Search Documents

By Edmundo Manilla, Merete Tangstad, Daniel Davila, Eli Ringdalen

FeMn alloys are typically produced with lumpy ore or sinters. Minara Autlan, the Mexican FeMn producer, is however making Mn-nodules as a raw material for Mn-alloy production. The Mn nodules have been characterized by XRF, XRD, by wet chemical methods and by EPMA. The Mn/Fe ratio is somewhat lower compared to commercial Mn ore on the marked. The basicity of the ore is however close to 1, and additional fluxes may not be used. The Mn-nodules will be in a state of manganosite (MnO), tephroite ((Mn, Ca)2SiO4) and galaxite ((Mn,Mg)Al2O4). This leads to a low melting temperature area. A low porosity and low amount of higher Mn-oxides gives a high thermal strength to the nodules.

Jan 1, 2016

By Jim Sarvinis, Rory Hynes, Elizabet Cruz, Kerry McKenna, Maytinee Vatanakul

"Energy efficiency improvements achieved using heat recovery processes offer benefits to both the business case and environmental impact of metallurgical facilities. Global demand drives the development of lower and lower grade ore bodies. This trend results in higher energy intensity and consequently increased waste heat. Waste heat boilers and Organic Rankine Cycle (ORC) processes are becoming cost competitive methods of utilizing this waste heat.This study analyzes heat recovery from available sources to produce power using, • High grade: waste heat boiler and steam turbine generator. This system will produce electricity, and/or process steam.• Low grade: ORC to produce electricity. The cycle is well adapted to low- moderate temperature heat sources.Processes used in metallurgical plants, such as hot exhaust streams, cooling and condensers could benefit from application of these systems.The study demonstrates:• The energy and cost saving potential of waste heat recovery technologies,• The environmental benefit.IntroductionIn recent decades, process intensification has resulted in increased productivity from unit operations such as kilns, fluidized bed reactors and smelting furnaces and decreased unit operating costs. In the coming decades, the industry’s challenge will be to continue this trend while at the same time decreasing the consumption of fossil fuels and further reducing the environmental impact of its processes.The U.S. Department of Energy reports that available waste heat sources in industry, which is approximately seven quadrillion BTU (~7,400 PJ/y), exceeds the current production of all renewable power sources combined. In Canada there are about 2,300 PJ/y of available waste heat, with the pulp and paper, metallurgy, chemical/petrochemical and oil refining industries the main players. Natural Resources Canada (NRCan)9 has estimated that about 25% of that heat could be recoverable using existing technologies, which in turn, represents a reduction of 27 Mt/y of Green House Gas (GHG) emissions, plus considerable water savings due to lower water cooling requirements and less fossil fuel consumption."

Jan 1, 2011

By M. M. Kim

Zn-27% Al was pressure infiltrated into a column of 20 micron diameter abrasive grade SiC particles to give billets with particle loading of 50 voli.une %. Some billets were heated to a temperature where they became semi-solid and diluted with liquid Zn-27% Al alloy to give billets with particle loadings of 12 and 16 volume %. Some of these billets were then extruded into wire with an area reduction of approximately 98%. Tensile properties of the as-cast billets were always inferior to those of the matrix alloys; however, the extruded composite samples showed at 37% improvement in ultimate tensile strength compared to their extruded conventional counterparts. The fracture surfaces of these samples are described.

