Search Documents

By John W. Ahlrichs

Microscope, electron microprobe and x-ray diffraction have been used to provide quantitative evaluation of products from the mill, smelter, refinery and other metallurgical processes. Phase compositions and their quantities are necessary for an adequate understanding of the various products obtained throughout an operation and in laboratory testing. By careful evaluation, important information can be gained in improving recoveries and increasing grades at various stages of processing. Four case histories are discussed in this paper. Quantitative microscopic counting techniques are applied to mill products to determine degrees of locking and liberation of the economic minerals. Rapid, but accurate evaluation aids the metallurgist to develop or improve the grinding and flotation circuits. In the smelter, the identification and quantification of the phases are important for predicting reaction mechanisms and kinetic trends. Mineralogic techniques have been applied to conventional smelter products, and to those obtained in laboratory tests for newly developed innovations to smelting. Small, but important, values of gold occurrences in ore are difficult to determine. Evaluation of gold usually requires special separations into various mineral concentrates, followed by assays and mineralogic determinations of the products. Numerous occurrences of solid solution constituents can be treated as by-products, but often they are deleterious to metallurgical treatment. Most solid solution problems can be unraveled by the mineralogist's tools.

Jan 1, 1981

By Atul Kurnar

In the present research a two-cell polymer electrolyte membrane fuel cell stack (PEMFCS) with SS-316 bipolar plates has been tested. Different flow field designs were studied and a modified multi-parallel channel design is proposed. The stack is stable within ±3 mV even after 1000 hours of continuous operation, indicating efficient water management and effective removal of any metal ions from the stack. Also no iron is detected in membrane electrode assembly (MEA) by EDAX analysis after 1000 hours of cell operation. Results indicate that high operating pressures beyond 138 kPa didn't significantly increase the performance of cell, however added much to the pressurization cost of the system. Tests at different temperatures showed that at temperatures below 80°C, external humidification could be completely removed. The prototype stack is also tested under variable load conditions simulating highway-driving schedule. The experimental efficiency of PEMFCS is 48%, which is in good agreement with the model predicted efficiency of 53.8 %. Results show that 59% of the total losses are due to ohmic polarization in the cell. Further analysis on applications of the stack in automotive transportation system is in progress.

Jan 1, 2002

By R. Burkhard

Recovery of metals from complex mixed wastes is a challenging task of modem material and waste management strategies. Thermal methods are an important tool in this respect. Plasma turned out to be particularly useful for treatment of complex or toxic wastes and residuals. In order to study plasma processes at reasonable costs, a pilot plasma plant has been used and wastes like ~pent Raney-Nickel catalysts, copper and ah.:lminum drosses, and. other metal containing wastes were investigated. The paper summarizes the most significant findings

Jan 1, 1995

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990

By W. L. Dalmijn

Glass recycling in the Netherlands 'has grown fr.om 10.000 to 300.000 tonnes per annum. The various advantages and problems of the glass cycle with reference to the state of the art in the Netherlands is given. Special attention is given to new technologies for the automated sorting of cullet with detection systems. In Western Europe the recycling of glass has, become a success story. Because of this, the percentage of ,glass cullet used in ,glass furnaces has increased. To meet the quality demands of the glass industry, automated sorting for the removal of stones, non-ferrous metals and other impurities ,had to be developed and incorporated in glass recycling plants. ;In Holland, Germany and other countries, the amount of glass collected has reached a level that colour-sorting becomes necessary to avoid market saturation with mixed cullet. Recently, two systems for colour-sorting have been developed and tested for the separation of bottles and culletin the size .range of 20 -50 mm. With the increased capacity of the new glass recycling plants, 120,000 -200,000 tpy, the quality systems have also to be improved and automated. These quality control systems are based on tile automated sorting technology developed earlier. for the glass recycling plants. The data obtained are automatically processed and printed. The sampling system and its relation to the theory of Gy will be described. Results of both developments in glass, recycling plants will be described.

Jan 1, 1995

By M. B. Sizgoric

Quantitative mineralogy is used in a study done on an Inco Metals Company nickel sulfide occurrence from 'the Thompson area in Northern Manitoba. The study included: a) determination of the variations in chemical composition of the ore minerals; b) determination of the liberation of the ore minerals for the various types of ore and for different feed grinds; c) assessment of the preliminary mill test results by comparing the mineral distribution in the different tailings. Preliminary mill test results had outlined three main problem areas: 1) unacceptabiy low grade concentrate with, 2) very high weight recovery and, 3) low pyrrhotite rejection resulting in a high sulfur concentrate. The mineralogical study readily explained these results by showing that: 1) between 20 and 40% of the nickel in the feeds and 55 and 75% of the nickel lost in the tailings is associated with pyrrhotite. This accounts in part for the low grade of the concentrates obtained at high recoveries: 2) hexagonal nonmagnetic pyrrhotite constitutes over 90 percent of pyrrhotite. Since hexagonal pyrrhotite floats more readily than monoclinic pyrrhotite, this could be part of the reason for the undesirable high pyrrhotite recoveries into the concentrates. Further test work to establish both the optimal grind and the best conditions for pyrrhotite rejection is therefore mandatory.

