Search Documents

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi?industrial scale experimental system, Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/em3J has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/em3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition or the car engine.

Jan 1, 2003

By Milan Lj. Stamatovic

The hydrometallurgical recovery of zinc from recycled blast furnace dust from a steel plant (Smederevo Metallurgical Company - Yugoslavia) was investigated. The dust contained 22% Fe, 17% Zn and 0.2% Pb. X-ray diffractometry showed that the main components were hematite and magnetite, in combination with zinc oxide and a very low content of lead oxide. Individual particles were generally spherical and ranged in size from 10 to 150 microns; 63% were less than 33 microns in diameter. An effective hydrometallurgical approach proved to be by caustic leaching followed by electrowinning. Recovery of zinc in the form of zinc powder was over 90%. This powder can be used for the cementation of impurities in the conventional hydrometallurgical process for zinc production.

Jan 1, 1993

By Z. Y. Xie

The visualization techniques were employed for the analysis of computer simulation studies of dislocation core structure in ordered alloys. Atomistic computer simulation was used for the study of the local configuration of the material in the vicinity of the dislocation. Stresses were applied in the simulation in order to study the necessary stress level for the dislocation to move and onset plastic deformation of the material. The results were analyzed in terms of the strain tensor as a function of the position (x, y) in the material with the dislocation located at (0, 0). Various visualization packages are used to plot the invariants of this strain tensor and to visualize the changes that the dislocation core undergoes under stresses until it finally moves.

Jan 1, 1993

By E. Legault-Seguin

The current industrial practice in the processing of nickeliferous laterites involves the precipitation and releaching of Ni and Co to allow separation from the major impurities of Mn, Mg and Ca. A direct solvent extraction process has significant advantages over this practice, which suffers from difficult and costly precipitation steps, lower recovery and inherently complex flowsheets. The present investigation involves the examination of Cyanex 272, Cyanex 301 and Cyanex 302 as extractants for the direct extraction of Ni and Co from major impurities associated with laterite leaching, i.e. Mn, Mg and Ca. For Co extraction, Cyanex 301 and Cyanex 302 are superior to Cyanex 272, because they are able to selectively separate Co from Mn, Mg and Ca. Cyanex 272 offers complete extraction of Co from Ni and Ca, but Mn and Mg pose difficulty. Ni can only be extracted selectively with Cyanex 301, thus another extractant selective for Ni, such as Versatic 10 or Cyanex 301, is needed to recover Ni if Cyanex 302 or Cyanex 272 is used for the initial extraction.

Jan 1, 2004

By R. S. Tahautdinov, A. N. Posazhennikov, V. V. Bastrygin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2011

By James D. Navratil

Ferrites have been used to separate a wide range of substances such as dissolved metal species, particulate matter, and organic and biological materials; they have been used almost exclusively for metal waste treatment applications. The versatility of the ferrite waste treatment technique is evident in the wide variety of application methods. Furthermore, ferrites can be used to remove selected impurities in feed solutions containing metal products requiring purification. A brief overview of ferrite properties and recent applications for metal recovery and waste processing will be presented.

Jan 1, 1990

By M. H. Lin, S. Kou

"Czochralski pulling has been a very widely used process for growing single crystals for electronic and optical applications. Dopant segregation can significantly degrade the quality and yield of single crystals. We have used the floating-crucible technique for segregation control in Czochralski pulling, our floating crucibles being unique in that the melt passageway is very long. As such, dopant back diffusion is suppressed, even when the cross-section of the melt passageway has to be relatively large to help the melt go through or when the pulling rate is very low. Single crystals of model materials K-doped NaN03 and Pb-doped Sn have been grown with very uniform dopant concentrations. IntroductionSingle crystals of electronic and optical materials are often doped with a small amount of impurities to develop required physical properties, e.g., P and B in Si for n-type and p-type semiconductors, respectively, and Nd in YAG lasers. Dopant segregation can result in nonuniform physical properties, thus degrading the quality and yield of the resultant crystals.Figure 1 is an illustration of the conventional Czochralski process for crystal growth. Several techniques have been developed to control dopant segregation in Czochralski pulling, including the push-pull technique (1,2), the drop-pull technique (3-7) and the floating-crucible technique (8-13). The first two techniques require precise sensing devices and feedback control systems to keep the feeding rate equal to the pulling rate. The last technique is simple since the feeding rate is automatically equal to the pulling rate."

Jan 1, 1994

By Chuang Y-Y

A summary is made on the thermodynamic analysis for two of the four ternary systems of the quaternary Cu-Fe-Ni-S. The analysis is being extended to ternary Cu-Fe-S and then to the quaternary. An analysis is already made for the metal ternary but is not reported here. Experiment is being carried out to measure the liquidus surface. of Fe-Ni-S equilbrium with the fcc solid solutions of (Fe, Ni). The presentation at the Symposium will include all the results obtained at the time of presentation.

