Search Documents

The dynamic response of holdup in a continuous ball mill has a direct influence on the rate function of grinding kinetics and is useful for predicting the variation in the size distribution of the finished product with time.A model was proposed involving three interacting, completely mixed chambers and this was used to derive analytically the transfer function of the system, from which the unit impulse response and the unit step response of the holdup with feed rate were obtained.The theory was confirmed by comparing it with previously published experimental data for the residence time distribution of particles passing through a ball mill.

Jan 1, 1975

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By Darren Thorton, David Sprott, Ian Brunton

Blasting causes movement of the rock and can be detrimental to the accurate delineation of the ore and waste regions within the resulting muck pile. The consequences can be ore loss and dilution. However, ore loss and dilution can be minimized and significant increases in profit can be realized if the movement can be accurately measured. Various methods have been used to measure muck pile movement including poly-pipe, chain and sandbags but these have been either inaccurate or impractical. The Julius Kruttschnitt Mineral Research Centre, JKMRC, has developed an electronic blast movement monitor that provides accurate three-dimensional movement vectors following a production blast. From this information, the ore block boundaries in the blasted bench can be adjusted to compensate for the measured movement and then ore recovery can be optimised. Following initial development of the prototype technology, the JKMRC further developed and demonstrated the system in actual production blasts at an open pit gold mine operated by Placer Dome Inc.

Jan 1, 2005

By J. Sammarco

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to determine if light-emitting diode (LED) cap lamps can improve safety by reducing glare. Glare can impede a miner?s ability to see hazards and to safely perform their work. Another objective is to determine if a person?s age is a factor. This is important because the workforce is aging ? the average miner is now about 43 years old. Three cap lamps were used to evaluate glare: an incandescent cap lamp, a commercially available LED cap lamp and a NIOSH prototype LED cap lamp. Thirty NIOSH personnel from the Pittsburgh Research Laboratory (PRL) served as test subjects. Three age groups were established with ten subjects in each group. Testing was conducted in the Mine Illumination Laboratory (MIL) of NIOSH PRL. The results indicate no statistically significant difference in discomfort glare among the incandescent and LED cap lamps. However, an analysis of variance for disability glare indicates that the LED cap lamps were superior for the older subjects. Disability glare scores for the oldest subject group improved 53.8% when using the NIOSH prototype LED cap lamp compared to the incandescent cap lamp and 36.5% compared to the commercial LED cap lamp. It ap­pears that, given the conditions of this study, LED cap lamps will not increase discomfort glare and can enable significant improvements in disability glare for older workers. It is also evident that not all LEDs are created equal. The disability glare improved the best for older workers when they used the NIOSH prototype LED cap lamp, which has a different spectral power distribution (SPD) (more short wavelength energy) than the commercial LED cap lamp. Therefore, for disability glare, the results suggest that the SPD is an important factor to consider in cap lamp design.

Jan 1, 2009

By J. Girard-Dwyer, T. Camm

Direct costs such as medical, legal, administrative, and worker’s compensation costs, property damage, lost earnings, and lost benefits are typically used to compute the economic impacts of occupational injuries. However, there are also a number of less obvious, indirect costs that substantially contribute to the overall loss costs. In fact, for every $1 of direct costs an estimated $3 to $5 of indirect costs are also incurred. This paper presents a systems approach that incorporates engineering, economics, psychology, and sociology in order to evaluate the total value of investments in safety. By studying the interrelated system comprised of the injured worker, their family and coworkers, as well as the organizational structure that was the setting for the incident, a methodology can be developed that will more accurately capture the true costs of mine injuries.

By W. F. Netzeband

This paper, which describes mining methods and practices at the Rialto zinc-lead mine American Zinc, Lead & Smelting Co., in northeastern Oklahoma, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States, The Rialto mine is in the SE1/4 SW1/4 sec. 20 and the NW1/4 sec. 29, T. 29 N., R. 23 E., Ottawa County, Okla. (fig. 1). The 200-acre property is southwest of and adjacent to the town of Picher in the central part of the Picher field of the Tri-State zinc-lead mining district (fig. 2). Other mines of the company adjoin the Rialto on the east and south. Zinc-lead ores have been mined almost continuously from the Rialto tract since 1916. The property was acquired by American Zinc, Lead & Smelting Co. late in 1951, and the mine was operated thereafter by the Nellie B Division of that company until the end of 1955, when it was subleased to the Residue Mining Co.