Jan 1, 1981

The cleaning of copper containing fayalite slag using a CuFe alloy was studied under an oxygen pressure ranging from 10-7 to 5 X 10-11 atm at 1200º c. The reduction of copper from fayalite slags by Cu-Fe alloys was found to be very effective. For example, at a P 02 of 10-7 atm, the copper content in the slag was reduced from 4.1 to 0.402 wt. percent after 90 min. of reaction time using a Cu- 5.27 wt. percent Fe alloy. The copper reduction rates were found to be independent of P02 in the gas phase when using Cu-Fe alloys which exhibit an iron activity of greater than 0.4. A mechanism for slag c1eaning is proposed based on the concept that the Cu-Fe alloy lowers the oxygen potential of the slag according to Eq.1 1, fol1owed by the reduction of cuprous oxide by wustite as shown in Eq.2. Here X represents element X in the alloy phase while (X) represents the element in the slag phase. The copper and iron transfer behaviour obtained in this study are explained by a ?Stepwise equilibrium model.

Jan 1, 1985

By Pengfu Tan

NiModel, a thermodynamic model, database and computer program, has been developed to predict the distribution behavior of Ni, Cu, Co, Fe, S, O, As, Sb and Bi, and heat balance in the nickel pyrometallurgical processes such as Outokumpu flash smelting, Outokumpu direct high-grade matte smelting, INCO flash smelting, and Peirce-Smith converting processes. In this model, as much as 16 elements (Ni, Cu, Co, Fe, As, Sb, Bi, S, O, Al, Ca, Mg, Si, N, C and H) are considered. The compositions of matte, slag and gaseous phases, and heat balance are calculated using the thermodynamic data and the activity coefficients of the components derived from the experimental data. The model predictions were compared with the known industrial data from Kalgoorlie Nickel Smelter in Australia, Outokumpu Harjavalta Nickel Smelter in Finland and INCO Metals Company in Canada, and an excellent agreement was obtained. In this paper, the applications of NiModel in the nickel pyrometallurgical industries have been presented. NiModel has been used by Jinchuan Group Limited in China.

Jan 1, 2004

By Fiseha Tesfaye, Pekka Taskinen

"Thermodynamics of the equilibrium phase assemblage Ago_9Cul.lS-Cu2-xS-CuS have been studied by an EMF -method. The ternary phase was synthesized from the pure Cu2S and Ag2S in vacuum furnace at high-temperature and mixed with appropriate compositions of Cu2S and CuS to form the cathode electrode. The EMF-measurements were made on the solid-state galvanic cell Pt(-) I Ag I RbAg,ils I Ago9Cu1.1S-Cu2-xS-CuS I Pt(+), in a temperature range from 316 K to 498K.Based on the measured EMF vs. T relations, thermodynamic functions (?fG° , ?fS and ?fH°) of stromeyerite (Ag0.9Cu1.1S) in equilibrium with Cu2-xS and CuS have been determined. The obtained experimental values have been compared with the available literature values. New experimentally determined thermodynamic properties of the solid solution (Ag,Cu)2Sss were determined.IntroductionDue to intense mining of high grade sulfide ore minerals in the past, recently, the available sulfide ores are poor in metals and becoming increasingly complex; such that, the production of high grade metals by the conventional pyrometallurgical processes is compromised. Consequently, smelters are in need to modify their operating flow sheets and strategies for processing more complex feed materials economically, while meeting the strict environmental regulations. To make the appropriate modifications, accurate thermochemical data of phases and phase assemblages which exist in these complex ore minerals are essential.Silver-bearing sulfosalts are encountered in ore minerals for the production of base metals and are common sources of silver. Among the silver-based sulfosalts, stromeyerite (Ag0_9Cu1.1S) is relatively common ore mineral in most hydrothermal vein and replacement deposits [1]. Recently, the ternary chalcogenide compound Ago0.93Cu1,07S has been studied, intensively, due to its high ionic conductivity and gradual disorder in the sequential phase transitions [2]. Therefore, accurate knowledge of the thermodynamic properties of stromeyerite has considerable fundamental and practical interest in many aspects of extractive, chemical and physical metallurgy."

