Search Documents

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

The method of ultrasonic-assisted leaching was used to extract vanadium from the stone coal, with alkali as leaching reagent. The effects of ultrasonic power, concentration of alkali, reaction temperature, liquid-solid ratio and reaction time were investigated, respectively. The optimal ultrasonic leaching condition for vanadium extraction is as follows: ultrasonic power 230W, concentration of alkali 5%, liquid-solid ratio 3:1, reaction temperature 90℃ and reaction time 1h. The leaching rate of vanadium reaches 76.4% under the optimal condition, which is 12.2% higher than that of non-ultrasonic leaching. The reason on enhancing the leaching rate of vanadium by ultrasonic leaching was discussed. It is indicated that the ultrasonic cavitation can increase the surface area of mineral, which is beneficial to facilitate the reaction rate. Keywords: stone coal; vanadium; alkaline leaching; ultrasonic

Jan 1, 2014

The oxidation of ferrous ions by oxygen in sulphate solutions is a very slow process, but it tills long been known that the addition of sulphur dioxide increases the rate of reaction very significantly. The kinetics and mechanism of the process were investigated in the laboratory and the results confirmed the advantage of adding small amounts of sulphur dioxide to the oxygen stream for the removal of iron from solutions. The effect of various parameters on the overall rate of iron oxidation and precipitation was studied. In particular, temperature, acidity and composition of the gas mixture were considered and the optimum conditions for the precipitation of goethite were determined.

Jan 1, 1991

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

By Dietmar Eifler, Benjamin Jost, Marcus Klein

This paper focuses on the ductile cast iron EN-GJS-600 which is often used for components of combustion engines. Under service conditions, those components are mechanically loaded at different temperatures. Therefore, this investigation targets at the fatigue behavior of EN-GJS-600 at ambient and elevated temperatures. Light and scanning electron microscopic investigations were done to characterize the sphericity of the graphite as well as the ferrite, pearlite and graphite fraction. At elevated temperatures, the consideration of dynamic strain ageing effects is of major importance. In total strain increase, temperature increase and constant total strain amplitude tests, the plastic strain amplitude, the stress amplitude, the change in temperature and the change in electrical resistance were measured. The measured values depend on plastic deformation processes in the bulk of the specimens and at the interfaces between matrix and graphite. The fatigue behavior of EN-GJS-600 is dominated by cyclic hardening processes. The physically based fatigue life calculation “PHYBALSIT” (SIT = strain increase test) was developed for total strain controlled fatigue tests. Only one temperature increase test is necessary to determine the temperature interval of pronounced dynamic strain ageing effects

Jan 1, 2015

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior ofTiO2 nanopartic1es was thermogravimetrically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanopartic1es, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500°C at a heating rate of 1 C°/min. The weight increase curve showed a maximum of ca 30 wt% at around 750°?C and then gradually decreased to ca 12 wt% at 1000°C. This would be caused by the formation of TiS2 followed by the decomposition ofTiS2 to lower sulfides, such as Tit.0.8S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanoparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By S. -H. Jeon, Y. -S. Choi

"The three dimensional current distribution on the rectangular cathode is predicted using a boundary element method with a linear element of trigonal type. The effect of cell geometry and anode shape on current distribution is simulated. Calculated results compare well with experimental results. The proper combination of anode size and distance between electrodes increase the current uniformity.The importance of electrodeposition as a fabrication technology in the electronics industry is large and growing. The main advantages of this wet processing method, in comparison to other dry processing methods, lie in its high yield, rapid processing and low cost. In nearly every application of electrodeposition the pursuit of deposit uniformity, especially thickness uniformity, has been technically imperative. The thickness uniformity of the deposit depends largely on the current distribution over the cathode. The current distribution is primarily determined by the geometrical characteristics of the electrodes and the cell. Also the polarization at the electrode surface and the mass transfer affect the current distribution.The current distribution is an important consideration for those involved in designing electrochemical systems and electroplating systems in particular. Although it is important, the common practice in industry is to use trial and error method to design the cell that optimize the uniformity of current distributions in electroplating. The purpose of this paper is to illustrate the useof boundary element method to predict three-dimensional current distribution in rectangular cell.The calculation of the current distribution is possible by various numerical techniques, which include the finite difference method (FDM)1, the finite element method (FEM)2, and the boundary element method (BEM)3,4. These methods of the numerical calculation have various problems, respectively, but the BEM is considered to be the most efficient. This is due to the fact that the BEM has the advantage of solving field equations only on the surface of a calculation domain. A good comparison between the BEM and the FEM for the secondary current distribution in a Hull cell was made by Matlosz et al.5The fundamentals on the theory of current distribution in electroplating are well-established in the literature by a number of authors.6, 7, 8 However, a small fraction of these works have been specially addressed to three-dimensional analysis, and, mostly thel·10 have focused on the problem qualitatively rather than quantitatively.Extending the previous work to three-dimension, we developed the program for the quantitative calculation of 3-dimensional current distribution using a boundary element method with a linear element of trigonal type. Integrals with singularity from the fundamental solution have been analytically computed and it is shown in detail in the Iiterature11. This paper deals with the three dimensional current distribution for the electrode position of copper in a cubic type cell and the effect of anode shape, size and the distance between electrodes on current distribution is studied."

