Search Documents

By Zhenbo Zhao

The processes and equipment for INLRFH (Isothermal Normalizing by Utilizing the Residual Forged Heat) of alloy carburizing steel products are presented. It is shown that four key parameters: namely (I) cooling rate before isothermal normalizing, (IT) the lowest cooling temperature before isothermal normalizing, (111) isothermal normalizing temperature and (IV) isothermal normalizing time, should be controlled. The prediction and calculation of these parameters can be achieved on the basis of components treated and the technical requirements of the steel parts by an on-line expert system. The cost-reductions due to the energy savings resulting from implementing this system for automotive parts heat-treatment are most promising.

Jan 1, 1999

By Cesimiro Fabian

The crystallite size of copper electrodeposits was determined by X-Ray powder diffraction analysis using a General Area Detector Diffraction Solution (GADDS) diffractometer. Crystallite size was calculated for copper thin films which were deposited on a 316 stainless steel rotating cylinder electrode (RCE) in the presence and absence of additive ?A?. The crystallite size was calculated from a corrected full width at half maximum (FWHM) of the [110] peak profile using the Scherrer equation. The test of significant difference on crystallite size was derived using Kruskal-Wallis method. It was found that in the absence of the additive the median crystallite size was 426, which decreased to 364 in the presence of the additive. As the additive degraded, the crystallite size increased to a size similar to that observed in the absence of additive.

Jan 1, 2003

By Denise C. R. Espinosa

Rechargeable lithium batteries are one of the most promISIng technology in battery development. Although Li ion batteries have been used as an alternative to the more polluting and less performing Ni-Cd batteries, Li ion batteries have limited life and their disposal is uncertain. It is imperative that valuables from wastes, such as lithium, should be recovered. The main objective of the present work was to characterize secondary lithium batteries for cellular phones. This was done using unit operations of mining processing, x-ray diffraction (XRD), chemical analyses and the rmogravimetric analysis (TG). The unit operations were hammer mill grinding, knife mill grinding, size separation and magnetic separation. After the hammer grinding process, the plastic cases were almost intact, however, they have released the cylindrical lithium batteries themselves and these parts correspond to 70% of the total battery weight.

Jan 1, 2001

By Aert Driessen

Australia has large resources of rare earths -- 4.35 Mt of contained rare-earth oxides (REO) in the demonstrated category and 1.69 Kt in the inferred category. Australia's demonstrated REO resources are contained in about equal proportions in placer deposits, which also host Australia's titanium and zircon resources, and in hard-rock deposits. The largest single deposit of rare earths, at Mount Weld in Western Australia, is contained in regolith overlying a carbonatite pipe. It has a demonstrated resource of 1.73 Mt of contained REO and yttrium oxide. The largest demonstrated resources of REOs in placer deposits are in the Murray Bash, southeastern Australia -- a total of 1.90 Mt of contained RE0 in six deposits. However, the REO-bearing minerals (monazite and xenotime) are of secondary importance and their recovery will be determined by the market for titanium dioxide and zircon. The Murray Basin and other pre-Pleistocene basins offer the greatest potential for discovering more REO resources. Australia produces about 7000 t/year of REO in monazite and xenotime nearly all from Western Australia, as by-product of mineral-sand mining; monazite production is about 12 000 t/year (6600 t REO) and intermittent xenotime production is about 50 t/year (25 t REO). About 8000 t/year of monazite containing about 4400 t REO is not recovered separately, or is lost in tailings, as is an unknown but smaller amount of xenotime.

Jan 1, 1992

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

By C. J. Malek

The CONTOP® smelting cyclone technology is a large-scale and time-proven method which in combination with other technologies (grinding, drying, pyrolysis, etc.) provides for a cost- efficient and ecological disposal of a wide range of waste materials from industry and households. In this report the basic principle of smelting cyclone technology will be explained first. Subsequently, the paper will discuss substantial concepts for the recovery of various remainders.