Jan 1, 1990

By Liyuan Chai, Bing Peng, Ji Peng, Di Yu

"Electric arc furnace (EAF) stainless steel dust has been classified as a hazardous waste by various government regulatory agencies as it releases heavy metals to environment. The solidification of EAF dust is to stabilize the hazardous components to the amorphous silica-alumina-based clays. The process of solidification is investigated and the softening temperatures of dust and additive clay mixtures are measured for economical thermal treatment. The results indicate that the mixture of dust and local clay with the ratio of 1:1 has the lowest softening temperature 1100 °C and it could pass the toxicity characteristics leaching procedure (TCLP) test for the environmental regulatory limits after thermally treated at softening temperature for 15 min. Major phases of thermal solidification product clinker are CaAl2Si2O8, (Fe, Cr)2O3, (Fe, Mg)(Cr, Al)2O4 and Al6Si2O13.IntroductionThe yield of stainless steels in China arrived to 10 million tons in 2006 and more than 0.2 million tons of stainless steel dust are produced annually. Approximately 1-2 wt.% of scrap charged to an electric arc furnace (EAF) enters the off-gases and then is converted into the dust and reported to the bag-house. The disposal or landfill of the dust becomes a serious environmental problem in China due to the increased production of stainless steels in recent years. The dust contains elements such as chromium (Cr), nickel (Ni), lead (Pb), zinc (Zn), cadmium (Cd) and their solubility in leaching media exceeds the environmental regulatory limits [1]. Even though easily feasible for low-grade MgO, it is not appropriate to stabilize the heavy metals from the heavily contaminated soils after the dust landfill [2]. Several dust treatment technologies have been developed and they can be divided into two types. One is to recover the metals from the dust [3, 4] and another is to stabilize hazardous components present in the dust [5, 6]. Recycling of the dust generated in EAF is a remediation option for cleaner production. Direct recycling of EAF stainless steel dust was developed to recover the metal value from the dust and protect the environment [7], but it was only suitable for the dust with high contents of Ni, Cr and Fe. As for the dust with low valuable metal content, thermal solidification is an appropriate choice for the dust treatment."

Jan 1, 2012

By M. A. Barakat

Large amounts of zinc ash and flue dust containing more than 80 % zinc are accumulated during galvanization processes at the surface of molten zinc bath and in the chimney respectively. Pyrometallurgical recovery of zinc from both of the ash and dust samples has been carried out. The ash was sieved with the help of an industrial sieve shaker provided with mesh sieve having a pore size 0.9 mm. The oversize fraction cut (+ 0.9 mm) was melted at 550 °C under ambient conditions. The produced ingot (1) was analyzed whereas the coarse fraction of the produced slag (+ 0.9 mm) was treated as the coarse ash or added to it. The dust was enriched with suitable fluxing salt prior to heat treatment at 600 °C for 1 h. The produced ingot (2) was analyzed whereas the resulting slag was mixed with the fines of the ash and treated by hydrometallurgical processing to prepare valuable salts of zinc. Parameters affecting recovery processes such as time, temperature and flux percentage were studied. Results obtained revealed that the two prepared ingots (1&2) were successfully recovered with recovery efficiency amounts to =85 %. The obtained samples meet the standard specifications with relatively low price. Also in the light of the strict environmental regulations of pollution control, reuse of these wastes materials will help in keeping the environment clean.

Jan 1, 2000

By Akira Kaneda, Nozomu Hasegawa

"In the Mitsubishi Continuous Copper Smelting and Converting Process, slag/matte mixture overflowed from the smelting furnace is separated continuously in an electric furnace (slag cleaning furnace, CL-furnace). In order to improve the separation efficiency of slag and matte and to minimize power consumption, the design and the operating conditions of the CL-fumace should be optimized. In the previous study, the authors developed a mathematical model for simulating phenomena in the CL-furnace. The model consisted of 3 modules, electric field analysis, heat and fluid flow analysis and the particle tracking method. In this study, the model was partially modified: k -E. model was adopted, and the effects of various conditions, such as furnace shape (including accretion) and scale, electrodes configuration, immersion depth of electrodes, and thickness of slag layer, were evaluated. And the optimum design and operating conditions were discussed.IntroductionUnder the recent environmental restriction, advantageous features of the Mitsubishi process have attracted much attention. The process uses 3 furnaces connected by launders. Mixture of matte and slag formed in a smelting furnace flows continuously to a slag cleaning furnace (CL-furnace), where the matte is separated from the slag. The matte is continuously siphoned out to a converting furnace and converted to blister copper. The slag overflowed from the CL-furnace is discarded. Because the slag contains about 0.6 % copper, improving slag/matte separation efficiency and decreasing copper loss make a great profit. Moreover the process requires a large amount of electric energy, so reduction of electric power consumption brings in enormous benefit.The objective of this study is to optimize the design and the operating conditions of the process, especially the CL-furnace. This will be achieved by developing the mathematical model and clarifying relations between the design or the operating conditions and various phenomena in the furnace. Fig. 1 shows an outline of the CL-furnace. The mixture entering through an inlet is separated to slag layer and matte layer . In order to maintain the temperature of the melt at a predetermined level, 6 electrodes are immersed into the lag and Joule's heat is generated by 3-phase alternating current flowing."