Jan 1, 1997

By M. -V. Wang

Hydrotreating and hydrorefining (HT and HDS) spent catalysts contain molybdenum, vanadium, nickel or cobalt at concentration levels that can make metals recovery economically viable. Quanzhou Jing-Tai of China has developed, through many years of operating experience in metal recovery from spent catalysts, a simple process for recovery of these metals and the production of environmentally benign residues. The process first subjects the catalysts to a low-temperature calcination step, followed by grinding of the calcine. The ground material is then leached with 10-20% v/v hydrogen peroxide to recover metals such as Mo, V and Ni or Co. This step has a selectivity that is greater than 95% for the metals. The undissovled residue, which contains mainly Ah03 and Si02, can be dewaterd and used in the production of masonry bricks. The pH of the rich liquor is then adjusted to between 0.5 and 2.5 by adding dilute sulfuric acid to co-precipitate Mo and V, with a recovery rate of greater than 99%. The lean liquor contains mostly dissolved Ni or Co, which can be recovered through precipitation at a pH of between 8.5 and 9.5 by caustic additions. The final liquor is then sent to an ion exchange step for final recovery and cleanup of residual metals. The effluent is then discharged after a simple wastewater treatment process, which has been found to meet all environmental requirements. The entire process has been found to be simple, cost-effective with minimal environmental impacts while achieving the goal of complete resource recovery from spent catalysts commercially.

Jan 1, 2000

By J. Brent Hiskey, Rebecca Grace Copp

The solvent extraction of yttrium and neodymium from copper pregnant leach solutions (PLS) using Primene JM-T, a primary aliphatic amine, has been studied. Effect of contact time, pH, sulfate concentration, and extractant concentration were investigated using synthetic and actual PLS systems. Standard experimental conditions were 5 minute contact time, pH ~2.5, and 10 % v/v Primene JM-T concentration. Distribution isotherms were constructed for the pure systems and for actual copper leach solutions. Synthetic solutions contained 100 ppm Y and ~75 ppm Nd. Samples of PLS contained 2 - 10 ppm Nd and 14 - 30 ppm Y. Results showed that complete extraction of both yttrium and neodymium occurred within five minutes and at pH values greater than 1. It was also found that sulfate concentration does not inhibit extraction at any concentration. Additionally, the distribution isotherms created show that extraction for these metals can operationally take place in one stage.

Jan 1, 2016

By Teruhisa HORITA

The durability of SOFCs is one of the critical issues to realize the SOFC systems. In order to improve the durability, a precise degradation mechanism should be clarified at the different functional ceramic interfaces in SOFC cells and stacks. This paper reviews the improvement of SOFC durability by the mass transport analysis especially at cathode/interlayer/electrolyte interfaces. We have made a precise analysis on the reaction of cathode with impurities. Especially at the (La,Sr)(Co,Fe)O3/CeO2/ZrO2 interfaces, a significant amount of SrCrO4 and SrSO4 were observed at the (La,Sr)(Co,Fe)O3 surface as well as inside the (La,Sr)(Co,Fe)O3 cathode, which suggested some process occurred for both poisoning. Possible degradation mechanisms were proposed based on the observation data.

