Search Documents

By Mark Maday

As part of the I-94 North-South Corridor reconstruction program, the Wisconsin Department of Transportation (department) is reconstructing the Mitchell Interchange in Milwaukee, Wisconsin. Located on the south side of Milwaukee near Mitchell International Airport, The Mitchell Interchange interconnects I-94, I-43 and I-894. Reconstruction began in 2009 with the letting of the first advance contract for local crossroad bridge reconstruction. A second advance contract for construction of collector-distributer roads on each side of the I-94 mainline was completed in 2010. The main contract involving reconstruction of the core of the Mitchell Interchange was let in the summer of 2010, and is scheduled to be completed by the end of 2012. The core contract includes construction of three cut and cover tunnels along two system interchange ramps. Construction of the three tunnel structures is on the critical construction path. The contract includes an interim contract completion date that requires the tunnels to be open to traffic by the end of 2011. A top down method of construction using drilled shaft secant piles for the sidewalls of the cut and cover tunnel structures was selected as the preferred structure type to address subsurface and construction schedule challenges. The department identified in pre bid coordination that no cost reduction incentives would be reviewed or accepted for changes in tunnel wall type. A major component of the tunnel structures requires the installation of 1,500, 4-foot diameter secant piles. This paper presents mitigation strategies to manage construction risks associated with the installation of the secant piles including; prequalification of the secant pile subcontractors, requirement for use of full depth temporary casing, a site specific quality control plan, specifying drilling equipment, and developing a geotechnical baseline report for this critical component of the Mitchell Interchange reconstruction project.

Jan 1, 2011

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008

By Y. K. Yen, J. D. Miller, C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA)system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

The oxidation of ferrous sulphate to ferric sulphate with air and oxygen in a gas lift percolator was investigated with initial Fe2+ concentrations in the range 0·01 M to 1·0 M,temperatures in the range 20-80°C, and pH in the range oto 2.The rate of formation of Fe3+ was found to be well described by the rate expressionEquation 1and a consistent mechanism is proposed.The presence of Cu2+ was found to cause an increased rate of oxidation, the effect being greater with Cu2+ concentrations increasing in the range 0·001 M - 0·01 M in 0·2 M Fe2+. The effect of other solutes containing Ni, Zn, Mn, Co, Hg, Cl, Mo, NH4, As, Cr, or Na at a concentration of 0·001 M in 0·2 M Fe2+ was negligible.

Jan 1, 1972

Mineralogical analysis of a nickeliferous laterite from the Rockhampton region shows that the nickel is largely associated with the manganese wad and opaline silica. The laterite also contains an appreciable chromite content (about 12 per cent Cr2O,) although this tends to be poorly liberated.Leaching with hydrochloric or sulphuric acid, at atmospheric pressure at the boiling point is non-selective with respect to iron dissolution.The degree of dissolution increases as the acid concentration and retention time are increased; cobalt dissolution requires less aggressive conditions than does the dissolution of an equivalent amount of nickel.Leaching with sulphuric acid at elevated temperatures and pressures leads to a minimum amount of iron dissolution, is rapid, and requires a reduced acid addition rate. Nickel and cobalt recovery from the clarified leachate would be simplified because of the leach selectivity.Pressure leaching appears to be the most practical route for treating the Rockhampton laterite. The economics of processing would be made more attractive by the recovery of a chromium concentrate from the leach residue. This would typically contain about 45 per cent Cr2O, and could be used as a source of chromium chemicals.

Jan 1, 1986

Predicting Water Recovery from Flotation Cells

Sep 13, 2010

By R. Halatchev

This paper treats the spatial aspect of mine sequence optimization, revealing it in the context of determining the optimum number of cutbacks of an openpit mine. Cutback mining is currently a dominant method in the mining of base and precious metals. It is based on a pseudo-economic discretization of the pit space using advanced pit design algorithms. The result of implementing such an approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks to maximize project value. In this paper, the development of a mathematical solution of this problem using combinatorial analysis is presented. The solution provides a multivariate investigation of the optimum mine sequence with the implementation of a method for production scheduling optimization that uses Net Present Value (NPV) as a criterion for assessing the economic efficiency of mine sequencing. A case study using the conditions of a hypothetical openpit gold mine is provided to illustrate the applicability of the approach. The results obtained reveal the complex nature of NPV variation as a function of the cutback geometry.

Jan 1, 2015

Resolution Copper Mine is planned to be a 2000 m deep panel cave mine with virgin rock temperatures above 80°C in rock with a high crystalline silica content. The planned run-of-mine production rate is 120 kt/day. The project is in prefeasibility evaluation. This paper discusses features of the ventilation system design, which include multiple ventilation shafts with total flow of about 3000 m³/s and both surface and underground refrigeration systems with more than 140 MW total capacity. This will be a very challenging mine to ventilate, but this work has demonstrated that it will be technically achievable with the application of existing technology.

