Search Documents

By Ray Y. Lin

Chemical vapor deposition of tungsten carbide on the surface of steel has been investigated at temperatures between 400 and 550C in an atmosphere containing tungsten hexafluoride, hydrogen and benzene. The tungsten fluoride flow rate was maintained at 20 ml/min. The hydrogen flow rate was at 100 ml/min. The benzene concentration varied from 1.15 to 5.56% in the reaction gas. It was observed that the higher the temperature, the faster the deposition rate for tungsten carbide. But the dependence of the deposition rate on the benzene concentration was not systematic. From the x-ray diffraction analysis, it was observed that W, W2C and WC are all presented in the coating. The amount of each phase presented in the coating depends on the temperature and, to a less extent, on the benzene concentration. The microhardness measurement has also been done for all CVD carbide coatings obtained in this study.

Jan 1, 1992

By Malti Goel

"Technology advancements in fossil fuel based energy generation and consumption are currently being aimed at minimization of CO2 emissions. To attain energy security, India must accelerate the pace of economic development, while achieving reduction in CO2 emissions per unit of energy consumed. It would need access to advanced coal utilization technologies to be demonstrated on indigenous coal characteristics. Of specific importance would be: improvement in coal quality, increasing energy efficiency and suitability of other CO2 sequestration technologies for reducing CO2 footprints. There is need to address related risks and financial burden through adoption of policies and regulations including the issue of open access in energy research. In this paper, seven important areas of strategic plan that need to be pursued for managing CO2 emissions in steel energy sector in India are discussed.IntroductionWorld is facing a crisis of climate change, which follows in the footsteps of global energy and environment crises. Accumulation of carbon dioxide from the generation and utilization of energy is leading to greenhouse warming and climate change. The global warming is causing the boundary between four seasons to be fuzzy and resulting in more spiky weather. Significance of its impact on environment is also determining the technology development needs in various sectors of economy for taking remedial measures.To respond to climate change concerns, the steel industry is undergoing a transition. It is at the threshold of a rapid change in technology as it targets innovation to achieve 50% reduction of CO2 emissions per ton of steel produced. Fossil fuel use is the main contributor of increasing concentration of carbon dioxide in the atmosphere. The control of air pollution and CO2 capture are thus relevant for a coal based industry, whether thermal power plant or a demand side energy intensive industry. World steel production has shown phenomenal increase in first eight years of 21st century increasing from 780 Mt in 2000 to 1343 Mt in 2008 [1]. It was merely 28 Mt in 1900. The global CO2 emissions from steel industry are also increasing and became 2550 Mt (3-4% of total GHG). Indian industry contribution was 161 Mt (15% of direct emissions from industry). It is likely to grow further to keep pace with the accelerated economic growth of 8-9% per annum."

Jan 1, 2010

By Philip Thompson

"Carefully planned laboratory test programs provide valuable data regarding the amenability of low grade gold ores to heap leaching. The most common laboratory test is the column leach test. The overwhelming problem associated with this type of test is the limit on the test column height. Most laboratories use a three (3) meter (10 foot) high column as a standard test due to building ceiling limitations, sample size limitations, etc. This paper presents a case study in which an ore sample was tested in a 1.5 meter, a three meter, and a six meter high column to determine the effect of column height on the test results. Other important factors such as sample preparation protocol, preliminary bottle roll testing to determine appropriate crush size, column diameter requirements, and leach solution analyses, are also discussed.IntroductionColumn leach testing has been used for years by many laboratories to determine the amenability of low grade precious metals bearing ores to heap leaching. However, the test work can be compromised by poor planning, misinterpretation of results, and extrapolation of data beyond the reasonable boundaries of the experiment. Preliminary test work should be performed prior to column testing. This preliminary work provides valuable information regarding the response of the ore to cyanidation and aids in the design of the column tests.The sample should be screened into various size fractions prior to testing. The fractions are assayed to determine the gold content of each size fraction and of the overall sample. The most valuable preliminary test is the bottle roll cyanidation test which is usually performed on five kilograms of coarse sample in a large rolling bottle which can accept material up to 50 millimeters top size. The residue from this test is screened at different sizes to determine the distribution of unleached gold in the residue. Comparison of the gold distribution in the leach residue with the distribution of gold in the feed at the same size intervals provides an indication of the appropriate crush size for the sample. The overall gold extraction from the sample at the crush size tested is also determined from these data. Lime and cyanide requirements can also be estimated from this test. The viscosity of the bottle roll pulp and the size distribution of the feed and leach residue can also suggest whether agglomeration of the ore will be required prior to column testing. Ores which contain significant amounts of clays (greater than 5 percent) will generally require agglomeration to prevent plugging of the test column."

