Search Documents

By V. Panchanathan

The rapidly solidified Nd-Fe-B powders form the entire basis of the bonded magnet industry At present the rapid solidification is carried out exclusively by melt spinning, producing flake like particles having highly stable and magnetically hard microstructure These particles are comminuted into powder before being processed into bonded magnets These powders are magnetically isotropic having coercivities from 4 to 16 kOe The other type of powder recently introduced for bonded magnets is the anisotropic powder made by the hydrogen decomposition desorption recombination (HDDR) process. The characteristics and application of these isotropic and anisotropic powders are discussed.

Jan 1, 1997

By M. Rosales

By a physical and mathematical modeling, the behavior of the tri-dimensional waving, and the movement of the gases at the Teniente Converter was studied. The mathematical model considers the condensed phases of white metal and slag, along the gas phase, and includes the k-e model for the turbulence description. Both the physical model and the mathematical model allow to conclude that from a fluidynamic stand point the Teniente Converter clearly can melt 3000 tpd of concentrates. Also, both models are suitable to predict the slag fluidynamics and its spacial distribution inside the Teniente Converter, and the splashing in the tuyere zone as well.

Jan 1, 2006

By Peter K. Eriksson

Nanofiltration is very efficient in separating heavy metals from water solutions, even if they contain strong acids. Desalination System, Inc., has many years of experience in this area, and this paper deals with three different such cases. The first case deals with concentrating the heavy metals in the pregnant leach solution from a copper dump leaching site with a surplus water problem. The increased copper concentration in the pregnant leach solution increases the capacity of the following copper extraction stage. The nanofIltration permeate is polished with a biomass adsorption column to remove the small amounts of remaining heavy metals, before being discharged. This method eliminates sludge handling and disposal, which are quite costly with the alternative precipitation process. In the second case, a complicated precipitation method was used to remove heavy metals from the waste stream of a specialty metals manufacturer. Nanofiltration was installed to increase the metals concentration four times, which greatly simplified the precipitation process. The chemical consumption and sludge production decreased by more than 80 percent, and the labor cost decreased by 66 percent. In the third case, nanofiltration was used to purify waste sulfuric acid solutions containing heavy metals, to meet the specifications for technical grade acid. Sulfuric acid concentrations above 30 weight percent were successfully purified in a multiple pass membrane system.

Jan 1, 1996

By Stephan Mulch, Christian His, Patrick M. Stephan, Thibault Champion

"When fuel costs increase dramatically, waste to energy (WTE) conversion technologies become a good alternative to produce energy. The potential energy available in domestic wastes, in developed countries, could be upwards of 4% of their total energy needs. Due to low energy recovery and low level of treated domestic wastes in many countries, the energy coming from waste is generally less than 0.5% of the country needs.Domestic waste incineration can convert heat to electricity for industry and housing and allow waste volume reduction in countries where land fills are a scarce resource.There is a request to improve existing combustion technology by increasing energy recovery with better heat transfer in the boiler and also by increasing lining durability with more resistant materials and technologies.The knowledge of corrosion phenomena and material performance allows Saint-Gobain Group to develop and propose high performance refractory lining solutions.IntroductionThe interest in alternative energy has been growing dramatically in the two last decades due to several combined factors, such as global energy demand, fuels prices evolution (e.g. crude oil, Figure 1) or environmental and geopolitics factors"

