Search Documents

Detailed characteristics of gold from Pliocene auriferous quartz gravels from Waimumu (Southland) have been studied using a combination of optical microscopy, energy dispersive microprobe analysis and scanning electron microscopy techniques. The gold at Waimumu is classified as either: 1. detrital gold, or 2. irregular gold. A number of different morphologies a recognisable within each 'gold type'. Evidence is given for an predominently authigenic origin for some of the gold at Waimumu.

Jan 1, 1987

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973

By R N. Robson, A B. Christie, I J. Graham

Strategy development by the minerals industry identified the fragmented management of mineral resources as a significant impediment to the discovery and development of New Zealand Æs mineral resources. The total gross value of New Zealand Æs potential resources of coal and minerals is estimated at about $400 billion, but their potential value is not being realised. The management of minerals is now largely under the control of 86 local authorities (regional and district councils) and the lack of recognition of the significance of the sector has lead to inconsistencies in the way minerals are managed. The industry strategy influenced science funding for minerals, with the result that the 'mineral wealth' component now includes research on making better use of resource data in minerals management. Initially this research has targeted Otago and Northland regions where a number of initiatives are now in progress.   In Otago the Regional Council has budgeted to contribute $1 million towards a regional geophysical survey to advance mineral exploration and the management of subsurface resources in the region, to work cooperatively towards improving public awareness of the significance of minerals to regional economic activity, and to better coordinate policy-making for minerals at regional and district levels.   Crown Minerals, and the Far North and Whangarei district councils are considering providing funding support for an economic study of the mineral potential of Northland, building on a mineral resource assessment undertaken by GNS Science. Enterprise Northland is adding minerals to their list of potential growth sectors, and is supporting the operation of a Northland region minerals focus group.   Regional development agencies and local authorities have shown that they are willing to include mineral resources in their development strategies and to provide for them in policies and plans when supplied with information and assisted with technical support.

Jan 1, 2006

By S G. Keyte

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.l mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass Yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80 per cent and mass yields of less than one per cent can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

By H. Maleki

In this paper, long-term measurements in five underground mines are presented to demonstrate how these measurements can be applied to stability evaluations and design of underground excavations. These case studies address both the global aspects of strata response to mining activities as well local ground behavior and support loading. The measurements include static (stress and deformation) and geophysical. Case studies quantify pillar behavior, roof-floor deformation patterns, overburden response, and microseismic activities. Large-scale studies quantify the nonuniform nature of overburden deformation and collapse. Local measurements address yield and stable pillar load deformation characteristics, as well as the performance of support systems under combined axial and lateral loads.

Jan 1, 2002

By S Hall

Mining schools around the world, many unfortunately now closed, were often established to teach the techniques of narrow vein mining and associated processing to students studying part-time while working in the industry. This arrangement ensured graduates (or æassociatesÆ) had a mix of skills and knowledge invaluable to the industry.It is argued that there is still a need to educate students in these narrow vein techniques and that there will be a growing demand for such graduates with a high level appreciation of this type of mining. There is also a need for innovation in narrow vein mining and processing to develop specific technologies and allow the use of techniques applied in æbulk miningÆ to achieve improvements in productivity, safety and economic performance.This paper aims to review the situation with regard to education and innovation in narrow vein mining.CITATION:Hall, S, 2012. Narrow vein education - back to the future?, in Proceedings Narrow Vein Mining 2012 , pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

COALTECH 2020 initiated a research project to provide the coal mining industry with a modelling tool to determine the expected types of subsidence, risks and the investment required in post-closure funds to cater for subsidence associated with bord and pillar mines. A detailed literature review was conducted to determine the most important parameters in calculating the cost associated with surface subsidence. A subsidence prediction model was developed to determine the likelihood of different types of subsidence. The study made use of current knowledge of failure mechanisms and its aim is to assist the industry and government in arriving at the most suitable arrangements when authorities require financial instruments to assure compliance with environmental regulations.

