Search Documents

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By Bhawani Singh, A. K. Dube, B. Singh

At least three hydroelectric tunnels constructed during the last decade through the lower Himalayan region in India have met with serious problems of supporting in squeezing ground conditions. Steel ribs under went intolerable deformations requiring rectification to provide space for concrete lining which delayed the projects inordinately. In an attempt to choose a rational method of predicting rock load, the authors have compared rock loads estimated from various classification systems and elasto-plastic theory with observed values. The deficiencies of the classification systems have been highlighted to show that the combination of elastoplastic theory and tunnel instrumentation programme provides better guidelines for the design of tunnel supports in squeezing ground conditions.

Jan 1, 1981

By Virgínia Morete Barbosa Bertolo

Ligas a base de zircônio são utilizadas na indústria nuclear devido à baixa absorção de nêutrons e alta resistência à corrosão em ambientes de alta temperatura e pressão. Nas condições de operação essas ligas estão sujeitas à fragilização pelo hidrogênio. Este trabalho visa avaliar o efeito do hidrogênio na liga ZirBrasil-1, produzida em forno elétrico a arco VAR (Vacuum Arc Remelting) nas condições: encruada e tratada termicamente. As análises de difração de raios-X indicam a existência de uma matriz Zr-a, hexagonal compacto, para todas as condições de tratamentos térmicos. Após a hidrogenação, ocorreu a formação de ZrH e ZrH2. Os hidretos formados são de pequeno volume e não conectados para as amostras laminada e tratada a 700°C/1 h e 800°C/2 h, sendo que a condição de 800°C por 6 h obteve a maior quantidade de hidretos por área e alguns hidretos conectados. Em todas as condições os hidretos se encontram espaçados ao longo da espessura das amostras. Os resultados de microdureza Vickers indicam a ocorrência de precipitação para tratamentos a 800°C e confirmam o efeito fragilizador do hidrogênio. A liga encruada absorve maior quantidade de hidrogênio, com início do processo de absorção ocorrendo após 12 horas, já a amostra tratada a 800°C por 6 h absorveu apenas 0,5%H e iniciou a absorção após 26 h. O conjunto de resultados permite concluir que a amostra recristalizada é a indicada para o desenvolvimento do processamento termomecânico, quando comparada a condição encruada devido ao maior tempo para início do processo de absorção e menor quantidade absorvida de hidrogênio.

Aug 8, 2018

By A. B. Parsons

LECTURE, it appears, is a discourse that is supposed to be instructive. I am quite sure that you will derive no instruction from what I have to say. I will be satisfied if my remarks provoke thought along one or two mental paths that have not been traveled so fre¬quently as to be devoid of interest. I have no particular message apropos of professional engineers or professional engineering, and any conclusions that I may seem to reach will be purely tentative and incidental. Probably at times you have wondered, in a casual way at least, why so many people who are not, never have been, and never will be engineers, want to use the title. For example, I recently received a communication from a life insurance broker or salesman, whose chaste letterhead bore the legend "Estate Engineer." He was perfectly serious about it, as is also the expert accountant who assumes the imposing name of cost-analysis engineer. Dozens of equally amazing titles might be cited. Then there is that class of individuals who have been engineers, in the true sense of the word; who have gone into some other kind of occupation; but who cling tenaciously to the name engineer, usually prefixing some word or other which at once gives them away by telling what their work really is. For example, we have such pseudomorphs as the management engineer, and the sales engineer. It is quite evident that engineer is a word to conjure with. Evidently both the man who appro¬priates the designation without any justification and the ex-engineer who persists in calling himself an engineer even after he has abandoned engineer-

Jan 1, 1933

By J. I. Paige

As part of a continuing effort to develop technology that maximizes mineral and metal recovery from domestic resources, the Bureau of Mines investigated a method to totally utilize copper converter slags without recycling them back through the matte smelting furnace. The research was directed toward (1) recovering the contained copper in converting slags by producing a recyclable copper-iron matte, (2) carbothermically reducing the slags to recover the iron, and (3) producing slag wool from the depleted slags. This report deals with the reduction of three industrial converting slags, containing 2.0 to 7.3 wt-pct Cu, in an 800-kVA electric arc furnace to produce a recyclable copper-iron matte. The addition of sufficient iron pyrite to provide 29 to 113 pct of the stoichiometric sulfur (based on producing 40-pct-Cu matte) produced a recyclable matte (36 to 61 pct Cu) at an energy consumption of 520 to 700 kWh per ton of solid material charged. The expected energy saving for treating molten slag in an electric furnace (5-to 9-MVA range) is about 400 kWh per ton of molten slag treated.