Jan 1, 2000

By J. F. White

An experimental study was undertaken to evaluate the feasibility of a selective chloridizing roasting pre?treatment process for the elimination of impurities from zinc feed?stocks prior to recovering zinc by conventional unit operations. In this investigation, a number of chemistries that might serve as a basis for such a pre? treatment process were examined. A variety of chloridizing agents were admixed with EAF dust to promote the selective removal of lead and cadmium by the formation of volatile metal chlorides, he results of the experimentation firmly establish that selective chloridizing roasting is a technically feasible means of eliminating lead and cadmium from EAF dust. Excellent extraction efficiencies were accomplished with a number of chloride additives; as high as 98 percent lead extraction and 88 percent cadmium extraction were attained with minimal zinc losses, Continuous pilot?scale tests reinforced the trends established by laboratory?scale experimentation, Attempts of chlorine elimination using pyrohydrolysis were less successful. The extent of chlorine elimination was found to be highly dependent upon EAF dust sample type and treatment temperature.

Jan 1, 1996

By G. Kugler, M. Tercelj

"The 1.2690 high alloyed tool steel is usually applied for cold working and is alloyed with carbide-forming elements Cr, V, W and Mo. It exhibits very poor hot deformability. Since there is no enough available data in literature for elucidation of this problem, hot workability and development of microstructure during hot deformation was studied. Hot compression tests were carried out in temperature range 850-1150 °C and strain rates range 0.001-6 s-1. SEM and OM were used for observation of microstructure. Results revealed very complex precipitation of carbides that depends on deformation temperature as well as on strain rate. It was found that especially at lower temperatures of hot working range the precipitation of carbides strongly depends on strain rate. Three different hot deformation behaviors’ were observed depending on temperature and strain rate range.IntroductionThe hot workability of highly alloyed high speed steels is usually described as relatively poor in comparison to other steels due to their tendency of cracking during hot working especially when inappropriate hot working conditions are applied. Alloying elements such as Cr, W, Mo and V in ledeburitic tool steels form carbides that improve hardenability, strength, hardness, wear resistance, etc., but they decrease hot workability and narrow hot working temperature range in comparison to conventional steels. The size, distribution, type and fraction of carbides, as well as the thermomechanical history of material and hot working parameters have major influence on the hot workability. The microstructure of ledeburitic tool steels during hot deformation can be characterized as a two-phase system consisting of an austenite matrix and a combination of ledeburitic carbides [1-4]. In the soft-annealed condition the total volume fraction of carbides is in the range 19-30% and in the quenched condition in the range 9-25%, depending on the chemical composition. During heating before deformation a large quantity of carbides dissolve, but non-dissolved carbides can have an extremely diverse influence on the hot workability due to variations in their composition, size, distribution, hardness and shape, and their different behavior during the deformation phase [5-7]."

Jan 1, 2011

By Mei Yang, Wei Gao, Jian Yang, Qingcai Liu, Wenchang Xi

"TiO2 has been loaded on cordierite porous ceramic to prepare the SCR catalyst carrier by using both APCVD and sol-gel technology. In APCVD method, TiC14 and O 2 were used as reaction precursor. TiC14 was gasified by using N2 as carrier gas which was controlled to 500sccm. Its reaction temperature and reaction time were limited to 773K and 30min respectively. The physical properties, SEM and SEM-EDX of the TiO2-cordierite carrier and the properties of SCR catalysts prepared by these carriers have been tested. The tests showed that TiO2 loaded by APCVD method were of graininess shape and even accumulation. The loading rate of TiO2 and the specific area of carrier sample were increased 114% and 21 % respectively comparing with sol-gel technology. In the result of sol-gel method, the maximal difference of Ti content was 66.92%, while the result of APCVD method was 18.89%. It demonstrated that TiO2 was uniformly attached with the cordierite ceramic by using APCVD method, which would ensure more active ingredients well loaded on the Ti02-cordierite carrier. This difference made the denitrification ratio of catalyst prepared by APCVD method was 8.1 % higher than that of catalyst prepared by sol-gel method.IntroductionIn recent years, the emission of NOx, which were caused by coal-fired power plants, has gotten more and more attention. SCR (selective catalytic reduction) is the most effective technology to DeNOx [ll. The core technology of it is the catalyst. The SCR catalyst usually uses Ti02 as the carrier, and V2O 5 as the active component [2, 3] . However, the thermal stability and mechanical properties of TiO2 carrier are unstable, which would influence the performances of the catalyst. The commercial catalyst generally uses WO3 or MoO3 to promote its heat stability at present [4-7] Besides, TiO2 is expensive. Compared with TiO2, the cordierite is of good thermal stability and lower price. So loading Ti02 on cordierite porous ceramic as carrier to produce SCR catalyst is of good prospects [S, 91 • Currently, TiO2 is usually loaded on cordierite by the sol-gel method. But some research has shown that the sol-gel method easily reduced the loading performances of TiO2, such as distribution, combination, etc. APCVD (atmospheric pressure chemical vapor deposition) has many advantages to preparing TiO2 films, such as high bonding strength, fast reaction rate and so on [l0-13l_ In this paper, TiO2 has been loaded on cordierite porous ceramic to prepare the SCR catalyst carrier by using both APCVD and sol-gel methods. The properties of the carriers prepared by the two processes have also been compared."

