Search Documents

By Zhenjun Tan, Lei Zhang, Jigang Li, Yifang Zheng, Jilai Xue

"Water electrolysis in 0.4 mol/L NaOH solution for hydrogen generation was carried out with ultrasound introduced through the anode. It was found that the cell voltage reduced by 150-300 mV in the current range of 20 mA to 40 mA with ultrasound frequency at 25.3 kHz. The cell operation became unstable when the cell current was larger than 75 mA with ultrasound. This reduction in cell voltage was due to removal of the gas bubbles on the electrode surface, which can be directly observed in the see-through cell of water electrolysis. Ultrasound with frequency of 33.3 Hz was also tried, but no better effect was obtained. The results suggest that ultrasound assisted water electrolysis can have potential in energy savings for hydrogen production.IntroductionIn electrolytic process, the electrode that the bubbles generated on its surface usually covered a thin gas film, which can be caused an additional voltage about 0.15-0.25V[l,2], especially in aluminum electrolysis. To solve the problem, loading the ultrasound removes the gas bubbles from the electrodes, this subject had been researched in recent years. From 1995 Jilai Xue et al[3,4,5]. applied the ultrasound in aluminum electrolysis in lab. The results from Sheng-De Li et al.[6] reveals that can decrease the cell voltage and have influences about the hydrogen and oxygen's output ratio. Although there are many paper about the applying of ultrasound such as in electrolysis[5,6], deposition[7,8], plating[9,10], oxidation of salts substance on the surface of electrodes[l 1] and so on, the effect of different frequencies ultrasound hadn't been investigated deeply.We focus on the anode voltage by different frequencies ultrasound and the bubble behaviors in this paper. The environment of this experiment is in alkaline solution. Through this exploration it can offer a basis for the applying of ultrasound in electrolysis."

Jan 1, 2011

By M. S. Moats

Galvanic stripping, in conjunction with solvent extraction, has been proposed as a technical option to the challenging problem of iron removal in certain hydrometallurgical processes. The galvanic stripping process is based on the ability of a solid metal to directly reduce ferric ion to the ferrous state in an organic media. Stripping the iron into the aqueous phase is then easily accomplished. Previous work has shown the reaction kinetics and efficiency are affected by such operating parameters as water and oxygen contents, temperature, time and metal reductant. In this study, the optimum operating range for some of these variables was determined. Both zinc and iron metal were used in the separate stripping of iron from D2EHP A. Reasons for the differences in the extent of the reaction obtained using the various conditions are discussed.

Jan 1, 1996

By T. Ranki-Kilpinen

In the flash smelting technique, developed by Outokumpu Oyj, off-gases with dust load are directed into the heat recovery boiler (HRB). As the temperature decreases, metallic sulphates become thermodynamically stable. Sulphation of oxidic particles initiates. The release of heat causes an increase in particle temperatures, and soft sulphated particles can stick to the heat transfer surfaces. Dust accretion may form and cause operational problems. The objectives of the project are to study sulphation reaction mechanisms and kinetics of flue- dust particles under HRB conditions, and get more information for the flue-dust treatment possibilities. The sulphation behaviour of synthetic Cu2O particles (37-53 pm) was studied using a fluid-bed reactor of laboratory scale. The experimental parameters in the latest campaign were oxygen and sulphur dioxide contents of 2.5-10 vol-% 02 and 40-60 vol-% SO2 respectively and temperatures of 600-660°C. Samples were examined microscopically (SEM+EDS) and chemical analysis were conducted. The sulphation rate was found to have a maximum at the certain temperature, which was dependent on the gas SO2 content. Regardless of the level of SO2, a rise in oxygen content promoted sulphate formation.