Jan 1, 1982

By Rolf A. Knopp

This paper discusses how design differences in FLP diesel equipment in underground coal mines came about. "Design standards" tend to create differences between countries while fostering uniformity among products of competing manufacturers. "Performance requirements," on the other hand, tend to eliminate differences between countries while encouraging competitive development of better products. Examples of regulations from the U.S., Canada. Great Britain. Australia. South Africa, etc., are used to illustrate differences in the design and certification of diesel equipment for underground coal mines.

Jan 1, 1978

By James S. Graham

Foundation pile driving hammers used in New York City in the past 100 years have been drop, steam, compressed air, diesel, and hydraulic. In 1992, the first hydraulic hammer in the New York City area was purchased by Norwalk Marine Contractors, Inc. from Junttan in Finland. It was bought because of its variable energy and ease of mobilization, not because of its higher transferred energy. Heller and Johnsen engineers instrumented hydraulic hammers on nine jobs. The measured transferred energy for the nine jobs was found to average approximately 80 percent. There is no clear consensus regarding the reasons for the hydraulic hammer being more efficient in delivering energy to the pile as compared to single-acting steam/air impact hammers. To minimize pile damage during installation, and to minimize footage overruns, an up-to-date version of the wave equation software that includes an efficiency value of 0.95 for hydraulic hammers is now used.

Jan 1, 2000

By P Holtham, K Duffy, W Valery, A Jankovic

In the face of increasing energy costs, limited water resources, more stringent legislation, and lower feed grades, the mining industry is searching for more sustainable technologies and practices. Metso Process Technology and Innovation (PTI) is undertaking a research project, ‘improving the resource and eco-efficiency of mining operations’, to help the industry meet these challenges. The project is investigating alternatives in mining and processing that reduce energy and water consumption, minimise emissions and waste, and maximise the value recovered from the deposit. The targets are to reduce energy usage by more than 30 per cent and greenhouse gas emissions by more than 50 per cent compared to current practice.Key areas of interest were identified across mining and processing operations. These were grouped into the following interrelated work areas for investigation: high intensity selective blasting, in-pit crushing and conveying, preconcentration, energy efficient comminution circuits and technologies, coarse particle flotation, and water recovery optimisation. Investigations have included reviews of industrial data, modelling, simulation, and laboratory and pilot scale trials. In some areas industrial scale trials will commence shortly. This paper discusses the investigations and key findings from the project so far; highlighting the possibilities for reducing energy consumption, water usage and carbon emissions. A particular mining process may incorporate any combination of the alternatives identified and requires tailored solutions based on a detailed understanding of the ore deposit, the process and local conditions. The focus is on improving resource efficiency; creating more value with less impact and consequently a better economic return from the available resource. Technologies exist today that can transform mining into a more efficient industry for tomorrow.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Resource efficient mining processes of tomorrow, in Proceedings Third International Future Mining Conference, pp 227–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By K. Leutwyler