Jan 1, 1958

"The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are:1. Line Drilling2. Cushion Blasting3. Smooth Wall Blasting4. Buffer Blasting5. Presplitting or Preshearing6. Air Deck Presplitting"

Jan 1, 1994

By Steve Colbum

LTl’s MapStar LPS (laser positioning system) utilize both tripod mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environment characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, interactive software program, which can be run on any standard PC. Win Prof, the Windows-based analytical software package is used to reduce the data for generating bench face profiles, surfaces, volumes, estimating true burdens and mining ratio calculations. In addition, the software has many other built-in routines to calculate powder factors, toe shear, to map structural contacts and to predict the flyrock potential based on the Burden to Energy ratios. An extensive, built-in library of explosive’s data facilitates these calculations. It will also conform automatically to user-specified minimum and/or maximum burden in relation to the explosive energy, hole diameter and bench geometry - for both vertical and inclined holes. Numerical data can be represented in 2D or 3D to emphasize the hole-burden-face relationships.In this workshop, the MapStar LPS instruments and Win Prof analytical software will be thoroughly demonstrated. Demonstrations include equipment configuration, typical field setups and several effective survey procedures, including processing of some sample data.

Jan 1, 2000

By Badiozamani Khosrow

Introduction The mining industry has been using computers since the late 1950s. Despite this early start, the use of mine planning software is not a common practice in many operations. But the trend might be changing because of the availability of relatively inexpensive personal computers (PC). The introduction of these machines has generated unprecedented interest by mine managers to computerize their planning operations. However, some managers have become disappointed with the PC's lack of adequate software and the inability to handle the massive amounts of information required for modeling. This paper is an attempt to shed some light on the future of computers in the mining industry. It will examine: • historical progress in the computer industry, • future advances in the computer industry, • historical usage of computers in mining, and • future alternatives available to mining. Historical Progress The computer industry has come a long way since the first full-fledged electronic digital computer Electronic Numerical Integrator And Calculator (ENIAC) was built in 1946. This machine weighed more than 27 t (30 st). It contained 19,000 vacuum tubes, occupied 139 m2 (1500 sq ft), and could perform 5000 additions per second. By contrast, today's fastest, commercially available computer is the CRAY-X. It weighs less than 5 t (6 st), has no vacuum tubes, occupies less than 9 m2 (100 sq ft), and performs over 100 million operations per second. This is an incredible advancement in less than 40 years. One person commented on the rate of advancement in the computer industry. He suggested that if the auto industry had advanced at the same rate as the electronics industry, we could buy a Rolls Royce for $2.75 and it would run

Jan 9, 1984

By Carlos F. Perucca, Maria Virginia Ramírez A.

"Chile based SQM S.A., exploits potassium chloride rich salts at the Salar de Atacama, in northern Chile. The process includes the solar evaporation of natural brines existing in the Salar salt bed, followed by conventional flotation to recover Muriate of Potash (MOP) for fertilizer use.This paper describes a structured method developed to aid in understanding the metallurgical response of the solar evaporated salts to conventional flotation. The method uses classical metallurgical data analysis combined with laboratory and plant-scale testing, and rudimentary mineralogical studies.As a result of the study, several changes were made to the flotation circuit which produced an operation that is much more consistent and easier to control, and has an increased recovery. An optimized circuit, currently being financially evaluated, has also been conceptually designed based on the findings of this work.INTRODUCTIONSQM S.A. is the world’s largest producer and distributor of specialty fertilizers, iodine, lithium, as well as a wide array of industrial and specialty chemicals. SQM is a public corporation whose shares are traded in the Santiago and the New York Stock Exchanges.SQM S.A. exploits the mineral rights at the Salar de Atacama in northern Chile. Its production processes involve the solar evaporation of natural brines existing in the Salar salt bed, aimed at the recovery of Potassium, Lithium and Boron compounds."