Jan 1, 2014

By Francis Church Lincoln

I. SITUATION AND SURROUNDINGS. THE Promontorio mine is situated at the northern end of the Sierra San Francisco de Coneto, in the town of Promontorio, Partido of El Oro, State of Durango, Mexico. As shown in the sketch-map, Fig. 1, the nearest railroad station is Chinacates on the Mexican International Railroad, 82 miles north of the city of Durango. The mine is 16 miles north of the station by air-line. It is reached by means of a good wagon-road which first crosses the Guatimapé Plain, passing the ranches of San Antonio and San Julian, to Estacion-a distance of about 15.5 miles-and then entering the mountains crosses the Sierra to Promontorio-a further distance of 11.5 miles¬making in all a distance of 27 miles by road from railroad to mine. Promontorio is just beyond the summit of the range, at an elevation of about 8,000 ft. above sea-level, or 1,350 ft. above the Chinacates station. The Castillo de San Francisco, the highest peak in the Sierra, has an altitude of 10,000 ft., and the Promontorio road crosses the summit of the ridge at an elevation of 9,000 ft. by a pass just below this peak known as the Puerto del Almagre. The Promontorio mill is situated at Santa Ives, 2 miles by tram or 3 miles by wagon-road to the north of Promontorio and about 600 ft. lower. The Sierra San Francisco de Coneto decreases in height towards the north and west till it comes to an end at the Melchor Arroyo on the ranches of Melchor and Ramos. Beyond this arroyo another range, the Sierra de la Candela, begins. In the vicinity of the Promontorio mine the hills are very rugged and the surface is furrowed by ravines which contain running streams during the rainy season-July, August and

Jan 1, 1908

By H. D. Mellom

The direction of the optic or "C" axis of a uniaxial metal crystal can be found with the metallurgical polarizing microscope by examining two planes of section on the crystal. Complete orientation of the crystal can be determined if a twin crystal is common to both surfaces of section. Examination of Uniaxial Metals in Polarized Light-Rotation of a uniaxial crystal surface, properly prepared,' shows four extinction positions 90 deg apart, provided that the surface is not close to a basal section. One of these two extinction directions corresponds with the projection of the optic axis on the surface of section. This direction can be found if the 'sign of the rotationr2 for the metal is known. To find the direction of the optic axis, the crystal is rotated on the stage 45 deg from an extinction position. With a crystal of negative sign, to produce extinction the analyser must be rotated towards the optic axial direction and vice versa. All sections, other than basal, of a uniaxial crystal have the same sign of rotation and, since there is no change in sign with wave length, white light can be used for these measurements. U the sign of the rotation is not known the presumed direction of the optic axis can be determined assuming a positive sign. A third section cut normal to the presumed optic axis will show basal extinction if the assumption is correct. It is convenient to use the edge between the two planes of section as a fiducial direction common to both surfaces. The optic axis can be related to this direction. If the above measurements are repeated on the other plane of section and the angle between the two section planes measured, stereographic projection can be used to determine the orientation of the crystal optic axis. Determination of Complete Orientation—The complete orientation of a uniaxial crystal can be determined provided that a twin crystal is common to both surfaces of section, and the twin law is known. The orientation of the twin crystal optic axis can be determined in the same way as for the main crystal

Jan 1, 1962

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By B. M. Hamilton

"IntroductionTHE PROCEDURE and technique for drilling holes has probably undergone as great a change during the past ten years as any one of the other operations conducted in hard-rock mining. During this period, we have seen a change from the heavy leyners and drifters to the light jackleg type of drill machine; from steels that were forged and hardened on the bit end to the inserted •carbide-tipped rod, from the necessity of providing special bit-end fabrication and beat treatment of shank steels to the simple grinding or turning of a plain section on a shank with no heat treatment required for bit attachment.When the steel maker was first called upon to manufacture a hollow drill rod, it was required that the steel must not only have sufficient strength and fatigue resistance to cope with the stresses of service, but also must be capable of being heat treated on the bit end to a high hardness for resistance to wear and abrasion . Little was known at that time about alloy steels and the beneficial effects to be gained from additions of chromium, nickel , and molybdenum. So it was that the plain 0.80 per cent carbon analysis was selected, since it had already proven to be a suitable grade for chisels, hammers, and other such shock tools. This grade has long endured the test of time and is still used in considerable tonnage today, particularly by the construction industry.As the metallurgist learned more about the influence of alloying elements, a new hollow drill analysis was placed on the market in the early 'thirties'."