Jan 1, 1997

By Helvio P. G. Santafé Jr., Ruben J. S. Rodriguez, Sergio N. Monteiro, Teresa E. Castillo

"The coir fiber extracted from the husk of the coconut fruits are worldwide available in tropical regions as a low cost lignocellulosic by-product for many applications including composite filler in automobile parts. Possible uses above room temperature require information on the thermal behavior of these coir fiber composites. Therefore, the objective of this work was to perform thermogravimetric, TGA and DTG, analysis on polyester matrix composites incorporated with different volume fractions of coir fiber. In general, it was found that thermal degradation associated with weight loss occurred in three stages. Changes were also observed in the DTG peaks that could be attributed to the coir fiber participation through the decomposition of its lignocellulosic structure.IntroductionThe development of new materials has always been motivated by the need of improved properties. This was the case of modem composites with combination of properties that surpass those of conventional monolithic metallic alloys, ceramic or polymers, from which composites are made. A typical example is the synthetic fiber reinforced composite with specific strength i. e, ultimate stress divided by density, higher than any other monolithic material. Today, however, our global society is concerned with serious environmental problems and thus demanding that new materials be developed with distinct characteristics. They are known as environmentally correct and are expected to be sustainable, which corresponds to the condition of being biodegradable, renewable, recyclable and neutral with respect to C02 emission, considered the main responsible for global warning [1]. Synthetic fiber composites cannot meet these requirements. Consequently, new composite reinforced with cellulose-based natural fiber are being developed [2-8] and are already replacing the synthetic ones in several engineering fields including the automobile industry [9-11]. These composites have additional advantages owing to the lignocellulosic fiber benefits of being diversified, abundant, less expensive, lighter and of societal interest [8]. In some cases even technical advantages such as non-abrasive effect to processing equipments and more flexibility exist in comparison to synthetic fibers."

Jan 1, 2011

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994

By Jinrong Zhang

Fresh cyanide solution was treated by near UV light with the assistance of photocatalysts. Cyanide was oxidized mainly to cyanate. Photochemical behavior of the anatase and rutile forms of TiO2 was compared. It is found that anatase has a much higher activity than that of rutile. Bubbling of oxygen in the reactor showed no appreciable increase in cyanide oxidation, implying that the reaction is surface controlling. A very interesting finding in this study is that a natural mineral, ilmenite, can replace chemical titanium dioxide as the photocatalyst. Ilmenite without any treatment did not catalyze the oxidation of cyanide. But, after being roasted at high temperature with oxygen, the oxidation was enhanced dramatically. The mechanisms of photooxidation of cyanide and the roasting of ilmenite are proposed.

Jan 1, 1991

By Wilson Pascheto

This paper presents results of investigations performed as part of a Root-Cause-Failure-Analysis (RCFA) of a DC smelting furnace that was brick lined with MgO-based refractories. An unusual continuous contraction of the furnace hearth was identified during operation. Cracks in the refractories were envisaged after a major shutdown of the furnace. To determine the mechanism and causes of the unusual contraction behaviour of the furnace hearth, refractory samples were taken from the furnace at different locations and subjected to different analysis including Scanning Electron Microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDX), QEMSCAN and Electron Probe Micro Analysis (EPMA). Creep testing of refractories under different loads (ASTM C832) was also employed to evaluate the mechanical integrity of the used bricks in comparison with the new ones. Results of the various characterisation analyses revealed that there was an interaction between refractory bricks and molten material during furnace operation, which resulted in reduced creep resistance of the MgO-based refractories. This was verified by comparing creep performance of the used brick samples and new brick samples at different temperatures and applied stresses.