Jan 1, 2002

By L. A. Bertram, F. J. Zanner

"The goal of this paper is to present a tool to simulate transient melting of the electrode tip. This capability is needed to develop and test furnace control algorithms since experimental determination is difficult and expensive. Simulation incorporates parameters (including arc voltage, arc current, electrode gap and furnace pressure) from previous quasi steady experiments with 460 mm diameter Inconel 718 electrodes.Cathode heating rates (determined by classical as well as experimental arc models) are linked to these independent variables. After radiative loss adjustments to the heating, transient one dimensional melting is computed. IntroductionThe vacuum arc remelting (VAR) process attempts to improve the physical and chemical homogeneity of a static-cast electrode by remelting and solidification in a quasisteady manner. To achieve steadiness of furnace operation requires automatic controls based on inputs measuring physically relevant state variables of the process. Previous industrial scale VAR studies (1,2,3) involving stainless steels, superalloys, and other alloys have provided a basis on which control strategies of some generality can be proposed (4). Of these measurements, the data for Inconel 718 is the most complete, so discussion in this paper is restricted to this alloy.Studies of the In 718 alloy subjected to the VAR process have established that melt rate M (kg/hr) depends not only on the melt current 1m (kA) supplied to the furnace, but also on ambient gas pressure of CO, PCO (micron), and electrode gap ge (mm) as well (1):"

Jan 1, 1986

By Dale W. Collins

The disposal of arsenic from copper operations possess various health, environmental and processing problems. There are basically two areas of concern. The first being the disposal or treatment of smelter flue dusts and the second the removal of arsenic from refinery electrolytes. A number of treatment options have been proposed including the addition of soluble arsenic wastes to copper heap and dump leaching solutions. This approach will allow arsenic to be reintroduced to the ore via Solvent Extraction (SX) raffinate associated with hydrometallurgical operations. Knowledge of the attenuation behavior and mechanism during leaching is important in determining the long term stability of arsenic and the success of this approach. Parameters, such as uptake capacity, pH, particle size and solution chemistry have been investigated. Arsenic attenuation has been examined using column leaching with experiments employing both continuous flow and pulsed additions of As(V). In the initial stages of leaching, the attenuation of arsenic appears to depend on the pH and iron concentration in the effluent. Arsenic stability in the copper oxide ore has been examined with rinses of progressively lower pH.

Jan 1, 1994

By A. C. Wadhawan

In the present context of rapid industrialization, production of Lead-Zinc metals from low grade materials, residues and wastes can make substantial contribution to the supply of these metals in India. Recovery from secondary sources also plays an important role in conservation of mineral resources and lower power consumption. Conscious effort is therefore, required to increase the secondary metals which, besides saving in energy cost will also help in waste material management and keeping environment clean. The major thrust is, therefore, needed in this direction. During all these years, the Indian Lead- Zinc industry has made sustained efforts for recovery of metals from low grade ores and from metallurgical wastes and residues. The paper identifies the treatment of low grade ores by various technologies and techniques and the treatment of metallurgical residues and wastes generated during primary Lead and Zinc smelting in India. Some of the major achievements in past decade have also been elaborated in the paper. The strategies to be followed for continuing treatment of low grade ores and waste materials by adopting newer, environmental friendly technologies, in consonance with the rigid standards being adopted by most of the countries including India. have also been dealt with in the paper.

Jan 1, 1994

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature' in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By Joseph Hamuyuni, Pekka Taskinen

We present experimental results for the liquidus in the system Cu2O - CaO -Al2O3 at 1250 oC. In this study, we quantified the liquidus by the equilibration/quench/analysis technique, with Cu2O, Al2O3, and CaO as primary materials exclusively. Experiments were conducted in air at an at oxygen pressure (p) = 21.3 kPa). Equilibrated specimens were quenched in brine solution of 10 wt% NaCl. We then quantified the liquid chemical compositions by means of Energy-Dispersive X-Ray Spectroscopy (EDS) and Electron probe micro-analyzer (EPMA). This study reveals inconsistences in liquidus surface of the present ternary diagram of the system here in mentioned. Differences of up to 10 wt % compositions of the species have been observed.