Jan 1, 1983

By E. V. Redin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Green pellets were processed via a lab tube (chamber) furnace to simulate RHF conditions. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2012

Off-gas cleaning from metallurgical plants requires? in many cases very low dust contents which are difficult to achieve with conventional scrubbers, even with high energy input. Lur.gi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to. the scrubbing zone. An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag' granulation after a waelzkiln achieving less than 1 mg/m3 in the clean gas.

Jan 1, 1992

By W. G. Davenport

Chapter 11 determined the combinations of industrial oxygen, oil and blast preheat that will steadily produce 65% Cu matte from pure chalcopyrite concentrate. It showed that the . combinations are described by a flat plane. It also showed that the minimum energy requirement for making 65% Cu matte occurs with maximum oxygen enrichment, zero oil and zero blast preheat. This chapter examines the, effect of matte grade on industrial oxygen, oil and preheat requirements.

Jan 1, 2001

By A. F. Sidorov

A method of improving mineral recoveries from ores by modifying the physical and chemical properties of minerals using radioisotope radiation was tested. It was observed that irradiation modifies mineral cell sizes, changes the crystal structure of some minerals, reduces the sulfur content 1 to 1.5 % in sulfides, changes the zeta potential, alters the surface properties of mineral grains I and produces other changes. Preliminary tests indicate that accelerated electron treatment of ores in connection with mineral processing has a potential for improving mineral recoveries by flotation and by magnetic separations.

Jan 1, 1989

TiO2 and Ti/TiO2 thin films were deposited on a quartz substrate by laser ablation of Ti02 and Ti targets using Nd:YAG pulsed laser. After sulfurization of the Ti02 film in H2S or CS2 gas at 1273 K for 1 hour, the surface atomic structure was changed. Furthermore, the Ti/TiO2 film was successfully prepared by the subsequent ablation of Ti and TiO2 targets. The morphology and structure of the films were characterized by XRD, XPS and AFM analyses.

Jan 1, 2003

By T. Nakamura

TiO2 and Ti/TiO2 thin films were deposited on a quartz substrate by laser ablation of TiO2 and Ti targets using Nd:YAG pulsed laser. After sulfurization of the TiO2 film in H2S or CS2 gas at 1273 K for I hour, the surface atomic structure was changed. Furthermore, the Tirri02 film was successfully prepared by the subsequent ablation of Ti and Ti02 targets. The morphology and structure of the films were characterized by XRD, XPS and AFM analyses.

Jan 1, 2003

By Hiroshi Nakajima, Kotobu Nagai, Toshihiro Hanamura

"Low carbon ferritic steel bars with ultra-fine grain structure was developed through a warm rolling for the first time by the present authors. They show better low temperature toughness than conventionally hot-rolled plates. Hence, the brittle fracture surfaces in Charpy tests were examined in terms of the effective grain size of fracture, compared with those of conventional QT steels. The ductile-to-brittle transition temperatures were in good accordance with those for the QT steels if referred to the effective grain size of fracture: · However, the size was a few times that of the ferrite grain. This means the grain refining is not yet fully utilized from the viewpoint of low temperature toughness. The anisotropy of· the impact properties and the annealing effect of highly dislocated structure on the toughness are also discussed in the present paper.IntroductionFor structural materials, both high strength and good toughness are required. Well-known approaches for obtaining better toughness for steels are as follows:1) Grain refining2) Addition of Ni3) Thin plate effect by cracking parallel to the rolling direction prior to crack propagation4) Contribution of metastable austenite.Among them, only the grain refining can raise the strength and improve the toughness. And it is well known that the finer the ferrite grain size, the lower the ductile-to-brittle transition temperature. For example, in the case of 0.11 carbon steel, the transition temperature decreases linearly to in d 1/2 [1 ]. However, these have been told in the regime of coarse grain size that is larger than 10 µm in diameter. There ~as .been no study dealing with the low temperature toughness in the regime of ultra-fine grain size with a diameter in the order of 1 µm."