By D. M. Hausen

Microscopic point-counting of polished sections, in combination with x-ray diffraction analyses of representative whole rock samples, provides an efficient means to compare the modal mineralogic composition of different rock types. Major gangue minerals, e.g., quartz, feldspars, micas, amphiboles, chlorite, clays, etc., are estimated semiquantitatively by x-ray diffraction techniques, utilizing optimum grind, gridded sample surfaces and a sample spinner during scanning. Opaque to semi-opaque oxide and .sulfide phases are estimated by microscopic "point-count" and "gross-count" scanning. Total mineralogic compositions are calculated and normalized to 100 percent from XRD and microscopic data by computer programming. Comparative mineral analyses for different rock types, as well as quantitative microscopic data for various parameters, including particle and crystal sizes, textures, degree of alteration, paragenesis, etc., provide useful guides in mineral exploration, both in early stages of geologic mapping and later stages of economic evaluation. Several case histories are described.

Jan 1, 1981

By T. Kamata, S. Takemoto, H. Takeuchi, M. Takayanagi, Y. Akahori, I. Jimbo

"A cooperative research work on the silver recycling process is underway between Matsuda Sangyo Co., Ltd. and Tokai University in Japan. Silver wastes treated here are mainly from photograph industries where the concentration of minor element is steadily increasing in the recent years. The waste materials are concentrated and the impurities are removed by evaporation and slagging. In this paper, the industrial practice of wastes treatment is introduced and the result of the laboratory studies on the removal of antimony and tin from the binary and ternary alloys will be discussed. Characteristics in the behavior of antimony and tin during the process are also discussed with the observation of practical operation.1. IntroductionPrecious metals such as gold and silver primarily come from mining practice and the byproduct in copper smelting. However, the recycled amount of these precious metals have been increased 1 along with the environmental restriction and the widely accepted idea of saving resources on the earth in the recent years.· Though the recycle process of precious metals are comparatively simple from other metals refining, the process has been getting more complicated as wastes treatment has to deal with more impurity elements which are intentionally added to the products. Among these additives, antimony is used in the film materials in the photography industries to suppress its inflammability. Tin is another concern ,that is also coming from photography wastes; These minor elements have become problematic during the recycle.The removal of these minor elements has been in operation at Matsuda through a traditional oxidation refinement process using a reverberatory furnace. However, the complexity of the charge makes the recycle process more tedious and troublesome. In order to investigate the minor element behavior in the complicated materials system during the silver recycling processes, a cooperative research work is undertaken between Matsuda Sangyo Co., Ltd. and Takai University in Japan. Silver wastes treated here are mainly discharged from photograph industries where the minor element contents such as antimony, tin and bismuth in those wastes are steadily increasing in the recent years. The liquid wastes containing silver are concentrated and then treated pyrometallurgically with solid wastes from other sources, where the impurities are removed ·by evaporation and slagging. The purpose of this study is to investigate detailed behavior of impurity elements in the silver. containing systems."

Jan 1, 2000

By Georgette Smits

The gun-sprayed refractory lining of electrothermal furnaces used for the manufacture of carbon disulphide from liquid sulphur and charcoal at between 800 and l000°C are severely attacked during the process. A mineralogical study of samples of eroded refractory material disclosed that carbon disulphide had penetrated the lining, causing the precipitation of sulphides and carbon, and the decomposition of mullite, a major constituent of the lining, to corundum and amorphous silica. Calcium, iron, titanium, and chromium are undesirable cations in a refractory that is used in furnaces for the production of carbon disulphide, since they react readily with this substance. A series of tests, in which samples were exposed to different amounts of carbon disulphide for various residence times and at different temperatures, was carried out with eight types of aluminosilicate-based castable and brick refractory materials, to compare their resistance to attack by carbon disulphide. Mineralogical investigation of the test cores showed that castable refractory materials are unsuitable for this type of process because of the presence of calcium aluminates and other impurities in the cement. Of all the refractories that were tested, a mullite brick of low porosity, containing a minimum amount of impurities, appeared to be the most suitable for use in this type of operation.