Jan 1, 2015

By Takuya Shinagawa

After vitrification of the residues from a municipal solid waste incinerator, the vitrified products can be used as a construction material, and the dust can be used as raw materials for the non- ferrous industry. The NKK electric-resistance furnace is operated under a reducing atmosphere, and heavy metals such as zinc and lead in the ash vaporize to form dust. Also, dust from the NKK electric-resistance ash melting furnace is composed of water insoluble zinc and lead components and water soluble NaCl and KCI. This is why, The concentration of zinc and lead in the dust after washing is sufficiently high for the dust to be used as a raw material for the zinc and lead industry. NKK developed a heavy metal recovery process in which zinc and lead in the dust are reclaimed as a raw material for smelting by making the best use of the characteristics of the dust.

Jan 1, 2002

By I. J. Moon

The reduction behavior of hematite by H2 and H2-CO gas mixtures was investigated to elucidate the reduction mechanism at 800-950 °C. The hematite compacts were made by Cold Isostatic Pressing to produce compacts of uniform shape and size. The compacts were sintered at 1000° C for 30min, and showed a contraction of 29%. Mercury pressure porosimeter was used for measuring the total porosity, pore size distribution and pore surface area of the compacts. Reduction was measured by means of weight-loss technique using Cahn Balance (Model : TG-171, capacity log, accuracy f 10pg). Microscopic examination and X-ray analysis were used to correlate the structure of reduced compacts with the mechanisms of reduction. Neither chemical reaction control nor diffusion control is adequate in describing the complete course of reduction of the hematite compact. The reduction of hematite compacts was initially controlled by the chemical reaction at oxidelmetal interface. The reaction goes through a transition phase .where it is undergoing a mixed control, followed by the diffusion control towards the end of the reduction. The values of apparent activation energies for chemical reaction control were 3.48-8.43 kcal/mol depending on the gas compositions.

Jan 1, 1997

By M. Hashimoto

The equilibrium distribution ratios of sulfur between molten copper and CaO-fluxes containing caF2 and caC12 were determined in the range of 1300° to 1400° C under carbon monoxide. The rate of approach to equilibrium is rapid and increases with increasing CaCll concentration. In CaO-CaFl-CaCl2 fluxes, the distribution ratio varies in a complex way with temperature and CaFl concentration. The results are compared with those obtained with the binary fluxes of CaO with BaFZ and MgFl ?

Jan 1, 1983

By Run-bo Wang, Zhe Wang, Fan-yi Meng, Jian-Liang Zhang

The influence of semicharcoal substitution for coke breeze on sintering performance was investigated by pot-grate sintering test. At a fixed fuel ratio, sinter productivity and strength decreased with the substitution increasing from 0 to 100% due to better combustibility. To enhance the utilization efficiency of 100% semicharcoal, sintering parameters (moisture and suction pressure) was adjusted. With the moisture increasing, sinter performance of 100% semicharcoal increased because of the suppression of semicharcoal incomplete combustion. As the moisture further increasing to 9.0%, sinter quality gave rise to a decrease trend. The results also showed that the increase of suction pressure was benefit for the increase of heat transfer rate, leading to the improvement of heat utilization energy. Measures to enhance magnetite oxidation during sintering are discussed based on current understanding of the fundamentals that control the sintering process.

Jan 1, 2015

By Vladimir Mindin

This paper presents results of thermodynamic investigations and experimental' studies of some essential for pyrometallurgy of sulfide concentrates topics. Among them: 1. Thermodynamic simulation and experimental investigations of roasting process, 2. Thermodynamic investigations of sulfur dioxide off-gases treatment technologies. 3. Investigations on "Mind in -Kiknadze" effect of suppression of sulfur dioxide formation during sulfide concentrates roasting in the vapor containing atmosphere. 4. Thermodynamic simulation and experimental investigations of sulfide concentrates and manganese containing materials co-roasting processes. Some essential aspects of thermodynamic simulation techniques are also discussed.