Jan 1, 2016

By Eugene Jak

Copper sulphide processing technologies face increasing pressures associated with decreasing concentrate grade leading to increasing thermal inefficiency and lower productivity. Impurity concentrations are on average increasing, creating potential environmental risk and additional treatment costs. In copper flash smelters dust, partially oxidised materials and fume formed from the condensation of volatile impurities, are routinely recycled to the feed. In the converting stage the heat balance is maintained by charging anode reverts and other inert materials. In both cases, the thermal energy available from sulphide oxidation is not fully utilised or optimised. The productivities of both smelter and converter stages can be potentially increased through the addition of a high copper, low iron, low impurity precipitated copper product. Calculations are carried out for fayalite smelter and calcium ferrite converter slags using an optimised FactSage thermodynamic database. The potential for significant increases in smelter and converter productivities using existing technologies are predicted.

By Ana P. Paiva, Marc F. Comella, Sandra S. Reis, Joao N. Reis, M. Soledade Santos

"In this work, the influence of the malonamide structure, acidity of the aqueous phase and diluent on the equilibrium interfacial tension (IT) of N,N'-dimethyl-N,N'-diphenylmalonamide (DMDPHMA) and N,N'-dimethyl-N,N'-dicyclohexylmalonamide (DMDCHMA) in 1,2- dichloroethane (1,2-DCE), and DMDCHMA in toluene, with aqueous HCl, were investigated. IT isotherms were determined using the Du N ouy ring method. Densities of the organic phases were determined, and used to screen solute-diluent interactions. Formation of third phases was never observed; furthermore, ITs increase with the phase separation period, constant values being obtained for separation periods larger than 1000 seconds. Each malonamide interfacial efficiency at the oil/water interface is interpreted in terms of malonamide basicity, diluent polarity and malonamide - hydrochloric acid- diluent interfacial interactions.IntroductionFor several years now, N,N'-tetrasubstituted malonamide derivatives have been extensively investigated as liquid-liquid extraction agents since they were first proposed as the organic components of the DIAMEX process, with the aim of advantageously replacing tributylphosphate in PUREX [1]. Therefore, a significant part of research studies with malonamides appearing in the literature deal with the extraction of major and minor actinides in real or simulated spent nuclear fuels in nitric acid solutions [2]. Under typical experimental process conditions, the tendency shown by some N,N'-tetrasubstituted malonamide derivatives to aggregate in the organic phase, leading in a few cases to the formation of undesirable third phases, has been remarked and consequently thoroughly investigated [3, 4]. The increasing use of chloride streams as hydrometallurgical aqueous feeds is becoming a reality, and this fact is obviously deeply founded on an extensive research carried out to recover value-adding metals from these media. Following this trend, a number of N,N'-tetrasubstituted malonamides have already been screened for the recovery of iron(III) [5, 6] and platinum-group metals [7] from hydrochloric acid solutions. The results obtained are quite promising either in terms of total metal ion recoveries or selectivity patterns achieved. The formation of a third phase when iron(III) was extracted by the tested N,N'-tetrasubstituted malonamide derivatives has never been observed under the adopted experimental conditions, and the extraction data collected would need to be reinterpreted accordingly if any aggregation phenomena involving the considered extraction systems were to take place."