Jan 1, 2011

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Kellie Provazi

"The purpose of this paper is to study metal separation and recovery from a sample composed of a mixture of the spent household batteries main types, using liquid-liquid extraction and metals electroplating. The electrolytes preparation consisted: grinding the waste of mixed batteries, reduction and volatile metals elimination using electric furnace and acid leaching. From this solution were studied the liquid-liquid extraction using Cyanex 272 [bis(2,4,4-trimethylpentyl) phosphoric acid] with tributyl phosphate as extracting agent. After study of solvent extraction and stripping has been recover and separate the metallic ions and with electroplating was recovered the manganese, copper, nickel and cobalt in their metallic forms.IntroductionCurrently has increased the consumption of electronics devices such as mobile phones, laptops, wireless phones, comcorders, etc., especially portable devices that use batteries as a power source, and consequently has increased the disposal of such material.Increased consumption of this devices is caused by several factors including increased popularity of consumer electronics devices, has become essential of modem life. Therefore, recycling of batteries is important because its reduces the waste of raw materias and nonrenewable resouces used in manufacturing these materias and help prevent potential environmental risks associated with improper disposal of these products together with household garbage.The batteries have a very diverse composition, containing metals such as zinc, lithium, nickel, lead, mercury, cobalt, cadmium, iron, copper, manganese and rare earths. Some components may contain hazardous materials such as cadmium, mercury and lead, and can contain acids or bases.This research line is a pioneer in dealing with a single process for recycling a mixture with all batteries types, for only processes that exist in the world are based on the recycling a mixture with all types of batteries, for only processes that exist in the world are based on the recycling of one or two types of batteries [1-4]. This process necessitates the previous separation of the batteries by type."

Jan 1, 2012

By Jing Zhan, Tian-zu Yang, Wei-feng Li, Li-Hua Jiang, Shi-yan Xu, Jian-yang Huang, Chuan-fu Zhang, Yan-qing Fan

The amount and activity of coal, reduction temperature and other parameters of the process of bottom-blown reduction of liquid high lead slag were investigated in laboratory. Methods to strengthen the bottom-blown reduction process were studied by industrial production. The results were in the follows: the reduction temperature was 1150℃; reduction time was 1.5h; the reductant was anthracite; lead content in slag was controlled to 2%; the rate of coal was 7% and gasification loss of coal in high temperature was severe; liquid lead slag reduction rate was faster with coal; prolonging the reaction size had little effect on reducing lead in slag; the size of the reactor can be further reduced.

Jan 1, 2015

By Gong-yi Guo, Yu-li Chen

"A partially-stabilized zirconia powder was prepared by metalorganic precipitation process from technical-grade zirconium oxychloride and the effluent of an acrylic acid plant. The effluent contained low molecular weight carboxylic acids, i. e., acrylic acid and acetic acid. The· developed process is based on the selective precipitation of acrylic acid at suitable pH values by the addition of zirconium oxychloride to the effluent. The resulting precipitate is a precursor that can yield a pure, ultrafine, and partially-stabilized zirconia powder. The evolution of formation of the partially-stabilized zirconia in the present process was investigated using thermal analysis, infrared spectroscopy, and X-ray diffraction technique. Environmental, technological and cost advantages will make the present process feasible for manufacturing advanced zirconia ceramics.IntroductionIn recent years the superior mechanical, thermal, electrical and chemical properties of stabilized zirconia have become the focus of growing scientific and technological interest, and hence resulted in various structural and functional applications. The great potential of the material has given rise to numerous preparation approaches to obtain the material with the excellent properties; nevertheless, an extensive number of programmes are underway worldwide aimed at understanding and improving both the preparation and behavior of stabilized zirconia ultrafine powders. (1 – 8)."

