Search Documents

By Sarah Beutner Mavrogenes

The mineralogy of three slags from a domestic secondary copper refinery were studied by applied mineralogical techniques to determine the: 1) phases present, 2) phase chemistry, 3) phase abundance, 4) associations, 5) crystalline habit, 6) grain size, 7)microtextures, and 8) causes for certain metallurgical problems, such as metal losses to the slags. The slags were produced by skimming the bath prior to melt-down to allow heat from the flame to reach the bath. The first slag is highly viscous and all three slags contain a large amount of copper. The "first slag", which is skimmed prior to treatment of the bath with fluxes, contains metallic copper, cuprite, delafossite, magnetite, Mg-hercynite, common spinel-chromite solid solution, picrochromite-chromite solid solution, common spinel-picrochromite solid soiution, gahnite, cassiterite, silica-rich glass, and corundum. Its abundant solid refractory phases make the slag difficult to skim. The "soda-rich slag", skimmed after the treatment of the bath with sodium carbonate flux, contains cuprite, delafossite, magnetite, cassiterite, Na-Al-silicate, and Na-Al-Ca-silicate. It contains less metallic copper than the first slag and lacks the refractory minerals. The "phosphorus-rich slag", skimmed after treatment of the bath with a copper phosphide flUX, contains metallic copper, cuprite, delafossite, berlinite, cassiterite, silica, apatite, Cu-Fe-rich apatite, copper phosphate, Cu-Fe-phosphate, and a Pb-phosphate. In contrast to the above three copper-rich slags, recent charges have produced a silver-copper-rich slag. The "silver-rich slag", skimmed after the treatment of the bath with a copper phosphor ide-borax flux, contains, cassiterite, delafossite, cuprite, a Na-Al-silicate, magnetite, metallic copper, MgO, common spinel-chromite solid solution, and wollastonite. Silver ranging from 0.05 to 2.02% was found by atomic absorption and inductively coupled plasma spectrometry analyses in the metallic copper phase.

Jan 1, 1989

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By N. Menad

. Electronic wastes are heterogeneous mixture, with mainly copper, aluminium and steel attached to or mixed with various types of plastics and ceramics. In general, small amounts of precious metals are incorporated in this mixture. Today, these components constitute an environmentally problematic fraction in disposal. Their physico-chemical characteristics have been investigated through chemical, x-ray diffraction, infrared spectroscopy, scanning electron microscopy and thermal analysis.

Jan 1, 2000

By Richard S. Kunter

Artech Recovery Systems, Inc has developed a low pressure and temperature? leach process called the "Cashman Process" to extract metals from arsenical flue dusts and residues and fix the arsenic in an environmentally stable form as ferric arsenate (scorodite). The process was pilot tested at Hazen Research in an integrated plant including continuous recycle from August 1989 to October 1989 during which several tons of flue dust were processed. Based on this pilot program, the process was deemed technically feasible and produced commercially salable products. Residues from this pilot program were subjected to a long-term stability test jointly designed by PTI environmental services and the USEPA. The process, its versatility, and the nature of the products is discussed in some detail.

Jan 1, 1992

By Jorge Alberto Soares Tenório, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Franco Alves Lavacchini Ramunno