Jan 1, 2008

By Toshiyuki Hashida, Victor M. Lopez-Hirata

"Small-punch tests and determination of fracture toughness JIC were conducted at 4 and 77 K on new cryogenic JN1, JJ1 and JK2 austenitic stainless steels, after isothermal aging. Equivalent fracture strain ?qf determined by measuring the reduction of thickness in the small-punch test specimen. A linear dependence of JIC on ?qf was found in these new materials. Regression analysis of experimental data produced the following linear relation JIC = 1304.1 ?qf + 8.09 [kJm-2]. An analysis of present work relation was pursued on the basis of material properties and evaluation method of he. Results showed that the slope value has a strong dependence on material yield strength and JIC evaluation method. This linear relation is useful for the evaluation of fracture toughness JIC, measuring the equivalent fracture strain ?qf by means of small-punch test. Thus it can be useful for assessing the degradation of fracture toughness in small areas such as, the heat-affected zone in welded components.IntroductionCryogenic structural materials for superconducting magnets of fusion nuclear reactor are required to possess a good combination of strength and toughness. The mechanical properties are required beyond the capability of conventional austenitic stainless steels [1]. New cryogenic JN1, JJ1 and JK2 austenitic stainless steels were developed by the Japan Atomic Energy Research Institute (JAERI) [1]. The structure of superconducting magnets is constructed by welding of 200 = thick plates of these steels, which are solution treated at high temperatures and then water-quenched to avoid intergranular precipitation. However, the welding process involves heating and cooling [2], which cause microstructural changes in both base metal and weld. In this heterogeneous microstructure, it is important to estimate the fracture toughness of these materials at cryogenic temperatures. Therefore, it is necessary to evaluate the effect of aging process on the fracture toughness behavior of these new steels. To determine the cryogenic fracture toughness, the elastic-plastic JIC value has been co=only used [2]; however, the specimen size is much larger than heat-affected zones in welded components. Small-punch (SP) testing method, employing miniature specimens, has permitted to evaluate the fracture toughness behavior at different temperatures in different nuclear reactor materials [3,4]. Mao et al. [5,6] and Misawa et al. [7] found a linear relation between JIC value and equivalent fracture strain ?qf, determined by SP method in non-ferrous alloys and ferritic steels at room temperature and austenitic stainless steels at 4 and 77 K, respectively. So that, this kind of correlation would be very useful to assess the fracture toughness JICe values by means of SP test in small zones of welded components."

Jan 1, 2012

By John R. Hugens

Modifications in the ALSCAN method of measuring hydrogen dissolved in liquid aluminum have made it possible to monitor the level of hydrogen dissolved in liquid copper. Measurements from the tundish show a correlation with eddy current readings from the continuously cast and rolled copper rod from the continuous casting and rolling system at Amarillo. The measurements also indicate that the copper in the tundish is supersaturated with hydrogen.

Jan 1, 1994

By Roberto Javier Santiago

The main properties of Calcium Carbide seem to be the grain size and the CaC2 content. This paper tries to describe the Calcium Carbide used in the South-American steel plants and how and where it is added.

Jan 1, 2006

By Juliana G. Gutierrez-Paredes, Gabriel Plascencia-Barrera, Fidel Reyes-Carmona

In Mexico, many tonnes of nickel from waste petrochemical catalysts are dumped every year. In order to recover all that nickel, a hydrometallurgical reactor was designed. This design was performed in a systematical fashion, which included the chemistry of the system under study, both a kinetic and mass transfer study, and finally the use of the RID function, to optimize the reactor size. It was found that the NiO leaching with sulfuric acid is well represented by a first order reaction. The mass transfer results are in good agreement with the experimental results, obtaining over 95% nickel extraction in both cases. A marketing study was also completed that determined that it is possible to make a good profit by processing this residue provided the capital cost was low.

Jan 1, 2000

By Vânia L. L. Andrade

Igarapé Bahia Mine is located in Carajás area, northern Brazil. Currently Companhia Vale do Rio Doce operates there a CIP / heap leaching plant treating an oxide gold ore containing about 4 g Au /t and 0,2% Cu, which produces 11 t of gold per year. Recent geological survey has identified a signifcant copper-gold reserve underneath the oxide gold ore. The processing aspects of this copper-gold sulphide ore are described in this paper. It includes ore characterization studies, grinding and flotation tests, orebody variability assessment, flowsheet selection and preliminary economical evaluation Emphasis is given to studies aimed at depressing fluorine bearing minerals to achieve a clean and marketable flotation concentrate.

Jan 1, 1999

By V. K. Handa

Sterlite Industries (I) Ltd. started its copper smelter in 1996 and worked through the common problems associated with smelter start-ups. Specific issues in the converter area included converter blower IGV problems, punching machine reliability, converter spitting, back collar burning, ,and short converter campaign life. With a very young and dedicated team of engineers and technicians, smelter management assigned teams of three to four members to work scientifically and systematically through each major problem area to recommend and implement appropriate solutions. The converter mouth was redesigned with respect to tuyere and metal height to eliminate spitting and back collar burning. The air line was changed in places to reduce the pressure drop. A new back-up compressed air line and vessel was installed to prevent tuyere blockage in the event of a blower trip or power failure. The converter mouth liners and bricking around the mouth was modified to eliminate metal leaking through the pouring lip Modifications to the punching machines were made to address specific problems and preventative maintenance practices were further streamlined and reinforced to ensure 100% availability of hot metal cranes, converter blowers, punching machines, and ID fans. Matte availability and matte temperatures were improved by streamlining the upstream ISA and Rotary Holding furnace areas. Implementation of a detailed training program for the converter operators significantly improved the operation and morale. Water-cooled double hoods and a third converter were installed as part of the smelter modernization plan. The new hoods dramatically improved hygiene in the crane aisle while the addition of the third converter posed new challenges for the same motivated group of crews with respect to flip flop operation to keep the idle converter hot and to maximize in-stack time, managing crane/ladle logistics, and managing revert generation. This paper describes the converter operation's journey from the initial days of long blowing times and large revert accumulations to present operations with two converter flip flop operation, and also describes the team work, constant focus on increasing productivity and reducing costs, and benchmarking.