Jan 1, 2004

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. loader. These instructions are based upon two actual install .at ions: one made in a mine on loader, model 14BU10-11AH, and one in the factory on model 14BU10- 11AH. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other loaders with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other loaders and can determine any necessary modifications if they are not.

Jan 1, 1973

By Paul D. Tomlingson

Editor's note: This is the first of two articles on maintenance. Part two, "Effective maintenance downsizing techniques," will appear in the October issue of MINING ENGINEERING. Most mine managers are aware that the cost of maintenance rarely goes down unless work is done less often and with fewer people. Fewer people translates into downsizing and seldom means making maintenance more efficient. Even so, mines that have struggled unsuccessfully to improve maintenance and are now pressed to reduce maintenance costs may opt for downsizing. On the other hand, mines with an immediate need to reduce costs may be forced to downsize because they cannot wait for needed improvements to take effect. This can be bad news for maintenance. In any case, the mine must downsize correctly to ensure effective maintenance is sustained.

Jan 1, 1994

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

By A. N. Holden, W. E. Seymour

DURING the last several years, the U-Zr system has been studied at many laboratories as one of the research programs sponsored by the Atomic Energy Commission. The equilibria in part of this system have been difficult to determine, although the phase diagram from 0 to 60 atomic pct Zr has been established with reasonable certainty. Existing diagrams of the system vary appreciably beyond 60 atomic pct Zr, particularly with regard to the existence of an intermediate phase. Most existing diagrams show a transformation or reaction horizontal near 600°C. In 1955, a collection of uranium phase diagrams' was prepared at the Battelle Memorial Institute and the U-Zr diagram in that collection contained a questionable region in the vicinity of 60 to 80 atomic pct Zr. Summer-Smith" has published a phase diagram of the system that shows no intermediate phase. Summer-Smith did his work with powders and found only the uranium and zirconium eutectoid mixture from X-ray patterns of material annealed below 600°C. Mueller3 at Argonne National Laboratory did similar work with filings, and he found that initially there was a pattern of an intermediate phase, but on long-time annealing

Jan 1, 1957

By José Díaz Barrios

El proceso de la explotación minera de la veta Oroya Techo, perteneciente a la mina Casapalca, ha generado un desequilibrio del macizo rocoso, donde la energía que la roca de la caja, piso y techo (volcánicos de la formación Carlos Francisco) no pueden soportar mas allá del límite de su resistencia y deformabilidad natural, es liberada o “compensada” con el estrujamiento plástico de la veta Oroya Techo (estructura carbonatada). En ese sentido, el presente texto describe una manera de cuantificar dicha deformación a través del monitoreo de convergencias, donde se emplea un simple extensómetro de cinta manual y asímediante una análisis estadístico, seleccionar estaciones de convergencia por rangos de mediciones.

Sep 12, 2005

By Panagiota Tsolis-Katagas, Basilios Tsikouras, Tassos A. Grammatikopoulos, C. Katagas

"Mineralogical techniques including microscopic methods, reflected and transmitted light microscopy, Cathodoluminescence (CL) and Scanning Electron Microscopy equipped with an Energy Dispersive Spectrometer (SEM-EDS), are useful in determining the quality of industrial minerals. They are essential for studying ores and metallurgical products including the evaluation of physical characteristics of the mineral, paragenetic relationships, associations with possible deleterious contaminants (e.g., sulphides), spatial distribution within the ore zones and liberation characteristics. The methods are inexpensive, and provide quick identification and distinction among the industrial minerals and the gangue minerals in a section. Additionally, SEM is necessary to reveal complex textural sequences and 3-D measurements of minerals and quick semi-quantitative analysis.Common analytical methods include Electron Microprobe Analyses (EMPA) and Whole Rock Analysis (WRA) (commonly with XRF and ICP) for major and trace elements. The EMPA analyses of industrial minerals provide information on the purity of the analyzed grains as opposed to the bulk chemical analyses that may be misleading due to contamination by other associated common “gangue” minerals. These techniques have been implemented for the case studies of wollastonite, V-magnetite and muscovite. Therefore, these methods can provide extremely useful information and lead to the implementation of a successful pilot-testing programme.MINERALOGICAL EVALUATION OF DEPOSITSDespite their considerable and increasing economic importance, industrial mineral deposits have traditionally been neglected by economic geologists, and are only rarely the subject of the detailed analysis widely lavished on metallic mineralization. Moreover, in that they generally represent concentrations of “normal” rock-forming minerals, albeit commonly with particular textural and/or geochemical features, they have tended to fall between the mainstream of petrogenetic studies and mineral deposit research (Grammatikopoulos 1999). For many industrial minerals, little attention has been paid to the factors responsible for their local concentration as large and high-grade bodies. This comparative neglect has particularly been the case for minerals such as talc and wollastonite, widespread in metamorphic rocks, in which they are reasonably interpreted as components of assemblages derived, respectively, from pelitic sediments, ultramafic igneous rocks and siliceous limestones."