"The traditional process for recovery of metals from waste electric and electronic equipment (WEEE) usually involves pyrometallurgical processing. However, the application of this technology to processing waste printed circuit boards (WPCBs) might lead to the formation of dioxins and furans, due to thermal degradation of flame-retardants and polymeric resins present in the board substrate. Therefore, this paper proposes a hydrometallurgical route for the recovery of copper. The acid leaching behavior of copper has been investigated at three different temperatures (25°C, 50°C and 75°C) with and without the addition of an oxidizing agent (hydrogen peroxide - H202). The dissolution kinetics for acid copper leaching was calculated based on chemical analysis by ICP-OES (Inductively Coupled Plasma - Optical Emission Spectroscopy). At 50°C with 1 mol/L H2S04 added 10 mL H202 (30%) each half hour under pulp density of 1 g I 10 mL, 100% of copper was extracted after 3 hours. The dissolution kinetics of copper with H2SO4-H2O 2 followed 1 - (1 - X)113 =Ket, i.e. chemically controlled reaction model.IntroductionThe information regarding the generation of waste electric and electronic equipment (WEEE) are still difficult to obtain because the estimates should take into consideration the historical production and sale of various products and the rate at which they reach the end of their life cycle, whose duration depends on the behavior of consumers [1]. Thus, the estimated overall WEEE generation varies between 25 and 50 million tons each year, which corresponds to more than 5% of all municipal waste generated [2], and this amount will increase at a rate of 3 to 5% per year, approximately three times faster than other individual types of waste [3].Printed circuit boards (PCBs) are essential parts of electric and electronic equipment (EEE), being found in virtually all electronic products, as well as in weapons systems [4]. A PCB is a basic component, which consists of a board where copper tracks are deposited. While the board behaves as an electrical insulator, the tracks connect electrically the various components attached to the board [ 5]. In addition to glass fibers, paper and resins, the PCBs contain significant amounts of metals, such as copper, iron, nickel, lead, stain, silver, gold and palladium [6]. In general, the weight fraction of metal is around 28% and the remainder of the boards is composed of plastic (19%), bromine (as flame retardant - 4%) and ceramic material (49%) [7]."

Jan 1, 2014

By F. Tailoka

Microporous membranes have been used to create a very fine dispersion of bubbles which greatly enhances the mass transfer of electroactive species to the electrode. Using this system, it has been shown that it is possible to electrowin copper as a coherent planar deposit, at high current densities, from copper chloride solutions.

Jan 1, 1990

By J. D. Miller

Low-level radioactive contaminated soils (10-500 pci/gm) created by defense-related activities at certain superfund sites, such as Nevada Test Site (NTS), is a current environmental concern. Many of these contaminated sites may require appropriate cleanup and restoration, which could cost billions of dollars and put tremendous pressure on our limited financial resources. Therefore, the development of a selective flotation process to separate such radionuclides from contaminated soils should be considered. In this study, both a pure depleted UO2 sample and three synthetic UO2/soil mixtures were used to evaluate surface chemistry features and to examine the possibility for the flotation of fine UO2 particles from selected soils. It was intended that this model system would be a reasonable representation of contaminated soils such as those found at the Nevada Test Site which are reported to be contaminated by PuO2 fallout. The effect of reagent schedule, particle size distribution, and surface charge are discussed with respect to the flotation separation of the UO2/soil mixtures. It was found that both commercial fatty acids and reagent grade sodium oleate are effective collectors for UO2 flotation provided the pH is adjusted to the range of pH 8-9. The bench-scale flotation results successfully demonstrated that froth flotation technology can be used to remove UO2 from such model contaminated soils with appropriate flotation chemistry conditions which depend on the soil characteristics and other pretreatment procedures. In the best case, 90.2% of the UO2 was removed from a UO2/NTS soil mixture (119 ppm UO2) and the soil reduced in UO2 contamination from 119 ppm to 17 ppm in a single stage bench flotation. The impact of clay slimes present in the soil is revealed by the results which show that, for example, for a deslimed soil (28x400 mesh and 100 mg UO2/kg soil) 85¬90% UO2 recovery can be obtained with a reduction in contamination to 4.6 mg U02/kg soil.

Jan 1, 1995

By QIE Jun-mao, DONG Fang, DENG Hao-hua

The DIL402C thermal dilatometer and STA449C thermal analyzer were employed to test the linear expansion and contraction coefficient，CP and DSC curve of 304 stainless steel. The result showed that the linear expansion coefficient range was 20.9700×10-6～21.5712×10-6 and the linear contraction coefficient range was 21.2528×10-6～21.9471×10-6.The linear expansion and contraction coefficient were higher than other steel grade，so the 304 stainless steel belonged to the crack sensitive steel. Because of the crystal phase transformation occurred during the 1000~1400 ℃,the curve of CP fluctuated obviously and the defects of casting blank occurred easily. Chosen 1414℃ as the liquidus temperature of 304 stainless steel based on the analysis results of DSC. The curve of DSC was unsmooth during 1450～1100℃，the crystal phase transformation occurs and thermal stability of slab was inferior.When the initial solidified shell formed in this temperature range,the thickness of the shell would be nonuniform and the surface defects occurred more easily.