Jan 1, 2002

New method for processing of copper and nickel production feed has been developed and tested at pilot unit having 10 t/hr capacity. The process allows single-stage treatment of ore feed including that with high magnesium oxide content and resulting in the production of rich matte, high-grade matte, or moralised alloy for further leaching, as well as dump slag and off-gasses suitable for production of elemental sulphur, liquid sulphur dioxide, or sulphuric acid. Tests results and principal technical and economical parameters are presented.

Jan 1, 2006

By Thomas F. Nederpel

The production of zinc and zinc-aluminum coated strip can be reasonably accomplished on a single operating unit. However, if the hot dip coating line is equip d with only one mo 7 ten metal holding furnace, it is necessary to transfer liquid metal of different chemistries and reintroduce virgin material to obtain the 18" necessary balance of elements in the bath. Dofasco produces Galvanize and Galvalume on a coating line with a sin le liquid metal furnace and has developed not only an efficient liquid metal trans& system but also an effective means of reutilizing the zinc-aluminum mixtures without detrimental quality affects.

Jan 1, 1992

By Sergio N. Monteiro

Polymeric matrix composites reinforced with coir fibers are being used in many industrial applications such as automobile interior panels and cushions. These composites have relatively low mechanical strength due to the weak fiber/matrix interface. The objective of the present work was to investigate the effect of a surface alkali treatment of the curaua fiber on the mechanical behavior of polyester composites with different amounts of these fibers. The treatment, also known as mercerization, was performed with distinct concentrations, 0.1 and 10% of NaOH at 1 min and 1 hour, before incorporation of the coir fibers into the polyester composite. The results showed no significant change in comparison to similar untreated coir fiber composites. A microstructure analysis revealed that, in addition to reducing the hydrophilic characteristic of the fiber,the treatment also affects the surface morphology and impairs the fiber/matrix interfacial strength.

Jan 1, 2009

By Robert E. Moore

Renewed interest in olivine refractories has led to efforts to characterize them employing modern techniques of experimentation and data analysis. Initial studies have focused on determination of physical and thermophysical properties. Special equipment for the determination of thermal shock resistance and creep behavior have been constructed. Optimal compositions for maximizing various properties are being identified using appropriate statistical techniques. The overall goal is to develop response surfaces for each of a selected group of engineering design and use properties. Development of ?olivine Refractories? in the United States The term "olivine refractories" is used here because it does appear that domestic deposits of this rock will be the focus of renewed interest and "olivinell is the preferred term in this country. There are extensive deposits of high quality olivines extending through parts of Georgia. North Carolina and in the state of Washington. The eastern olivines are much more localized and extensively altered compared to the western materials. The Washington olivines exist as massive rock deposits in the Twin Sisters mountain area northeast of Seattle and their inaccessi-bility has slowed efforts to develop them. The North Carolina olivines have been used in steel plant applications since the 1930's. Geologists use the term "olivine" to describe assemblages of ortho-silicates. 2RO.SiO2, wherein the RO may be MgO. FeO. MnO. etc. When the RO consists essentlally of MgO and FeO. the material is called dunite and. as such, is synonymous with "refractory olivine." Refractory olivines utilizing North Carolina materials were developed for brick products by Birch and Harvey in this country around the mid-1930's. (I) Their work was completely independent of that of V. M. Goldschmidt and co-workers who used massive dunites located in Denmark. (2) These deposits are currently being mined by A/S Olivine of Denmark for the manufacture of a rather complete line of brick shapes for use in steel-plant. glassplant. and cement kiln applications. Birch and Goldschmidt