Jan 1, 2000

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015

By Xirneng Zhu

The electrochemical behavior of Pittsburgh and Illinois coal pyrite in basic and neutral borate/sulfate solutions was investigated. In the transpassive region, aggressive oxidation of pyrite occurred. The reaction products in this region were Fe(III) oxide, sulfate ion and partially oxidized sulfur intermediates. The formation of sulfur and polysulfides was identified by in-situ Raman spectroscopy. The growth kinetics of the reaction product film, resulting from transpassive oxidation of coal pyrites, were studied using chronoamperometry measurement with both stationary and rotating disk electrodes. The reaction rate was well correlated by a paralinear rate equation. The effects of electrode rotation speed, solution pH and temperature were examined. The kinetics were compared to those for mineral pyrite.

Jan 1, 1994

By Patricia A. Wells

In the remelting of scrap, the ultimate goal is to produce clean aluminum while minimizing metal losses. Recently, it has become more difficult to make significant recovery improvements in Reynolds' Reclamation Plants since metal recoveries were nearing the theoretical maximum. In an effort to gain a better understanding of the factors impacting Reynolds remelting process, a series of experiments using a Taguchi-type design was performed. Specifically, the critical variables and interactions affecting metal recovery of shredded, delacquered Used Beverage Containers (UBC) melted in a side-well reverbatory furnace were examined. This furnace was equipped with plunger-style puddlers and metal circulation. Both delacquecing and melting processes operated continuously with downtime only for necessary mechanical repairs. The experimental design consisted of an orthogonal array with eight trials, each using nominal 500;000 lb shred charge volumes. Final recovery results included molten output and metal easily recovered from dross generated during the test.

Jan 1, 1995

By Du Sichen, S. Seetharaman, Wei Liu

"The viscosities of two-phase mixtures are of great importance in the modelling of the fluid flow in metallurgical processes. For example, in steel making and refining, the intimate mixing of metal droplets in the slag phase requires a consideration of the effective viscosities for the mixture. The present work was aimed at an understanding the phenomena underlying the viscous flow in a two-phase mixture with widely differing viscosities.Emulsions of silicone oils of known viscosities (345mPa.S and 1010mPa.S at 293K) with small amounts of water evenly distributed in the same were prepared by subjecting the mixture to uniform stirring using a magnetic stirrer. The viscosities of these emulsions were measured at constant temperature by rotating cylinder method using Brookfield Digital Rheometer. The uniformity of the preparation of the emulsions was confirmed by the reproducibility of the results. Th7 measured viscosities were generally found to be independent of the torque under the experimental conditions so that the two-phase mixture could be considered as a Newtonian liquid. The variation of viscosities with temperature and the effect of addition of a surface-active substance were also studied in this work.The measured viscosities were found to be· higher than those of both pure water and silicone oil. The experimental viscosities were found to increase with increasing concentration of water. The influence of surface tension on the viscosities was examined by adding surfaceactive agent to the mixtures. The result is discussed and compared with theoretical models developed by Einstein, Taylor and Oldroyd."