Jan 1, 1998

By Zhucheng Huang, Ronghai ZHONG, Liangming Wen, Tao Jiang

The reduction roasting-magnetic separation and its strengthening of high silicon coal-containing mini-pellets by sodium additives were researched. The results show that the carbon gasification reaction and reduction of fine hematite in high silicon coal-containing mini-pellets with 3% sodium additives were enhanced. Comparing with no sodium additives, the gasification rate of carbon with 3% sodium additives reacting with CO2 for 40 minutes at 950 and the metallization rate of reduced pellets with 3% sodium additives after roasting for 35 minutes at 960 increased from 35.15% and 58.72% to 86.98% and 86.15%, respectively. The analysis of SEM equipped with EDS demonstrates that the inner pore of reduced pellets with 3% sodium additives was more developed and the iron grains size significantly enlarged, meanwhile, the iron grade of concentrate increased from 60.45% to 80.23% and the iron recovery rate decreased from 84.67% to 80.78% after grinding-magnetic separation.

Jan 1, 2016

By James E. Simpson, Suresh V. Garimella, III de Groh

"An experimental and numerical study of the horizontal Bridgman growth of pure succinonitrile (SCN) and of a succinonitrile-1.0 mol. % acetone alloy (SCN-1.0 mol. % ACE) has been performed. Experiments at growth rates of 0, 2 and 40 µmis were investigated. The solid/liquid interface was stable (non-dendritic and non-cellular); however, it was not flat. Rather, it was significantly distorted by the influence of convection in the melt and, for the growth cases, by the moving temperature boundary conditions along the ampoule. For the alloy, the interface was determined to be unstable at growth rates greater than 2.8 µmis, but stable for the no-growth and 2 µmis growth cases. When compared to the pure SCN interface, the alloy interface forms closer to the cold zone,· indicating that the melting temperature has been suppressed by the addition of the alloying element. Two-dimensional computer simulations were performed for the no-growth case for both the pure and alloy materials. These simulations indicate that a primary longitudinal convective cell is formed in the melt. The maximum magnitude of velocity was calculated to be 1.515 mmls for pure SCN and 1. 724 mm/s for the alloy. The interface shape predicted by the computer simulation agrees well with the experimentally determined shape for the pure SCN case. In ongoing work, numerical simulations of the process during growth conditions are being performed.IntroductionIncreasingly, advanced materials used in the aerospace, automotive, optics and electronics fields require low levels of defects and high levels of solute uniformity. Directional solidification by the Bridgman process is widely used for synthesis of these high-quality materials. During Bridgman crystal growth, heat and mass transfer by both thermal and solutal gradient-driven convection and diffusion influence the shape of the solid/liquid interface and dopant segregation levels, and hence, directly determine the final crystal quality. Key process parameters include the applied furnace temperature distribution and rate of translation, ampoule properties and furnace orientation."

Jan 1, 1999

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By Jie Li, Zhongliang Tian, Xun Hu, Kai Zhang, Yanqing Lai, Hongliang Zhang

The Al-Sc Alloys show many advanced properties for a wide range of engineering applications. But the metal Sc must be added into the metal Al in the form of the Al-Sc master alloy, which is usually produced by the thermal reduction process. In this paper, the decomposition voltages of Sc2O3 and Al2O3 in Na3AlF6-K3AlF6-AlF3 melt were calculated based on the Nernst equation. And the Al-Sc master alloy was prepared in the melt at 950°C by electrolysis. The results show that the Al-Sc master alloy can be prepared by the co-deposition of Sc3+ and Al3+ at the cathode if the concentration ratio of Sc2O3 to Al2O3 in the melt is more than 2:1 under the condition of the aluminum electrolysis. SEM and ICP analysis of the product indicates that the Al-Sc master alloy is made of the phase Al and the phase Al3Sc.