Jan 1, 2011

By Nagahiro Saito, Takahiro Ishizaki, Daisuke Yata, Akio Fuwa

"Ternary compound-semiconductor, CuInTe2, film was deposited cathodically under potentiostatic conditions on titanium substrate from aqueous solution containing CuCl2, InCl3, TeO and HCI in this study.The deposition parameters such as electrolytic solution composition, potential and temperature were optimized· for electrodeposition of CulnTe2. Structural characterization of the: deposited film was also carried out using XRD and SEM. Electrodeposited films Were prepared and analyzed for their chemical composition using ICP. The ICP analyses showed that the stoichiometry of the films could be controlled by (1) the deposition potential and/or by (2) the electrolytic bath composition.1. IntroductionThe ternary chalcopyrite type compound semiconductors exhibit such electrical, chemical and optical properties that make them promising for photovoltaic devices (Kazmerski and Wagner 1985)(1). Many researches have been devoted to the characterization of these materials for over one and a half decades. High efficiency solar cells based on p-CulnSe2/n-CdS have been reported (Mickelson and Chen 1983)(2).The electrodeposited fil ns of semiconductors have more advantage than other physical and chemical deposition techniques; it is relatively easy and economic technique and the semiconducting properties such as band-gap variation, concentration of dopant stoichiometric composition and so on can be controlled with some accuracy. The electrodepositions of the ternary CuInS2, CulnSe2 have been reported by many workers (Hodes and Cahen 1986, Bhattachaya 1983, Singh et al 1986, Lokhande and can be prepared as both p-type and n-type. Therefore, its potential for application in optical and photovoltaic devices is one of the great interests. Bhattacharaya and Rajeshwar (1986)(9) reported the electrodeposition of CuInTe2 from an acidic bath· on indium tin oxide (ITO) and Mo substrate. Triethanolamine (TEA) was used as a complexing agent for indium. The electrodeposited CuInTe2 films were non-stoichiometric in composition under all their experimental conditions by electron-probe micro analysis (EPMA) and Auger depth profile analysis. In this paper, we report our results on the behavior .of Cu-In-Te electrodeposition from ·acidic baths; the preparation of CulnTe2 and the effect of bath composition on electrodeposited films obtained."

Jan 1, 2000

By R. Gampala

The consolidation of mom matrix composite monotapes occurs by the plastic (time independant) and creep deformation of monotape asperities. Past models of the process used seperate micromechanical analyses of the contact deformation by (rate independent) plasticity and power law creep (i.e steady state creep). These models are now used to simulate consolidation and to optimize/control consolidation process cycles so that the composite's microstructure is "steered" to, a user defined goal state. However, the models do not incorporate the sometimes dominant transient creep process and the instantaneous response of the plasticity mechanism causes finite discontinuities in the microstructure state vector field and therefore eliminates the possibility of using the powerful array of trajectory optimization schemes that all require continuous vector field for optimization and control. To overcome this problem, a inified creep/plasticity constitutive model that results in a continuous state vector field is used to rederive the contact deformation response during monotape consolidation. The contact blunting of a laterally constrained hemispherical asperity is first analyzed and its response represented by two coefficients; one relating the contact area to the blunting strain (C), the second, the mean contact pressure to the blunting rate (F).The C and F coefficients for this unified blunting problem are then obtained by finite element analysis, and detailed results presented for two composite matri-ces of topical interest (Ti-24A1-11Nb and Ti-6Al-4V).

Jan 1, 1996

By U. Meyer, A. Alonso, P. Banios

The sampling of cathodes has changed with the introduction of the ISA-process in copper refineries. A Jernkontoret joint working group of refineries and rod plants from both primary and recycled copper plants has been investigating whether the actual sampling of cathodes is representative for this type of cathodes. As a first stage, samples were sent to the members of the working group with the objective to find an easy basis for a comparison of the results of the next stages. All samples show the same tendency for nearly all elements. In some cases, there may exist differences in calibration and for some elements the detection limits are too high, especially when Optical Spectrometry is used. In the second stage, discs were compared with melted samples to answer the question whether the punching of discs is sufficient for the quality control of the cathode. The analyses of the discs represent fairly well the cathode quality. There are differences between cathodes from different crops. Three punches are sufficient to determine the cathode quality. Finally, samples from various lots of cathodes were compared with samples from the rod produced from these cathodes. The impurity content of the rod corresponds to the impurity content of the cathode.

Jan 1, 2000

By Huanmei Yuan, Yuanyuan Wang, Hao Bai

Composite phase change materials are widely used in energy-saving and energy efficient process. Nano-encapsulated phase change materials are especially significant for making advanced working fluid applicable to waste heat recovery or storage. In this study, silica-coated stearic acid (SA) Nano composite phase change materials were prepared from tetraethyl orthosilicate (TEOS) and stearic acid (SA) via sol-gel process. The materials were investigated by Field emission scanning electron microscopy (FE-SEM), Transmission electron microscope (TEM), Fourier transform infrared spectroscopy(FT-IR) and Differential scanning calorimeter (DSC).The FE-SEM and TEM results show that monodisperse microspheres with stable core– shell structure were formed and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reaction between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity.

