Search Documents

By Hojat Naderi

In this research assisted leaching of chalcopyrite using sodium peroxodisulfate was studied. Electrochemical techniques such as Tafel analysis and electrochemical impedance spectroscopy (EIS) were used to investigate the surface reactions of a chalcopyrite electrode in the presence and absence of Na2S2O8. According to the results, addition of sodium peroxodisulfate increases the current exchange of the corrosion process and prevents the formation of a passive layer on the surface of the electrode. EIS tests show the trans-passive dissolution of the passive layer on the chalcopyrite electrode in presence of Na2S2O8. Equivalent electrochemical circuits were modeled for Na2S2O8-free and -containing solutions and the model parameters were compared to determine the effect of S2O8 2− on chalcopyrite dissolution. Copper dissolution from pure chalcopyrite mineral and chalcopyrite concentrate was carried out using 15 g/L sulfuric acid solution with and without Na2S2O8. Simultaneous presence of 10 g/L ferric ion and 40 g/L peroxodisulfate salt results in about 40 and 18% of Cu extraction from chalcopyrite concentrate and pure chalcopyrite mineral, after 96 h, respectively.

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly. subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fumeless fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By Jean P. Murray

The extractive metallurgical industry is a major consumer of high-temperature process heat. It is, consequently, a major contributor of C02 emissions and other greenhouse gases derived from the combustion of fossil fuels for heat and electricity generation, or from the process itself. These emissions can be substantially reduced by replacing fossil fuels with solar energy as the source of process heat. Concentrated solar radiation can supply a large amount of thermal energy to endothermic reactions at temperatures exceeding 2000 K. Another potential for C02 emission reduction exists as well. Thermodynamically, the total amount of energy required for metal production at any given temperature is the enthalpy change of the reaction, AH. Of this total, an amount equal to the Gibbs free energy AG must be supplied as high quality energy in the form of electrical work or by using a reducing agent. Many conventional metallurgical electrolytic processes and reducing furnaces are unable to add only the thermodynamically required electricaVchemical energy due to process inefficiencies. Electrical work in excess of AG for the reaction may be used to supply process heat, or excess chemical reducing agent burned to supply process heat. Besides the thermodynamic and economic drawback, this inefficiency results in excess C02 emissions derived from the combustion of fossil fuels. With these practices, energy becomes an important cost element of the metal produced. Highly-concentrated solar energy has the demonstrated potential to separate these two forms of process energies, allowing the addition of only the thermodynamically required high-quality energy while high-temperature solar process heat is provided to the reactor. Examples of metal oxide reduction processes that have been studied experimentally in solar furnaces include the production of Fe, Al, AI/Si alloy, Mg, Zn, Tic, Sic, CaC2, TIN, Si3N4, and AIN by carbothermic reduction of their oxides, and the high-temperature solar- electrothermal reduction of ZnO.

Jan 1, 1999

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450°C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By Tibor Zoltai

Asbestos is a generic term for industrially useful fibers recovered from exploitable deposits of the asbestiform varieties of five silicate minerals: chrysotile, anthophyllite, actinolite-tremolite, cummingtonite-grunerite, and riebeckite. Asbestos and asbestiformm fibers of some other minerals are known to be carcinogenic. Minerals crystallized in the asbestiform habit are characterized by unique properties (morphology, strength and flexibility, physical and chemical durability, and defect-free surface structures). The key to the unusual properties, and health effects, of asbestifarm fibers appears to be in their unusual surface structure. In contrast, non-asbestiform crystals of the same minerals, including the five so-called asbestos minerals do not have these properties and are not carcinogenic (1, 2).