Jan 1, 2016

By Clemens Schmetterer, Patrick J. Masset

"The surface tension represents an important property for the modelling of high temperature processes. In this study the surface tension of two Al2O3 – CaO – SiO2 model slags and the influence of the admixture of 5 up to 30 wt.% FeO were studied. The surface tension measurements were carried out using the sessile drop technique on BN substrates under Ar atmosphere (10-6 atm O2) up to 1500 °C.IntroductionThe aim of VIRTUHCON1 is the virtualization of high temperature conversion processes, a task that requires thorough understanding of these processes. In many of these conversion processes slag plays an important role to control the properties of the product, to protect the reactor lining or simply as waste. Slag surface tension is one of the materials properties that is needed for the description of such processes, since it influences the interactions between the components in the reactor, e.g. at the slag – Fe interface in the blast furnace.Surface and interfacial tensions have thus received considerable attention in research, but the number of investigations in this particular pseudo-quaternary system is surprisingly low. Furthermore, the literature data are subject to different measurement conditions and techniques which complicates the data analysis and comparison.The slag atlas [1] offers a compilation of the available literature until 1986 (shown in Table I), but literature search has not revealed more recent studies of this system until now. For example, Elliott and Mounier [2] determined the surface tension of ACSF slags using the double tube maximum bubble pressure technique at 1200 °C. They kept their slags in contact with Cu-S-F mattes, and the slag therefore contained a certain amount of sulphur which acts as a surfactant and lowers the surface tension. The compositions of their slags were scattered over a wide composition range and they did not use a common ACS base mixture for their tests, either. The surface tension values vary between 417 and 446 mN/m, but due to the reasons just mentioned no trend in the measurements can be observed and the influence of FeO admixture on the surface tension cannot be deduced. Further information including the temperature dependence is available from Pavlov et al. [3], Ishchanov and Shushkov [4] and Murav’eva and Kaplun [5]; the diagram on page 446 in Ref. [1] has been drawn from these sources. Both positive and negative temperature coefficients are reported in these works. SiO2 is the only pure constituent that has a positive temperature coefficient [6], but a correlation of the temperature coefficient with the SiO2 content was not found to be conclusive."

Jan 1, 2011

By G. A. Irons, D. Colbert

Several electric arc furnace (EAF) shops have increased the zinc and lead grades of EAF dust by reinjecting it into their furnaces; however, the kinetics of this operation are poorly understood. To understand the kinetics, EAF dust was injected into 70 kg heats of iron or steel in an induction furnace. Supplemental additions of carbon and oxygen to overcome the heat load on the system were also investigated. In all cases, the dust was chemically transformed, and the zinc content increased from 16% Zn to 60 - 80% Zn. About 50% of the zinc in the EAF dust dissolved in the iron or steel. The zinc oxide in the dust is thought to be reduced by carbon and the zinc vapour subsequently dissolved in the iron. A kinetic model for the dissolution process is proposed, and the implications for EAF dust recycling are discussed.

Jan 1, 2000

By Chengxian Lui

Detailed mineralogical and metallurgical investigations were carried out on a phosphorous-bearing manganese carbonate ore from the Huayuan manganese mine, Hunan, China. Microprobe analyses indicate that the Manganese occurs mainly in calc-rhodochrosite and in rhodochrosite. The cOll&apos;pOsitional range of these manganese carbonate minerals is 50 -80 % MnOJ3, 0 -35 % CaOJ3, 5-35 % MgC03 and 0 -15 F~. The manganese carbonate minerals are very fine grained, IOOSt are between 4.6 and 9.4 1m in diameter. The small grains are clustered into aggregates that form bands 0.5 to 10 rnn wide. The phosphorous-bearing mineral in the ore is fluorapatite and is in grains that are generally smaller than 6 1m in diameter. Metallurgical tests show that it is possible to concentrate the aggregates of manganese carbonate minerals by high intensity magnetic separation, and to reduce the phosphorous content by rpasting the concentrate to convert the manganese carl::x>nates to insoluble hausmannite, and then leaching the roast product with HCI to dissolve the fluorapatite.

Jan 1, 1989