Jan 1, 2014

By Ali Hasham

Reduction rates of FeO in CaO-SiO2-Al2O3 slags by Fe-C melts have been investigated experimentally at 1723 K. The rates were estimated using experimentally determined CO(g) evolution rates. Flash X-ray images were employed to visualize the behavior of the melt-slag interface during the reactions. The influence of melt interface was examined by conducting two types of experiments - (i) dropping one (or several) Fe-C droplet(s) weighing 2 g into the molten slag bath, and (ii) dropping a small amount (10-30 g) of slag onto a Fe-C melt weighing 400 g. The rates from both types of experiments were compared and analyzed to determine the rate limiting steps. It was established that neither the carbon transport in the Fe-C melt, nor the transport of gas species in the gas film adjacent to Fe-C melt was responsible in limiting the reaction rate. It is possible that the slag phase mass transport may be controlling the initial reduction rate in the droplet experiments. However, a, different mechanism was responsible in limiting the reduction reaction when the overall %C in the droplets fell to about 2-3.

Jan 1, 1992

By Valdeci Paula Alvarenga, Sergio Luiz Costa, Itavahn Alves da Silva, Filipe Bueno Carvalho, Varadarajan Seshadri, Carlos Antonio da Silva

Use of fluorspar in steel refining operations is one of the environmental concerns and as such reduced consumption of this material or substitution of the same is one of the objectives. Industrial runs were carried out at Aperam Steel making convertor unit (Timóteo, MG, Brazil) using recycled/briquetted slag for partial or complete substitution of fluorspar. Samples were collected from the metal bath and slag after oxygen blowing to assess dephosphorization with several combinations of recycled/briquetted slag and fluorspar. The results showed that partial substitution of fluorspar by BOF slag briquettes did not affect the efficiency of dephosphorization. In general average Phosphorus content was reduced to 0.010% in the case of partial substitution compared to 0.016% in the regular refining procedure with no substitution. This replacement also resulted in 40% reduction of the fluorspar consumption in the converter

Jan 1, 2015

By David A. Neudorf

Known resources of nickel laterites considerably exceed nickel sulfide resources and there is a growing consensus that most new nickel production will be sourced from laterites. The development of nickel laterite projects is very capital intensive due to inherently low grades, inability to concentrate ore prior to processing, complex processing technology and typically large infrastructure requirements. This has resulted in most recently proposed projects being "mega-projects," to achieve economics of scale. However, this may result in unacceptable project risk in many cases. Furthermore, many known laterite resources are not large enough to support a mega-project. This paper describes an alternative model for nickel laterite project development that allows, smaller scale and reduces capital exposure. The requirements of this model in terms of process technology, infrastructure and commercial innovation are described. Keywords: Nickel, Laterite, Project, Economics

Jan 1, 2004

By Mototsugu Matsuno

A new process has been developed to treat fly ash generated from municipal incinerators, which contains not only toxic metals such as lead and cadmium, but also dioxins. The process includes the following steps; fly ash is formed into green pellets with some additives and the pellets are then roasted to eliminate or stabilize the toxic metals and to decompose dioxins. A pilot plant with a capacity of approximately 100 kg/hr was used to test the process. The tests verified that heavy metals were either volatilized or stabilized and dioxins were decomposed by high-temperature roasting. The pelletized ash was found to be non-toxic, so that it can be recycled as artificial lightweight aggregate. It was also found that volatilized metals collected as secondary ash can be recycled as smelting resources.

Jan 1, 2003

By V. I. Lakshmanan

The demand for elements such as nickel, cobalt, titanium and gold in various applications has increased significantly. Innovation to recover these elements now plays a major role in metallurgical processes as established technologies have challenges in treating the types of ores that are available while meeting the increasingly stricter environmental regulations. Alternative chloride based processes have been developed that can be used to recover the value elements from the available feed stocks with potentially lower environmental impact. Chloride-based hydrometallurgical processes have several advantages, including higher leachability of complex ores/tailings and relative stability of chloro-complexes of the metals. Process Research ORTECH Inc. (PRO) has developed mixed-chloride process flowsheets, where innovative solvent extraction process steps are used for the separation of nickel, cobalt, titanium and gold from their respective chloride solutions. This paper will discuss the potential aqueous chloro-chemistry of these metals and separation reaction mechanisms involved in the solvent extraction process.