Jan 1, 1989

By G. B. Harris

Jaguar Nickel Inc. is developing the Sechol Nickel-Cobalt Laterite Project in Guatemala, Central America. Recognizing the potential advantages offered by chloride brine chemistry, Jaguar, at the facilities of Process Research ORTECH Inc, Mississauga, has developed an Atmospheric Chloride Leaching Process using a mixed chloride lixiviant to recover the nickel and cobalt, whilst leaving the majority of the iron and magnesium in the leach residue. Subsequent solution purification and mixed nickel/cobalt hydroxide product recovery is by standard precipitation methods, using recycled caustic magnesia, with a final stage of pyrohydrolysis of a portion of the concentrated magnesium chloride brine for recycling both the caustic magnesia and chloride lixiviant. The flowsheet that has been developed also offers opportunities for by-product recovery and efficient, environmentally clean process effluent management. The paper discusses some of the early leaching results in the context of strong chloride brine chemistry, with emphasis on how the controlling of water activity, hydrogen ion activity and chloride concentration permits the selective leaching of nickel and cobalt from an iron-magnesium matrix. Keywords: nickel, cobalt, iron, magnesium, Sechol, Guatemala, chloride, pyrohydrolysis

Jan 1, 2004

By Zhou Jun

Water-quenched samples were taken from a commercial flash furnace at three levels along its reaction shaft during operation at high feed rate. The samples were subjected to a series of analysis and observation. Such processes of the feed in reaction shaft as oxidation, desulfurization, melting, slag and matte formation and etc., variations of particle size along axial and radical direction of the shaft are investigated. The following smelting mechanism in reaction shaft named as “Multi-particle and multi-phase fusion model” is proposed: (1) Fragmentation and collision of concentrate particles take place simultaneously in reaction shaft with particle size growing up. Collision produces large-size “unit melt” which falls into the reaction layer in the settler bath. (2) In the settler reaction layer below the shaft, weak bath smelting reactions take place among the shaft products, producing final matte and slag which separate into two layers. (3) The processes in the shaft are all progressive along the whole height of the shaft. The predominant reaction in the shaft is oxidation, not reduction.

By Hideki Minoura

"Two novel electrochemical techniques for the preparation of highly crystallized CdS film have been presented. One is cathodization of a conductive substrate in an acidic chemical bath containing cadmium salt and thioacetamide, where electroreduction of proton at small current densities induces a growth of highly crystallized CdS thin films, whose growth is not disturbed by the reactions in the solution phase. The other technique is electoreduction of aqueous Cd2+— SCN complex. An advantage of this technique lies in no formation of solid particles in the bulk, of the bath.IntroductionIn recent years much attention has been paid to materials preparation by solution processing because of its advantages in lowering the cost as well as the stress to the environment, as compared to the conventional gas phase techniques which unavoidably require high temperature and/or vacuum. We have been trying to explore novel techniques for preparing functionalized compound semiconductors by aqueous solution process. Semiconductors which we have been mainly focusing on are CdS and ZnO, which are important semiconductors finding applications in various devices. In the present paper, some of the techniques that we have recently established for the preparation of highly crystallized CdS will be presented.Methods of the CdS film processing in solution phase (wet process), which have been reported so far can be divided into two major groups; one is chemical bath deposition (CBD) in alkaline solution containing Cd2+ and thiourea 1)4) and the other is electrodeposition (ED) in acidic solution containing Cd2+ and thiosulfate ions - 5)-8) or organic solutions containing dissolved sulfur 9)-11)."

Jan 1, 2000

By Richard A. Shulkosky

The American Iron and Steel Institute (AlSO, in conjunction with the U.S. Department of Energy (DOE) jointly funded the development of a mechanical properties model for Hot Strip Mills. INTEG process group, inc. validated an enhanced version of the model under a project funded by the AlSI/DOE Technology Roadmap Program (fRP). The Hot Strip Mill Model (HSMM) version 6.0 allows users to easily set-up their mill configuration, simulate a rolling mill schedule and calibrate the model for a variety of grades of steel. Starting from reheat furnace drop out, the model simulates roughing mill stands (reversing and continuous), heat retention equipment (coil box and covers), finishing mill stands (tandem and Steckel mills), the run out table and the mill exit area. The HSMM uses a series of physical models to calculate both the thermo-mechanical and the microstructure evolution of steel being processed in a hot mill to predict its final mechanical properties. The enhanced HSMM was validated using a multitude of samples from several steel companies. Excellent agreement was obtained for tensile strength. The supporting steel companies have utilized the model for a variety of practical applications. Keywords: Process Modeling, Microstructure Evolution, Mechanical Properties