The key to realistic casing stress analysis in thermal recovery installations is accurate knowledge of the temperatures involved. Much information leading to prediction of heat losses from tubing string to wellbore has been published. This .same information permits calculation of casing temperature under certain conditions. This paper reviews the basis for most of the published work, the line source solution to the diflusivity equation and examines some of its application criteria in the light of unsteady-state conditions. An alternate finite differences method is presented for correlation, and experimental data pertaining to the heat transfer mechanism in the annulus is reported. In the light of the information presented in the paper, it appears that the assumption of a line source for the tubing-wellbore system is valid even for reasonably short periods of heat flow, .such as "steam soak" operations. The empirically modified equation presented earlier matches computer derived results of the finite differences approach lor periods as short as 50 hours. Previously predicted cas ing temperatures and the associated stress levels are thus verified based on these correlative computations and the reported experimental information. Fall out from the computer output resulting in some studies of the influence of insulating cement properties on casing temperature, and experimentally studied effects of nitrogen placed in the annulus at various pressures., are described. INTRODUCTION Generally speaking, predictions of average casing temperatures have been based on an idealized model involving a centralized tubing string at uniform constant temperature radiating energy towards the casing under steady-state conditions.'. ' Heat is transferred away from the casing to the formation by unsteady-state conduction across thermal barriers consisting of cement and the mud sheath. Heat balances written on the casing permit prediction of instantaneous casing temperatures. During early periods of injection, casing temperature varies appreciably as a function of time; however, for long injection times this variation decays as heat flow from the wellbore to the formation stabilizes, and it becomes virtually negligible as conditions surrounding the wellbore become quasi-steady-state (Fig. 1). Carslaw and Jaeger -escribe a solution to the diffusivity equation for a line source (Fig. 2). A constant supply of heat is introduced into the medium from the line placed into the origin of the x-y coordinate system and parallel to the z-axis. Heat spreads outward in the infinite cylindrical solid and the temperature increase on a line going through point (x, y) parallel to the z-axis at a distance r can be predicted by: The following criterion must be considered: the Carslaw and Jaeger equation is obtained on the basis of a large

Jan 1, 1967

By A. J. Basu

New technologies, such as computer based learning, wireless computing, internet2, online courses, distance learning, and in general multimedia applications are being implemented in the higher education sector in an increasing manner. However, these implementations are not coherent, and lack standards. However, one example of the existing standards is the development and implementation of the virtual learning environments. These technology tools help in delivering the eLearning objectives. There is a major initiative in Europe (eEurope action plan) in promoting eLearning towards creating a knowledge-based society. Technology implementation is the major driver for achieving the eLearning objectives. A two-year pilot project on implementing technology tools including virtual learning environment (VLE), video-conferencing, and simulation and visualization was carried out for providing a blended learning environment for undergraduate and graduate students in Mining Engineering (undergraduate) and Mineral Deposit Evaluation (M.Sc.) course at the Imperial College London. The pilot project was funded by the Imperial College Centre for Educational Development (ICCED). The project did contribute towards activities for creating an institute-wide eLearning strategy in line with the eEurope action plan.

Jan 1, 2003

By Erik Melchiorre, M. Katherine Crombie, Dante Lauretta, Chris Gholson

Rich Hill, also known as Weaver District No. 2, is among the most productive placer gold locations in Arizona. Located near Congress, AZ (Fig. 1), this district hosted major placer rushes in the 1860s and1930s. Those rushes were followed by an electronic metal detecting rush that started in the 1980s and continues today. Thousands of ounces of gold have been produced by these modern amateur and professional metal detectorists. Many of them see more gold in an afternoon than Nevada mine workers will ever see outside of the mill. Rich Hill discovery Inspired northeastward by Spanish legends, a party of 10 men left Yuma, AZ on April 1, 1863. Included in the group were Pauline Weaver (Fig. 2), Henry Wickenburg and Abraham Peeples. Wickenburg left the group near the Hassayampa River and discovered the Vulture deposit. The rest of the group arrived at the base of Rich Hill in late May. While drying antelope meat on the first day, a few of the men prospected a nearby creek bed and immediately found gold. In a couple of hours they picked up more than 2.8 kg (90 oz) of gold. The next day, four members of the party went searching for their horses and returned with news that a nearby hilltop was literally graveled with nuggets.