Jan 1, 1982

By Mark R. Jolly, Jean-Christophe Gebelin, Aleksander Cendrowicz

"Injection of wax patterns is the first stage of the multi-stage process of investment casting. The quality of the final casting and its dimensional accuracy is highly dependent on this stage of the process. Pattern waxes used in the industry behave in a complex visco-elastic-plastic manner. The modelling of such material behaviour is therefore not simple.In this paper a number of configurations of die will be shown in which the injection of the wax has been carried out for a range of processing conditions. Some of the dies are transparent and the movements of wax front observed can be compared with those predicted by simulation. Surface defects in final components will also be shown and compared with the location predicted by simulation software. Some discussion will be presented on the limitations of the software used and the time-scales achieved for practical use as a design tool within the foundry environment. IntroductionThis paper presents the research activities carried out at the University of Birmingham on the modelling and prediction of the behaviour of industrial investment casting waxes during the injection of wax patterns. These research activities are done in the context of a more global study of the fundamental aspects of the investment casting process, the FOCAST project. Regarding the wax injection process, the aim of the project is to achieve a better understanding of the key factors that will lead to better castings. The filling of the die during the injection has been studied. Some other phenomena such as shrinkage/warpage or creep under residual stresses are also studied, but not presented here. Two commercial investment casting waxes have been characterised in order to model their behaviour and predict mould filling and subsequent defects.This paper will present the models that have been used in our work, the simulation packages used, the experiments carried out to validate the modelling and exhibit the defects due to bad filling, and finally the numerical simulation results."

Jan 1, 2001

By Hartmut Rossel

VAW aluminium AG has built a "Recycling-Technikum" (Recycling Research Centre) to add a new arm to the company's Corporate Research and Development Department. The Recycling Research Centre, a pilot plant for scientific research, has been in operation since September 1993. These state-of-the-art facilities allow the investigation and optimisation of recycling techniques in 'a global way and in detail. Research is concentrated on the unit operations - processing, melting and waste-gas purification - with the available installations making it possible to compare different alternative process combinations on a 100-kg scale. One of the main targets of VAW research is the development of recycling techniques for packaging. The paper presents an approach to recover the aluminium contained in flexible packaging materials using an integrated melting and waste-gas purification system.

Jan 1, 1995

Over the years, numerous hydrometallurgical processes have been proposed as an alternative or complement to smelters for the treatment of copper concentrates. Most of these initiatives met with limited success. Bioleaching is applied commercially for secondary copper minerals heaps and dumps, and bacterial leaching processes are being developed for copper concentrates, although industrial application is still years away. More recently developed processes usually include pressure leaching and/or ultrafine grinding. This paper proposes a new leach process to treat copper sulphide ores or concentrates: the process operates under atmospheric pressure and uses limited concentrations of ferric sulphate as oxidant; the key to the process is the regeneration of the ferric ion, which can be effected in-situ (direct process) or ex-situ (indirect process) using SO2/O2. Examples are presented for the treatment of copper concentrates by agitation leach and of copper ores by heap leaching. Application of the process to copper gold ores and chalcopyrite concentrates is also discussed.

Jan 1, 1999

By Pedro Morales

At present the Codelco´s smelter & refinery business have growing complexities, concentrates with lower copper grades, higher impurities contents, and environmental restrictions which have lead to refocus the Codelco business, not only by considering the isolated developments for each of the Codelco´s Smelt & Ref complexes, but also as an integrated corporative complex scheme which improve the economy of scale, optimize the synergies, and include new technologies for higher productivity and lower operational costs. Accordingly, for the 2008-2012 period, Codelco have prepared a Development Plan integrated to the smelters and refineries business units that improve its single potentialities of and include the advances for the Teniente Converter [1] and Continuous Converting [2] Technologies, and also include the concept of uncoupling the smelting process from the converting process allowing a higher operational flexibility, and a better control of its contaminants. Thus, processing the white metal generated in the Teniente Converter unit of the smelter A into the smelter B has comparative advantages. These changes in the business concept allow an overall increment of the smelting capacity by processing only white metal as a final product through a very marginal investment in this way the total or partial conversion of the white metal into blister copper is eliminated allowing to use the available gas capture-treating capacity, and available acid plants for increase smelting capacity as well.

Jan 1, 2006

By G.A Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003

By Sesha S. Srinivasan

Mechanochemical synthesis has been employed to prepare new light weight complex borohydrides, Zn(BH4)2. The thermal calorimetric and gravimetric analysis of these complex borohydrides shows the hydrogen decomposition temperature (Tdec) of about 100° C with theoretical capacity of ~8.0 wt%. This advanced materials based technology is considered to be suitable for attaining the US-DOE grand challenge technical targets. The powder x-ray diffraction analysis of the mechanically milled Zn(BH4)2 exhibits the presence of zinc borate and NaCl phase. The FTIR spectra of BH4-ion in NaBH4 has a characteristic band at 2290 cm-1,whereas in Zn(BH4)2, it occurs at ~2061 cm-1 (bridging B-H bonds) and ~2451 cm-1 (terminal B-H bonds) as well. The reversibility of hydrogen decomposition and recombination process is carried out by PCT measurements with multi-cycling procedure.

Jan 1, 2006