Jan 1, 2003

By Derek J. Fray

"A need exists for fast and accurate analysis of species in various phases at elevated temperatures. Although modern analytical techniques are very efficient, the equipment is usually situated some distance from the industrial operation and time is spent taking the sample and sending it to the analytical facility. Several minutes can easily lapse and, during this time, heat must be supplied in order to keep the system molten and, if the composition is changing rapidly due to a refining process or reaction with the environment, the information may only be of retrospective use. Perhaps more important reasons for the use of on-line sensors are that instantaneous analysis gives better control, process optimisation and the minimisation of energy losses and pollution. To date oxygen has been the only element which is measured widely using solid electrolytes. However, the analysis of many more elements is required and possible electrolytes for other species are discussed. For some elements, ~here is no suitable conducting electrolyte and, therefore, a different approach is adopted where the electrolyte, in which one species is mobile, comes to equilibrium with another species. IntroductionThere is an ever increasing demand for the development of sensors for on-line measurements in most areas of technology and, in particular, metal processing. This is especially relevant in situations where greater control can be achieved by monitoring the chemical composition of the melt during processing and where a minor constituent in the melt can have a major effect on the properties of the finished alloy. Although modern analytical techniques are fast and reliable, the equipment due to its complexity, is frequently situated away from the process area and valuable time may be spent in sampling and transportation. During this period, heat may have to be supplied to prevent solidification and the refining reactions may be continuing, and, therefore, the analytical information may not be of direct use."

Jan 1, 1988

By L. M. Luckevich

Gypsum is a product from the neutralization of sulfuric acid by lime or limestone. This paper will discuss specifications for gypsum used in wallboard, cement and agriculture and the factors affecting its utilization potential. Process conditions during the neutralization which enhance or inhibit utilization potential will be included. In addition, this paper provides a technical and economic perspective of the gypsum industry in North America with a view to the factors affecting the utilization of synthetic gypsum in traditional applications. Current production and consumption of natural and synthetic gypsum in Nonh America are described and the impact of their differences on utilization options are discussed.

Jan 1, 1996

By Alan M. Russell

In recent years, several rare earth intermetallic compounds with the B2-type structure have been reported to exhibit high tensile ductility and high KIC fracture toughness at room temperature. These materials retain considerable ductility even at 77K. These are noteworthy findings because most intermetallics possess poor room temperature ductility and low fracture toughness unless one or more special contrivances are applied (e.g., doping with small additions of interstitial elements, offstoichiometric compositions, testing in ultra-dry atmospheres, etc.). This paper summarizes recent findings on rare earth B2 intermetallics. These include the determination of the active slip systems; the strain rate sensitivities; yield strength maxima at elevated temperatures; the search for possible twinning and stress-induced phase transformations; ab initio calculations of their defect energies and the anisotropy of dislocation line tension. Potential applications of these materials and the possibilities that this study may suggest strategies for increasing ductility in other intermetallic compounds are discussed.

Jan 1, 2008

By C. S. Ek

Tests have been performed to recover silver and lead from residues produced after a super-hot leaching in a zinc hydrometallurgical plant operating with jarosite precipitation. When this residue is leached in ammoniaammonium sulfate or in diethylenetriamine solutions, lead dissolution is not complete and its recovery from the aqueous solutions is either difficult, due to the operating conditions, either expensive due to the amount of added reagents. In both cases, silver is partly dissolved, partly left in a new residue still containing lead and baryum sulfates. The best treatment seems to include a selective flotation producing first a silver concentrate assaying about I % Ag, then a 50 % lead concentrate collecting the baryum salts, and a final quartz-gypsum tailing. Metal recoveries can reach 50 % and 80 %, respectively.