Jan 1, 1954

By Thomas J. Wright

The evaluation and development of the Eastern North Carolina phosphate deposit resulted in one of the world's largest and most modern phosphate mines and fertilizer complexes at an investment in excess of $90,000,000. The resulting ore beneficiation process showed excellent correlation with pilot plant data. A number of variations from current industrial practices were introduced and projected from bench scale tests through pilot plant to production. Principal among these variations were the following: 1) removal of magnesium by classification, 2) simultaneous flotation of coarse and fine phosphate, 3) the use of saponified fatty acid, 4) utilization of filter wash water for deoiling, 5) utilization of a rougher concentrate for acidulation, 6) calcination of flotation concentrates, and 7) elimination of grinding prior to the manufacture of phosphoric acid.

Jan 1, 1971

By Andrew Thallisson de Souza

Os aços inoxidáveis ABNT da série 300 são ligas austeníticas Fe-C(< 0,08%) - Cr(18 a 20%) - Ni(8 a 10%) são muito aplicados, pois apresentam alta estampabilidade, alta soldabilidade, boa resistência à corrosão uniforme em vários meios corrosivos, no entanto, sofrem corrosão localizada (pites, corrosão sob tensão, fresta e corrosão intergranular). Os aços inoxidáveis da família UNS S32304, têm 23%Cr e 4%Ni. Por terem teor de carbono inferior a 300ppm (0,03% em massa) são resistentes à corrosão intergranular, sofrem pites e corrosão sob tensão (CST). Devido ao alto teor de cromo, o aço UNS 32304 apresenta boa resistência à corrosão uniforme, sendo que na corrosão por pites o mesmo apresenta um comportamento melhor que os aços ABNT 304 (sem Mo) e ABNT 316 (com Mo), de acordo com o Número Equivalente de Resistência ao Pite (PREN). O PREN dos aços UNS 322304 é 26, e para os aços ABNT 304 e 316 são 18 e 25, respectivamente. Este trabalho caracterizou os diferentes aços inoxidáveis química, metalográfica e eletroquimicamente em meios contendo íons cloretos. A partir de ensaios de caracterização eletroquímica, por polarização potenciodinâmica, verificou-se que o aço ABNT 304 apresentou potencial de pite inferior aos aços ABNT 316 e o UNS 32304, em soluções aquosas contendo 3,5% (massa) de NaCl. Verificou-se que estes aços sofreram CST empregando-se ensaios de deformação (corpo de prova em U) e carga constante (corpo de prova de tração liso) nos eletrodos em soluções aquosas contendo 42% (massa) de MgCl2 na temperatura de aproximadamente 143°C. Salienta-se que o comportamento em CST do aço ABNT 304 foi inferior aos demais. As amostras ensaiadas foram caracterizadas fratograficamente (macro e microfratograficamente - empregando-se microscopia eletrônica de varredura). Os corpos de prova que sofreram CST apresentaram facetas de clivagem e “marcas de rios”, características da fratura frágil.

Aug 17, 2017

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

The additional information that Clarke and Taylor (1982) provide about the important but poorly documented Ardlethan deposit is, of course, very welcome. However their contention that structural considerations, in conjunction with petrology, alter the interpretation of the mineralogical and geochemical data presented previously (Scott, 1981) is not accompanied by adequate supporting evidence. Indeed characteristics of the orebodies studied invalidate their arguments.Heterogeneity between matrix and fragments is not a problem in the South Cherry and Ardwest orebodies because most samples are comprised entirely of interlocking hydrothermal assemblages with a fabric and mineralogy that is uniform through both former breccia fragments and matrix. In hand specimen, the rock superficially resembles altered granite and, as indicated by Clarke and Taylor (1982), a brecciated texture is difficult to discern. In thin section, relict brecciated textures can be observed as localized changes in the grainsize or in the distribution of minerals that outline former breccia fragments (P. J. Eadington, 1982, personal communication).Because of the intense brecciation and comminution of rocks (fragments < 10 mm are usual) in the South Cherry and Ardwest breccia bodies, hydrothermal recrystallization was complete, resulting in homogenization of fragments and matrix. Furthermore, the amount of sample analysed (-100 g for drill core and 2-3 kg for hand specimens) is sufficiently large to be representative of both former breccia fragments and matrix. The Carpathia and Stackpool orebodies, with their abundance of sedimentary fragments, have alteration superimposed on a heterogeneous fabric, and were not studied. Thus the problems of differentiating between fragments and matrix (Clarke and Taylor, 1982) are irrelevant to the particular orebodies described in my paper.Within the alteration halo, which is several hundred metres wide (Paterson, 1976), the very uniformity of the alteration assemblages implies that subsequent, postmineralization brecciation is of only minor significance.Indeed tourmaline pipes in the Ardwest pit are less than several metres across (Clarke, 1979) and produce minimal alteration in the surrounding rocks. Therefore the interpretation of the mineralogical zonation is not compromised by the recognition of several periods of brecciation.