Jan 1, 2003

By E. R. Spencer

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

Jan 1, 2008

By G D. Price

Scheelite mineralisation east of the main divide in' the Southern Alps of New Zealand was originally identified by Royden Thompson who is now a geologist with the NZ Geological Survey. This mineralisation was brought to the attention of CRA in 1978. Reconnaissance surveys were carried out in 1979 to delineate the extent of the mineralisation. This was undertaken using ultraviolet light examination of the sediments within the major drainages in the Southern Alps. This defined tentative zones of prospective mineralisation. As a result of this, preliminary reconnaissance, exploration licences were applied for -those areas in which indications of scheelite mineralisation were strongest. A total of 1737 km2 of ground was applied for within four exploration licences. These covered the main Southern Alps mountain chain between the Haast/Wanaka highway and the Mt Cook National Park.

Jan 1, 1983

By Felix Cheng

Extensions to the Convention Centre in Adelaide, South Australia consisted in part of construction over the existing railway system comprising nine rail lines and passenger platforms. Vibro-pile (Aust) won the design and construct tender with a solution comprising over 500 cast insitu concrete piles. The pile types were 500 to 900mm diameter non-displacement CFA piles and 400mm diameter displacement V-piles. The V-pile is a cast insitu screw pile developed by Vibropile (Aust) Pty Ltd. Both pile types were installed with minimal noise and vibration required for the project, while the displacement V-pile had the advantage over the CFA pile by developing the same pile capacity but with a smaller diameter and with minimal spoil. The latter was important in alleviating spoil removal problems near the railway tracks and disposal of potentially contaminated spoil. The results of dynamic compression load testing and static lateral load testing indicated that the performance of a 400 mm V-pile was equivalent to a 500 mm CFA for this site. The lateral load testing indicated that the surficial soils have a major influence on the load-deflection response, but despite the site containing up to 4 m of filled ground, the piles were found to carry the required lateral loads satisfactorily.

Jan 1, 2002

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By L. B. Hales

Image analysis for feed belts and flotation has been used for over 20 years. It has been shown to aid in the modelling and optimization of Sag Mill circuits, and any improvements in the image analysis result in improvements in the model for control. Using a laser to measure the height-profile of rocks on the conveyor has been shown to increase the accuracy of the size classification. We have developed a system using two cameras in a stereoscopic configuration to provide height-profile measurement without the added expense and safety concerns of using a laser. Additionally, we have developed a novel technique for calibration of the system, using artificial intelligence techniques to optimize the model fit by adjusting the image analysis tuning parameters to values resulting in the best classification.

Feb 27, 2013

By M. J. Beus, B. Stewart, S. Iverson

Ore-pass hazards are a significant safety problem in US underground metal mines. From 1975 to 1995, nearly 75% of injuries during pulling or freeing of ore-pass chutes were related to falls of broken rock or the use of hand tools. Risk assessment methods are being used to identify the most probable causes of ore-pass failures and analyse the factors that result in malfunctioning or safety reduction. Static and dynamic loads are being measured in the laboratory and by field testing, with data from test ore passes compared with mine data to characterise true system behaviour. Computer modelling using closed-form solutions, finite element analysis and a newly developed particle flow code are being use to predict loads from ore and waste flow and impact. Preliminary results indicate that dynamic impacts may be much less than expected, as a result of damping factors, normal and shear stiffness and mass frictional characteristics

Jun 19, 1905

By H. Y. Sohn, Hang Goo Kim

Computer simulations were carried out using calcium ferrite slags containing 25 wt% CaO, and the results compared with those obtained using fayalite slags. There was little difference in overall elimination of Pb and Bi, but elimination of Sb and As was much lower with calcium ferrite slag. When calcium ferrite slag is used only in the converting stage and fayalite slag in the smelting stage, as in the Mitsubishi process, the contents of Sb and As in the blister copper can be kept to reasonable levels. This allows advantage to be taken of the considerably higher iron oxide-holding capacity of calcium ferrite slag than of fayalite slag at the high oxygen potential under converting conditions, thus preventing precipitation of magnetite. Satisfactory agreement was obtained between predicted values and observed data from a Mitsubishi converter

Jun 18, 1905

A shortage of technical skills in all areas of the mining industry is being experienced worldwide. This has significant consequences for design, operations, productivity and safety and, therefore, needs to be seriously addressed, both in the short and longer term. It is therefore both a strategic and a tactical issue. Importantly, however, since mining is a long-term business, the shortage of skills must be dealt with from a strategic point of view to ensure the supply of the necessary skills for future mining. This paper will deal specifically with the provision of high level technical skills, that is, university graduates in mining engineering, and the outlook for the institutions that are currently producing such graduates.