Jan 1, 1989

By T. B. Braun

Cathode contamination is the principal factor affecting the quality of electrorefined copper. It is commonly accepted that annealability is unfavorably affected by the following elements, in decreasing order of adverse effect: tellurium, selenium, bismuth, antimony, and arsenic. Silver in cathodes has importance as it represents a nonrecoverable loss of silver to the refinery. Mechanisms for the contamination of cathodes by these elements are examined and the effect of operating variables on contamination, including anode composition, electrolyte composition, electrolyte temperature, addition agent practice, and electrolyte discard rate, are discussed.

Jan 1, 1976

By Maneesh Singh

During the various stages of iron & steel production a number of iron-rich by-products are generated. The traditional way to recycle them back to the blast furnace has been the balling - sintering process. These by-products can also be made into cement-bonded agglomerates for use as burden material for blast furnaces. In order to improve the quality of agglomerates the effects of various processing parameters on the properties of cement-bonded briquettes have to be controlled. This paper looks into the various aspects of producing cement-bonded agglomerates and using them as burden material for blast furnaces.

Jan 1, 2003

By Zhanjun Wang, Yongqi Sun, Mei Zhang, Zuotai Zhang, Min Guo

The role of fluorine on the viscous and crystallization behavior of CaO-SiO2-MgO-Al2O3-FetO-P2O5-(CaF2) slags were explored using the rotating cylinder method, non-isothermal differential scanning calorimeter (DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. It was found that the viscosity slightly decreased with increasing CaF2 content. It was also found that CaF2 addition can promote the primary phase transformed from MgFe2O4 spinel to Ca3(PO4)F, which was beneficial to the enrichment of phosphorus. Additionally, the structure of the slags explained by X-ray photoelectron spectroscopy (XPS) and magic angular spinning nuclear magnetic resonance (MAS-NMR) were further analyzed, which was well in accordance with the above analysis.

Jan 1, 2016

By E. Allaine

Carbochlorination kinetics of pure MoO3, Nb2O5, Ta2O5 and V2O5, by Cl2+CO+N2 gas mixtures was investigated between 380 and 1000 °C. Standard free energy of carhochlorination reactions and phase stability diagrams of these refractory metal compounds were calculated. The influence of total gas flow rate, temperature, reactants partial pressures on the reactivity of these oxides were investigated. The apparent activation energies were found to be about 83, 75, 110 and 100 kJ/mole below 650°C for MoO3, Nb2O5, Ta2O5 and V2O5, respectively. Above this temperature, the Arrhenius plots exhibit a rate anomaly attributed to thermal decomposition of COCl2 and/or structural changes of these refractory metal oxides. The apparent reaction order of carbochlorination of these oxides with respect to Cl2+CO was determined. For these refractory metal oxides, the reaction rate was maximum for a Cl2/CO ratio of about 1 in the chlorinating gas mixture. Results of carbochlorination of these oxides are compared and discussed.