Jan 1, 1982

By Laura McNally

In 2006, McNally International Inc., in a joint venture partner-ship with Aecon Constructors, was the successful bidder on two York Region Tunnel Projects: the Bathurst Collector/Langstaff Trunk Sewers and the York Durham Sewer System (YDSS) Interceptor Sewer 19th Avenue, both in the Toronto area. These projects comprised a total of 13 km (8 miles) of 2.74 m (9 ft) finished diameter tunnels and are both part of the YDSS. Both contracts required the use of earth pressure balance (EPB) tunnel boring machines (TBM) with a precast concrete segmental liner.

Jan 1, 2008

By A A. Latscha, D O’Connor

Increasing orebody complexity, restrictions in ground access, and longer lead times for disturbance approvals, have generated the need for the Resource Development Team within Rio Tinto Iron Ore (RTIO), to explore optimised drill design techniques that deliver resource conversion value while maximising program outcomes. In response to this challenge, the Team initiated a case study to produce an AI assisted/designed drill program using a non-machine learning AI. The case study involved the assessment and implementation of an AI generated drill program at one of RTIO’s Pilbara iron ore deposits, located in the Hamersley Province of Western Australia. The Mineral Resource is currently classified as 100 per cent Inferred. Access constraints inherent to topography, and the presence of exclusions zones have prevented adequate drilling coverage, resulting in lower resource confidence and a poor definition of the orebody extents and geometry. The drill campaign, planned in Q1 2023, needs to consider access constraints, complex topology and the limitations related to additional ground clearance, while addressing the requirement of improving orebody knowledge. The drill plan had to address two objectives. The first and main aim of drilling was to upgrade the Resource Classification to allow for possible conversion to Ore Reserve. The input for this objective was a volumetric representation of the areas currently not meeting pre-defined quantitative Resource Classification upgrade criteria. The second objective was to better define the orebody extents and geometry. For the second objective, the input to the drilling optimiser was a volumetric representation (blocks) of the areas of high uncertainty in the mineralisation/waste boundary, which were defined using an indicator conditional simulation technique. The drilling optimiser output was a range of compliant drill plans. A set of KPIs based on economic and orebody knowledge criteria were used to assess the plans and to select the most optimal drill design to be drilled in 2023. The geology and management teams were able to make better informed, objective decisions using the trade-off between cost and orebody knowledge gained. As part of the assessment, the AI generated plans were compared to our current planning practises. The AI assisted plans, when gauged against the project KPIs, showed clear and measurable improvements in both meeting project objectives and in managing operational risk.

May 24, 2023

By Gerald M. Ellis

ntroduction As the gold mining industry continues to develop in the Dominican Republic and Haiti, more deposits will undoubtedly be discovered that will be amenable to development. The Pueblo Viejo gold mine is currently in operation in the Dominican Republic. It has become an important component of that country's economy. Pueblo Viejo output is important to the government as a foreign currency earner. It is also said to be among the world's more successful gold mines. But, while Pueblo Viejo is successful, no other major gold discoveries have been made in recent years. Therefore, alluvial deposits of gold have caught the attention of geologists on the Island of Hispaniola. In the past four years, exploration and investigation of alluvial deposits have been initiated in both the Dominican Republic and Haiti. This type of activity is expected to continue over the next few years. Alluvial gold mining is rudimentary gold washing, done mostly by farmers. It is an old tradition, dating back at least 100 years, and is done by small, independent, or community farming villages in the mountains and plains of the Dominican Republic. Investigations in the DR Recently, alluvial gold investigations have been undertaken in well known locations of the Dominican Republic. One is in the Villa Altagracia area. Here, the terraces and gravels of the Haina River basin were examined, test-pitted, and assayed by Minera Altagracia, a local Dominican mining group. Results led to a new investigation by the state-owned Rosario Dominicana (RD), the company that mines the gold at Pueblo Viejo. Rosario tested areas previously investigated by Minera Altagracia. RD could not define the type of concentration that could justify an industrial-scale type of exploitation. The Haina River placers are located in the flats and valleys of Central Dominican Republic. They are classified as small-scale type of operations where local cooperatives can do the traditional gold washing. It is not now considered a dredgable project for a mining company. The next alluvial gold investigation was undertaken by the Dominican Department of Mines and others in an area of some 700 km2 (270 sq miles) in the northeast near Miches. Farmers have been washing gold in streams and excavating pits in various areas, particularly La Mina and have made a living. Government geologists panned several hundred streams and river tributaries. They also washed material from deep excavations. The results, however, were negative insofar as locating alluvial gold concentrations suitable for large-scale or industrial-scale exploitation. The most favorable locations were the terraces along the Jayán and Cuarón Rivers in the area of Miches. But the grade od concentration is poor. Actually, only traces of gold were found in these

Jan 8, 1986