Jan 1, 1989

By Yuanbo Zhang, Bin Xu, Guanghui Li, Xiao Kang, Chen Liu, Tao Jiang

Iron-bearing dusts, containing valuable constituents such as Fe, CaO, MgO, C, etc., are generally utilized as raw material in iron ore sintering. However, the dusts characterized by low granulating and refractory performances always lead to negative effects on sintering indexes. As we know, the innovative process named composite agglomeration process (CAP) has a series of advantages compared to traditional sintering process (TSP). In CAP, part or all of the iron-bearing dusts is made into green pellets with 5-15mm in diameter, while the rest of iron-bearing dusts and all of the other fine ores is granulated after mixing with fuels, fluxes and return fines. Compared with TSP, CAP could increase the ratio of iron-bearing dusts from 5% to over 20%. Meanwhile, the yield, ISO tumbler index and productivity reached 75.82%, 65.13% and 1.531t·m-2·h -1, respectively.

Jan 1, 2015

By S. M. Hay

The zinc content of blast furnace and basic oxygen furnace dusts is low compared with electric arc furnace dusts and it is generally not economical to treat the dusts to recover zinc. However, they have a high iron content and removal of the zinc would allow recovery of the iron values. A literature review and thermodynamic analysis was undertaken and, as a result, several smelting options were identified. This paper describes experiments undertaken to develop understanding of metallurgical aspects of these processes which are not amenable to theoretical analysis. Dusts from an Australian steelworks were characterised in order to determine their mineralogical make-up and the form of the iron. The processing aspects investigated in the laboratory were slag-metal equilibrium and solid-state pre-reduction using reducing gases of compositions expected from bath-smelting processes. Particular attention. was paid to the deportment of zinc, sodium, potassium, phosphorous and sulfur between the phases formed during smelting and pre-reduction. The smelting results indicate that less than 10% of the zinc, sulphur, sodium and potassium report to the metal. About 99% of the zinc and potassium and about 80% of the sodium could be volatilised from the dusts by reducing them at 1,000°C with mixtures of CO, CO2, H2 and H2O even when metallic iron was not formed. The experiments indicate that smelting of blast furnace and basic oxygen furnace dusts should produce hot-metal of a composition which can be blended into the main stream of hot-metal in the steelworks.

Jan 1, 1994

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Pravas Ranjan Behera

Red mud of Indian origin contains around 55% plus of Fe2O3 and is considered as a hazardous waste for the alumina industry. For production of one tone of alumina employing the Bayer’s Process, around two tones of red mud is generated from three tones of Bauxite. Conventional process of steel making is not devoid of environmental pollution. In the present investigation, efforts have been made to produce steel from red mud by adopting reduction roasting, magnetic separation and hydrogen plasma smelting route. Magnetic fraction, containing enriched iron oxide and minimal content of alumina, is produced following the first two stages which is then subjected to hydrogen plasma smelting process for production of steel. This novel concept follows a green path way for production of steel free from pollution and is termed as green steel. Further, the only by-product that is produced in the process, is water, which is eco-friendly and recyclable.

Jan 1, 2015

By C. P. Broadbent

The process metallurgy of many nickel laterite smelting operations is controlled largely by the physical chemistry of the slag system. Consequently, accurate phase diagram information and physicochemical property data are essential to interpret and predict the behaviour and optimisation of the overall process. The system (SiO2 - MgO - FeO) first described by Bowen et al. between 1914 and 1935 and the system (SiO2 - MgO - FeO - Fe2O3) determined by Muan and Osborne in 1956 are of particular relevance to the study of nickel laterite smelting slags as these systems form a reasonable approximation of many industrial slags. This paper will review the literature for these (and other relevant) phase systems. In addition data available from the ternary and (quasi)ternary phase diagrams will be compared with data obtained from industrial slags. The physico-chemical properties under consideration will include; melting and crystallisation behaviour (solidus and liquidus temperatures), viscosity - temperature relationships, heat flux considerations, electrical conductivity, surface and interfacial tension.