Jan 1, 1996

By Andre L. De Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals, from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal, plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS) Biologically produced hydrogen sulfide has economically very interesting, application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less-than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals,, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine, a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By E. Fregeau-Wu

The mineralogy and grain size distribution of phases in a steelmaking slag and experimental products from the heating of the slag under various conditions were determined to explore the possibility of recycling of the iron and manganese to the blast furnace. The steelmaking slags consisted of three major phases: dicalcium silicate, dicalcium ferrite, and Mg-Mn-wustite. Most of the phosphorus was contained in the dicalcium silicate and to lesser extent in the dicalcium ferrite. Due to the fine grain size of the dicalcium silicate, grinding and magnetic separation required pretreatment to increase the grain size and hence the liberation. Experiments on a steelmaking slag were conducted by heating the slag to 1633-1748°K( and slow-cooling in an inert atmosphere at various rates with or without the addition of fluorspar (CaF2) as a flux. Grain size distribution analyses of the starting material and the slow-cooled products were performed using the SEM-IPP area scan method and the QEM*SEM linear scan method. Comparable and reproducible results were obtained on the same sample using both methods. A size versus volume percent plot showed the increased grain growth most effectively. Examples of the grain size distributions obtained were used to show that a higher soaking temperature prior to slow-cooling, a slower cooling rate, and the addition of fluorspar to the slag promoted grain growth.

Jan 1, 1989

By K. Nona C. Liddell

There is a significant amount of early work that has been largely forgotten that deals with the validity of the pseudo-steady approximation for liquid-solid reactions. Much of this was originally published in the chemical engineering literature but is highly relevant to hydrometallurgical processes. The purpose of this paper is to summarize some criteria that were been developed by various authors for determining the error associated with use of shrinking core models for liquid-solid systems.

Jan 1, 2002

By Kumar M. Lyer

Residence time distribution (RTD) of light and heavy liquids in a pyrometallurgical channel reactor was mathematically modeled by representing the reactor as a combination of ideal reactors. Cold model studies simulated the counter-current flow of slag and matte (or metal) with high-strength bottom gas injection. The experimental variables include flow rates, heights, density and viscosity of the two liquids; gas flow rate; injector diameter; and distance between injectors. The experiments covered a wide range, of the appropriate dimensionless parameter, including conditions in ferrous and nonferrous extractive metallurgy. Dispersion modeling studies were also carried out to determine the degree of backmixing. Results indicate that the degree of backmixing in the channel reactor for various operating conditions corresponds to that for 3-20 perfectly mixed reactors in series.

Jan 1, 1993

By Anette Mueller, Thomas Schnellert, Sérgio C. Angulo

"The use of automatically sorting technique, to separate gypsum components from recycled material of processed construction and demolition waste (C&DW), is motivated by environmental and economical aspects. Only if the gypsum can be separated the aggregates can fulfill the environmental requirements and also the structural characteristics according to the standards. Furthermore, the separation of red brick can also improve the quality of the aggregates.This paper aims at analyzing the separation of gypsum components and red brick by using the color sorting technique. The impacts on the composition and the envelope density of recycled aggregates are described. Depending on the gypsum content the application of two processing stages (rougher-cleaner) can be necessary to produce aggregates with sufficiently low gypsum content. Additionally, the separation of red brick and concrete is successful. So, the color sorting may be a promising technique to upgrade the quality of mixed C&DW aggregates.IntroductionConstruction and demolition waste (C&DW) is a mixture of different materials. Such mixtures can be used only in low grade applications. If the material is used as certified material for road construction or as aggregate in concrete the concrete particles must be separated from the other building materials. This paper aims at analyzing the separation of gypsum components and red brick by optical sorting. The needed stages of sorting for getting a product quality according to the German Standards are deduced.Gypsum is a building material that is increasingly used for interior works in Germany like it is shown in figure 1 [1]. At present the content of gypsum in C&DW is estimated at about 1 %. Assessments on the basis of material streams of gypsum and concrete and their life spans show that higher gypsum contents of about 3 % must be expected in future [2]. Also in other countries the use of gypsum has grown considerably in the last decades. From the characterization of C&DW available in some cities in Brazil, 4 to 15 % of total amount of C&DW that may arrive at the recycling plant to be processed is excessively contaminated by gypsum. In one of these cities, the average content of gypsum in the C&DW before processing was as high as 2.1 % [3]."

