite from the cap rock within the veins prevents complete fiberization. There is a marked similarity between these veins and those in the Koegas-Westerberg area of South Africa.INTRODUCTIONAn investigation of the mineralogy of the Wittenoom Gorge crocidolite veins was undertaken in the latter part of 1962 at the request of the Colonial Sugar Refining Co. Ltd. It was anticipated that such a study might reveal the cause or causes of the lack of recovery of some asbestos during beneficiation. Some interesting features of the mineralogy and paragenesis of the crocidolite veins become apparent, but it is emphasized that the investigation is far from complete, as the study did not extend to the field occurrence.The samples examined were selected from the mill and from the untreated ore.GEOLOGICAL SETTINGWittenoom Gorge is situated on the Fortescue River in the Hammersley Ranges of Western Australia and is one of several gorges in these ranges, on the sides of which 'crocidoIite asbestos is known to occur. The Hammersley, Ranges consist essentially of a series of quartzites, shales, ferruginous quartzites and dolomites. These' rocks are part of the Nullagine Formation (Proterozoic) and are usually either horizontal or gently folded. In some 'areas small beds of riebeckite as well as crocidolite are known to occur interbedded in the sequence.Riebeckite is a monoclinic amphibole, the formula of which may be stated as Na2Fe2"Fe2" (OH) 2Si8O22, and crocidolite is a fibrous variety of this mineral. This formula...

Jan 1, 1963

By S. T. Kok

This paper presents a case study in West Malaysia for passive piles failure in very soft marine clay in open excavation. In this particular case, the thickness of the very soft marine clay ranges from 5 m to 7 m (16 ft to 23 ft) from the ground surface. Preliminary site investigation reported SPT ?N? value of zero for the very soft marine clay. The design was based on a deep foundation utilizing driven piles to support the superstructure. During pile cap construction, the piles were subjected to uncontrolled open excavation, inducing bending moment in the piles, resulting in some cracked and broken piles. Analyses were carried out using an existing three-dimensional finite element code with a non-linear soil model to predict the response of these piles during excavation. Finally, the predictions of pile responses during excavation were compared satisfactorily with the observed results.

Jan 1, 2009

By P. Taskinen, D. Lindberg, H. Viitala

The formation of copper chlorides in flue dust or deposits in heat recovery boiler of copper smelters or waste-fired boilers may lead to formation of corrosive partially molten deposits on walls and heat exchangers of the boilers. These deposits can contain various other metals, such as alkalis, Fe, Zn, Pb together with oxides and sulfates. In the present study, a thermodynamic model for copper-containing binary and ternary metal chloride systems within multicomponent CuCl-CuCl2-FeCl2-FeCl3- PbCl2-ZnCl2 system has been assessed and optimized based on own experimental phase equilibrium data, as well as literature data. The thermodynamic properties of the liquid phase was modelled using the quasichemical quadruplet model and a thermodynamic database was optimized to predict all available experimental data within the experimental error limits. The thermodynamic database allows for more accurate predictions of potential corrosion-related issues in various heat recovery boilers and waste-fired boilers due to formation of copper chlorides. INTRODUCTION In the copper flash smelting, flue dust can cause severe problems in the gas train, used for separating dust from the SO2-rich off gas, by forming corroding accretions on the walls of the heat recovery boiler. Formation of dust build-ups in the boiler need to be cleaned regularly and potential corrosion damage checked, requiring costly and unscheduled shutdowns of the flash smelting process. Compounds of copper and zinc among other elements having high vapour pressures may volatilize during the smelting of the copper concentrate, forming dust when the process gas cools down. Also, particles of solid or liquid iron oxides originating from the ore get transported with process gas to the heat recovery boiler as a result of entrainment in the flue gas (Miettinen, 2008) The dust deposit build-ups on the boiler walls are formed partly by direct impact of particles and partly by vapour condensation on the boiler walls. The initial deposition takes place by the condensation of vapours that contain zinc, lead, arsenic and other metals having high vapour pressures. Also, low melting point eutectic components of alkali salts such as chlorides and sulphates can act as sticky cohesive particles attaching to the boiler walls. The fine particles landing on the surface of the porous dust deposit layer react in the SO2-rich atmosphere of the boiler to sulphates. The process gas within the boiler contains SO2, O2, SO3, H2O and N2 that diffuse into the porous accretions to form a stagnant gas layer within the dust deposit structure. The composition of this gas layer may differ greatly from the composition of the process gas that is flowing on the surface of the accretion layer. Locally HCl and H2SO4 are formed and even a reducing atmosphere may exist within the dust deposit layer, allowing new reactions to take place. The local micro-atmosphere may enable metal sulphates to be reduced to secondary sulphides and even metallic components. Within the accretion layer, components may be formed that would not be stable in the gas atmosphere inside the boiler (Miettinen, 2008). This may be the mechanism by which for instance chlorides of Cu, Fe and Zn are formed within the deposit layer.