Jan 1, 2003

By A. V. Shroff

The Indian Standards code of practice for design and construction of underreamed piles contains provision for installing such piles in expasive soils. In recent years, a large amount of research work has been carried out in the analysis, design, construction and performance of underreamed piles in expansive soils. This paper suggests that the results of this research field tests should be included in the code. Various additions and modifications as well as deletions that should be incorporated in the code are discussed.

Jan 1, 1996

By R. Sullivan, K. Joiner, B. Emery, M. de Vries, F. A. Stober, L. R. Nelson, J. M. A. Geldenhuis

Keywords: Pyrometallurgy, smelting, converting, furnace design, furnace retrofit, high-intensity smelting, copper coolers, plate coolers, waffle coolers, tap-blocks, lower sidewall air-cooling, wall hold-down system, platinum group metals, ferroalloys, ferrochrome, ferrocobalt, ilmenite smelting, ironmaking, operational readiness, operational support The paper describes the development of furnace designs by Hatch in conjunction with the smelting plants in Africa to meet the intense process requirements in certain applications; continued improvement in operating efficiency through increased throughput from existing crucibles; and improvement in campaign life and furnace integrity. The era of Hatch in Africa has seen the doubling of furnace power in retrofit projects using existing crucibles to developing the highest intensity immersed electrode operations in the world. This has resulted in minimized OPEX and CAPEX per unit of production. Through the continued development of its cooling, binding and furnace power supply technologies and working with the experienced and knowledgeable personnel at the smelting facilities in Africa, Hatch has managed to meet the challenges of ever increasing furnace process requirements associated with increased power density and superheats prevalent in the operations. In addition to developing furnace crucible designs, Hatch has also intensified its ?after sales service and support? with the construction, commissioning and start-up technical assistance and operational readiness and operational support for ramp-up to nameplate capacity and beyond. The key areas of furnace risk associated with high superheat molten material tapping has also seen the development of diagnostic systems to mitigate risks and produce early warning signals for the operators.

Jan 1, 2006

By H Peiming, W Sakurai, Y Matsuhisa, H Shimazaki, Y Fukahori

Oxygen and carbon isotope mapping of hydrothermally altered wall rocks was applied to the blind ore prospecting of skarn Pb-Zn deposits in the Kamioka mining district, centralJapan, where the wall rocks consist of heterogeneous rock units. The results (d18OSMOW of -1.1 to +17.3ë and d13CPDB of -5.0 to +4.8ë for limestones, and d18OSMOW of -0.8 to +12.5ë for silicate rocks) show isotope zonations of the wall rocks with depletions in heavy isotopes (18O and 13C) toward the centre of mineralization. The isotope zonations likely formed by interaction of migrating thermal waters with the wall rocks during the mineralisation. The heavy-isotope depleted zone, which indicates higher temperature or higher water-to-rock ratio of the system, occurs in the footwall of a fault, indicating that the fault played the role of main conduit of the ore-forming fluids. A heavy-isotope depleted zone was also found in an area, where significant mineralisation had yet to be identified. Recent drilling in this area has intercepted a zone with a grade of 16.0% Zn, 0.8% Pb, and 35g Ag per metric tonne at a depth of about 360 m.

Jan 1, 1995