Jan 1, 2008

By Mathilde Guilpain

A wide variety of plants are able to extract nickel (Ni) from soils and accumulate this metal in their foliage. Hydrometallurgical processes have been developed to recover Ni in the form of metal or salts, starting from the plant A. murale. They include: (1) a combustion step, to obtain ash containing 15–20% Ni; (2) a leaching step; and (3) purification. That whole flowsheet has been thoroughly investigated, and the processes scaled up to the pilot scale. Another strategy is presented here, consisting of recovering Ni without burning the plant. Ni can be extracted from the dry plant by water leaching, but the leachate is a multi-element solution from which Ni has to be separated. Selective precipitation of Ni hydroxide is not possible since Ni is bound to organic ligands. In this work, the plant leachate is processed by adsorption on the chelating resin DOWEXTM M4195. The results showed that Ni was selectively retained whereas the other main cations were not. Nickel could be recovered at the elution step. This methodology needs to be further investigated but these initial results are very encouraging and open the possibility of Ni recovery by agromining.

By Anna Franzkowiak, Dean Gregurek, Alfred Spanring, Angelika Ressler

In order to determine the most suitable refractory products and improve the lining lifetime for the diverse furnaces used in the nonferrous metal industry, corrosion tests are performed at RHI’s Technology Center. The practical facilities include the cup test, induction furnace, rotary kiln, and drip slag test described in this paper, which enable a comprehensive understanding of the chemo-thermal brick wear on a pilot scale. The corrosion trials are performed with actual slags generated during operations at a customer’s plant. To determine the highest influencing wear parameter, every single test is combined with a detailed mineralogical investigation and thermochemical calculations performed using FactSage. Based on the results, tailored refractory solutions for the nonferrous metal industry can be provided in combination with trials conducted at the customer’s site.

Jan 1, 2014

By C. Damiani

The Chuquicamata smelter, operating since 1952, has gone through several developing stages which have been characterized by the addition of peak technology for copper concentrate smelting (Teniente converter and Outokumpu flash furnace) with an intensive use of technical oxygen, which has permit-ted to partially discontinue the reverberatory furnace utilization. This paper shows the main indicators and operational practices at present, as well as those concerning maintenance aspects. Finally, the most relevant topics related to the future development of the smelter are mentioned with special remarks on the Decontamination Plan, which allows US to keep the high level of production, reducing the emission of contaminants according to the legal requirements in force.

Jan 1, 1993

By Fabio J. Esper, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Cassio P. Carvalho, Giorgio Grotti, Reginaldo B. Santos

"Rejected sands from smelting metallurgical process because contain lead and others heavy metals are a problem to dispose as waste in all the countries. A procedure that is being proposed for it is to incorporate it on common clay bodies in the fabrication of structural ceramic products as bricks, blocks and roof tiles. The main goal of this paper is to present the results obtained with mixtures of sands from smelting metallurgical process with common clay from Jundiaí, São Paulo, Brazil. Preliminary incorporation tests (1,0% in weight) were made with hand formed spherical samples. With the higher compression strength of the spheres after drying and firing (950ºC) experiments on bricks production were made for quality technological test. Seven hundred hallow blocks containing 1,0% waste were produced and presented ceramic properties similar to those without sand incorporation. Introduction In last the fifteen years the LMPSol - Raw Materials & Non-metallic Solids Laboratory – Metallurgic Eng. & Materials Depto. – Polytechnic School - University of São Paulo comes studying the possibilities of incorporate industrials waste materials to the production of bricks and other products of construction aiming at to remove pollution products of the environments and to user the properties of the same ones in the structural ceramics products. Examples are the study of the influence of rejected steel furnace dusts in structural ceramic [1], another example is the main subject of the present paper: use of rejected sand from smelting metallurgical process in the production of bricks an other products of structural ceramics. Antecedents More or less one year ago, specialist and members from the direction board of METALÚRGICA GROFE LTD. Company contacted researchers and professors of the LMPSol – PMT – EPUSP seeking for a solution to their concern with the disposal of rejected sand from smelting metallurgical process."