Jan 1, 1995

By Magnus Ek, Peter Olsson

The Rönnskär Smelter has been faithful to Peirce Smith Converting during its 79 years of existence. Though a visitor to our smelter museum will easily find out that a lot has happened since the beginning – and development continues. In this paper an up-date on Converting and Casting at the Rönnskär Smelter is presented. Recent developments include an investment into converter process gas handling, but also day-to-day operational aspects such as converter aisle productivity and flexibility, but also minimal EH&S impact. 127

Jan 1, 2009

By S. Sugiyama, M. Kiuchi

"New metal working processes, such as the mashy-state mixing, mashy-state forging, mashy-state rolling and mashy-state extrusion are developed and applied to manufacture the so-called particle reinforced metals, fiber reinforced metals, particle reinforced cladding metals and so forth. These metal-ceramics composites are made of metal sheets, metal powders, ceramics particles and ceramics fibers. The mashy-state processes are also used to work those composites into bars, wires, tubes, plates, sheets, machine parts and other products. The working conditions necessary to manufacture sound composite products are clarified and the mechanical properties of the products are investigated. Through the investigation, it becomes clear that the mashy-state processes are useful and effective to manufacture metal-ceramics composites. It is al so known that these processes may be applied in various ways to development of new metal matrix compounds. IntroductionThe so-called metal-ceramics composites and processes to manufacture them are now being widely investigated in order to comply with increasing demands for new materials with novel and excellent mechanical properties and functions. The metal-ceramics composites are expected to have superior characteristics with respect to the elastic modulus, hardness, anti-wear resistance, high temperature strength and other mechanical properties to those of conventional metallic materials.The present authors ha v e been investigating into new metal working processes which are based upon the characteristics of metals and their alloys in the mashy-state. In the mashy-state, the metal (or alloy) includes both of the solid and liquid components. According to the fact that the partial melting takes place and the liquid component usually exists at grain boundaries, the metal in the mashy-state has quite different mechanical properties from those of the metal in the solid-state. Because of that the bonding force among grains is very weak due to the partial melting occurred at grain boundaries, the mashy metal has distinctively low flow-stress and high deformability. The mashy metal splits into grains or particles and sticks to others very easily. It is so soft as to be stirred up just like a lump of sherbet, but it is sufficiently viscous to be mixed up with other materials, such as ceramics particles and ceramics short-cut fibers."

Jan 1, 1988

By José Antonio, Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo, Antonio Ernandes M. Paiva

"The production of alumina from bauxite using the Bayer process generate 1.25 ton of the residue known by red mud and 460 kg of CO2 per ton of alumina.The direct use of exhaust gases from the alumina refineries to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing the reactivity of red mud and sequester approximately 15% or 67 kg of CO2 per ton of alumina.This paper shows the reaction of a suspension of bauxite residue-water with a simulation of the calcinator exhaust gases of the refinery. The influence of the temperature and the ratio water red mud is also analyzed.2 IntroductionThe production of millions of tons per year of alumina around the world generates around 1.25 tones of the residue known as red mud and 0.4 ton of CO2 per ton of alumina . The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity is considered dangerous and currently there is no operating process capable of reuse all the material at any refinery. These lakes after filled of solid material eventually have the surface revegetated. Otherwise will need monitoring for decades and remain as an environmental passive. The search of a industrial process that combine the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of use in large scale in a economically viable way is the main objective of this work.The use of the exhaust gases of the refineries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester million of tones of CO2 plus other gases like SO2 [7] and NOx.This project main objective is to study the reaction of the CO2 with the Bayer process residue in order to obtain the basic parameters to design an equipment capable of process this reaction on a pilot scale. With this objective compositions of red mud on spray were processed with flow of gas containing CO2 at different temperatures and with concentration similar to the exhaust gases of the calcination process of the refineries. With the results, basic concepts of a pilot scale equipment were evaluated.A revision of the work already done on this type of residue were done [3, 9, 10]. Alternatives and potential barriers on chemistry and environmental fields were discussed. With the objective of industrial application the potential use of these materials were evaluated through the pH control, mass balance and x-ray diffraction."