Jan 1, 2000

By Robert W. Bartlett

Biooxidation of an ore heap containing only a few percent of sulfide minerals requires insertion of a very large amount of oxygen either by natural air convection, forced air ventilation or gaseous diffusion. While shallow heaps, those with lateral distances much greater than their height, are of great interest for many heaped ore processing operations, natural convection is often ineffective for oxidizing them because of inadequate lateral flow into the heap's interior. Oxygen can diffuse into a shallow heap from its upper, horizontal surface in contact with air. Oxygen diffuses through the air-filled void space within the heap, driven by the oxygen concentration gradient resulting from internal oxygen depletion caused by mineral oxidation. Oxygen diffusion, coupled with the chemical reaction kinetics oxidizing the sulfide minerals, is analyzed for conditions of rapid mineral oxidation kinetics, requiring small mineral grain sizes, and for typical ore heap biooxidation parameters. Practical limits on heap heights are presented for effective biooxidation of the sulfide minerals within times of interest for heap biooxidation of refractory sulfide gold ores, one to three years.

Jan 1, 1995

By Cleusa Cristina Bueno Martha de Souza

Hydrometallurgical techniques for processing metals are becoming an efficient method for recovering metals. Although batteries' manufacturers have got rid of mercury content, some efforts have been made for recovering other metals enclosed in the battery formula. This paper discusses the bench scale experiments in the purification process of leached solutions from alkaline spent batteries. After leaching process using sulfuric acid as leachant, the solutions containing Fe, Cd, Pb, MIl, Zn and K were neutralized to precipitate iron hydroxide. In a second step, the purification experiments were carried out with excess of zinc dust to try to remove Cd while Mn and Zn still remain in the solution to be recovered in an electrolysis stage. The purification experiments procedures were conducted at different temperatures and times to find out properly conditions from the viewpoint of metals removal After filtration the solutions were submitted to chemical analysis to certify the metals content extracted.

Jan 1, 2001

By Vladimir Kislik

Competitive complexation/solvation theory of solvent extraction constitutes a general framework for interpretation and quantification of ion-molecular interaction data in extraction systems. Depending on extracting metal -- solvent affinity constant and metal concentration ratios, four possible stages of extraction behavior and interacting mechanisms, are considered. Affinity constant ratios are easily acceptable through the independent measurements of three-component systems. Once determined and tabulated, the affinity constant ratio data may be used in any system of interest. Mathematical descriptions of the results are introduced for different interactions. Active solvent (including water) concentrations in the organic phase and temperature are included to the quantitative consideration. The theory allows direct comparison of the complexing/solvating power (competition order) of various extractants, active solvents and diluents. As a result, predictions for the extraction effectiveness and selectivity are possible. Some metal extraction systems are analyzed on the base of the theory. Analysis gives a key for preliminary quantitative prediction of suitable extraction systems.

Jan 1, 2003

By Kanchan Mondal

"Methanol, lower hydrocarbons, CO, and HCOOH formation have been by the reduction of CO2 with H2. Un-catalyzed electro-reduction requires a significant overvoltage. An alternate route has been conceptualized. Production of hydrogen from water can be achieved by chemical oxidation of a metal in water followed by oxidation of the hydronium ion by the released electrons to form hydrogen radical. It is hypothesized that circumventing the problem of the formation of hydrogen molecule is essential while having the hydrogen radical to react with CO2 forming methanol, etc. This may be possible by a bimetallic catalyst acting as a galvanic couple, wherein one metal acts as the electron donor for the production of hydrogen radical while the other acts as a catalyst for the reduction of CO2. This may enhance the reaction rates. The current concept circumvents the need for an external electric field unlike the electrochemical process.IntroductionUtilization of carbon dioxide as a raw material, not only as carbon sources but also as useful chemical feedstock is a more holistic approach to reduce air pollution by flue gases (1-3). Several methods have been proposed to maintain the concentration of atmospheric CO2 or to reduce and recycle it. One of these is the chemical fixations using catalysts. The conversion of CO2 to methanol by hydrogenation over copper containing catalysts is one of the most widely studied subjects in this area. The limitation in this reaction is the low conversion of CO2."

Jan 1, 2008

By T. J. White

A synthetic Mineral Immobilization Technology (SMITE) has been developed for stabilizing municipal and hazardous waste incinerator ash. Tailored additives are introduced to the ash in a' first stage that pre-stabilizes all the toxic metal components in non-volatile forms. and in a second pyrometallurgical stage, these are converted to insoluble mineral analogues. It has been found that a combination of apatitie. spinal, anhydrite and monazite can immobilize all the ash components at high waste loading and high density. Typically the stabilized products contain in excess of 50 wt% ash and have densities of 2.5- 3.0 g.cc-1. Toxicity Characteristic Leach Procedure (TCLP) testing has demonstrated that the products well satisfy regulatory requirements. The cost of production and disposal of SMITE waste forms in 2-5 less expensive than. convential methods of solidification/stabilization. This paper will describe the principles of SMITE design for ash stabilization, outline the fabrication procedure, and present comprehensive microstructural and chemical data to validate waste form performance.

Jan 1, 1996