Jan 1, 2008

By S. Niyomwas, R. G. Reddy

"A mathematical model was developed to describe the plasma gas and particle dynamics and conversion yields. The velocity and temperature fields in the plasma were calculated by solving 1 the Navier-Stokes equations and the thermal energy balance equations. Conservation equations for the system species consider the multi-component diffusion and chemical reactions. Through the application of this model, temperature distribution, flow fields, and production rates were computed. The model was used to study the thermal decomposition of ilmenite in the non-transferred arc plasma reactor. The computed production rates of TiN from ilmenite using nitrogen and methane gas mixtures, are in the range of 5 to 100 x 104 kg/m3/s at 2500 KIntroductionThe widespread interest in thermal plasma processing has stimulated a great deal of research effort into the various aspects of this process, including plasma' spraying, thermal plasma chemical vapor deposition, plasma synthesis of fine powders, thermal plasma decomposition, plasma melting, and plasma extractive metallurgy.In the plasma synthesis of fine powders, the earlier experimental and theoretical studies aimed at predicting the final products1-5. Then it was followed by more recent investigation concerning the profile of plasma gas velocity, plasma temperature and concentration. In this regard, useful plasma processing models have been reported by numerous investigation6 -11 which were increased by both theoretical analysis and measurement.As a result of this work a reasonable plasma-processing model is proposed. It is to be noted that all the thermal analysis that has been made neglected the fluid -flow effects. Also, in the analysis aimed at the quantitative description of the fluid-flow field, the effect of heat transfer was not taken into account."

Jan 1, 2000

By Lichao Ding, Jingbiao Fan, Yunnen Chen

"With the development of industrial production, more and more wastewater containing high concentration ammonia nitrogen was discharge into the environmemt, which caused serious harm to the environmemt. Treating the wastewater has great significance to protect water resources. Using air-stripping combined with oxidation to uptake high concentration of ammonia nitrogen wastewater. The influence of operating parameters was investigated. Experimental results revealed that pH of solution, aeration time and aeration strength showed heavy influence on ammonia nitrogen removal. Air-stripping combined with oxidation can be considered as an alternative approach for the removal of high concentration of ammonia nitrogen from practical metallurgical wastewater. When pH was 11, aeration time 20 min, aeration strength 1040 Lh-1, and oxidation with 10 % NaClO solution 10 min, the initial ammonia nitrogen 2130 mgr1 could reduce to 12 mgr1. Other items could also be removed to meet the ""Integrated wastewater discharge standard (GB8978-88)"".1. IntroductionThe rapid development of human activities has caused a worldwide increase of nitrogen in rivers, lakes and coastal waters. It leads to considerable eutrophication and an increase in the frequency of toxic algae blooms [1,2]. The concentrations of nitrogen in the water of China are pervading high [3]. The discharge of wastewater containing high concentration of ammonia nitrogen is one of the most important factors. Great efforts have been devoted to the removal of ammonia nitrogen from wastewater. Traditional methods include biological denitrication [ 4 ], chemical precipitation with magnesium ammonium phosphate [5], electrochemical conversion [6], air-stripping [7] and so on. Biological denitrication is the most common process in the treatment of ammonia nitrogen wastewater. But the process is only suitable for the removal of relatively low ammonia concentration due to the requirement of appropriate C/N ratio [8]. Chemical precipitation needs additional reagents, which may introduce new pollutants to water body. Electrochemical method often uses expensive metal or metal oxide as electrodes, and also consumes large quantity of energy [6].Although air-stripping makes use of stripping tower and consumes energy, it is very suitable for the removal of relatively high ammonia concentration. Different air-stripping conditions would appear different removal efficiency. And only air-stripping the effluent can not be attained the ""Integrated wastewater discharge standard (GB8978-88)"". In this study, we use air-stripping and oxidation to removal high concentration of ammonia nitrogen from simulated and real ammonia nitrogen wastewater."

Jan 1, 2011

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In order to produce good quality ammonium paratungstate, Sn needs be removed efficiently from the tungstate processing solution. The nascent hydrous ferric oxide has excellent adsorption ability and is often used as an adsorbent to remove metal ions from aqueous solution. In this paper, nascent hydrous ferric oxide is used to remove Sn from tungstate solution. Through experimental, the effects of pH value, reagent amount of adsorbent, reaction temperature and reaction time on the Sn removal are investigated. The study shows that 98% of Sn can be removed effectively from sodium tungstate solution and only 2% of W is lost during process under the conditions of pH 9~12, reagent amount of Fe addition 40 times Sn amount, reaction time 30min and room temperature. As the Fe addition reaches 90 times of Sn concentration in the ammonium tungstate solution, 99% of Sn is removed and APT with zero level purity national standard is obtained.

Jan 1, 2014