Jan 1, 2015

By I. D. Reznik

On blowing nickel matte in a converter without quartz, first the oxidation of metallic iron and a part of FeS occurs without evolving sulfur dioxide, the formed FeO dissolves in a sulphide smelt and form a homogeneous oxysulphide smelt. On further increasing the FeO content, the oxysulphide separates into 2 layers. Based on the laboratory investigation of FeO-(FeS+Fe°) - (Ni3S2+Ni°) ternary phase diagram we have identified the separation region at 1250°C. The boundaries of the separation region have the form of an arc and the composition of the separated oxysulphide layers is defined by the canodes. In the nickel or copper-nickel matte - silicacalcium oxide slag system at 1250°C three layers, namely sulphide, oxysulphide, and slag may be formed. A high slag basicity due to the presence of CaO can serve to enhance the activity of FeO; a low nickel content in the matte corresponds to a high concentration of FeS therein; FeO from slag and FeS from the matte form a homogeneous FeO-FeS solution, i.e. an oxysulphide layer. The investigation on the "Camebaks" apparatus and by the nuclear gamma-ray resonance spectroscopy method of the phase composition in a slowly cooled oxysulphide layer has shown the presence of four phases: wustite, troilite, ferronickel grains, and calcium oxide-silica inclusions. Knowledge of regularities in the oxysulphides formation makes it possible to use them in pyrometallurgy of nickel and cobalt or preventing their formation.

Jan 1, 1997

By J. R. Sarazin

Density driven convection during solidification has been recognized for some time to result in macrosegregation particularly when lower density alloying elements are rejected into the interdendritic liquid. The resulting segregates are commonly referred to as channels, freckles or A-segregates. Buoyancy driven convection leading to channel formation has been examined in three model systems possessing somewhat different materials parameters. They are the Pb-Sn eutectic system, the transparent aqueous-salt NH C1-H 0 4 2 eutectic system and the transparent organic succinonitrile-ethanol monotectic system. Convection in these systems is controlled by a balance of buoyant and viscous forces, which are strong functions of composition and temperature. Composition, temperature and flow velocity were measured and elimination of channels through heavier ternary additions is discussed.

Jan 1, 1991

By J. P. Evans

The modem copper smelter today utilizes tonnage oxygen for smelting concentrates, generating a high strength S02 off-gas leaving the smelter vessel. This gas stream, which also contains any unreacted oxygen, plus C02, N2 and H20, also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates. The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals in the off-gas circuit. Depending on this history, the type and characteristics of the chemical and physical reactions which. occur in the gas handling system can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries .and design, on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data, several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By J. P. Evans

The modem 'copper smelter today utilizes tonnage oxygen for smelting concentrates. ,generating a high strength S02 off-gas leaving the smelter vessel. This gas stream. which also contains any unreacted oxygen, plus CO2; N2 and H20. also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates, The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals, in the off-gas circuit. Depending on this history. the type and characteristics of the chemical and physical reactions which occur in the gas handling system 'can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries and design. on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data. several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By K. Narayana Swamy

Experimental results of 3-phase mixing in a physical model of a CCRL for metals refining, at high levels of bottom gas injection (up to a superfIcial gas velocity (Us) of 12.5 cm/min), are presented. A thermal tracer technique was used to elucidate both longitudinal mixing and interphase heat transfer. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing (D. < 20 cm2/s and D/uL < 0.1) in the CCRL. Interphase mass-transfer coefficients of the order of 0.02 cm/s and higher, are predicted from the measured interphase heat transfer coefficients using the mass and heat transfer analogy. Adequate performance is likely to be possible for an industrial CCRL, based on extrapolation of these results to full-scale conditions.