Jan 1, 2003

By D. H. McCain

Through a unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT) Center, a video packed, dazzling CD-ROM training program was developed for new miners entering the aggregate industry. Why this product was developed, and why the aggregate industry, will be discussed along with the challenges faced throughout the project. Cooperation from every one involved including MSHA made this the product of which all other training materials in the mining industry will be measured against in the 21st Century. This product's versatility and wide application makes it a tool that is as critical to a mine's success as any earth moving machine. Developed with both state and federal grant moneys allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2001

By S. Ndlovu, M. Malatse

"The Witwatersrand Basin is the heart of South Africa’a gold mining industry. The cluster of gold mines located in the Witwatersrand Basin generates a significant amount of mine tailings, which have adverse effects on the environment and ecological systems. In addition, disposal costs are very high. The exponential population growth in the Witwatersrand area has resulted in pressure on the reserves of traditional building materials. Quarrying for natural construction material is very expensive and damages the landscape. This work therefore examines the use of gold mine tailings in the production of bricks.Different mixing ratios of gold tailings, cement, and water were used. The resulting bricks were then cured in three different environments - sun dried, oven dried at 360°C, and cured in water for 24 hours. The bricks were then tested for unconfined compressive strength, water absorption, and weight loss. The results showed that the mixture with more cement than tailings had a compressive strength of approximately 530 kN/m2. It was also found that the best brick curing system was in a water environment. Bricks made from tailings cost more than conventional bricks because of the higher quantity of cement used, but the manufacturing process consumes less water. Overall, the results indicated that gold mine tailings have a high potential to substitute for the natural materials currently used in brickmaking.Paper written on project work carried out in partial fulfilment of BSc. Eng. (Metallurgyand Materials Sciences)"

Jan 1, 2015

The ore treatment expansion programme at Mount Isa Mines required the erection of a new lead-zinc concentrator to be known as No. 2 Concentrator. This concentrator was designed by Western-Knapp Engineering Company in conjunction with staff of Mount Isa Mines Limited. Metallurgical design followed conventional wet milling practice, but the size of many plant units is larger than previously used at Mount Isa. The. total capacity of the new plant is 150,000 tons per four weekly period, and the plant is designed to operate in two equal parallel sections.Erection was contracted on a turnkey basis, and the plant was commissioned as a production unit on 23rd June 1966.The existing concentrator, No. I, was converted to treat all copper ore, and the total capacity of the two plants is now 390,000 tons per four weekly period.

Jan 1, 1968

By D. P. Roberts

This paper reviews the use of crush pillars on mines in the Bushveld Complex and the Witwatersrand Supergroup. Stress measurements were undertaken in order to determine the residual strength of these crush pillars. The results from these stress measurements are compared with previous attempts to determine the residual strength of crush pillars using back analysis. It is concluded that the residual strength of such crush pillars lies in a band between 13 MPa and 25MPa. Using the data from the stress measurements, as well as published and unpublished data, a stress-strain curve for a crush pillar with a width-to-height ratio of 2:1 is proposed. Where further work is required, this is indicated in the text.

Jan 1, 2005

By Steven Hoerger

Newmont Mining has a large, integrated gold-mining operation in northern Nevada with several mines, stockpiles and processing facilities. There are more than 90 defined metallurgical ore types and more than 60 defined gold-recovery process options. Newmont developed a mine plan and process model to take better advantage of the available synergies at its Nevada mines. This plan includes a mixed integer and linear programming optimization tool. This system is maintained and operated by a Nevada planning group. Standard in-house planning software tools and methods have been implemented at all mine sites. These changes have allowed a reduction in mine engineering staff and have increased the effectiveness of mine planning.

Jan 1, 1999

The process of electrostatic separation was developed in the late 19th century, but did not make much headway for about 25 years. High dc voltages, of the order of 20 kilovolts, are involved, and the only means of obtaining such voltages at that time were by the use of frictional machines, such as the Wimshurst. These were not reliable, for two reasons:-a. If a spark discharge occurred it took an appreciable time before a steady voltage was again attained.b. In damp weather the machines were almost useless.In the first 20 years of the 20th century the advent of mechanical and vacuum-tube rectifiers led to promising developments of 'the process. In the early 1920's flotation became widely used commercially, and proved to be more reliable, and capable of wider application, than electrostatic separation. During the last 15 years or so, with a better knowledge of the fundamentals forming the basis of the process, electrostatic separation is beginning to compete with flotation, especially in the treatment of smallsizedgranular material, such as beach sands. Electrostatic separation can be, and is, widely used in many cases where flotation is impossible, such as in the cleaning of food products which must be kept dry.