Jan 1, 2019

By B. E. Warren

Jan 1, 1965

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By J. Molgaard, J. Masounave, J. Prinsen, P. Beaulieu, G. Huard

"A study carried out on behalf of the National Research Council (NRC) indicates that economic losses due to wear in the Canadian mining industry are in excess of $700 million annually. Severe wear, mainly by abrasion, was identified as the most important wear mechanism in terms of possible savings. One way to reduce losses would be the proper use of databases. A joint project of The Canadian Institute of Mining and Metallurgy (CIM) and NRC (Tribology laboratories at IMRI) has been initiated to create a factual database containing all relevant experience in the area of wear in the Canadian mining industry. As a first step, a prototype covering slurry pumps is being built. This should help to answer many questions, such as the number of people involved, interest from industry, cost vs benefits, etc.IntroductionTribology is concerned with the understanding of the mechanisms of friction, wear, and lubrication.Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of those surfaces with lubricants, with the chemistry, physics and use of lubricants and their additives. It is concerned with the reduction of friction and wear (or, in the case of belts, brakes, clutch plates, and similar devices, in achieving optimum friction with minimum wear) and is concerned with the avoidance of associated failures in machinery.Lubrication is usually the solution to a problem of friction and wear. Yet far from all the problems of friction and wear are solved by lubrication. The wear of grinding rods or shovel track pads can hardly be solved by lubrication, to name just two examples with which mining engineers will be familiar. There are indeed many situations of wear and friction where the surfaces in contact are unlubricated.In part, tribology is a matter of design. A major aspect, however, has to do with the choice of materials, to satisfy external constraints upon the component design or choice. The operating conditions for much industrial equipment, particularly in mining are, often very severe. The development of wear resistant materials, including materials which are applied as coatings, is clearly an important technology from the point of view of tribology."

Jan 1, 1987

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and 80 percent oxygen should be discouraged because such mixtures are violently explosive and have led ,to fatal accidents.

Jan 1, 1940

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and SO percent oxygen should be discouraged because such mixtures are violently explosive and have led to fatal accidents.

Jan 1, 1940

By Ronald W. Schaefer

This report describes operations at the Rosiclare Fluorspar Works of the Aluminum Co. of America at Rosiclare, Hardin County, Ill. The works include the Fairview mine, the fluorspar mill, and related facilities. The publication covers exploration, development, mining and milling practices, mine-drainage problems, and other activities and is presented as part of the Bureau of Mines series of publications on mining and milling practices in various parts of the United States. The Rosiclare fluorspar area, for its size, has been the largest producer of high-grade fluorspar in the United States and probably in the world. The vein system in this area is over 5 miles long and 1/2 mile wide, and ore has been found as deep as 900 ft.

Jan 1, 1961

Significance of the body of iron oxide, which in part overlies as its hanging-wall the rich chalcocite ore-body at Mount Oxide, Queensland, has been variously interpreted by engineers and geologists who have inspected the deposit.Among the interpretations offered is the one that the body represents the residual of an original medium to low grade...

Jan 1, 1939

By B. P. Watson

Crush pillars have been incorporated into a mechanized, low-profile trackless system at South Deep Gold Mine. These pillars had to be designed to fail near the face and to ensure that pillar failure is contained within the pillar, to avoid bursting and the risk of high loads being generated during a seismic event, respectively. PoweRite backfill bags were recommended to maintain the integrity of the pillars; except in the main access drives, where the sidewalls were to be supported on 5.6 mm diameter weldmesh and yielding anchors. The results of a trial site investigation exceeded expectations, showing a residual pillar strength of about 37 MPa for a newly formed pillar and 8 MPa for a pillar subjected to seismicity and a closure of more than 300 mm. The introduction of these pillars has improved the rock mass conditions because of the active nature of the support, compared to the previous passive backfill method. Importantly, the pillars have increased mining efficiencies and improved face availability. A potential cost saving to the mine of R140.9 million could be realized over a period of 10 years.

Jan 1, 2014