Jan 1, 2008

By Víctor Cárdenas

El presente trabajo describe el manejo de las herramientas de calidad que aportan a la reducción de riesgos en la compañía minera La Poderosa. Para determinar los defectos, causas y consecuencias, es necesario conocer el procedimiento de control de los mismos a través del diagrama de Ishikawa o el ciclo de PHVA. Esta metodología permite encontrar la solución a los problemas dentro del aseguramiento de la calidad, seguridad y productividad de una empresa, así como establece la fuente de la causa de los accidentes por lesiones, como de los daños a la propiedad privada. En consecuencia, su aplicación se ha estandarizado en las áreas de seguridad y medio ambiente de dicha minera desde hace dos años, obteniendo resultados muy satisfactorios como el Premio Nacional de Seguridad en minería subterránea otorgado por el ISEM.

Sep 13, 2001

By R F. Hoeberling

"The use of ground penetrating radar (GPR) for geological purposes has been underway for almost two decades. The commercial need for a versatile GPR that can rapidly identify buried objects andunderground voids has been recognized and is an area of research that has already proved useful for several geological activities. Several types of GPR endeavors have been reported in the literature, including exploration of placer deposits (Davis, et al. 1985) and heavy metals (Hammond and Sprenke, 1991), improving oil recovery (Witterholt and Kretzschmar, 1984), investigating coal seams (Coon, et al., 1981), stratigraphic survey (Fisher, et al. 1992), Lunar soils characterization (Olhoeft, et al. 1975 and Strangway, et al. 1977), characterization of rock around mine tunnels (Cook, 1985), location of old mine workings (Scaife, et al., 1992), location of abandoned gas wells in coal seams (Kemerait, 1992) and survey of hazardous waste burial areas (Horton, et al., 1981). Coal seammapping has been developed using a related continuous wave, phase discrimination technique (Stolarczyk, 1990). As the technology for the radar equipment and the onsite computational power has increased, many new applications have become feasible. This article will describe the present status of the GPR technology and indicate some of the exciting possibilities for nearterm prototypes now being constructed."

Jan 1, 1994

By Detnet Solutions

1. “Daisy-Chain” concept The term “daisy-chain” stems from the fact that when the HotShot? detonators are connected there is a chain or electrical path for electrical current to flow from detonator A to detonator B, detonator B to detonator C etc until the path is terminated by an electrical means. The “daisy-chain” concept has long been used in electronic detonator systems, historically used in Expert Explosives’ ExEx 1000 5/6 wire system and currently in use in African Explosives Limited (AEL’s) Electrodet? electronic detonator system and has been adopted as the basis upon which the “auto-programmability” of the HotShot? electronic detonator system functions. HotShot? Detonators are connected to each other in a string, completing a “daisy chain”, and during the auto-detection mode of the control equipment, it is possible for the equipment to determine the order of hookup of the detonators as well as map the entire blast layout. The auxiliary components (Row Controllers & Branch Controllers) assist the control equipment in mapping the entire blast by indicating different points on the blast, i.e. The inflection point of a row of blast holes on a closed chevron timing pattern, the beginning of row of blast holes on open chevron timing pattern and extra blast holes or extra blast rows.

Jan 1, 2004

By Bethany Witter, Dyno Nobel

In the past decades, a technological explosion has caused generational shifts. First, millennials experienced a technological shift to computers and cellphones. Next, Generation Z experienced a shift to smart phones and social media. These two generations are immersed in technology and are accustomed to constant connectivity. How do the extractive and construction industries gain the interest of younger generations and integrate them into the industry?

Feb 1, 2020

By M. Zanotto

[ ] A period of heavy rains caused the river Adda to flood parts of the Valtellina, one of the Alpine valleys of Northern Italy. The exceptionally high waters put under considerable strain the whole system of embankments and levees controlling the river and protecting the adjacent towns and lands. In some places the water breached and washed away the embankments, submerging large tracts of cultivated land, buildings, roads and railway tracks. The town of Talamona, in the lower Valtellina, was hit particularly hard: in its proximity the river overrun and then washed away 300 m (1,000 ft) of embankment (see vicinity map, fig. 2), depositing large amounts of riverbed debris onto over 400 hectares (1,000 acres) of fertile land.

Jan 1, 1992