Jan 1, 1950

By Tellis D. A

An outline is given of the general position of earthsciences information in Australia, the background to development of the Australian Earth Sciences Information System (AESIS) and the role of the Australian Mineral Foundation in developing and co-ordinating the projeot in co-operation with the CSIRO, BMR, National Library of Australia, AGIA, and many companies.Details 'of the system, method and anticipated rate of input (especially of unpublished material at which the System particularly aims), mode of dissemination, and use of the data base are discussed. Information on theAustralian Thesaurus of Earth Sciences and Related Terms and brief details of some 30 earth sciences information collections in Australia is given.

Jan 1, 1977

By S McKinley, S Juras, E Uludag

More and more, today’s mining geologists are asked to identify and create 3D value domains for multidisciplinary usage: grade definition, geometallurgical performance and geotechnical characteristics, to name a few. Often, that domain shape is the result of an assumed or conjectured value as a surrogate to a set of conditions (eg kaolinite-rich, sericite alteration). Would it not be instead better to create the respective domain through identification of a consistent quantifiable geologically-based pattern as its basis?Critical to the identification of patterns is the transformation of 3D point data into a model by a method that uses few, if any, preselected thresholds. Too often we complicate the reviews of the modelled data by prejudging the value range of interest. And when we do revert to 2D views (ie sections and plans), we tend to only examine numbers or line traces. These hinder and obscure identification of geological patterns particularly in deposits of complex geology. Instead, these data should be looked at with minimal prejudgment and interrogated in 2D space by one of the best and most eye-catching display types: filled contour plots.Here we present two different processes that transform data with minimal preselection into formats that allow for pattern recognition by filled contour plots. These are: probability assisted constrained kriging (PACK) and multiple interval interpolant formation (Aranz Geo’s Leapfrog® software). The former creates a 3D model of probabilities on a threshold value; the latter creates numerous (=10), regularly-binned 3D interval interpolants. The results of each method are examined as filled contours over numerous sections or plans. Any distinct patterns are quickly discerned thereby readily identifying the best value to base the creation of a domain. These processes therefore provide a way to marry recent advances in software tools with what is supposed a geologist’s core skill: pattern recognition.CITATION:Juras, S, McKinley, S and Uludag, E, 2017. Pattern recognition in transformed data – the search for domain shapes in mine geology data, in Proceedings Tenth International Mining Geology Conference 2017, pp 37–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By T. A. Kirk

"The Linatex Dewatering System is a compact, low capital and maintenance cost matched set of processing equipment suitable for solids recovery, dewatering and desliming sand-like materials in the range 3/8"" to 325 mesh ( 1). Since its introduction to North America in the early 1970s, various elements of the system have been successfully installed in a variety of applic11tions both in Canada and the U.S.A. Examples are chosen from the coal, fine aggregates, iron ore and industrial minerals industries.II. Elements of the Linatex Solids Recovery System(A) The Linatex Separator (See Fig.I)The Linatex Separator, which is the heart of the system, is a specialized type of hydrocyclone designed to give a self regulating rope discharge product. It has the familiar cyclone geometry of cylindrical and conical section, tangential inlet, apex and vortex finder. The apex is enclosed in a unique patented automatic underflow regulator consisting of a collapsible rubber sleeve, and the overflow line is a siphon-leg, with a controlled air bleed valve. The siphon leg is adjusted so as to balance the internal negative pressure acting as a closing force on the underflow regulator against the mass of slurry pressing down on it from the cone section of the Separator. With correct adjustment the underflow regulator will close drip-tight on a water only feed. As solids accumulate in the apex of the cone the weight of solids counterbalances the vacuum and cat1ses the underflow regulator to open and discharge classified material at a controlled density."

Jan 1, 1978