Jan 1, 2000

By L. Katgerman, R. Van Toi, H. E. A. Van den Akker

"Mould filling simulations are powerful tools for optimizing the characteristics of castings. The robustness of calculational methods for mould filling simulations is generally tested in simple geometries. While a vertical plate has been used often for validation studies, this paper aims at mould filling simulations of a horizontal thin wall casting. Such castings exhibit a strong interaction between heat transfer (solidification), surface tension and gravitational force.The results are presented of a study to validate numerical simulations of mould filling phenomena in a thin wall horizontal casting. Solidification during mould filling is studied computationally. Velocities are measured using Particle Image Velocimetry.INTRODUCTIONIn foundry practice Computational Fluid Dynamics (CFD) is being considered a promising tool to arrive at a better understanding of casting defects introduced during the mould filling period of a casting. The use of CFD is believed to be advantageous in predicting possible defect locations, pouring times, and the lowest possible casting temperature without the risk of cold shuts. In addition, CFD may be used to optimize pouring system geometries [1,2]. As opposed to experimental studies in, e.g., cold water models, CFD allows for the flexible modification of the casting geometry and the pouring system, and for the inclusion of physical effects such as solidification and heat transfer. Thus, a proper use of CFD may lead to a reduction of the casting rejection rate without expensive trial-and-error procedures, and to a decrease of production costs in foundries. Mould filling simulations take a special place in CFD, because a free surface tracking algorithm is required. Over the past decade methods, MAC [3] and SOLAVOF [4], have been extended to 3-D. The robustness of computational methods for mould filling simulations is generally tested in simple geometries [5,6]. While a vertical plate has been used often for validation studies, this paper concentrates at mould filling simulations of a horizontal thin wall casting. Thin wall horizontal castings exhibit a strong interaction between heat transfer (solidification), surfaces tension and gravitational force. The gravitational force in this setting is orthogonal to the plane of flow and has therefore no influence on the shape of the free surface in the plane of flow. Mould filling numerical methods and algorithms have been recently reviewed by Chen et al.[7]."

Jan 1, 1999

By Gudrun A. Saevarsdotti

For decades tile aluminium industry has been practicing gas treatment of aluminium melts. This treatment is of great importance because of its influence on 'impurity" and inclusion removal from the melt. The gas-melt interaction is greatly influenced by the gas composition, melt temperature etc. This paper gives an overview of the interaction between argon-chlorine gas mixtures and the aluminium melt. It covers the thermodynamics of the reaction between the chlorine and a number of different elements commonly found in liquid aluminium, and discusses the behaviour of reaction products in the melt. The paper reports an experimental study of the behaviour of the chlorine-molten aluminium interface, using sodium contaminated aluminium melt with and without the addition of grain refiner.

Jan 1, 1996

By Carlos G. Levi

"The principles involved in the rapid solidification of supercooled metal droplets and existing numerical models are reviewed. The limitations of these models for studying alloy solidification are discussed in terms of the effects of alloying elements on the relevant heat transfer, thermodynamic and kinetic parameters. Analysis of the enthalpy-temperature diagram reveals how the extent of rapid solidification is hindered by the addition of solute. A solidification model incorporating thermodynamic and kinetic relationships into a Newtonian heat transfer formulation is used to analyze the thermal history and concurrent solute redistribution during recalescence. IntroductionIt is well acknowledged that microstructural evolution during solidification is intimately associated with the thermal history of the liquid-solid interface. Structural parameters like chemical homogeneity, morphology and size scale of the phases can be related to the interfacial temperature and velocity. These in turn change by the interaction of the interface with the thermal and solutal fields in its neighboring environment.The thermal history of powder solidification can be conveniently described on the enthalpy-temperature diagram for a pure metal shown in Figure 1 and discussed in detail elsewhere [1). A system can conceivably follow any path of decreasing enthalpy in the supercooled region of Figure 1 (~ < 1), starting at the nucleation temperature (oN < 0) on the liquid line, and ending at some point on the solid line. A vertical path represents an isothermal transformation, of which a limiting case is solidification without significant barriers to nucleation and growth, with the interface at the equilibrium temperature TM (path one in Figure 1). A horizontal path represents isenthalpic (or adiabatic) solidification whereby the system could form an amount of solid proportional to the initial supercooling of the liquid without further heat loss to the environment. A liquid that can completely transform to solid under adiabatic conditions is said to be ""hypercooled""."

Jan 1, 1986

By Jerome P. Downey

The Indium Corporation of America - Colorado School of Mines Indium Separation Technology was evaluated as a potential means of treating smelter flue dusts stockpiled at the Pintlar Corporation property in Kellogg, Idaho. The patented technology represents a method for segregating the contained indium, lead, and other metals in forms acceptable for downstream processing and recovery. Separation is effected by treating the dust with metallic sodium in a bath of molten lead. Process effectiveness was measured by determining the relative distribution of key metals between the bullion and dross products at small pilot plant scale. The study indicated that application of the technology to the Pitlar samples results in a highly efficient concentration of lead in the bullion, while indium is collected in the dross. The distribution of other key metals between the bullion and dross products and the effect of varying selected process parameters are also discussed.

Jan 1, 1994