Jan 1, 1996

By Gervais Soucy, François Quesnel, Pierre Hovington, Wen Zhu, Karim Zaghib, Jocelyn Veilleux

The properties of lithium titanates anodes in Li-ion batteries are highly dependent on their secondary constituents. While their main phase is usually constituted of Li4Ti5O12, significant quantity of lithium titanates compounds of various stoichiometry are often present, due to either the processing, usage or aging of the material. These may go underreported, as many of these spectrums overlap or display low signal in X-ray diffraction (XRD). Samples of nanosized lithium titanates synthetized by inductive plasma were characterized by XRD and scanning electron microscopy (SEM), as they provide a regular yet typical crystallite size and shape including multiple phases. A Rietveld refinement was developed to extract the composition of these samples. Mass balance through further annealing and differential scanning calorimetry (DSC) enthalpy measurements from phase transformations were also used as identification and validation techniques.

Jan 1, 2015

By Bing Gao, Zhe Wang, Xiangdong Xing, Xueqi Zhang, Shan Ren, Jianliang Zhang

"In sintering, the flame front speed (bed permeability) and sinter qualities are greatly depended on the feed size, especially coke breeze and limestone particle size. It is well known that coke breeze provides sinter bed with heat to meet the demand of partial fusion and diffusion bonding while limestone reacts with iron ore to generate bonding phase in the sintering process. Accordingly, it is necessary to find the optimum combination of different particle size of coke breeze and limestone to yield sinter associated with better qualities. In this study, sinter was produced in the sinter pot with varying coke breeze and limestone particle size together in sintering of a coarse hematite iron ore. The sintering productivity was measured and all of the result sinters were examined by microstructure analysis and reduction degradation test (RDI test). For the sintering of a coarse hematite iron ore, it was found that the optimum mean particle size combination of coke breeze and limestone was 1. 71mm and 1.55mm in the sinter mix. On such a circumstance, sintering productivity was higher and the properties of sinter were better.IntroductionNowadays, as the main iron bearing burden material of modem blast furnaces, sinter has a great influence on the blast furnace operation. Sintering is a greatly complex process involving various chemical reactions to form kinds of mineral phases [1, 2]. In the sintering process, coke breeze is used for fuel and it generates heat to raise the green bed temperature. Limestone serves as flux and it reacts with iron ore to produce various mineral phases. On one hand, during the sintering process, the particle size of coke breeze can have an effect on temperature, atmosphere, the flame front speed and all of them act on the microstructure and mineral constitutions of sinter [3, 4]."

Jan 1, 2013

By S. Ozbilen, B. Erdogan, M. Erdogan

To study by thermal analyses the response of precipitation hardenable alloys of Al-Cu-Mg and Al-Li-Cu-Mg system to natural and artificial ageing, a series of ternary and quaternary Al-alloys with nominal compositions of Al-l.13wt%Cu-0:65wt%Mg (alloy-I), Al-1.15wt%Cu-0.57wt%Mg-0.07wt%Li (alloy-2), Al-l.19wt%Cu-0.56wt%Mg-0.75wt%Li (alloy-3), Al-2.0lwt%Cu-0.89wt%Mg (alloy-4), Al-2.14wt%Cu"0.56wt%Mg-0.07wt%Li (alloy-5) were used in the present investigation. Samples in the form of rolled sheets are subjected to water quenching at 25EC after solution treatment at 530EC for 20 min. Alloys were aged naturally at room temperature (25EC) up to 2 months and artificially at 190EC up to 2 days. By using differential scanning calorimetry (DSC) in the temperature range of25-300EC, differential thermal analysis (DTA) in the temperature range of25-600EC together with Vicker's hardness measurements, the response to natural and artificial ageing of the alloys used in the present study were investigated. It was observed that in these alloys, GPB(Cu, Mg) zones [Guinier-Preston zones with Cu and Mg] do form during water quenching at 20EC following solutionizing heat treatment. Natural ageing of the same alloys causes formation of more GPB(Cu, Mg) zones, which results in hardening in the alloys. Artificial ageing at 190EC up to l day results in GPB zone dissolution causing preliminary decrease in hardness values while two days of artificial ageing in the alloys cause S' (Al2CuMg) precipitation confirmed by DSC/DTA analyses resulting in an increase in hardness values. Li addition up to 0.75wt% helps T1 (Al2CuLi) and T 2 (Al6CuLi3) phase formation together with S' precipitation as DSC/DTA analyses show after the same heat treatment.