Jan 1, 2010

By Xianzhong Hu, Qingbo Yu, Qin Qin

"Oxy-fuel combustion is one promising option among different CO2 capture technologies. The object of this work is to show the effect of CO2 dilution on the laminar flame speed, flame structure and reaction pathway for methane oxidation at O2/CO2 atmosphere. In this paper, kinetic simulations were made using CHEMKIN with GRI-Mech 3.0 mechanism, which was validated by experimental data of laminar flame speeds. The reaction pathway of CH4/O2/CO2 mixture was derived from reaction flow analysis. Results showed that CO2 decreased the flame speeds, lowed concentration of major intermediates and increased flame thickness. The major chemical pathways of CH4 to CO2 have not changed at O2/CO2 atmosphere comparing with O2/N2 atmosphere, but contributions to major intermediates formation from each related elementary reaction have changed a lot. In addition, the secondary chemical pathways of CH3 oxidation became different at O2/CO2 atmosphere.IntroductionNowadays, as the global economy is developing fast and the pollutant levels (especially global warming gases) are increasing, a lot of researches are focusing on new technologies which can cut greenhouse gas emissions [1]. New technologies have been developed, such as high Mild combustion, flameless combustion and Integrated Gasification Combined Cycle (IGCC) technology. Oxy-fuel combustion using carbon dioxide as dilution of oxygen is considered as a promising approach for reducing CO2 emission. The properties of CO2 in flue gas are different from N2 in air. On one side, the transport, thermal and radiative properties of CO2 are different from N2 in air. On the other side, CO2 is not inert but directly participates in chemical reactions and recent researches [2-5] also present the chemical effects of CO2 on oxy-combustion. For these differences above, the characteristics of oxy-combustion are not alike with traditional combustion. It is necessary to develop the investigation of oxy-combustion.In all combustion processes, laminar flame speed is an important parameter, which links to combustion behavior. Analysis of this parameter can provide a better understanding of the effect of CO2 dilution in the process of oxy-combustion. Several investigations of laminar flame speeds of oxy-fuel flame have been improved, including experimental measurements and numerical computations. A.A.Konnov et al. measured the flame speeds of oxy-methane and oxy-ethane mixture using the heat flux method with a flat burner [6-8]. V. Ratna Kishore et al. used heat flux method to measure the adiabatic laminar flame speeds of hydrogen [9] and H2/CO mixture [10]. Adiabatic laminar flame speeds of hydrogen in O2/CO2 atmosphere are much smaller than in O2/N2 or in O2/Ar. The burning velocity of H2/CO mixture decreased with increase in CO2 content in mixture. Jeongseog Oh et al. [11] used Bunsen flame to measure the laminar flame speeds of premixed oxy-methane mixture with angle methods in atmospheric condition (300k, 1atm). The results were SL=29.1cm/s and SL=29.5cm/s respectively derived from oxy-methane from CH* images and Schlieren photos."

Jan 1, 2014

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By Shenghui Guo, Jian Chen, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"Response surface method (RSM) based on mono-factor experiment was applied for the process optimization of sintering of chromite fines by microwave. In RSM analysis, effects of binder addition amount, sintering temperature and holding time on the compression strength and shatter strength of the sinter were examined. Results showed that the optimal values of the above parameters were determined as follows: binder addition amount of 1.90% (in mass), sintering temperature of 1153? and holding time of 16 min. Under the optimized conditions, the compression strength was 11155.8? and shatter strength was 95.6849%. The results show that the process was optimized by response surface methodology is stable and feasible, and provide a new way for sintering of chromite fines.IntroductionChromite ore is the main feedstock for ferrochrome, and ferrochrome can be used as steelmaking additive to produce a variety of great strength, corrosion resistant and oxidation resistant special steel, which can be widely used in the aerospace, automotive, shipbuilding, military departments[1], and it has important strategic significance. At present, among the annual world's mined chromite the number of lump ore continues to diminish with its price rising sharply, while the proportion of ore fines been always increased, and the difference in prices between ore fines and lump ore is growing[2]. Despite the low price of chromite fines, and its rich in resources, it can be only used for ferrochrome smelting after agglomeration. Thus manufacturing blocks by using cheap chromite fines is an effective measure to reduce the cost of ferrochrome production and use the chromite resources[3]."

Jan 1, 2013