Jan 1, 1993

By Dandan Jian, Christian Karcher

Information of liquid steel flow patterns inside the mold may be obtained from the velocity at the free surface (meniscus). This meniscus flow may be measured using the contactless electromagnetic technique termed Lorentz force velocimetry (LFV). It is based on the measurement of Lorentz forces acting on a magnet system when an electrically conducting metal melt interacts with the field lines stretched by the magnet system. Force sensor and the magnet system form a so-called Lorentz force flowmeter. In this paper we present a series of model experiments that demonstrate the feasibility of using two identical flowmeters that are arranged in a certain distance one behind the other. In this case, surface velocity may be determined by just cross-correlating the two force signals recorded by the two sensors. This technique is called time-of-flight LFV. A special prototype of a respective measuring device, called meniscus velocity sensor (MVS), has been developed to measure local free-surface velocity. In the present paper we describe experimental results of respective measurements in the model test stand LiMeSCo (liquid metal surface velocity correlation). To check the potential of the time-of-flight technique, in a first step we measure surface velocities during solid-body rotation of metallic substances. We observe that small modulations in the signals that are due to the natural unevenness of the solid body can be used to determine surface velocities. In a second step we apply the time-of-flight technique to liquid metal free-surface flow. Here we use the low-melting eutectic alloy GaInSn as a test melt. In this case we observe that the cross-correlations between the signals are much rarer and much weaker than in the solid-body experiments. We conclude that the presence of the localized magnetic fields, produced by the permanent magnets of the flowmeter, give rise to intense deformation of the free surface and the creation of surface waves. The field acts as a magnetic obstacle. We observe that the flow velocity is decreased right underneath the magnetic field and is accelerated in the side regions. This magnetic obstacle effect may restrict the determination of the local surface velocity in application.

Jan 1, 2012

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By John L. H. Patterson

Handheld XRF has become the favorite way of measuring the content and identity of alloys in the field. This is because of the very portable nature of the instrumentation and its simple operation. However, these analyzers have been unable to determine the concentration of the light elements like Mg and Si due to the very low energy of the x-rays produced by these elements. In the past accessories such as vacuum and He flush have given some analyzers the ability to determine these light elements with modest detection limits. The introduction of the Silicon Drift Detector (SDD) into this class of instrumentation has added a new level of analysis capability to portable XRF instrumentation. X-ray fluorescence is achieved by exciting a sample with a beam of x-rays, which in recent portable equipment are generated by a small tube. This results in the emission of characteristic x-rays from the sample under test. By measuring the energy of each x-ray it is possible to determine what element generated it. By counting the number of x-rays at each energy it is possible to determine the concentration of each element. The detection limit for each element is dependent upon the number of x-rays which reach the detector. As the number of x-rays increases the detection limit will improve. One of the major factors in an x-ray reaching the detector is the energy of the x-ray. As the energy of an x-ray increases the probability of that x-ray reaching the detector increases. The energy of an x-ray is inversely proportional to the atomic number (AN) of the element generating the x-ray. For example, an iron x-ray (AN=26) is 6.40 keV while an aluminum x-ray (AN=13) is 1.49 keV. As the energy decreases, the detection of the x-ray becomes less and less probable because the x-ray may be absorbed by the windows which are part of the instrument and detector or the air in the path between the sample and detector. In SiPIN based portable XRF analyzers, the lowest element which is detected with acceptable detection limits is normally considered to be Ti (AN=22). The detection limits for 60 second measurements on typical SiPIN XRF analyzer are given in Table I. Thus, portable analyzers have not been useful for measurement of aluminum and titanium alloys as major components of these alloys are Mg (AN=12), Al (AN=13) and Si (AN=14).

Jan 1, 2009