By Omid Marzoughi

Chromium has a wide range of applications, including as an alloy addition in various steels and also as a corrosion resistance coating. Carbothermal reduction of chromite ore (FeCr2O4) in a submerged arc furnace is an important industrial process for extracting chromium, but the energy consumption is excessive. It is suggested that one area for future research is the low temperature carbothermic solid state reduction of chromite to produce an intermediate product, which can subsequently be upgraded to ferrochromium. In this regard, a thermodynamic model has been developed to investigate this process and the effects of temperature, carbon additions and ore composition on the recovery of chromium and the grade of the ferrochromium, have been studied. Further development of the model may allow it to be applied to the simulation of other processes for the recovery of chromium from chromite ores.

By Michael J. Marinigh

"Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable.In converting furnaces which have tuyères such as the Noranda Reactor and the Teniente, Peirce- Smith and Hoboken converters, efficient tuyère line management is critical to optimizing blowing rates, increasing refractory life, and improving safety.This paper will describe recent improvements made to equipment used for tuyère punching, tuyère silencing, tuyère pyrometry and refractory drilling of tuyères and how the proper application of the equipment can lead to operational and safety improvements."

Jan 1, 2009

By Ph. Cauwe

This paper presents the experience that NESA and MECHIM have gained about recovery of non ferrous and precious metals from complex sulfide materials. Processed materials are from natural deposits or metallurgical by-products or residues. Roasting of these materials is closely related to the pyro or hydrometallurgical processes used downstream of the roasting. Conditions of a first step of roasting the SELECTIVE ROASTING, are analyzed and explained. The roasted products so obtained are characterised by an extended elimination of volatile sulfides (AS, Bi, Sb, Sn, Pb, Hg, ?? ) and are readily available for the pyrometallurgical recovery of non ferrous and precious metals. After the SELECTIVE ROASTING, thanks to. the high porosity obtained in the "selective calcine", the SULFATE ROASTING is per-formed in excellent conditions. Hydrometallurgical tests performed for the final calcine show a high recovery of non ferrous and precious? metals and require only simple and well known processes. Many experimental and commercial data are given.

Jan 1, 1983

By Józef Czemecki

Polish copper concentrates are characterized by high levels of impurities, particularly Pb and As. Two technologies are being used for copper concentrate smelting at KGHM Polska Meidz S.A., namely the shaft furnace process (Legnica Copper Smelter, Glogów I Copper Smelter) and a single-stage process for direct to blister concentrate smelting in a flash furnace (Glogów II Copper Smelter). Both technologies are used at different physical and chemical conditions which results, in different impurities behavior. The paper presents flow sheets for copper production in a plant using the shaft furnace process and in another in which a single stage flash process is used. The metals distribution in particular semi-products is given as well as a method for elimination of impurities from the copper production cycle. Methods are also discussed for alloy and matte converting and copper refining to obtain low Pb and As concentrations in anode copper (0.3% Pb and 1500 ppm As maximum) that are being used in the KGHM Polska Meidz plants. Useful co-operation between the plants using different technologies, aimed at the limiting the effect of undesired impurities on the quality of blister copper produced, is also described.

Jan 1, 1998

By Rick Honaker

Rare earth elements (REEs) contained in coal and associated mineral matter exist in several forms including micro-dispersed minerals, ion adsorption onto clay surfaces, and chemically bound. Tests found that REEs can be effectively recovered from certain components of three coal sources by leaching under mild conditions followed by solvent extraction. A range of pH values were evaluated at solution temperatures of 25 and 75 °C. When using 1.2 M of sulfuric acid, nearly 85% recovery of the REEs was extracted from the middlings material collected from an operating plant. Acid leaching of a second middling source from another plant resulted in 60% of the total REEs being recovered under the same leaching conditions. Solvent extraction treatment of the leachate produced from six different coal sources resulted in products containing up to 50% total REEs from feedstocks starting with around 300 ppm.

By G. Mark Aylmore

Various processes have been developed using a combination of elevated temperature and chemical treatment processing to recover Li from silicate minerals. To facilitate further process development, a comprehensive understanding of the deportment of Li and associated minerals in ore bodies is essential to allow the industry to predict the response of ore reserves to metallurgical treatment options. This paper describes results from the integrated use of the John de Laeter Centre’s state of the art analytical and mass spectrometry techniques to characterise a selection of Li bearing ore bodies and determine their amenability to potential processing options for the extraction of Li. The mineralogy, mineral associations, and liberation characteristics of ore-bearing and gangue minerals were characterised using a combination of the TIMA and XRPD studies. The Li content and distribution within minerals were defined using LA-ICPMS and field emission scanning electron microscopy techniques (EBSD, ToF-SIMS) and atomic probe microscopy.