Jan 1, 1998

By D. J. Senor

Closed chamber incineration (CCI) is a novel technique by which irradiated nuclear graphite may be destroyed without the risk of radioactive cation release into the environment. The process utilizes an enclosed combustion chamber coupled with molten carbonate fuel cells (MCFCs). The transport of cations is intrinsically suppressed by the MCFCs, such that only the combustion gases are conducted through for release to the environment. An example CCI design was developed which had as its goal the destruction of graphite fuel elements from the Fort St. Vrain reactor (FSVR). By employing CCI, the volume of high level waste from the FSVR will be reduced by approximately 87 percent. Additionally, the incineration process will convert the Sic coating on the FSVR fuel particles to SiO2, thus creating a form potentially suitable for direct incorporation in a vitrification process stream. The design is compact, efficient, and makes use of currently available technology.

Jan 1, 1994

By H. M. . van der Donk

In this work an overview is given about the techniques available for the removal of metallic impurities from molten aluminium. The overview is focused on the removal of iron. Also, some experimental results are given about the creation of iron-rich intermetallic compounds in an aluminium system, which are subsequently removed by gravity segregation and filtration techniques. This work is part of an ongoing research project of three major European aluminium companies who are co-operating on the subject of recycling of aluminium packaging materials recovered from household waste by means of Eddy-Current techniques. Using this technique the pick-up of some contaminating metals, particularly iron, is almost unavoidable.

Jan 1, 1995

By Fuming Wang, Xin Lu, Hao Bai, Hebin Zhu

"In this study, CO2 emissions and carbon footprint of a typical steel works with integrated process and iron and steel industry in China was calculated and analyzed by a carbon footprint method based on the model of process CO2 emissions in iron and steel making. The carbon footprint of iron and steel industry from 1991 to 2010 in China showed a rapid increasing tendency. In 2008, the CO2 emissions of iron and steel industry in China was 1.289 billion tons, 19.71% of the national total CO2 emissions, and the corresponding carbon footprint was 159.13 million hm2 of green area. Carbon deficit of iron and steel industry also go up gradually if considering the carbon storage by green vegetation. Thus, the internal carbon reduction strategy, such as energy structure optimization and energy saving technology, was mainly encouraged for the sustainable development of iron and steel industry in China.IntroductionThe Global Warming resulting from the increase of Greenhouse Gases (GHGs), in particularly CO2, in the atmosphere has become the main reason of global climate change, and large emission reductions are required for sustainable development [ 1]. The iron and steel industry is the largest energy consuming manufacturing [2] in the world and the largest emitter of CO2 emissions. In 2005, it accounted for about 20% of global industrial energy use and 30% of energy and process CO2 emissions from industry [3]. In China, the crude steel has firmly been ranking at first of the world recent years and kept growing tendency year by year. With the production growth, the CO2 emissions of iron and steel industry also increased significantly and hence the steel industry has become one of the most sources of CO2 emission in China [4], which has attracted more and more attention to seek the carbon reduction strategies.Carbon footprint is an important and useful concept originating from Ecological Footprint, which was used efficiently to quantitatively analyze the impact of the human activities on ecological system, in particularly impact of the human energy activities [5]. In the view of Life Cycle, the carbon footprint is efficient to analyze the direct and indirect CO2 emission in the whole life of various products used in human activities. As to the iron and steel, the important materials and products in the human life, the carbon footprint analysis is quite necessary to evaluate the CO2 emission impact on the corresponding ecological system and global environmental."

Jan 1, 2013

By D. A. Horne, V. R. Daiga

Certain steel mill wastes contain significant amounts of zinc oxide due to the use of galvanized scrap during the steel making process. Typically electric arc furnace (EAF), and basic oxygen process (BOP) flue dusts contain 20 to 30% zinc oxide and 40 to 50% iron oxides, along with smaller quantities of lead and cadmium. These materials can be recovered from the flue dusts by using a proven rotary hearth furnace (RHF) process. By-products of the recycling operation include a crude zinc oxide fume, which is captured in a baghouse filtering system, and sponge iron that may be recycled into the steel making operation. Crude zinc oxide properties plus the operating experience from two commercial RHF installations utilizing MR&E's DRyIron™ Process will be presented.

Jan 1, 2000