Jan 1, 2016

By R. Padilla, M. C. Ruiz

Arsenic, antimony and bismuth are commonly found in copper concentrates usually as the minerals enargite, stibnite and bismuthinite, respectively. Concentrates having high levels of arsenic and antimony must be pretreated before smelting. Roasting is the preferred method for removing these toxic impurities from concentrates; However, the removal of As, Sb and Bi in oxidizing roasting by volatilization may not be complete due to the slow reaction rates at 500- 700 °C. Oxidizing/volatilization data were obtained from pure mineral mixtures and from arsenic rich copper concentrate. The reaction mechanism for the volatilization of arsenic and antimony were discussed. Near 100% As and over 95% Sb volatilized in the oxidation of a mixture of pure minerals at 700 °C, 1% oxygen, while over 95% As, and 35% Sb volatilized at 600 °C in 1% oxygen atmosphere when using a copper concentrate containing 3.51% As, 0.14% Sb, and 0.01% Bi. Bismuth did not volatilize.

Jan 1, 2015

By Min Chen, Lei Xu, Liang-yu Jin, Xue-liang Yin

For the purpose to reduce the high cost and heat storage loss of Al2O3-MgO bricks used as ladle linings, Al2O3-MgO-CaO bricks with lower theoretical density were fabricated and the densification behavior as well as mechanical property of this refractory was investigated. With addition of CaO, the initial sintering temperature of Al2O3-MgO refractory was decreased from 1300 to 1100°C associated with the expansive formation of CA2, and the compressive strength was also enhanced owing to the formation of bond linkage between CA6 and spinel. At high temperature, brick with 4% CaO content showed poor sinterability with high porosity because of the formation of platelet structure of CA6 grains, whereas brick with 8% CaO content was well sintered with higher relative density but lower bulk density than Al2O3-MgO brick, indicating that the densification as well as lightweight of Al2O3-MgO refractory was effectively promoted.

Jan 1, 2015

By James J. Komadina, Robert R. Beebe

"Heap leaching of gold ores has enjoyed wide acceptance in the arid and semi-arid regions of the western U.S., Australia and South America. There are areas, however, where cold weather or excessive precipitation can limit the usefulness of heap leaching. Even in Nevada difficulties can be encountered which call for special operating procedures.The paper discusses the general climatological limitations and some of the techniques used to extend heap leaching into colder conditions. A case history of the Cripple Creek and Victor Gold Mining Company operation in Colorado examines 'valley-fill"" technology as an ideal cold-climate solution, where topographical conditions permit.AcknowledgementsThe authors gratefully acknowledge the management of Independence Mining Company for their permission to present this paper. The contributions of Golder Associates; Pikes Peak Mining Company Environmental Affairs Department staff, and the Colorado Department of Mines and Geology were all invaluable in successfully concluding this project.BackgroundWhen heap leaching of oxidized gold ores was introduced in the rnid-1970s it was aimed at large tonnages of low-grade material which could not, in general, be developed via conventional milling. Normally, the reasons for this were economic rather than technical: capital and operating costs for milling were simply too high. At first, grade was almost the only criterion, but deposits too small to justify milling were also potential targets for heap leaching.Renewed interest in gold was centered in the western United States and Australia, where exploration for milling-grade deposits had never really died. When heap leaching came along, it was in these areas that the first developments took place. Coincidentally, these same areas were favorable for heap leaching: climates were temperate for most of the year and competing land uses were limited. Even so, in the western United States in particular, winter temperatures were low enough to complicate operations. Precipitation was less a problem, although heavy snowfalls could periodically interfere as well."

Jan 1, 1997

By Ian Masters

Rotary furnaces are widely used throughout the metals industry. These furnaces vary in size and geometry, but are fundamentally the same from a thermodynamic viewpoint. A generic method is proposed that can be used to model all furnaces of this type, provided that the correct material and process parameters are known. Various approaches have been attempted in the past based on a continuum (FEA or CFD) approach. However, the complex fluidlsolid interactions present in a rotary vessel are not easily solved using these methods, which work best where the material boundaries are well defined. In this paper a lumped parameter model is proposed. Variations within a section of the model are ignored, but to ensure thermodynamic correctness, the heat transfer between sections is carefully considered. For example, it is reasonable to assume that the whole of the melt pool is at the same temperature, due to rotary mixing. This may then be modeled with a single set of parameters, and the detail is contained in obtaining the correct heat transfer mechanisms from the rest of the furnace.

Jan 1, 2002